Jones Platinum Strength Training System
OWNER'S MANUAL
MA9059A Recreation Supply Inc.
Model No. JP1000.1
BODYCRAFT is a division of Recreation Supply
7699 Green Meadows Drive
Lewis Center, OH 43035
1
BEFORE YOU BEGIN
Congratulations and thank you for selecting the JONES PLATINUM strength
training system. The JONES PLATINUM offers an impressive array of
strength training exercises to develop every major muscle group of the body.
Whether your goal is cardiovascular fitness, a shapely, toned body or dramatic
muscle size and strength, the JONES PLATINUM will help you achieve the
specific results you want.
For your safety and benefit, read this manual and the accompanying literature
before using the JONES PLATINUM. Keep this manual for future reference.
If you have additional questions, please call your local dealer or our customer
service department at 800-990-5556 Monday through Friday, 9 a.m. until 5 p.m.
Eastern Time.
IMPORTANT SAFETY NOTES
1. This product must be assembled on a flat, level surface to assure its
proper function.
2. Clean frame on a regular basis. We recommend warm,
soapy water. Do not use harsh or abrasive chemicals.
3. Inspect and tighten all parts before every use. Replace any worn
parts immediately. Failure to do so may result in serious injury.
4. Keep children away from the JONES PLATINUM at all times.
5. Always use the safety spotters! Failure to do so could result in
serious injury, or death.
6. Be certain bar hooks are fully engaged before releasing your grip!
Failure to do so could result in serious injury, or death.
7. Always use in a controlled manner. Failure to do so could result in
serious injury, or death.
8. Exercise with care to avoid injury.
9. If unsure about the proper use of the JONES PLATINUM strength
training system call your local dealer or our customer service
department at 800-990-5556.
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your
physician. This is especially important for individuals over the age of 35
or persons with pre-existing health problems. Recreation Supply, Inc.
assumes no responsibility for personal injury or property damage
sustained by or through use of this product.
1
29
42
23
17
42
29
23
6
40
41
12
37
44
37
44
24
21
15
16
24
1
3R
7A
4R
7B
7B
7A
4L
3L
2R
29
23
6
23
18
42
17
47
36
17
42
29
8
13
41
40
25
25
46
46
19
20
14
42
30
12
48
43
39
31
43
24
24
15
21
49
16
35
48
45
41
37
44
26
5
5
27
26
13
9
31
31
44
44
37
37
43
31
43
43
28
43
31
35
45
41
48
39
43
39
45
43
35
43
35
48
45
45
50
22
34
26
33
45
43
34
33
43
45
38
43
48
50
41
22
38
25
43
25
46
37
44
44
37
37
44
27
37
44
34
34
34
43
43
43
43
34
46
19
20
OVERVIEW
2
42
30
49
18
17
14
42
47
37
37
44
37
44
44
36
35
31
31
43
26
37
37
37
44
44
48
44
44
43
48
43
27
48
43
45
43
31
41
45
48
35
43
27
35
45
39
42
42
28
37
48
43
48
48
43
32
48
43
32
43
48
43
43
32
32
11A
11A
11A
11A
10A
1
2R
3R
3L
4R
4L
5
6
7A
7B
8
9
10A
11A
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
2
1
1
1
1
1
2
2
2
2
1
1
1
4
2
2
2
2
2
4
2
2
2
2
2
4
4
4
4
4
BASE FRAME
REAR BASE FRAME CONNECTOR
RIGHT UPRIGHT FRAME
LEFT UPRIGHT FRAME
RIGHT BAR RACK
LEFT BAR RACK
VERTICAL GUIDE ROD
(preassembled on Uprights)
HORIZONTAL GUIDE ROD
(pre-assembled in Base Frame)
SHROUD
SHROUD
OLYMPIC BAR
TOP FRAME
CHROMED CHIN UP BAR
BASE FRAME END PLATE
STEEL PLATE (preassembled on Base)
VERTICAL BEARING HOUSING
(preassembled on Uprights)
SAFETY SPOTTER
(preassembled on Uprights)
FOOT LATCH (preassembled on Base)
1/2" AXLE (w/3/8")
(preassembled on Base)
HOOK PLATE
(preassembled with Safety Spotter)
19 X 13 X 15L SHORT CONNECT
ROD (preassembled on Safety Spotter)
1" ID BIG WASHER
(preassembled on Uprights)
1" SPRING (preassembled on Uprights)
1/2" SPRING (preassembled on Uprights)
END CAP FOR CHIN UP BAR
(preassembled on chin up bar)
RUBBER STOPPER
(preassembled in Base Frame)
30mm BEARING
(preassembled in Base Frame)
25mm BEARING
(preassembled in Olympic Bar)
METAL MESH
(preassembled to Shrouds)
METAL MESH
(preassembled to Shrouds)
19
26 27
PARTS LIST
NO. DESCRIPTION QTY.
0 1/4
1/2
3/4 1/4
1/2
3/4 1/4
1/2
3/4 1/4
1/2
3/41" 2" 3" 4" 1/4
1/2
3/4 1/4
1/2
3/45" 6"
(inch)
3
1
2R
3R 3L
4R 4L
5
6
7A 7B
8 9 10A
11A 12 13 14 17
24
23
20
21
18
22
25
15 16
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
2
8
2
12
8
2
10
18
2
16
2
16
2
10
16
54
16
22
4
4
26
4
2
1/2" X 3" HEX THREADED BOLT
(preassembled on Safety Spotter)
1/2" X 1" HEX THREADED BOLT
1/2" X 1-3/4" HEX THREADED BOLT
(preassembled on Safety Spotter)
3/8" X 2-3/4" HEX BOLT
3/8" X 1-1/4" HEX BOLT
3/8" X 1-1/4" INNER HEX SCREW
3/8" X 1" INNER HEX SCREW
3/8" X 5/8" INNER HEX SCREW
PLASTIC KNOB
5/16" X 1/2" INNER HEX SCREW
5/16" X 1-1/4" COUNTER ALLEN
BOLT (preassembled to chin up bar)
M8 X 16 COUNTER ALLEN BOLT
5/16" X 5/8" SET SCREW
(preassembled on Base)
5/16" X 1/4" SET SCREW
(preassembled on Base)
1/2" WASHER
3/8" WASHER
5/16" WASHER
3/8" SPRING WASHER
R40 RETAINING RING
(pre-assembled in Bar)
1/2" NYLON NUT
3/8" NYLON NUT
MAGNET (preassembled on Uprights)
3/8" NUT
(preassembled on Chin Up Bar)
PARTS LIST
NO. DESCRIPTION QTY.
0 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4" 1/4 1/2 3/4 1/4 1/2 3/45" 6"
(inch)
4
29 33
28
34
35
38
36
39
40 41 42 43 44 45
46
47 48 49 50
31
30
37
32
STEP 1 Base Frame Assembly
5
IMPORTANT:
˙ To ease the assembly process, DO NOT tighten bolts until instructed.
˙ Please assemble on a flat level floor.
˙ Assembly requires three people during installation of the TOP FRAME.
1. Attach REAR BASE FRAME CONNECTOR (2R) to the BASE FRAME (1),
using eight 3/8" X 1" INNER HEX SCREWS (34) and eight 3/8" WASHERS
(43).
2. Attach four BASE FRAME END PLATES (11A) to the front and rear of the
BASE FRAME (1), using eight 1/2" X 1" HEX BOLTS (29) and eight 1/2"
WASHERS (42). NOTE: If you have purchased the optional Full Body Trainer
attachment, do not install the two END PLATES (11A) at the rear. Instead, you
will attach the Full Body Trainer there.
29
29
42
42
11A
11A
1
2R
34
34
43
43
43
43
43
43
43
43
34
34
42
11A
42
29
11A
1
29
0 1/4
1/2
3/4 1/4
1/2
3/4 1/4
1/2
3/4 1/4
1/2
3/41" 2" 3" 4" 1/4
1/2
3/4 1/4
1/2
3/45" 6"
(inch)
ENSURE BASE
FRAMES ARE
PARALLEL AND
TIGHTEN ALL BOLTS.
STEP 2 Right & Left Upright Frame Assembly
6
1. Attach the RIGHT UPRIGHT (3R) to the STEEL PLATE (12) on
the BASE FRAME (1) using five 3/8" WASHERS (45) and five
3/8" X 5/8" INNER HEX SCREWS (35).
2. Repeat above step for left side.
0 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4" 1/4 1/2 3/4 1/4 1/2 3/45" 6"
(inch)
35
35
35
35
35
35
45
45
45
45
45
45
45
45
45
45
1
1
12
Sr
Sl
12
STEP 3 Top Frame Assembly
7
1. Place one 3/8" X 5/8" INNER HEX SCREW (35) into each of the center holes in the
angled plates on the TOP FRAME (9). Using three people, lift the TOP FRAME (9)
into place, using the bolts to help align the TOP FRAME (9) with the RIGHT and
LEFT UPRIGHTS (3R & 3L). Once in place, attach the TOP FRAME (9) to the
RIGHT and LEFT UPRIGHTS (3R & 3L) by securing the two 3/8" X 5/8" INNER
HEX SCREWS (35) with two 3/8" SPRING WASHERS (45) and two 3/8" NYLON
NUTS (48). Continue to secure the TOP FRAME (9) to the RIGHT and
LEFT UPRIGHTS (3R & 3L) using four more 3/8" X 5/8" INNER HEX
SCREWS (35), 3/8" SPRING WASHERS (45), 3/8"
NYLON NUTS (48) for each side.
35
35
35
45
45
45
48
35
35
45
45
9
3R
3L
45
48
0 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4" 1/4 1/2 3/4 1/4 1/2 3/45" 6"
(inch)
2. Tighten the 3/8" X 5/8"
INNER HEX SCREWS (35)
at the base of the RIGHT
and LEFT UPRIGHTS
(3R & 3L) that were
installed in the previous
step 2. Then, tighten the
3/8" X 5/8" INNER HEX
SCREWS (35) at the top of
the RIGHT and LEFT
UPRIGHTS (3R & 3L) that
were placed in the
above step.
This step requires three people!
STEP 4 Right & Left Bar Rack Assembly
8
1. Attach RIGHT BAR RACK (4R) to the RIGHT UPRIGHT (3R), using six 3/8"
X 2-3/4" HEX BOLTS (31), twelve 3/8" WASHERS (43) and six 3/8" NYLON
NUTS (48).
2. Repeat the above instructions for the LEFT BAR
RACK (4L).
3. Tighten all
these bolts.
31
43
3R
43
48
43
48
43
48
43
48
43
48
43
43
41
40
43
31
43
43
31
43
31
43
31
43
3L
31
31
56
48
43
48
43
48
43
48
43
48
43
48
48
Tr
Tl
41
31
43
31
43
31
43
31
43
31
43
0 1/4
1/2
3/4 1/4
1/2
3/4 1/4
1/2
3/4 1/4
1/2
3/41" 2" 3" 4" 1/4
1/2
3/4 1/4
1/2
3/45" 6"
(inch)
A
D
B
C
1. As shown in Figs. A,B,C,D; slide one end of the OLYMPIC
BAR (8) in between the VERTICAL GUIDE ROD (5) and
the BAR RACK (4R) on the RIGHT UPRIGHT (3R) and the
other end of the OLYMPIC BAR (8) in between the
VERTICAL GUIDE ROD (5) and the LEFT BAR RACK
(4L) on the LEFT UPRIGHT (3R). Then hook the
OLYMPIC BAR (8) level on each side.
2. Slide a VERICAL BEARING HOUSING (13) up to match
up with the connector plate on the OLYMPIC BAR (8) and
attach using eight 3/8" X 1-1/4" HEX BOLTS (32), eight
3/8" WASHERS (43), eight 3/8" NYLON
NUTS (48). Tighten these bolts.
9
STEP 5 Olympic Bar Assembly
32
43
13
13
43
43
43
8
48
48
43
43
43
32
43
FRONT
FRONT
FRONT
FRONT
FRONT
STEP 6 Shroud Assembly
10
1. Attach WEIGHT SHROUD (7A) to the front of the
RIGHT UPRIGHT (3R) using four 5/16" WASHERS
(44) and four 5/16" X 1/2" INNER HEX SCREWS
(37), and to the rear of the LEFT UPRIGHT (3L)
using four 5/16" WASHERS (44) and four 5/16" X
1/2" INNER HEX SCREWS (37).
Wb
37
37
44
44
Wa
44 37
37
37
37
37
37
37
37
37
44
44
Wa
44
44
Sr
Sl
37
37
37
44
44
44
44
Wb
44
44
44
37
37
44
44
0 1/4
1/2
3/4 1/4
1/2
3/4 1/4
1/2
3/4 1/4
1/2
3/41" 2" 3" 4" 1/4
1/2
3/4 1/4
1/2
3/45" 6"
(inch)
2. Attach WEIGHT SHROUD (7B) to
the front of the LEFT UPRIGHT (3L)
using four 5/16" WASHERS (44)
and four 5/16" X 1/2" INNER HEX
SCREWS (37), and to the rear of
the RIGHT UPRIGHT (3R) using
four 5/16" WASHERS (44) and four
5/16" X 1/2" INNER HEX SCREWS
(37).
Assembly is complete! Please take the following steps before, and while
using the JONES PLATINUM Strength Training System:
1. Be certain all bolts are tightened securely. Check and tighten all
bolts before every use.
2. To best avoid injury, we always recommend training with a partner.
3. Always use the safety spotters! Failure to do so could result in
serious injury, or death. If you are unsure about the use of the safety
spotters, please call your local dealer, or us at 800-990-5556.
4. Be certain bar hooks are fully engaged before releasing your grip!
Failure to do so could result in serious injury, or death.
5. Always use collars to hold the weights on the Olympic Bar!
Check to make sure the collars will adequately hold in the event of
maximum failure of the user.
6. Always use in a controlled manner. Failure to do so could result in
serious injury, or death.
7. Exercise with care to avoid injury.
8. If unsure about the proper use of the JONES PLATINUM strength
training system call your local dealer or our customer service
department at 800-990-5556.
9. Keep children away from the Jones Platinum.
10. Enjoy many years of a Fit Lifestyle!
Please call us, or email us to let us know your thoughts! We love, and
strive to provide the world's best fitness equipment!
www.bodycraft.com
800-990-5556
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
BodyCraft Jones Platinum System Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
BodyCraft Jones Light Commercial Owner's manual
-
-
-
-
-
-
BodyCraft Jones Club Owner's manual
-
-
-
Other documents
-
Matrix MG-A47691 Owner's manual
-
-
Weider WEBE1606 User manual
-
-
-
-
-
FreeMotion 620 BE User manual
-
-
WeiderPro 15965 User manual