Page is loading ...
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet from the
support that Philips offers, register your product at www.philips.com/welcome.
General description (Fig. 1)
A Cap of lling opening
B Steam control
- 1 = minimum steam
- 2 = maximum steam
- t= no steam
- u= Calc-Clean function
C Temperature light
D Mains cord
E Water tank
F Soleplate
G Temperature dial
Important
Read this user manual carefully before you use the appliance and save it for future
reference.
Danger
- Never immerse the iron in water.
Warning
- Check if the voltage indicated on the type plate corresponds to the local mains
voltage before you connect the appliance.
- Do not use the appliance if the plug, the mains cord or the appliance itself shows
visible damage, or if the appliance has been dropped or leaks.
- If the mains cord is damaged, you must have it replaced by Philips, a service
centre authorised by Philips or similarly qualied persons in order to avoid a
hazard.
- Never leave the appliance unattended when it is connected to the mains.
- This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the
appliance.
- Do not let the mains cord come into contact with the hot soleplate of the iron.
Caution
- If the appliance has an earthed plug, it must be plugged into an earthed wall
socket.
- Check the mains cord regularly for possible damage.
- The soleplate of the iron can become extremely hot and may cause burns if
touched.
- When you have nished ironing, when you clean the appliance, when you ll or
empty the water tank and also when you leave the iron even for a short while:
set the steam control to the ‘no steam’ position, put the iron on its heel and
remove the mains plug from the wall socket.
- Always place and use the iron on a stable, level and horizontal surface.
- This appliance is intended for household use only.
Electromagnetic elds (EMF)
This Philips appliance complies with all standards regarding electromagnetic elds
(EMF). If handled properly and according to the instructions in this user manual, the
appliance is safe to use based on scientic evidence available today.
Before first use
1 Remove any sticker or protective foil from the soleplate.
2 Let the iron heat up to maximum temperature.
3 Pass the iron over a piece of damp cloth for several minutes to remove any
residues from the soleplate.
Note: The iron may give off some smoke when you use it for the rst time. This ceases
after a short while.
Preparing for use
Filling the water tank
Never immerse the iron in water.
1 Make sure the appliance is unplugged.
2 Set the steam control to the ‘no steam’ position (Fig. 2).
3 Tilt the iron backwards.
4 Openthecaptheofllingopening(Fig.3).
5 Fill the water tank with tap water up to the maximum level. (Fig. 4)
DonotllthewatertankbeyondtheMAXindication.
Do not put perfume, vinegar, starch, descaling agents, ironing aids or other
chemicals in the water tank.
Note: If the tap water in your area is very hard, we advise you to mix it with an equal
amount of distilled water or to use distilled water only.
6 Closethecapofthellingopening.
Setting the temperature
1 Put the iron on its heel.
2 To set the required ironing temperature, turn the temperature dial to the
appropriate position (Fig. 5).
Check the laundry care label for the required ironing temperature:
1 Synthetic fabrics (e.g. acrylic, viscose, polyamide, polyester)
1 Silk
2 Wool
3 Cotton, linen
If you do not know what kind or kinds of fabric an article is made of, determine the
right ironing temperature by ironing a part that is not visible when you wear or use
the article.
Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent
shiny patches.
Start ironing the articles that require the lowest ironing temperature, such as those
made of synthetic bres.
3 Put the mains plug in an earthed wall socket.
, The temperature light goes on (Fig. 6).
4 When the temperature light has gone out, wait a while before you
start ironing.
The temperature light goes on from time to time during ironing.
Using the appliance
Steam ironing
1 Make sure that there is enough water in the water tank.
2 Select the recommended ironing temperature (see chapter ‘Preparing for use’,
section ‘Setting the temperature’).
3 Afterthetemperaturelighthasgoneout,setthesteamcontroltothe
appropriate steam position. Make sure that the steam setting you select is
suitable for the ironing temperature selected: (Fig. 7)
Temperature settings 2 to 3 for minimum steam 1.
Temperature settings 3 to MAX for maximum steam 2.
The iron starts to produce steam as soon as it reaches the set temperature.
Ironing without steam
1 Set the steam control to the ‘no steam’ position (Fig. 2).
2 Select the recommended ironing temperature (see chapter ‘Preparing for use’,
section ‘Setting the temperature’).
Cleaning and maintenance
After ironing
1 Remove the mains plug from the wall socket and let the iron cool down.
2 Wipe scale and any other deposits off the soleplate with a damp cloth and a
non-abrasive (liquid) cleaner.
To keep the soleplate smooth, avoid hard contact with metal objects. Never use a
scouring pad, vinegar or other chemicals to clean the soleplate.
3 Clean the upper part of the appliance with a damp cloth.
4 Regularly rinse the water tank with water. Empty the water tank after cleaning.
Calc-Clean function
Use the Calc-Clean function once every two weeks. If the water in your area is very
hard (i.e. when akes come out of the soleplate during ironing), use the Calc-Clean
function more frequently.
1 Set the steam control to the ‘no steam’ position (Fig. 2).
2 SetthetemperaturedialtoMAX.
3 Fill the water tank to the maximum level.
Do not pour vinegar or other descaling agents into the water tank.
4 Put the mains plug in the wall socket.
ENGLISH
2
4239.000.7060.4
5 Unplug the iron when the temperature light goes out.
6 Hold the iron over the sink and set the steam control to the Calc-Clean
position .
7 Hold the steam control at the Calc-Clean position and gently shake the iron
until all the water in the tank has been used up (Fig. 8).
, Steamandboilingwatercomeoutofthesoleplate.Scale(ifany)isushedout.
8 AfteryouhaveusedtheCalc-Cleanfunction,setthesteamcontroltothe‘no
steam’ position.
9 Repeat the Calc-Clean process if the water that comes out of the iron still
contains scale particles.
After the Calc-Clean process
1 Connect the iron to the mains to let the soleplate dry.
2 Unplug the iron when the temperature light goes out.
3 Move the iron gently over a piece of used cloth to remove any water stains
that have formed on the soleplate.
4 Let the iron cool down before you store it.
Storage
1 Unplug the appliance and set the steam control to the ‘no steam’ position.
2 Empty the water tank (Fig. 9).
3 Wind the mains cord round the cord storage facility. (Fig. 10)
4 Store the iron on its heel in a safe and dry place.
Environment
- Do not throw away the appliance with the normal household waste at the end
of its life, but hand it in at an ofcial collection point for recycling. By doing this,
you help to preserve the environment (Fig. 11).
Guarantee & service
If you need service or information or if you have a problem, please visit the Philips
website at www.philips.com or contact the Philips Consumer Care Centre in your
country (you nd its phone number in the worldwide guarantee leaet). If there is
no Consumer Care Centre in your country, go to your local Philips dealer.
Troubleshooting
This chapter summarises the most common problems you could encounter with your
iron. If you are unable to solve the problem, contact the Consumer Care Centre in
your country.
Problem Cause Solution
The iron is plugged
in but the soleplate
is cold.
There is a connection
problem.
Check the mains cord, the plug and
the wall socket.
The temperature dial
is set to MIN.
Set the temperature dial to the
required temperature.
The iron does
not produce any
steam.
There is not enough
water in the water
tank.
Fill the water tank (see chapter
‘Preparing for use’).
The steam control is
set to the ‘no steam’
position.
Set the steam control to a steam
setting (see chapter ‘Using the
appliance’).
Water leaks from
the soleplate
during ironing.
The iron is not hot
enough.
Set the temperature dial to a
temperature suitable for steam
ironing (
2 to MAX). Put the
iron on its heel and wait until the
temperature light goes out before
you start ironing.
Flakes and
impurities come
out of the
soleplate during
ironing.
You have used hard
water, which has
caused scale akes
to develop inside the
soleplate.
Use the Calc-Clean function one or
more times (see chapter ‘Cleaning
and maintenance’).
Water leaks from
the soleplate while
the iron cools
down or after it
has been stored.
You have put the iron
in horizontal position
while there is still
water in the water
tank.
Empty the water tank and set the
steam control to the ‘no steam’
position before you store the iron
(see chapter ‘Storage’). Store the
iron on its heel.
3
4239.000.7060.4
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Philips GC1420/02 User manual
- Category
- Irons
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Tefal FV9650M0 User manual
-
Electrolux EDI130 User manual
-
Tefal FV5370G0 User manual
-
-
-
-
-
-
Tefal DV8630K0 User manual
-