Pelco MM22 Enclosure Mount Installation guide
- Category
- Security camera accessories
- Type
- Installation guide
INSTALLATION
C228M-B (4/14)
MM22
Enclosure Mount
C228M-B (4/14) 3
Important Safety Instructions
1. Installation and servicing should be done only by qualified service personnel and conform to all local
codes.
2. Installation shall be done in accordance with all local and national electrical and mechanical codes
utilizing only approved materials.
3. Use only installation methods and materials capable of supporting four times the maximum
specified load.
4. Use stainless steel hardware to fasten the mount to outdoor surfaces.
To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply The
product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present within
this unit.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation and
operation.
Description
The MM22 pedestal/wall mount has been engineered for use with light-to-medium weight cameras and
various Pelco enclosures having a 5.08 cm (2-inch) mounting hole pattern. The MM22 can be installed on a
ceiling or any horizontal surface and will support up to 18 kg (40 lb). The MM22 features a fully adjustable
swivel head, allowing 360-degree, horizontal movement.
Parts List
User-Supplied Parts List
Qty Description
1 MM22 pedestal/wall mount with mounting hardware
2 1/4-20 x 0.500 hex head bolts
2Flat washers
2 Split washers
Qty Description
4 Fasteners; minimum 6 mm (1/4-inch) diameter recommended
1 Appropriate water-tight sealant, if installing the product outdoors
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
4 C228M-B (4/14)
Installing the Mount
If you are installing the mount outdoors, stainless steel hardware is recommended.
1. Drill holes in the mounting surface using the mount as a template, and then attach the mount
securely with the required fasteners (not supplied).
2. Attach the enclosure or camera securely to the mount with the two 1/4-20 x 0.500 hex head bolts
(supplied).
3. Loosen the 3/8-16 hex head bolts on the swivel head and adjust for pan rotation (360 degrees) and
tilt angle (75 degrees, up or down).
4. Retighten the hex head bolts to lock the mount into place.
WARNINGS:
• Make certain the mounting surface can support the full load of the mount, enclosure,
and camera.
• When installing the mount outdoors, seal the bolt holes with an appropriate sealant to
prevent water damage to the mounting surface. Apply the sealant around the bolt holes
located between the mount and the mounting surface.
C228M-B (4/14) 5
Specifications
MODEL
MM22 Pedestal/wall mount; for use with light-to-medium weight
cameras and Pelco enclosures with a 5.08 cm (2-inch)
mounting hole pattern.
MECHANICAL
Suggested Mounting Method Secure to solid surface with 4 fasteners; minimum 6 mm
(1/4-inch) diameter recommended. (user supplied)
Enclosure Mounting 2 each: 1/4-20 x 0.500 hex head bolts, flat washers, and split
washers (supplied)
Locking Method 3/8-16 hex head bolts
Pan Adjustment Unlimited 360°
Tilt Adjustment ±75° (up or down)
GENERAL
Construction Aluminum billet with aluminum, adjustable head
Finish Gray polyester powder coat
Maximum Load 18 kg (40 lb)
Unit Weight 1.18 kg (2.6 lb)
NOTE: VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS.
8.81
(3.47)
4.42
(1.74)
5.08
(2.00)
Ø 0.68 (0.27), 7X
18.00
(7.09)
Ø 5.08 (2.00)
Ø 15.24
(6.00)
Ø 0.94 (0.37), 4X
EQ SP ON A
12.06 (4.75) BC
3.81
(1.50)
7.62
(3.00)
6 C228M-B (4/14)
WARRANTY STATEMENT
For information about Pelco’s product warranty and thereto related information, refer to www.pelco.com/warranty.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive
2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE).
Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual # Date Comments
C228M 3/99 New; removed instructions from C227M manual to create separate manual for MM22.
C228M-A 1/08 Revised to new format. Revised mounting head hole pattern per ECO 07-17992.
C228M-B 3/14 Revised to new format. Updated for hardware change and displayed dimensions in graphics.
Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates.
All other product names and services are the property of their respective companies. ONVIF and the ONVIF logo are trademarks of ONVIF Inc.
Product specifications and availability are subject to change without notice. © Copyright 2014, Pelco, Inc. All rights reserved.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Pelco MM22 Enclosure Mount Installation guide
- Category
- Security camera accessories
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Pelco MM22 User manual
-
-
-
-
-
-
-
-
-