Pelco EM1109/EM2000/ EM2200 Enclosure Mount Installation guide

Pelco
Brand
Pelco
Model
EM1109/EM2000/ EM2200 Enclosure Mount
Type
Installation guide

Pelco EM1109/EM2000/ EM2200 Enclosure Mount is a versatile mounting solution for enclosures with a 5.08 cm (2-inch) mounting hole pattern. It can be installed on a horizontal or vertical pipe or pole that has a 7.62 cm (3-inch) to 20.32 cm (8-inch) diameter. The fully adjustable swivel heads allow 360-degree horizontal movement and cable feedthrough to conceal wiring. The EM1109 is a medium duty pedestal mount for horizontal pipe or pole mounting, while the EM2000 is a medium duty 90-degree J-mount for vertical pipe/pole mounting.

Pelco EM1109/EM2000/ EM2200 Enclosure Mount is a versatile mounting solution for enclosures with a 5.08 cm (2-inch) mounting hole pattern. It can be installed on a horizontal or vertical pipe or pole that has a 7.62 cm (3-inch) to 20.32 cm (8-inch) diameter. The fully adjustable swivel heads allow 360-degree horizontal movement and cable feedthrough to conceal wiring. The EM1109 is a medium duty pedestal mount for horizontal pipe or pole mounting, while the EM2000 is a medium duty 90-degree J-mount for vertical pipe/pole mounting.

INSTALLATION
C207M-H (12/17)
EM1109/EM2000/
EM2200
Enclosure Mounts
2 C207M-H (12/17)
Important Safety Instructions
1. Installation and servicing should be done only by qualified service personnel and conform to all local codes.
2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials.
3. Use only installation methods and materials capable of supporting four times the maximum specified load.
4. Use stainless steel hardware to fasten the mount to outdoor surfaces.
Description
The EM1109/EM2000/EM2200 enclosure mounts have been engineered for use with all enclosures with a 5.08 cm (2-inch) mounting hole
pattern. They can be installed on a horizontal or vertical pipe or pole that has a 7.62 cm (3-inch) to 20.32 cm (8-inch) diameter.
These enclosure mounts feature fully adjustable swivel heads, allowing 360-degree horizontal movement and cable feedthrough to conceal
wiring.
EM1109 Medium duty pedestal mount for horizontal pipe or pole mounting; will work on vertical pipe/pole mounting; manually
adjustable swivel head; 22.63 cm (8.91 inches) long
EM2000 Medium duty 90-degree J-mount for vertical pipe/pole mounting; manually adjustable swivel head; 37.46 cm (14.75 inches) long
EM2200 Medium duty “hook” mount for horizontal pipe/pole mounting; manually adjustable swivel head; 47.5 cm (18.7 inches) long
Installation
The EM1109/EM2000/EM2200 enclosure mounts include two 1/4-20 x 0.500 hex head bolts to mount the enclosure and three stainless steel
straps for attaching the mount to the pole or pipe.
1. Insert the stainless steel straps through the slots in the mount bracket. Position the mount on the pole or pipe and attach it to the pole with
the stainless steel straps (supplied). Tighten the strap screws securely.
2. Attach the enclosure or camera securely with the two 1/4-20 bolts (supplied).
3. Loosen the bolts on the swivel head and adjust the pan rotation (360 degrees) and tilt angle (75 degrees up or down). Retighten the bolts
and lock the mount into place.
Specifications
Pan Adjustment Unlimited 360°
Tilt Adjustment ±75°
Construction Aluminum
Finish White epoxy powder coat
Locking Method 3/8-16 hex head bolts
Enclosure Mounting 2, 1/4-20 mounting bolts (supplied)
Suggested Mounting Method Slots are provided to allow the use of straps for mounting to pole or pipe; 3 stainless steel straps are
supplied.
Maximum Load 18 kg (40 lb)
WARNING: Make certain the pole or pipe is capable of supporting the full load of the mount, enclosure, and camera.
WARNING: Only mount one camera system per set of stainless steel straps and do not over/under torque.
Stainless steel straps installation torque: 35-45in.lbs.
C207M-H (12/17) 3
NOTE: VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS.
20.32
(8.00)
24.26
(9.55)
3.81
(1.50)
7.62
(3.00)
5.08
(2.00)
0.69 (Ø 0.272), 7X
4.42
(1.74)
10.41
(3.40)
EM1109
EM2000
37.47 (14.75)
30.48
(12.00)
4.83
(1.90)
3.81
(1.50)
7.62
(3.00)
5.08
(2.00)
0.69 (Ø 0.272), 7X
4.42
(1.74)
10.41
(3.47)
0.69 (Ø 0.272), 7X
8.81
(3.47)
4.42
(1.74)
5.08
(2.00)
3.81
(1.50)
7.62
(3.00)
25.91
(10.20)
47.50
(18.70)
30.48 (12.00)
EM2200
WARRANTY STATEMENT
For information about Pelco’s product warranty and thereto related information, refer to www.pelco.com/warranty.
Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. © Copyright 2017, Pelco, Inc.
ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies. All rights reserved.
Product specifications and availability are subject to change without notice.
Pelco, Inc. 625 W. Alluvial Fresno, California 93711 United States
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120
www.pelco.com www.pelco.com/community
REVISION HISTORY
Manual # Date Comments
C207M-C 7/99 Revised to new format. Created service manual (C207SM) for exploded assembly and parts list.
C207M-D 7/03 Revised dimensions of EM2000 and EM2200 per ECO 03-8731.
C207M-E 12/05 Revised to new format. Updated pole diameter for stainless steel mounting straps per CAR 05-0928.
C207M-F 1/08 Revised mounting head hole pattern per ECO 07-17992. Added RoHS statement.
C207M-G 4/14 Updated graphics and content for metric (imperial) dimension display. Changed screw size.
C207M-H 12/17 Added warning to the pole mount adapter instructions.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Pelco EM1109/EM2000/ EM2200 Enclosure Mount Installation guide

Pelco
Brand
Pelco
Model
EM1109/EM2000/ EM2200 Enclosure Mount
Type
Installation guide

Pelco EM1109/EM2000/ EM2200 Enclosure Mount is a versatile mounting solution for enclosures with a 5.08 cm (2-inch) mounting hole pattern. It can be installed on a horizontal or vertical pipe or pole that has a 7.62 cm (3-inch) to 20.32 cm (8-inch) diameter. The fully adjustable swivel heads allow 360-degree horizontal movement and cable feedthrough to conceal wiring. The EM1109 is a medium duty pedestal mount for horizontal pipe or pole mounting, while the EM2000 is a medium duty 90-degree J-mount for vertical pipe/pole mounting.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers