GE GTUN275EM0WW Installation guide

Brand: GE

Model: GTUN275EM0WW

Category: Washing machines

Type: Installation guide

Installation

Instructions

--i@

Unitized Gas

Washer/Dryer

Questions on installation? Call: 1-800-GECARES (US}or Visit our Web site at: www.GEAppliunces.com (US).

In Canada, call 800-561-3344 or visit www.GEAppliunces.cu.

BEFOREYOU BEGIN

Readthese instructions completely and

carefully.

•IMPORTANT-Save these instructionsfor

localinspector'suse.

•IMPORTANT- Observe all governing

codesand ordinances.

• Note to Installer - Be sure to leave these

instructionswith thecustomer.

• Note to Customer - Keepthese instructions

with your Use and Care Book for future

reference.

• Beforethe appliance isremovedfrom service

or discarded, remove the washer and dryer

door.

•inspectthedryerexhaustoutlet andstraighten

theoutlet walls iftheyare bent.

• Service information and the wiring diagram

are locatedat theaccesspanel.

• Do not allow childrenon or in the appliance.

Close supervision of children is necessary

whentheapplianceisusednear children.

• Install the dryer where the temperature is

above50°F(].O°C)for satisfactoryoperationof

thedryercontrolsystem.

WARNING RISK OF FIRE

, Toreducetheriskofsevereinjuryordeath,followallinstallationinstructions.

. Applianceinstallationmustbeperformedbyaqualifiedinstaller.

. Installtheclothesapplianceaccordingtotheseinstructionsandinaccordancewithlocal

codes.Intheabsenceof localcodes,installationmustcomplywith NationalFuelGas

Code,ANSIZ223.1/NFPA54ortheCanadianNaturalGasandPropaneInstallationCode,

CSAB149,1,

,CalifomiaSafeOnnkingWaterandToxicEnforcementAct.

Thisact requiresthegovernorofCaliforniatopublisha listofsubstancesknowntothe

statetocausecancer,birthdefectsorotherreproductiveharmandrequiresbusinesses

to warn customersof potentialexposureto suchsubstances.Gasappliancescan

causeminorexposuretofourofthesesubstances,namelybenzene,carbonmonoxide,

formaldehydeandsoot,causedprimarilybytheincompletecombustionofnaturalgas

or LPfuels.Properlyadjusteddryerswillminimizeincompletecombustion.Exposureto

thesesubstancescanbeminimizedfurtherbyproperlyventingthedryertotheoutdoors.

, Thisappliancemustbeexhaustedtotheoutdoors.

, Useonly4"rigidmetalductingforexhaustingtheappliancetotheoutdoors.

, DONOTinstalla clothesdryerwithflexibleplasticductingmaterials.If flexiblemetal

(semi-rigidorfoiFtype)ductisinstalled,it mustbeULlistedandinstalledinaccordance

withtheinstructionsfoundin"ConnectingTheDryerToHouseVent"onpage8 ofthis

manual.Flexibleventingmaterialsareknowntocollapse,beeasilycrushed,andtraplint.

Theseconditionswillobstructdryerairflowandincreasetheriskoffire.

, Donotinstallorstorethisapplianceinanylocationwhereitcouldbeexposedtowater

andorweather.

, Savetheseinstructions.(Installers:Besuretoleavetheseinstructionswiththecustomer).

TOOLS YOU WILL NEED

{x2I

i0" ADJUSTABLEWRENCHES _._

8"PIPEWRENCH LEVEL

SUPJOINTPUERS FLATBLADESCREWDRIVER

1/4" Nutdriver

MATERIALS YOU WILL NEED

4'IDIA.METALDUCT

(RECOMMENDED) 4'IDIAMMETALELBOW

4"DIA.FLEXIBLEMETAL(SEMI-RIGID)

ULLISTEDTRANSITIONDUCT

(IFNEEDED)

KITWXO8XlO077(INCLUDES2ELBOWS)

4"DIA.FLEXIBLEMETAL(FOILTYPE)

ULLISTEDTRANSITIONDUCT

(IFNEEDED.)

EXHAUSTHOOD

(x2)

4"DUCTCLAMPS

4"SPRINGCLAMPS

PIPE

COMPOUND SOAPSOLUTION

FORLEAKDETECTION

DUCTTAPE

FLEXIBLEGASLINECONNECTOR

SAFETYGLASSES

GLOVES

4"COVERPLATE(IFNEEDED)

(KITWEIM454)

In the state of Massachusetts:

• Installation must be performed by

e qualifledor licensed contractor,

plumber, or gesfltter qualified or

licensed by the state.

• When using bell-type gas shut-off

valves, they shell be T-handle type.

• A flexible gas connector, when used,

must not exceed 3 feet.

1.Cable Tie

PARTS SUPPLIED

2 Washer Hoses

% O

2 Stainer Screens

2 Rubber Washers Rubber Washers

(washers may be in water hoses)

Printedinlexico 233D1835PO01 31-16655-6 12-12 GE

Installation

INSTALLATION REQUIREMENTS LOCATION

Thisappliance must beinstalled on firm flooring to minimize

vibration during spin cycle. Concrete flooring is best, but

wood base issufficient, provided floor support meets FHA

standards. This appliance should not be installed on rugs

or exposed to weather.

PLUMBING

WATERPRESSURE- Must be 20 psi minimum to 120 psi

maximum.

WATERTEIVlPERATURE- Household water heater should be

set to deliver water at 120° to 150°F (50° to 66°C)INTHE

WASHERwhen hot wash is selected.

SHUTOFFVALVES-Bothhot and cold shutoffvalves (faucets)

should be supplied.

DRAIN- Water may be drained into standpipe or set tub.

Discharge height MUSTNOT BE LESSTHAN 30 INCHES,

and no more than 6 feet above the base of the washer.

Standpipe must be 1-!/2 inches minimum inside diameter

and must be open to atmosphere.

nstructions

ELECTRICAL REQUIREMENTS

CAUTION: Beforeplugging in washer, read the following

electrical requirements.

CAUTION: Forpersonal safety, do not use anextension

cord or adapter plug with this appliance. Donot, under any

circumstances, cut or remove the third grounding prong

from the power cord. Follow national electrical codes and

ordinances. Thisappliance must besupplied with the voltage

and frequency indicated on the rating plate (located at the

top of the dryer front panel),and connected to an individual,

properly grounded branch circuit, protected by a 15- or 20-

amp circuit breaker or time-delay fuse. If the electric supply

provided does not meet the above requirements, call a

licensed electrician.

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Verify Your Gas Installation (seesection 2).

Prepare the Area and Exhaust for Installation of

appliance (seesection 1).

Check and Insure the Existing External Exhaust

is Clean (seesection 1)and Meets Attached

Installation Specifications (seesection 6).

Remove the Foam Shipping Pads(seesection 1).

Move the appliance to the Desired Location.

Levelyour appliance (seesection 8).

Connect the Gas Supply (seesection 3) and check

for leaks (seesection 4).

Connect the External Exhaust (seesection 7).

Connect to plumbing facilities (seesection 11).

Step 10 Connect the Power Supply (seesection 5).

Step 11 Check the Operation of the Power Supply,Gas

Connections, and Venting.

Step 12 Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed Bythe Owner.

For Alcove or Closet Installation see section 1:3.

For Bathroom or Bedroom Installation seesection 14.

For Mobile or Manufactured Home see section 12.

ADJUSTING FOR ELEVATION

. Gas clothes dryers input ratings are based on sea level

operation and need not be adjusted for operation at

or below 2000 ft. elevation. For operation at elevations

above 2000 ft., input ratings should be reduced at a rate

of 4 percent for each 1000 ft. above sea level.

. Installation must conform to local codes and ordinances

or, in their absence with the National Fuel Gas Code,

ANSI Z22:3.1/NFPA54, or the Natural Gas and Propane

Installation Code,CSAB149.1.

Installation Instructions

51"

24" NOMINAL PRODUCT DIMENSIONS

_---'23.75"----_

W(]ter Inlets

(reor)

* Dimension represents door closed including handle and knobs.

NOTE:With feet set at mid position, feet can be adjusted +_.575".

Gas Inlet

(Rearview of appliance)

27" NOMINAL PRODUCT DIMENSIONS

52.9"

0oolo o O

_._ Drc]in outlet

i (rec]r)

_-- 3.9"

_--- 26.8"

--12.5"

]

36.5"

W(]ter Inlets

_------'26.7"-----_

_47"_

4.35"

_------ 30.85"------_

* Dimension represents door closed including handle and knobs.

NOTE:With feet set at mid position, feet can be adjusted +_.575".

Gas Inlet

(Rec]rview of appliance)

Installation Instructions

Minimum Clearance Other Than Alcove or Closet Installation

Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and rear.Consideration

must be given to provide adequate clearance for installation and service.

I-_ PREPARING FOR INSTALLATION

OF NEW APPLIANCE

DISCONNECTING GAS

TURNGAS

SHUT-OFFVALVEI_ DISCONNECTANDDISCARDOLD,_._,

TOTHEOFF ___ FLEXIBLEGASCONNECTORAND

POS,T,ON OLDTRANS,T,ONDUCT,NG

MATERIAL.REPLACEWITHNEW

CSA(AGA)APPROVEDFLEXIBLE

GASLINECONNECTORANDUL

APPROVEDTRANSITIONDUCT.

WARNING - NEVERREUSEOLD

FLE×IBLE CONN ECTORS.

Theuse of old flexible connectors can cause leaks and

personal injury. Always use new flexible connectors

when installing gas appliances.

REMOVING LINT FROM WALL

EXHAUST OPENING

• Removeand discard existing plastic or metal foil

transition duct and replace with ULlisted transition duct.

_j WALL

INTERNAL_t_,].DUCT _ CHECKTHATEXHAUST

OPENING -'_-_ \ G "'.. HOODDAPIPEROPENS

ANDCLOSESFREELY.

TILTTHEAPPLIANCE

SIDEWAYSAND REMOVE

THE FOAMSHIPPINGPADS

BYPULLINGATTHESIDES

AND BREAKINGTHEMAWAY

FROMTHEAPPLIANCELEGS.

BESURETOREMOVEALL OF

THE FOAMPIECESAROUND

THE LEGS.

After the machine is in the home,

remove remaining packing material/

carton from washer.

DO NOT REMOVE SHIPPING ROD AT

THISTIME.

Removestyrofoam block. Removethe

bag containing theWasher hosesand

parts parts from tub. Put styrofoam

block back in tub opening to hold tub

in placeduring the rest of installation.

Hove washer close to final position.

Make sure there is at least a 24"

clearance on right side of washer to

remove shipping bar.PULLSHIPPING

BAROUT USINGYELLOWPLASTIC

HANDLE. Keep bar so it can be

reinstalled if washer is ever moved

again.

StyrofoamBlock

and Parts

Yellow

" Plastic

/ Handle

NEW HONE OR REMODELING FAUCETS/

DRAIN STANDPIPE/ELECTRICAL LOCATIO N

Right side of

Laundry Center

12"--_

_ .................. _|

Locate spigots, "

drain standpipe s3" |

and electrical plug |

in this area

FLOOR

I-_ GAS REQUIREMENTS

WARNING

, Installation must conform to local codes and

ordinances, or in their absence, with the National

Fuel Gas Code, ANSI Z223.1/NFPA 54, or the

Natural Gas and Propane Installation Code, CSA

B1491

. Thisgas dryerisequippedwitha Valve& Burner

Assembly foruse onlywith naturalgas Using

conversion kit WE25M73 for 24" Models or

WE25M74 for 27" Models,your localservice

organizationcan convertthisdryerforuse with

propane (LP)gas ALL CONVERSIONS MUST BE

MADE BY PROPERLY TRAINED AND QUALIFIED

PERSONNEL AND IN ACCORDANCE WITH LOCAL

CODES AND ORDINANCE REQUIREMENTS

• Theappliancemustbedisconnectedfromthegassupply

pipingsystemduringanypressuretestingofthatsystem

ata testpressureinexcessof05 PSI(34KPa)

• The appliancemustbe isolatedfromthegassupply

pipingsystembyclosingtheequipmentshutoffvalve

duringanypressuretestingofthegassupplypipingof

testpressureequaltoorlessthan05 PSI(34KPa)

27" GASSUPPLYCONNECTION

Note: 24" Gas supply connection has a flexible

hose thus dimensions will vary.

Installation Instructions

GAS SUPPLY

, A 1/8-in.National Pipe Taper thread plugged tapping,

accessible for test gauge connection, must be installed

immediately upstream of the gas supply connection to

the dryer, Contact your local gas utility should you have

questions on the installation of the plugged tapping.

. Supply line isto be 1/2-in. rigid pipe and equipped with

an accessible shut-off within 6 ft. of, and in the same

room with the dryer.

,Use pipe thread sealer compound or Teflon tape

appropriate for natural or LPgas.

, You must usewith this dryer a flexible metal connector

listed ANSI Z21.24 / CSA 6.10. The length of the

connector shall not exceed 3 ft.

, Connect flexible metal connector to dryer and gas

supply.

, Open shut-off valve.

RECONNECTING GAS

Listed connector ANSI Z21.24 / CSA6.10

BACK OF

APPLIANCE

24"

NEW METAL _.. _ _k_>4/ '_

FLEXIBLEGAS

LINECONNECTOR

2a" & 27"

INLET FROM

APPLIANCE

FLARE

ADAPTOR

27" ONLY

NEW METAL

FLEXIBLE GAS

LINE CONNECTOR

ADAPTOR

/8" NPT INLET

FROM APPLIANCE

27"ONLY

ELBOW

27" ONLY

NPT PIPE PLUG

FOR CHECKING GAS

INLET PRESSURE

SHUT-OFF VALVE

AT LEAST 1/2"

FLOOR

ITEHS NOT SUPPLIED

Note: The connector and fittings are designed for use only

on the original installation and are not to be reused for

another appliance or at another location. Keepflare end of

adaptor free of grease, oil and thread sealant.

CAUTION: Use adopters as shown. Connector nuts must

not be connected directly to pipe threads.

27"

APPLYPIPECOMPOUND

TOTHEADAPTORAND

APPLIANCEGASINLET.

TIGHTENTHEFLEXIBLEGASLINETO

THEADAPTORUSING2 ADJUSTABLE

WRENCHES.

APPLY PIPE COMPOUND TO

APPLIANCE INLET

24"

;HTEN THE FLEXIBLE GAS

LINE TO THE APPLIANCE

INLET USING 2 ADJUSTABLE

WRENCHES.

24" & 27"

_ APPLY PIPECOMPOUND

TO ALL MALE THREADS

24" & 27"

TIGHTEN ALL CONNECTIONS USING TWO

ADJUSTABLE WRENCHES.

DO NOT OVERTORQUE GAS CONNECTIONS!

Installation Instructions

[-4]LEAK TEST

I WARNING: NEVER USE AN OPEN

FLAME TO TEST FOR GAS LEAKS.

OPEN

GASVALVE.

Check oil connections for leakswith soapy solution or equivalent.

Apply soap solution. Bubbles indicate leaks. Leak test solution

must not contain ammonia which could cause damage to the

brass fittings, tfleak are found, close valve retighten thejaint and

repeat the soap test.

[_ELECTRICAL CONNECTION INFORMATION

WARNING - TO REDUCE THE

RISK OF FIRE, ELECTRICAL SHOCK,

AND PERSONAL INJURY:

. DO NOT USEAN EXTENSIONCORDORAN ADAPTER

PLUGWITH THISAPPLIANCE.

Dryer must be electrically grounded in accordance

with local codes and ordinances, or in the absence

of local codes, in accordance with the NATIONAL

ELECTRICALCODE,ANSI/NFPANO.70.

ELECTRICAL REQUIREMENTS

This appliance must be supplied with 120V, 60Hz, and

connected to u properly grounded brunch circuit,

protected by u 15- or 20- amp circuit breaker or time-

delay fuse. If electrical supply provided does not meet the

above specifications, it is recommended that a licensed

electrician install an approved outlet.

, WARNING - THIS DRYER IS

EQUIPPED A THREE-PRONG (GROUNDING)

PLUG FOR 'fOUR PROTECTION AGAINST

SHOCK HAZARD AND SHOULD BE PLUGGED

DIRECTLY INTO A PROPERLY GROUNDED

THREE-PRONG RECEPTACLE. DO NOT CUT

OR REMOVE THE GROUNDING PRONG FROM

THIS PLUG.

ENSURE PROPERGROUND EXISTSBEFORE USE.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk

of electric shock by providing u path of least resistance

of electric current. This appliance is equipped with a

cord having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into an

appropriate outlet that isproperly installed and grounded

in accordance with all local codes and ordinances.

WARN IN G - Improper connectionofthe

equipment-grounding conductor can result in a risk

of electric shock. Check with a qualified electrician

or serviceman if you are in doubt as to whether the

appliance is properly grounded.

Do not modify the plug provided with the appliance. If it

will not fit the outlet, have a proper outlet installed by a

qualified electrician.

_-I EXHAUST INFORMATION

I WARNING - IN CANADA AND IN THE

UNITED STATES,THE REQUIRED EXHAUST DUCT

DIAMETER IS 4 IN (102ram). DO NOT USE DUCT

LONGER THAN SPECIFIED IN THE EXHAUST

LENGTH TABLE.

Using exhaust longer than specified length will:

• Increase the drying times and the energy cost.

Reducethe dryer life.

Accumulate lint, creating a potential fire hazard.

The correct exhaust installation is YOUR

RESPONSIBILITYoProblems due to incorrect installation

are not covered by the warranty.

Remove and discard existing plastic or metal foil

transition duct and replace with ULlisted transition duct.

The MAXIMUMALLOWABLEduct length and number of

bends of the exhaust system depends upon the type of

duct, number of turns, the type of exhaust hood (wall

cap), and all conditions noted below. The maximum duct

length for rigid metal duct isshown in the table below.

Installation instructions

Use only for short

run installations

No. of 900 Rigid Rigid

Elbows Metal Metal

O 56 Feet 42 Feet

i 48 Feet 34 Feet

2 40 Feet 26 Feet

3 32 Feet 18 Feet

24" DRYEREXHAUSTLENGTH

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Recommended Use only for short

run installations

No. of 900 Rigid Rigid

Elbows Metal Metal

O 45 Feet 56 Feet

i 53 Feet 26 Feet

2 24 Feet 16 Feet

EXHAUST INFORMATION (CONT.)

27" DRYEREXHAUSTLENGTH

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Recommended

, For every extra 90° elbow, reduce the allowable vent

system length by 10ft.

, Two 45°elbows will be treated likeone 90°elbow. Forthe

sideexhaust installations,add one 90°elbow tothe chart.

, The total vent system length includes all the straight

portions and elbows of the system (transition duct

included).

EXHAUST SYSTEM CHECK LIST

HOOD ORWALL CAP

, Terminate in a manner to prevent back drafts or entry

of birds or other wildlife.

, Termination should present minimal resistance to

the exhaust air flow and should require little or no

maintenance to prevent clogging.

, Never install u screen in or over the exhaust duct. This

could cause lint build up.

, Wall cups must be installed at least 12 in.above ground

level or any other obstruction with the opening pointed

down.

SEPARATIONOFTURNS

For best performance, separate all turns by at least 4

ft. of straight duct, including distance between lust turn

and exhaust hood.

TURNS OTHERTHAN 90°

, One turn of 450 or less may be ignored.

, Two 450 turns should be treated us one 900 turn.

, Each turn over 450 should be treated as one 900 turn.

SEALINGOFJOINTS

, Alljoints should be tight to avoid leaks.The mule end of

each section of duct must point away from the dryer.

, Do not assemble the ductwork with fasteners that

extend into the duct. They will serve as a collection

point for lint.

, Duct joints can be made air and moisture-tight by

wrapping the overlapped joints with duct tape.

, Horizontal runs should slope down toward the outdoors

1/4 inch per foot

INSULATION

Duct work that runs through an unheated urea or is

near air conditioning should be insulated to reduce

condensation and lint build-up.

P-JEXHAUST CONNECTION

, WARNING - TO REDUCE THE

RISK OF FIRE OR PERSONAL INJURY:

, This apliancce must be exhausted to the outdoors.

, Use only 4" rigid metal ducting for the home exhaust

duct.

, Use only 4" rigid metal or UL-listed flexible metal

(semi-rigid or foil-type) duct to connect the dryer

to the home exhaust duct. It must be installed

in accordance with the instructions found in

"Connecting The Dryer To House Vent" on page 8 of

this manual.

, Donot terminate exhaust inu chimney, uwall, uceiling,

gas vent, crawl space, attic, under an enclosed floor,

or in any other concealed space of u building. The

accumulated lint could create a potential fire hazard.

, Never terminate the exhaust into a common duct

with u kitchen exhaust system. A combination of

grease and lint creates mpotential fire hazard.

, Do not use duct longer than specified in the exhaust

length table. Longer ducts can accumulate lint,

creating u potential fire hazard.

, Never install u screen in or over the exhaust duct. This

will cause lint to accumulate, creating mpotential fire

hazard.

, Do not assemble ductwork with any fasteners that

extend into the duct. Thesefasteners can accumulate

lint, creating mpotential fire hazard.

, Do not obstruct incoming or exhausted air.

, Provide an access for inspection and cleaning of

the exhaust system, especially at turns and joints.

Exhaust system shall be inspected and cleaned at

least once year.

THIS DRYER COMES READY FOR REAR

EXHAUSTING. IF SPACE IS LIMITED, USE

THE INSTRUCTIONS IN SECTION 9 TO

EXHAUST DIRECTLY FROM THE SIDES OR

BOTTOM OF THE CABINET.

EXTERNALDUCT

OPENING

CSA(AGA}APPROVED

NEWFLEXIBLEGAS For straight line installation, connect

LINECONNECTOR the drger exhaust to the external

exhaust hood using duct tape or

GAS clamp.

INLET

PIPE

DUCTTAPEOR

DUCTCLAMP

4" METALDUCTCUT

TO PROPERLENGTH

DUCTTAPEOR

DUCTCLAMP

Installation Instructions

STANDARD REAR EXHAUST

(Vented above floor level}

ECOMMENDED

ONFIGURATION

O MINIMIZE

XHAUSTBLOCKAGE

ELBOW HIGHLY

RECOMMENDED

NOTE: ELBOWS WILL PREVENT DUCT KINKING AND COLLAPSING

[8]LEVELING AND STABILIZING YOUR

APPLIANCE

_.__E LEVEL

-TO-SIDE

LEVEL

FRONT-TO-BACK.

2LEVELINGLEGS

Level and stabilizing your appliance

1. Carefully move the appliance to its final location.

Gently rock the appliance into position. It is important

not to damage the rubber leveling legs when moving

your appliance to its final location. Damage legs can

increase appliance vibration. It may be helpful to

spray window cleaner on the floor to help move your

appliance to its final position.

Note: do not usewasher cover to lift the unit.

2. To ensure the appliance is level and solid on all four

legs, tilt the appliance forward so the rear legs are off

the ground. Gently set the appliance back down to

allow the rear legs to self adjust.

3.With the appliance in its final position, place a level on

top of back part of the washer lid and check it side to

side, then check front to back. Screw the front leveling

legs up or down to ensure the appliance is resting solid

on all four legs (no rocking or the appliance should

exist), turn the lock nuts on each leg up toward the base

of the unit and snug with a wrench.

Note: Keep the leg extension at minimum to prevent

excessive vibration. The farther out legs are extended, the

more the unit will vibrate.

CONNECTING THE DRYER TO HOUSE

VENT

RIGIDMETALTRANSITIONDUCT

• Forbest drying performance,a rigid metaltransition duct is

recommended.

• Rigidmetal transitions ducts reducethe risk of crushing and

kinking.

UL-LISTEDFLEXIBLEMETAL(SEMI-RIGID)TRANSITIONDUCT

• tf rigidmetal ductcannot beused,thenUL-listedflexiblemetal

(semi-rigid)ductingcan beused(KitWX08X10077).

• Neverinstall flexible metal duct in walls, ceilings,floors or

otherenclosedspaces.

Formanyapplications,installingelbowsat boththedryer and

thewall ishighlyrecommended(seeillustrationson page 9).

Elbowsallowthe dryerto sitcloseto the wallwithout kinking

and or crushing the transition duct, maximizing drying

performance.

Avoidrestingthe duct on sharpobjects.

UL-LISTEDFLEXIBLEMETAL(FOIL-TYPE}TRANSITIONDUCT

• tn specialinstallations,it may be necessaryto connect the

dryerto the housevent usinga flexiblemetal (foiltype)duct.

AUL-listedflexiblemetal (foil-type)ductmay be usedONLYin

installations where rigid metal or flexible metal (semi-rigid)

ducting cannot be usedAND where a 4" diameter can be

maintained throughout the entire length of the transition

duct.

tn Canadaand the United States,onlythe flexiblemetal(foil-

type) ducts that comply with the "Outlinefor ClothesDryer

TransitionDuctSubject2158A"shallbeused.

Total length of flexible metal duct should not exceed 8 feet

(2.4m).

• Avoidrestingthe duct on sharpobjects.

• Forbestdryingperformance:

1.Slideoneendof theduct overtheclothesdryeroutlet pipe.

2.Securetheduct with a clamp.

3.Withthe dryerinits permanentposition,extendthe ductto

its full length.Allow 2"of duct to overlapthe exhaustpipe.

Cutoff and removeexcessduct. Keeptheduct asstraight

aspossiblefor maximumairflow.

/4.Securetheduct to the exhaustpipewith the otherclamp.

Installation instructions

ELBOW HIGHLY

RECOMMENDED

USE

DO NOT _

EXCESSIVE

DON'T

I IIAPPLIANCE

I II°NFLEXIBLE

EXHAUST

[-_ 24" MODELS ONLY:

DRYER EXHAUST TO RIGHT, LEFT OR

BOTTOM CABINET

_WARNING - BEFOREPERFORMING

THIS EXHAUST INSTALLATION, BE SURE

TO DISCON NECTTH EAPPLIANCE FROM

ITS ELECTRICAL SUPPLY. PROTECT

YOUR HANDS AND ARMS FROM SHARP

EDGES WHEN WORKING INSIDE THE

CABINET. BE SURE TO WEAR GLOVES.

For downward venting, rotate elbow

sections so that elbow points downward

REMOVE

DESIRED

KNOCKOUT

(ONLY1)

FLO0

EXHAUST TO LEFT OR RIGHT SIDE OF

CABINET

, Forside ducting, remove the knockout (ONLY1).Rotate

elbow sections so that the opening points to the side.

Preassemble 4" elbow with 4" duct. Use only 4" UL

approved rigid metal for ducting inside the dryer.

, Insert duct assembly through the side opening and

connect to the internal elbow.

WARNING- Be sure not to pullor damage

the electrical wires inside the dryer when inserting the

duct.

4" ULapproved rigid metal

DUCT

TAPE

Apply duct tape as shown on the joint between the dryer

internal duct and the straight duct pipe.

WARNING-

Internal duct joints must be

R secured with tape, otherwise

they may separate and cause

a safety hazard.

27" MODELS ONLY:

DRYER EXHAUST TO RIGHT, LEFT OR

BOTTOM CABINET

WARNING -BEFOREPERFORMING

THIS EXHAUST INSTALLATION, BE SURE

TO DISCON NECTTH EAPPLIANCE FROM

ITS ELECTRICAL SUPPLY. PROTECT

YOUR HANDS AND ARMS FROM SHARP

EDGES WHEN WORKING INSIDE THE

CABINET. BE SURE TO WEAR GLOVES.

For downward venting, rotate elbow

sectionsm, so that elbow points downward.

Installation instructions

EXHAUST TO LEFT OR RIGHT SIDE OF

CABINET

, Rotate elbow sections so that the opening points to the

side to which you want to vent. Preassemble 4" elbow

with 4" duct, Use only 4" UL approved rigid metal for

ducting inside the dryer.

, Connect duct assembly to the internal elbow.

WARNING- Besure not to pull or damage the

electrical wires inside the dryer when inserting the duct.

, Apply duct tape as shown on the joint between the

dryer internal duct and the straight duct pipe.

WARNING-

Internal duct joints must be

H secured with tape, otherwise

they may separate and cause

a safety hazard.

PLUMBING INFORMATION WATER

[ -ISU PPL¥ REQUIREMENTS

, HOTAND COLD WATERFAUCETS- Must be within 42"

of the appliance water inlet hose connections. The

faucets must be 3/4" garden hose-type so inlet hoses

can be connected.

WATER PRESSURE- Must be between 10 and 120

pounds per square inch with a maximum unbalance

pressure, hot vs.cold flowing, of 10pounds per square

inch.

WATERTEMPERATURE- Water heater should be set to

deliver 140° to 150°F (60° to 66°C) in the washer when

HOTwash isselected.

, SHUT-OFFVALVES- Both hot and cold water shut-off

valves (faucets) should be supplied.

LOCATION- Do not install appliance in an area where

the temperature will fall below freezing. If appliance

is stored or transported in freezing temperatures, be

sure all water from the fill and drain systems has been

removed.

DRAIN REQUIREMENTS

, DRAINRATE- The drain or standpipe must be capable

of accepting a discharge at the rate of 16 gallons per

minute.

, DRAINHEIGHT- The drain height must be 33" minimum

and 96" maximum.

, STANDPIPEDIAMETER- The standpipe diameter must

be 1-1/2" minimum. There MUSTbe an air gap around

the drain hose in the standpipe. A snug fit can cause a

siphoning action.

SIPHON BREAKKIT - For a drain facility less than 33"

high, the hose, coupling and clamps provided in the

machine must be used and, in addition, a siphon break

MUST be installed on the back of the machine. Use

Siphon Break Kit WH/49X228 and follow instructions in

the kit.

[ ]CONNECTING TO PLUMBING

FACILITIES

If not installed, install rubber washer in one end of hot water

hose. Thread hot water hose onto connection labeled H at

top rear of washer. Handtighten, plus an additional 1/8 turn

with pliers.

Ifnot installed, install rubber washer in one end of coldwater

hose. Thread cold water hoseonto connection labeled Cat

top rear of washer. Handtighten, plus an additional 1/8 turn

with pliers.

Moveappliance as closeto final location as possible,leaving

room for you to make water, drain, electrical and vent

connections to your home.

NOTE: If longer drain hose

is required, order drain hose

extension kit, GE part number

WH/49X301.Connectadditional

drain hose (contained in kit) to

original hose with hose clamp

(contained in kit).

Insertfreeendofdrain hoseinto

drain opening ofyour home up

to drain hose stopper (do not

removehosestopperitprevents

siphoning). If water valves and

drain are built into wall, fasten

drain hosetooneofwater hoses

with cable tie provided (ribbed

side on inside).If your drains is

a standpipe,fasten drain hose

to standpipe with cable tie

provided.

Installation instructions

_-2]MOBILE OR MANUFACTURED HOME

INSTALLATION

, Installation MUST conform to the MANUFACTURED

HOME CONSTRUCTION & SAFETY STANDARD,

TITLE 24, PART 32-80 or, when such standard is not

applicable, with AMERICAN NATIONAL STANDARD

FORMOBILE HOME,ANSi/NFPA NO. 501B.

, The appliance MUST be vented to the outdoors with

the termination securely fastened to the mobile home

structure.

, Thevent MUSTNOTbe terminated beneath a mobile or

manufactured home.

, Thevent duct material MUSTBEMETAL.

• KIT 14-D346-33 MUSTbe used to attach the appliance

securelyto the structure.

• Thevent MUSTNOTbeconnectedto anyother duct, vent,or

chimney.

, Do not use sheet metal screws or other fastening

devices which extend into the interior of the exhaust

vent.

• Providean opening with a freearea of at least 25 sq.in.for

introductionof outsideair intothedryer room.

ALCOVE OR CLOSET INSTALLATION

, If your appliance isapproved for installation in an alcove

or closet, it will be stated on a label on the appliance

back.

•Thedryer MUSTbevented to theoutdoors.Seethe EXHAUST

INFORMATIONsection.

Donot install this appliance with less than the minimum

clearances shown above.

Thecloset shouldbe vented to the outdoors to prevent gas

pocketingin caseofa gasleakinthe supplyline.

Nootherfuel-burningapplianceshallbeinstalledin thesame

closetwith the appliance.

CONSIDERATION MUST BE GIVEN TO PROVIDE

ADEQUATE CLEARANCES FOR INSTALLATION

AND SERVICE.

, WARNING: DO NOTINSTALLTHIS

APPLIANCE IN A CLOSET WITH A SOLID DOOR.

DOOR VENTILATION OPENING (27"

MODELS)

A minimum of 120 square inches of opening, equally

divided at top and bottom, is required. Air openings are

required to be unobstructed when a door is installed. A

Iouvered door with equivalent air openings for the full

length of the door is acceptable.

27" Model

z: :::n::

Sq.In.

Mli i o%.,n.

When louvers or registers are placed in door openings,

the free air openings of the louvers or registers must

equal 120 square inches.

DOOR VENTILATION OPENING (24"

MODELS)

A minimum of 72 square inches of opening isrequired. Air

openings are required to be unobstructed when a door is

installed. A Iouvered door with equivalent air openings for

the full length of the door is acceptable.

24" Model

/o/

H II J'ii'J;4 Sq. In.

I'l HT

When louvers or registers are placed in door openings,

the free air openings of the louvers or registers must

equal 72 square inches.

[Z4]BATHROOM OR BEDROOM INSTALLATION

, The appliance MUST be vented to the outdoors. See

EXHAUSTINFORMATIONsection 6 & 7.

, The installation must conform with local codes or,

in the absence of local codes, with the NATIONAL

ELECTRICALCODE,ANSI/NFPA NO. 70 and NATIONAL

FUELGASCODE,ANSIZ223.

Installation instructions

SERVICING

ILWARNING- LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING

CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION

AFTER SERVICING/INSTALLATION.

Forreplacement parts and other information, refer to Owner's Manual for servicing phone numbers.

REGISTERYOUR NEW APPLIANCE TO RECEIVEANY

IIvlPORTANTPRODUCT NOTIFICATIONS.

Please go to www.GEAppliances.com or mail in your

Product Registration Card.

For questions on installation, call: 800.626.2000 (US)or

800-561-3344 (Canada).

Page is loading ...

Instructions d'Installation

ALIMENTATION DE GAZ

. Un rouleau adh6sif pour branchement a gaz de 1/8 in.,

accessible pour des tests de calibrage du branchement,

doit _tre install6 immadiatement en amont du

branchement d'alimentation en gaz _ la s@cheuse.

Contactez I'entreprise de gaz la plus proche si vous avez

des questions sur I'installation du rouleau adh@sif pour

prise.

. Le branchement d'alimentation doit _tre un tuyau

rigide de 1/2in. et 6quip6 avec une valve de fermeture

accessible a 6 ft. de distance, et dans la m_me piece

que la s_cheuse.

Utilisez le compos6 pour tuyau ou le scotch Taflon

appropri_ pour le gaz naturel et LR

Vous devez utiliser avec cette s@cheuse un

branchement flexible en matal list6 comme

branchement ANSI Z21.24 / CSA6.!0. La Iongueur de

ce branchement ne devrait pas excader 3 ft.

Connectez le branchement flexible en matal 5 la

sacheuse et (3I'alimentation en gaz.

Ouvrez la valve de fermeture.

REBRANCHER LE GAZ

Branchement list6 ANSI Z2!.24 / CSA 6.10

24"

BRANCHEMENT

NEUF FLEXIBLE A,

GAZ EN METAL ENTREEA GAZ

DE LA SECHEUSE

RETOUR DE

L'APPAREIL

24" & 27"

FLARE

NPT ENTREE

DE L'APPAREIL 27"

SEULEMENT

45 ° COUDE

27" SEULEMENT

ADAPTATEUR

27" SEULEMENT

BRANCHEMENT NEUF

FLEXIBLE A GAZ EN

METAL

ADAPTATEUR

J NPT

1/8" POUR VERIFIER

LA PRESSION DU GAZ A

ENTRANT

VALVE DE FERMETURE

TAILLE DU BRANCHEMENT D'AU

MOINS 1/2"

PLANCHER

N'EST PAS FOURNI

Note: Le connecteur et les raccords sont congus pour 6tre

utilisas uniquement sur I'installation d'origine et ne doivent

pas 6tre rautilisas pour un autre appareil ou a un autre endroit.

Gardez fusae fin de I'adaptateur sans graisse, huile et un produit

d'6tanch6it6.

ATTENTION:Utiliser des adaptateurs, comme i!lustr@. Ecrous

connecteur dolt ne pas 6tre connect6 directement (]filetages.

27"

APPLIQUEZLECOMPOSED'

ETANCHEtTEDESTUYAUTERIESA

L'ADAPTATEURETLEENTREEDUGAZ

DELA SECHEUSE

SERRERLA LIGNE DE BRANCHEMENT A

GAZ FLEXIBLE A L'ENTREEA GAZDE LA

SECHEUSE EN UTILISANT 2 CLES/_MOLETTE

24"

/_ APPLIQUEZ LECOMPOSE

D' ETANCHEITE DES

TUYAUTERIES A L' ENTREEA

GAZ DE LA SECHEUSE

24"

SERRERLA LIGNE DE

BRANCHEMENT A GAZ

FLEXIBLE A L'ENTREE A GAZ DE

LA SECHEUSE EN UTILISANT 2

CLES/_ MOLETTE

24" & 27"

APPLIQUEZ LE

COMPOSED' ETANCHEITE

DESTUYAUTERIES

SURTOUS LES FILETS

DESPARTIESM/_LE

24" & 27"

SERRER TOUS LES CONNECTEURS EN UTILISANT

2 CLt]S A MOLETTE. NE PAS SUR-SERREZ PAS LES

CONNECTEURS DE GAZ.

Page is loading ...

Instructions d'Installation

i_-IREPARATION

AVERTISSEMENT - MARQUEZ TOUSLES FILS AVANT LE DEBRANCHEMENT

LORSQUE VOUS EFFECTUEZ UN CONTROLE POUR REPARATION. LES ERREURS DE

BRANCHEMENT PEUVENT CAUSEES DES PROBLEMES DE FONCTIONEMENT APRES

REPARATION ET D'INSTALLATION.

Pour les pisces de rech(]nge et (]utres inform(]tions, veuillez reporter (]u Manuel de I'Utilis(]teur pour les num6ros de

t616phone du service (]prOsvente.

ENREGISTREZVOTRE NOUVEL APPAREIL POUR q)UE

VOUS RECEVIEZ DESINFORMATIONS IMPORTANTES

SUR LE PRODUIT.

Allez, SVP,sur notre site www.GffAppliances.com ou

envoyez par la poste votre Carte d'inscription du produit.

Pour des questions sur I'inst(]ll(]tion, composez:

800.626.2000 (E.U.)ou 800.56!.334/4 (CGnGdG)

Page is loading ...

GE GTUN275EM0WW Installation guide

Brand: GE

Model: GTUN275EM0WW

Category: Washing machines

Type: Installation guide

Download PDF

report

in other languages

français: GE GTUN275EM0WW Guide d'installation
español: GE GTUN275EM0WW Guía de instalación

GE GTUN275EM0WW Installation guide

GE GTUN275EM0WW Installation guide

in other languages

Related papers

Other documents