Ferm SSM1004 Owner's manual

Brand: Ferm

Model: SSM1004

Category: Power tools

Type: Owner's manual

This manual is also suitable for

Page is loading ...

Product: Ferm Scroll saw machine.

Type FZ-40/16, articlenumber 430017;

Type FZ-13/330, articlenumber 430070.

Ferm Genemuiden, The Netherlands

Sound pressure level 60 dB(A)

Vibration (

) 1,8 m/s

CAREFULLY READ THE INSTRUCTIONS

BEFORE YOU USE THE SCROLL SAW

MACHINE!

1. GENERAL SAFETY RULES

Keep the work area clean.

- A cluttered work area may cause accidents.

- Make sure the work area is well lit.

Work environment.

Never leave tools in the rain. Do not use tools in

damp or wet places and always provide adequate

lighting. Never use tools near inflammable liquids

or gasses.

Prevent electrical shock.

Keep the power cord away from heat, oil and

sharp edges. Avoid skin contact with exposed

parts of the power cord, plug and earthed objects,

such as metal pipes, radiators, central heating boi-

lers, refrigerators. etc.

Keep children away.

Never allow children or spectators to touch the tools,

keep them at a safe distance from the work area.

Store tools in a safe place.

Tools that are not used must be stored in a dry and

locked placed, out of the reach of children.

Do not force the tool.

The machine will do the job better and safer at the

rate for which it was intended. Damage caused by

forcing the tool is not covered by the warranty.

Use the right type of tool.

Do not use low powered tools for heavy duty ope-

rations. Never use the machine other than for its

intended purpose.

Wear suitable clothing.

- Do not wear loose clothing or jewellery that might

get caught in moving parts.

- Never wear rings with protruding parts;

- Cover long hair;

Wear safety glasses.

Wear a mask when the work is dusty.

Cable.

Never carry the tool by its cable and do not tug at

the cable to pull the plug from the socket. Keep the

cable away from heat, oil and sharp edges.

Always clamp the work.

Always clamp the work against the tool rest.

Never grind objects that are too small to hold.

Posture.

Do not overreach. Be sure of your footing and

balance at all times.

Maintain the tool with care.

The tool works best and safest if it is kept clean.

Observe the instructions for maintenance and

changing accessories. Keep the tool dry and free

from oil and grease.

Disconnect the machine.

Disconnect the machine when you do not use it,

before cleaning and when changing accessories and

tools.

Remove wrenches from the machine.

Before starting the machine, make sure to remove

wrenches and other tools.

Avoid unintentional starting.

Never carry the plugged in machine with your fin-

ger on the switch. Make sure the switch is off when

the machine is plugged in.

Extension cable for outdoor use.

When working outdoors use only extension cables

suitable for this purpose and marked as such.

2 Ferm

ART.NR

TYPE

45°

VOLT/HZ WATT RPM MM MM MM MM (L xW)

430017 FZ-40/16 230V~/50Hz 110 1.440 25 50 405 365 x 200

430070 FZ-13/330 230V~/50Hz 110 1.335 25 50 330 300 x 170

Ferm

0 - 45

Only in case of guarantee claim, send this card to:

Diese Karte nur bei Garantie Anspruch senden zu:

Alleen ingeval van een garantieclaim deze kaart opsturen naar:

Soulement en cas réagir de garantie envoyez ce carte par:

Solamente en caso de la reclamación enviar esta carta para:

Só no caso de querer fazer uso da garantia enviar este certificado par:

ªﬁÓÔ ÛÂ ÂÚ›ÙˆÛË ··›ÙËÛË˜ ‚¿ÛÂÈ ÙË˜ ÂÁÁ‡ËÛË˜ ÌÔÚÂ›ÙÂ Ó·

Ù·¯˘‰ÚÔÌ‹ÛÂÙÂ ÙÔ ÎÔ˘ﬁÓÈ ·˘Ùﬁ ÛÙË ‰ÈÂ‡ı˘ÓÛË:

24 MONTHS GUARANTEE CERTIFICATE • 24 MONATE GARANTIE-

SCHEIN • 24 MAANDEN GARANTIEKAART • 24 MOIS CERTIFICAT DE

GARANTIE • 24 MESES CARTA DE GARANTIA • CERTIFICADO DE

GARANTIA DE 24 MESES • ∫√À¶√¡π ∂°°À∏™∏™ 24 ª∏¡ø¡

Stamp dealer:

Stempel Händler:

Stempel handelaar:

Timbre marchand:

Sello del vendedor:

Carimbo

do comerciante:

AÓÙÈÚÔÛÒÔ˘:

Nr. Article/Artikel Nr./Artikelnr./N° d’Article/

N° de articulo/N

. do artigo/AÚ. ÚÔ˚ﬁÓÙÔ˜:

Article/Artikel/Artikel/Article/

Artigo/Articulo/

¶ÚÔ˚ﬁÓ:

Date of purchase/Kaufdatum/Koopdatum/Date d’achet/

Fecha de compra//Data da compra/

∏ÌÂÚÔÌËÓ›· ·ÁÔÚ¿˜:

Owner/Eigentümer/Eigenaar/Propriétaire/

Propietario/Propietário/

π‰ÈÔÎÙ‹ÙË˜:

Address/Adresse/Adres/Adresse/

Endereço/Dirección/

¢ÈÂ‡ı˘ÓÛË:

Place/Ort/Plaats/Ville/

Domicilio/Lugar/

¶ﬁÏË:

Country/Land/Land/

Pays/Pais/Pais/

ÃÒÚ·:

Signature/Unterschrift/Handtekening/

Signature/Firma/Assinatura/

ÀÔÁÚ·Ê‹:

SERVOTOOL

POSTBUS 105

8280 AC GENE-

MUIDEN

HOLLAND

Stay alert.

Watch what you are doing, use your common sen-

se, do not operate the tool when you cannot keep

your mind on the job.

Check the machine for damage.

- Before starting the machine, check that all safety

devices and damaged parts operate smoothly and

efficiently.

- Make sure all moving parts are in good working

order; check the machine for any broken or jam-

ming parts, make sure all parts are fitted properly

and any other conditions that might affect the

functioning of the machine are favourable.

- If not stated otherwise in this manual, damaged safety

devices and machine parts must be repaired or

replaced by a recognized service centre. Damaged

switches must be replaced by a service centre. Do not

use the machine when it cannot be switched on or off.

Have your tool repaired by an expert!

This electric appliance is in accordance with the

relevant safety rules. Repairing of electric applian-

ces may be carried out only by experts other wise

it may cause considerable danger for the user.

For your own safety use only accessories

and attachments recommended in this

manual or the catalogue. The use of

other than the stated accessories or

attachments may cause injuries.

2. SPECIFIC SAFETY RULES

BEFORE USING THE MACHINE:

1. The following points need to be checked:

- do the voltage of the machine correspond to

the mains voltage (appliances for a mains volta-

ge of 230 V~ can be connected to a mains volta-

ge of 220 V~ without any problems);

- an earthed mains connection needs always to

be used;

- are the mains lead and the mains plug in a good

condition: solid, without any loose ends or

damage;

2. The machine must stand firm on a flat, solid surface.

3. Never press against the sides of the blade because

it can break.

4. Watch out while sawing wood. Nails and knots can

make the wood strike back from the machine

5. Never let the machine work unattended.

6. The teeth of the blade must point downward.

WHILE USING THE MACHINE:

1. Do not use extension cables which are too long.

2. Rests of wood may never be taken away by hand whi-

le the machine is running. First turn the machine off.

3. The sawblade is the most important piece in the

saw machine. Make sure it has no ripped of teeth,

and it is crackfree.

IMMEDIATELY SWITCH OFF THE MACHI-

NE IN CASE OF:

1. defective mains plug, mains line or damage to the

mains line;

2. defective switch;

3. smoke or bad smell caused by scorched insulation.

3. GUARANTEE PROVISIONS

1. Ferm guarantees all material and construction

defects for a period of 24 MONTHS after pur-

chase. Other claims in respect of damage, of wha-

tever nature, direct or indirect, to persons and/or

materials are excluded.

2. Always consult your Ferm dealer in the first

instance. Usually he will be able to solve the pro-

blem or repair the defect.

3. If parts are repaired or replaced within the warranty

period, this does not extend the warranty period.

4. Fair wear and tear is not covered by this warranty.

For example motors, switches or bulbs.

5. THIS WARRANTY APPLIES ONLY:

- if you can submit proof of the date of purchase,

i.e. a RECEIPT stating the date of purchase;

- if you have completed and signed the enclosed

warranty card (in the back of this manual);

- if no repairs or alterations have been made to

the machine by third parties, nor other than

the original parts have been fitted;

- if the machine was used in accordance with the

instructions;

- if we cannot plead force majeure.

6. The warranty provisions apply in combination

with our terms of delivery and sale.

7. All cost of transport of the machine to be repaired

ar at buyer’s expense. Badly packed articles are

not accepted.

4. ENVIRONMENTAL PROTECTION

Recycling raw materials is preferable to dumping them

as waste. To prevent the machine from being damaged

during transport its packing must be strong. Insofar as

possible the packing consists of recyclable materials

such as paper, cardboard and wood.

5. FERM'S AFTER SALES SERVICE

Save the original packing. Should you ever have to

move the machine there is less risk of damage in the

original packing. In the case of a warranty claim the

machine can best be returned in the original packing.

Should your machine ever become defective, please

consult your local Ferm dealer.

6. ASSEMBLY INSTRUCTION

Place the machine on a sturdy bench and be sure it is

properly levelled.

Ferm 3

26 Ferm

EC-EXPLANATION OF AGREEMENT • EG-ERÖRTERUNG VON

ÜBEREINSTIMMUNG • EG-VERKLARING VAN OVEREEN-

STEMMING • CERTIFICAT DE CONFORMITE-CE • CERTIFICA-

CIÓN DE CONFORMIDAD-CE • DECLARAÇAO DE ACORDO

DA CE •

¢∏§ø™∏ ¶π™∆√∆∏∆A™ ∂∫

Undersigned,/ Unterzeichnete,/ Ondergetekende,/ Soussigné,/ Signatario,/ O abalxo assinado/ √ ˘ÔÁÂÁÚ·ÌÌ¤ÓÔ˜,

POSTBUS 134

8280 AC GENEMUIDEN

NEDERLAND

- Declares that with this the, / Erklärt daß mit dieser die, / Verklaart hiermee dat de, / Déclare que,/ Declarar

qué/ Declara que/ ªÂ ÙËÓ ·ÚÔ‡Û· ‰‹ÏˆÛË ÈÛÙÔÔÈÂ› ﬁÙÈ Ù· ÚÔ˚ﬁÓÙ·:

FERM FZ-40/16, ART.NR. 430017

FERM FZ-13/330, ART.NR. 430070

- are in conformity with the regulations of the machine guide-lines; /die Bestimmungen der Maschinerichtlinie

entsprechen; / voldoen aan de bepalingen van de machinerichtlijn; / sont conformes aux dispositions de la direc-

tive-machine; /reunir las disposición de linea à máquina/ satisfazem as determinações respeitantes às directivas

sobre máquinas/ ·ÓÙ·ÔÎÚ›ÓÔÓÙ·È ÛÙÈ˜ ‰È·Ù¿ÍÂÈ˜ ÙË˜ √‰ËÁ›·˜ ÂÚ› ªË¯·ÓÒÓ:

MACHINE GUIDE-LINE

89/392/EEG, 91/368/EEG, 93/44/EEG, 93/68/EEG

- are in conformity with the regulations of the next EC-guide-lines; / die Bestimmungen der folgenden EG-Richtli-

nien entsprechen; / voldoen aan de bepalingen van de volgende EG-richtlijnen; / sont conformes aux dispositions

des directives-CE suivantes: /reunir las disposición de linea-CE siguiente/ satisfazem as determinações respeitan-

tes às sequintes directivas da CE;/ ·ÓÙ·ÔÎÚ›ÓÔÓÙ·È ÛÙ· ·ÎﬁÏÔ˘ı· ÚﬁÙ˘·

EMC GUIDE-LINE

89/336/EEG, 92/31/EEG

LOW VOLTAGE GUIDE-LINE

73/23/EEG

- are in conformity with the following standards: / die folgenden Normen entsprechen: / voldoen aan de volgende

normen: / sont conformes aux normes suivantes /satisfacer las normas siguiente;/ satisfazem as sequintes nor-

mas;/ ·ÓÙ·ÔÎÚ›ÓÔÓÙ·È ÛÙ· ·ÎﬁÏÔ˘ı· ÚﬁÙ˘·:

EN 61029-1

EN 55014

EN 60555-2

Done at/Geschehen in/Gedaan te/Dressé à/

Huego en/ Feito en/ ™˘ÓÙ¿¯ıËÎÂ ÛÙÔ on/am/op/le/à/a/ÛÙÈ˜

GENEMUIDEN, THE NETHERLANDS 23-01-1996

G.M. ENSING

Quality department

INSTALLING THE BLADE

Always remember to disconnect the machi-

ne from the power source to avoid injury

before installing the blade.

1. Select the correct blade according to the wood

material to be cut.

2. Loosen the blade tension knob.

3. To install the blade, insert the blade with the teeth

pointing downward through the table slot until the

blade pin (or saw-blade adaptor) can be hooked by

the bottom blade holder.

4. Pull upward so that the blade pin (or saw-blade

adaptor) can be hooked by the top blade holder.

5. Tighten the blade tension knob until the proper

tension is obtained.

6. Remove all tools or objects from the blade area.

7. Turn the power on and allow the blade to run, before

actual cutting operation is performed. Check that the

blade runs smoothly.

With type FZ-40/16 two saw blade adaptors are

supplied. These saw-blade adaptors can be used

for saw blades intended for fretsaws.

- Fix the saw blade adaptors to the saw blade (inten-

ded for fretsaw). Be sure that the internal wrench

bolts are screwed both the same amount, so that

the saw blade will not be installed wrong and

would result in a not so accurate sawing job.

- Place the whole thing in blade holder, see “Instal-

ling the blade”.

NOTE: In the event of blade breakage, replacement

should be performed as instructed above.

7. TILTING TABLE

The table on this scroll saw may be tilted 45° maxi-

mum. To tilt the table, follow these instructions:

1. Loosen the table tilt fixing lever located under the

table;

2. Tilt the table with your hand to the angle required;

3. A graduated scale is provided for indicating the

table angle degree;

4. Tighten the table tilt locking lever.

8. BASIC OPERATING INSTRUCTIONS

1. The scroll sawblade cuts on its downward stroke.

2. Feed the workpiece slowly with a minimum of

pressure and smoothly towards the sawblade.

3. Care should be taken to hold the workpiece firmly

against the table with your hands and feed the

workpiece slowly to prevent the blade from ben-

ding or twisting.

4. Always keep the blade sharp for best cutting result.

5. Use correct blade size. Selection of blade depends

on the wood material and the curve to be cut. In

general, the thinner and harde the wood material,

the finer the blade teeth. Narrow blades should be

selected for cutting sharp curves.

9. REMOVING THE BLADE

Always remember to disconnect the machine

from the power source to avoid injury before

removing the blade.

1. Loosen the blade tension knob until the spring is

completely released.

2. Slightly depress the top blade holder and slightly

lift the blade upward to facilitate removing the bla-

de from the holder.

3. Slightly lower and move the blade forward to free

it from the bottom blade holder.

4. Remove the blade by pulling it upward.

10. MAINTENANCE

While maintaining and cleaning the sawma-

chine pull the plug from the mainssocket.

Never use water or other agressive liquids whi-

le cleaning electrical parts of the machine.

PERIODIC MAINTENANCE OF THE MACHINE

WILL PREVENT UNNECESSARY PROBLEMS!

- Keep the sawingtable clean to maintain accuracy

while sawing.

- Keep the outside of the machine clean so all parts can

move freely and without any wear to all the parts.

11. MALFUNCTIONS

Below we have listed a number of possible causes and

corresponding solutions in case the machine does not

function as it should:

1. The engine overheats above 70° Celsius.

The engine is overloaded:

- Start to slow down the sawing so the engine can cool off.

The engine has a defect:

- Contact your local Ferm dealer to have the tool

inspected and/or repaired.

2. The machine stops immediately after swit-

ching on.

Interruption in the electric circuit:

- Check the circuit (of the mains voltage).

Defective switch:

- Contact your local Ferm dealer to have the tool

4 Ferm

Ferm 25

AVAILABLE SPARE PARTS FOR FZ-40/16

REF.NR. DESCRIPTION FERM NR.

4 TRANSPARANT COVER FOR SAW 209561

5 HEX. HD. BOLT 209575

7 NUT 209562

8 BASE 209563

11 KNOB 209564

13 SCALE DIVISION PLATE 209565

15 TABLE 209566

23 MOTOR 209567

27 RUBBER DUSTCAP 209568

28 BEARING BUSH 209569

29 KNOB 209570

33 BALANCER 209571

35 SET SCREW 209572

36 SPRING 209573

39 BLADE HOLDER (UPPER) 209574

49 BALL BEARING 625 ZZ 800625

50 HOLDER FOR BEARING 209576

52 ARM 209577

54 BLADE HOLDER (LOWER) 209578

- CASE FOR SWITCH 209557

- SWITCH 209558

- COOLING FIN FOR MOTOR 209613

- COVER FOR COOLING FIN 209614

- CONDENSATOR 3UF/400VAC 209615

Page is loading ...

Ferm SSM1004 Owner's manual

Brand: Ferm

Model: SSM1004

Category: Power tools

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

français: Ferm SSM1004 Le manuel du propriétaire
español: Ferm SSM1004 El manual del propietario
Deutsch: Ferm SSM1004 Bedienungsanleitung
Nederlands: Ferm SSM1004 de handleiding

Ferm SSM1004 Owner's manual

This manual is also suitable for

Ferm SSM1004 Owner's manual

in other languages

Related papers

Other documents