VIRTUFIT VF06007 User manual

@virtufit_fitness

VirtuFit

www.virtufit.com

USER MANUAL

Basketball Hoop

VF06007

SERIAL NUMBER

SERIENNUMMER

SERIENUMMER

NUMERO DE SERIE

USER MANUAL

02

TOOLKIT

# DESCRIPTION QTY

A Blackboard 1

B Backing Plate 1

C Short bolt 2

D Hoop 1

E Nut (big: 4pcs, small: 4pcs) 8

F Washer (big: 4pcs, small: 4pcs 8

G Bolt 4

H Bracket 1

I Clamp 2

J Long Bolt 4

K Net 1

L Supporting Tube 1

M Spanner 2

N Pump 1

P Basketball 1

NOTE!

Lay out all the parts.

LET OP!

Haal alle onderdelen uit de verpakking en leg ze op de grond.

HINWEIS!

Legen Sie alle Teile aus.

REMARQUE!

Disposez toutes les pièces.

USER MANUAL

03

STEP 01

STEP 02

澳

1. Lay out all the parts. Figures (1) and (2).

Fig (1) Fig (2)

2. Locate the backing plate (1 x part B) and two short bolts (2 x part C), Figures (3) and (4). Attach the backing

plate using the middle holes to the backboard using the bolts supplied. Figures (5) and (6)

Fig (3) Fig (4)

澳

澳澳澳

Fig (5) Fig (6)

澳

1. Lay out all the parts. Figures (1) and (2).

Fig (1) Fig (2)

2. Locate the backing plate (1 x part B) and two short bolts (2 x part C), Figures (3) and (4). Attach the backing

plate using the middle holes to the backboard using the bolts supplied. Figures (5) and (6)

Fig (3) Fig (4)

澳

澳澳澳

Fig (5) Fig (6)

澳

1. Lay out all the parts. Figures (1) and (2).

Fig (1) Fig (2)

2. Locate the backing plate (1 x part B) and two short bolts (2 x part C), Figures (3) and (4). Attach the backing

plate using the middle holes to the backboard using the bolts supplied. Figures (5) and (6)

Fig (3) Fig (4)

澳

澳澳澳

Fig (5) Fig (6)

USER MANUAL

04

STEP 03

澳

3. Take the hoop (1 x part D), small nuts (4 x part E), small washers (4 x part F), bolts (4 x part G) and bracket

(1 x part H) Fig (7) and (8). Attach the hoop to the backboard using the bolts and bracket as shown in Fig (9)

and (10).

Note: Ensure the bracket is fitted the correct way up (largest section down) to allow the hoop to swing

upwards against the backboard as in Fig (10).

澳澳澳

Fig (7) Fig (8)

Fig (9) Fig (10)

澳

3. Take the hoop (1 x part D), small nuts (4 x part E), small washers (4 x part F), bolts (4 x part G) and bracket

(1 x part H) Fig (7) and (8). Attach the hoop to the backboard using the bolts and bracket as shown in Fig (9)

and (10).

Note: Ensure the bracket is fitted the correct way up (largest section down) to allow the hoop to swing

upwards against the backboard as in Fig (10).

澳澳澳

Fig (7) Fig (8)

Fig (9) Fig (10)

STEP 04

澳

4. Insert the bolts from the front side of backboard, then tighten the small nut and small washer onto the back of

each bolt by using the spanner as shown in images. Fig (11) and (14)

澳澳

Fig (11) Fig (12) 澳

澳澳澳

Fig (13) Fig (14)

澳

4. Insert the bolts from the front side of backboard, then tighten the small nut and small washer onto the back of

each bolt by using the spanner as shown in images. Fig (11) and (14)

澳澳

Fig (11) Fig (12) 澳

澳澳澳

Fig (13) Fig (14)

USER MANUAL

05

USER MANUAL

VF06051 & VF06003 - STEP 5 TO 10

VF06004 & VF06015 - STEP 11 TO 15

VF06051

VF06004

VF06003

VF06015

NOTE!

If your trampoline model is VF06051 or VF06003, please continue to install from step 5 to step 10.

NOTE!

If your trampoline model is VF06004 or VF06015, please continue to install from step 11 to step 15.

USER MANUAL

06

USER MANUAL

STEP 05 - VF06051 & VF06003

STEP 06

STEP 07

澳

5. Locate clamp (2 x part I), big washers (4 x part F), long bolts (4 x part J), big nuts (4 x part E) and

supporting tube (1 x part L) Fig (15)

Fig (15)

6. Position the supporting tube on the assembled backboard with clamps.

Note: Please note that the welded tube on the supporting tube must be face down as per Fig (17)

澳澳澳

Fig (16) Fig (17)

7. Fix the long bolts with big nuts and big washers into the screw holes on the clamps as per Fig (18) (19) then

tighten with the spanner Fig (20).

Fig (18) Fig (19)澳

澳

5. Locate clamp (2 x part I), big washers (4 x part F), long bolts (4 x part J), big nuts (4 x part E) and

supporting tube (1 x part L) Fig (15)

Fig (15)

6. Position the supporting tube on the assembled backboard with clamps.

Note: Please note that the welded tube on the supporting tube must be face down as per Fig (17)

澳澳澳

Fig (16) Fig (17)

7. Fix the long bolts with big nuts and big washers into the screw holes on the clamps as per Fig (18) (19) then

tighten with the spanner Fig (20).

Fig (18) Fig (19)澳

澳

5. Locate clamp (2 x part I), big washers (4 x part F), long bolts (4 x part J), big nuts (4 x part E) and

supporting tube (1 x part L) Fig (15)

Fig (15)

6. Position the supporting tube on the assembled backboard with clamps.

Note: Please note that the welded tube on the supporting tube must be face down as per Fig (17)

澳澳澳

Fig (16) Fig (17)

7. Fix the long bolts with big nuts and big washers into the screw holes on the clamps as per Fig (18) (19) then

tighten with the spanner Fig (20).

Fig (18) Fig (19)澳

USER MANUAL

07

USER MANUAL

STEP 08

STEP 09

澳

Fig (20) Fig (21)澳

澳

8. Attach the net (1 x part K) to the hoop using the Velcro on the net. Fig (22).

Fig (22)

9. Select the enclosure pole you wish to position the Basketball Hoop, and then take off the T Cap from

the fiberglass rods. Attach the assembled backboard to the top of upper pole tube by inserting the

welded tube onto the supporting tube into the top of the enclosure pole tube as per Figures (23) and

(24).

澳

Fig (23) Fig (24)

澳

Fig (20) Fig (21)澳

澳

8. Attach the net (1 x part K) to the hoop using the Velcro on the net. Fig (22).

Fig (22)

9. Select the enclosure pole you wish to position the Basketball Hoop, and then take off the T Cap from

the fiberglass rods. Attach the assembled backboard to the top of upper pole tube by inserting the

welded tube onto the supporting tube into the top of the enclosure pole tube as per Figures (23) and

(24).

澳

Fig (23) Fig (24)

澳

Fig (20) Fig (21)澳

澳

8. Attach the net (1 x part K) to the hoop using the Velcro on the net. Fig (22).

Fig (22)

9. Select the enclosure pole you wish to position the Basketball Hoop, and then take off the T Cap from

the fiberglass rods. Attach the assembled backboard to the top of upper pole tube by inserting the

welded tube onto the supporting tube into the top of the enclosure pole tube as per Figures (23) and

(24).

澳

Fig (23) Fig (24)

USER MANUAL

08

USER MANUAL

STEP 10

澳

10. For the T cap model once the basketball set is attached reinsert the T cap to the top of the enclosure

pole. 澳

澳澳澳澳澳

Fig (25) Fig (26)澳

澳

澳澳澳澳

澳

Now, your basketball hoop is almost finish!!!

澳

If your trampoline model is VF06051 or VF06003 model,

please continue to install from step 5 to step 10.

澳澳澳澳

VF06051 VF06003

If your trampoline model is VF06015 or VF06004 model,

please continue to install from step 11 to step 15.

澳澳澳澳澳

VF06004 VF06015

VF06051 VF06003

USER MANUAL

09

USER MANUAL

STEP 11 - VF06004 & VF06015

STEP 12

STEP 13

澳

Step 11 to step 15 is for VF06015 or VF06004 model, please

continue from step 4.

澳澳澳澳澳

11. Locate clamp (2 x part I), big washers (4 x part F), long bolts (4 x part J), big nuts (4 x part E) Fig (27)

Fig (27)

12. Position the assembled backboard on the inside of the safety net at the pole furthest away from the

entrance, e.g. the opposite side to the entrance. With the assistance of a second person, hold the bottom of

the backboard at the top of the safety net pole as shown in Fig (28). The fixing bracket should be around

5cm from the top of the safety net. Locate the four screw holes and using a pair of scissors, carefully snip

one strand at each screw location to allow easy fitment. Refer to Fig (28).

Fig (28)

13. Fix the long bolts with big nuts and big washers into the screw holes on the clamps as per Fig (29) then

tighten with the spanner. The padding will compress as you tighten the screws. Adequately fasten until the

backboard is firmly positioned.

Fig (29)

澳

Step 11 to step 15 is for VF06015 or VF06004 model, please

continue from step 4.

澳澳澳澳澳

11. Locate clamp (2 x part I), big washers (4 x part F), long bolts (4 x part J), big nuts (4 x part E) Fig (27)

Fig (27)

12. Position the assembled backboard on the inside of the safety net at the pole furthest away from the

entrance, e.g. the opposite side to the entrance. With the assistance of a second person, hold the bottom of

the backboard at the top of the safety net pole as shown in Fig (28). The fixing bracket should be around

5cm from the top of the safety net. Locate the four screw holes and using a pair of scissors, carefully snip

one strand at each screw location to allow easy fitment. Refer to Fig (28).

Fig (28)

13. Fix the long bolts with big nuts and big washers into the screw holes on the clamps as per Fig (29) then

tighten with the spanner. The padding will compress as you tighten the screws. Adequately fasten until the

backboard is firmly positioned.

Fig (29)

澳

Step 11 to step 15 is for VF06015 or VF06004 model, please

continue from step 4.

澳澳澳澳澳

11. Locate clamp (2 x part I), big washers (4 x part F), long bolts (4 x part J), big nuts (4 x part E) Fig (27)

Fig (27)

12. Position the assembled backboard on the inside of the safety net at the pole furthest away from the

entrance, e.g. the opposite side to the entrance. With the assistance of a second person, hold the bottom of

the backboard at the top of the safety net pole as shown in Fig (28). The fixing bracket should be around

5cm from the top of the safety net. Locate the four screw holes and using a pair of scissors, carefully snip

one strand at each screw location to allow easy fitment. Refer to Fig (28).

Fig (28)

13. Fix the long bolts with big nuts and big washers into the screw holes on the clamps as per Fig (29) then

tighten with the spanner. The padding will compress as you tighten the screws. Adequately fasten until the

backboard is firmly positioned.

Fig (29)

USER MANUAL

10

USER MANUAL

STEP 14

STEP 15

澳

14. Double check all screws and fittings have been tightened. Refer to Fig (30)

Fig (30)

15. Attach the net (1 x part K) to the hoop using the Velcro on the net. Fig (31).

Fig (31)

澳

澳澳澳澳澳

Now, your basketball hoop is almost finish!!!

澳

14. Double check all screws and fittings have been tightened. Refer to Fig (30)

Fig (30)

15. Attach the net (1 x part K) to the hoop using the Velcro on the net. Fig (31).

Fig (31)

澳

澳澳澳澳澳

Now, your basketball hoop is almost finish!!!

澳

If your trampoline model is VF06051 or VF06003 model,

please continue to install from step 5 to step 10.

澳澳澳澳

VF06051 VF06003

If your trampoline model is VF06015 or VF06004 model,

please continue to install from step 11 to step 15.

澳澳澳澳澳

VF06004 VF06015

USER MANUAL

11

USER MANUAL

TO INFLATE THE BASKETBALL

澳

To inflate the basketball:

16. Locate the needle for the pump and attach it to the pump, pump air into the basketball.

澳

澳澳澳澳

Now, have fun with your basketball hoop!!!

Please remember, DO NOT hang from the basketball set.

VIRTUFIT

Twekkelerweg 263

7553 LZ Hengelo

The Netherlands

info@virtufit.nl

VIRTUFIT VF06007 User manual

Related papers

Other documents