Danfoss DHP-AQ is an advanced heat pump system that provides efficient and environmentally friendly heating, cooling, and hot water solutions for your home. With its innovative technology, it offers a range of features to enhance your comfort and energy savings:
-
Efficient Heating and Cooling: The heat pump utilizes renewable energy sources to deliver efficient heating and cooling, reducing your reliance on traditional energy sources.
-
Hot Water Production: Selected models of Danfoss DHP-AQ provide hot water for domestic use, ensuring a reliable supply of hot water whenever you need it.
-
User-Friendly Control: The intuitive control system allows you to easily adjust settings, monitor energy consumption, and customize your heating and cooling preferences.
Danfoss DHP-AQ is an advanced heat pump system that provides efficient and environmentally friendly heating, cooling, and hot water solutions for your home. With its innovative technology, it offers a range of features to enhance your comfort and energy savings:
-
Efficient Heating and Cooling: The heat pump utilizes renewable energy sources to deliver efficient heating and cooling, reducing your reliance on traditional energy sources.
-
Hot Water Production: Selected models of Danfoss DHP-AQ provide hot water for domestic use, ensuring a reliable supply of hot water whenever you need it.
-
User-Friendly Control: The intuitive control system allows you to easily adjust settings, monitor energy consumption, and customize your heating and cooling preferences.
User manual
DHP-AQ
VUGFB102
Danfoss A/S reserves the right to make
changes to components and specifications
without prior notice.
© 2010 Danfoss A/S.
The Swedish language is used for the origi-
nal instructions. Other languages are a
translation of the original instructions.
(Directive 2006/42/EC)
Contents
1
Foreword ................................................................................................................................................. 3
2 Safety precautions ................................................................................................................................ 4
2.1 Installation and maintenance ............................................................................................................. 4
2.2 System modifications ............................................................................................................................. 5
2.3 Safety valve ................................................................................................................................................ 5
3 About your heat pump ....................................................................................................................... 6
3.1 Components and functions ................................................................................................................. 6
4 Control system .................................................................................................................................... 12
4.1 Keypad ...................................................................................................................................................... 12
4.2 Indicator ................................................................................................................................................... 12
4.3 Display ...................................................................................................................................................... 13
4.4 Main Menu ............................................................................................................................................... 15
5 Settings and adjustments ............................................................................................................... 16
5.1 Setting operating mode ..................................................................................................................... 16
5.2 Adjusting the indoor temperature ................................................................................................. 17
5.3 Distribution circuit 1 and 2 ................................................................................................................ 20
5.4 Hot water ................................................................................................................................................. 20
5.5 Cooling ..................................................................................................................................................... 20
5.6 Reading off temperatures .................................................................................................................. 21
5.7 Reading the operating time .............................................................................................................. 21
5.8 Manual defrost, outdoor unit ........................................................................................................... 21
5.9 Calendar ................................................................................................................................................... 22
5.10 Alarm history ........................................................................................................................................ 23
6 Regular checks .................................................................................................................................... 24
6.1 Checking operation .............................................................................................................................. 24
6.2 Check the water level in the heating circuit ................................................................................ 25
6.3 Checking safety valves ........................................................................................................................ 25
6.4 In the event of leakage ........................................................................................................................ 26
6.5 Cleaning the strainer for the heating circuit ............................................................................... 26
7 Default setting in the control computer .................................................................................... 28
8 Installation protocol .......................................................................................................................... 29
9 Check list ............................................................................................................................................... 30
10 Service schedule .............................................................................................................................. 32
VUGFB102 – 1
1 Foreword
Buying a heat pump from Danfoss is an investment in a better
future.
A Danfoss heat pump is classed as a renewable energy source, which
means that it is considerate of our environment. It is a safe and conven-
ient solution that provides heating, hot water and in certain cases cool-
ing, for your home at a low cost.
We thank you for the confidence that you have shown in us by buying a
heat pump from Danfoss. We hope that you will benefit from it for
many, many years to come.
With best wishes
Danfoss Heat Pumps
User manual VUGFB102 – 3
2 Safety precautions
The heat pump cover and control unit cover must only be
opened by authorised service technicians.
This product is not intended for persons (including children)
with reduced physical, sensory or psychological capacity, or
who do not have knowledge or experience, unless supervised
or they have received instructions on how the apparatus
functions from a safety qualified person.
Children are not permitted to play with the product.
Before changing the control computer’s settings, first find out what
these changes mean.
Contact your installer for any service work.
2.1 Installation and maintenance
DANGER! Only authorized installers may install, operate and
carry out maintenance and repair work on the heat pump.
DANGER! Only authorised electricians may carry out electrical
installations affecting the heat pump.
DANGER! Only authorized refrigeration technicians may work
on the refrigerant circuit.
4 – User manual VUGFB102
2.2 System modifications
Only authorized installers may carry out modifications on the following
components:
•
The heat pump unit
•
Water and electrical installations
•
The safety valve
Do not carry out construction installations that may affect the opera-
tional safety of the heat pump.
2.3 Safety valve
The following safety precautions apply to the hot water circuit’s safety
valve with corresponding overflow pipe:
•
Never block the connection to the safety valve’s overflow pipe.
•
Water expands when it is heated, this means that a small amount of
water is released from the system via the overflow pipe. The water
that exits the overflow pipe can be hot! Therefore, allow it to flow to
a floor drain where there is no risk of burning yourself.
User manual VUGFB102 – 5
3 About your heat pump
The heat pump is a complete heat pump installation that consists of two
basic units: a heat pump placed outdoors and a control unit placed
indoors. The control unit is available in three models in order to be able
to create as optimal system solution as possible, both in an existing
heating system that is to be upgraded and in new builds. Heating and
cooling are supplied to the house via a water borne heating system.
3.1 Components and functions
3.1.1
Outdoor unit
3
2
1
4
Pos. Description
1 Fan
2 Electrical cabinet
3 Air heat
exchanger
4 Refrigerant circuit
6 – User manual VUGFB102
3.1.2 Control unit
1
DHP-AQ Mini
1
2
4
3
5
DHP-AQ Maxi
1
2
3
4
DHP-AQ Midi
Position Description
1 Control module (transparent in image)
2 Immersion heater
3 Reversing valve
4 Circulation pump
5 Water heater
3.1.3 Heating
The heat pump can produce heat for heating (house, pool) and hot
water.
The hot water requirement is prioritised before the heating require-
ment. The heating requirement is calculated from outdoor temperature
and set heat curve. An auxiliary heater starts automatically on demand.
Heat production is as follows;
User manual VUGFB102 – 7
•
A fan draws the outdoor air through an air heat exchanger (1),
which heats up the cold refrigerant, which evaporates into a gas.
•
The refrigerant that is now supplied with energy in the form of heat
is transferred via the 4 way valve (2) to the compressor (3), where its
temperature and pressure are increased.
•
The extremely hot refrigerant continues to the flat heat exchanger
(4). Here, the refrigerant is cooled and releases its heat energy to the
heating system (5). The refrigerant’s temperature drops and con-
denses to a liquid state.
•
The heating system transports the heating energy out to the water
heater or the heating system of the house.
•
The refrigerant then passes through the drying filter (6) to the elec-
tronic expansion valve (7) where the pressure and temperature
drop and the process starts again.
1
2
3
4
5
6
7
8 – User manual VUGFB102
3.1.4 Hot water function
DHP-AQ Midi and DHP-AQ Maxi are adapted for hot water production.
Production of heating and hot water cannot occur at the same time
because the reversing valve for heating and hot water is positioned
after the heat pump and the immersion heater. Hot water production is
prioritised ahead of heat and cooling.
DHP-AQ Midi is connected to an existing water heater while DHP-AQ
Maxi has an integrated 180 litre heater equipped with a TWS coil (Tap
Water Stratificator) which gives more effective heat transfer and effi-
cient layering of water in the heater.
The temperature of the hot water cannot be adjusted. Normally, hot
water production does not cease at a determined temperature but
when the compressor’s operating pressure switch reaches its maximum
operating pressure, which corresponds to a hot water temperature of
approximately 50-55°C.
Using a regular time interval, the water in the water heater is given extra
heat by the integrated immersion heater to prevent the build up of bac-
teria, an anti-legionella function. The factory set time interval is seven
days (can be adjusted).
3.1.5 Defrost function
During operation the air heat exchanger is cooled by the energy
exchange, at the same time the humidity causes it to become covered
in frost at low outdoor temperatures. DHP-AQ has an automatic func-
tion to defrost the air heat exchanger using the energy from the house's
heating system.
Defrosting is initiated by low temperature in the refrigerant circuit after
the air heat exchanger and, among other things, is dependent on out-
door temperature, humidity and operating time. The length of defrost-
ing varies depending on the extent of freezing of the air heat
exchanger. Defrost continues until the air heat exchanger is free of ice
and the temperature starts to rise in the refrigerant circuit. After com-
pleted defrosting the heat pump returns to the operating mode before
defrosting.
3.1.6 Cooling function
The heart pump produces cooling through a similar process as the
defrosting function.
Cooling function is started by the heat pump control unit and is primar-
ily temperature controlled. The house's heating system is cooled by
User manual VUGFB102 – 9
transferring heat to the refrigerant circuit, which is then given off in the
air heat exchanger.
If the hot water heater is installed the control unit will alternate
between cooling and hot water production with prioritisation for the
hot water requirement.
3.1.7 Speed controlled fan
The fan starts at a nominal speed, which differs depending on the size of
output. The fan speed is adjusted up or down as required which is
determined by the temperatures in the refrigerant circuit.
3.1.8 Electronic expansion valve
When the refrigerant passes the expansion valve the pressure and tem-
perature of the refrigerant are reduced. In this way the energy in the
outdoor air is available to the refrigerant circuit. By regulating the open-
ing degree of the expansion valve one can optimise the flow in the
refrigerant circuit in different operating conditions. Control of the elec-
tronic expansion valve is based on the measurements of temperatures
and pressures in the refrigerant circuit and outside air.
3.1.9 Auxiliary heat
The auxiliary heater is included in DHP-AQ Midi and DHP-AQ Maxi and is
available as an accessory for DHP-AQ Mini. An auxiliary heater consists
of an immersion heater, which is located on the supply pipe ahead of
the reversing valve.
If the auxiliary heater is installed it engages AUTO mode automatically
when the heat demand is greater than the heat pump’s capacity.
Immersion heaters in DHP-AQ series intended for 400V voltage supply
have three heating elements (AUX. HEAT 1, 2 and 3) and can be control-
led in five power stages. Products for 230V have two heating elements
(AUX. HEAT 1 and 2) and are controlled in three power stages. The two
stages 4 and 5 cannot be engaged when the compressor is in operation
as opposed to stages +4 and +5 where it is possible.
230V 400V
Step 1 3 3
Step 2 6 6
Step 3 9 9
Step 4 12
10 – User manual VUGFB102
230V 400V
Step 5 15
Step +4 12
Step +5 15
3.1.10 Speed (rpm) control
A heat pump requires optimum conditions in the heating system in
order to be able to run as efficiently as possible. The temperature differ-
ence between the heating system’s supply line and return line must be
constant between 7–10°C. If the differences are greater or less, the heat
pump is less efficient and savings are lower.
The speed controlled circulation pump in DHP-AQ always ensures that the
temperature difference is retained. The control equipment detects if the
balance is upset and increases or decreases the speed of the circulation
pump as necessary.
User manual VUGFB102 – 11
4 Control system
The heat pump has an integrated control system which automatically
calculates the heating and cooling demand in the house to ensure that
the correct amount of heating and cooling is produced and emitted
where necessary.
The control panel is operated using a keypad and information is shown
in a display and by an indicator.
The information in the display and menus will vary depending
on the menu selection made and connected accessories.
2
1
3
ROOM
NO HEAT DEMAND
OPERAT. AUTO
20°C
1. Keypad
2.
Indicator
3. Display
4.1 Keypad
+ Plus sign used to scroll up a menu and increase the values.
- Minus sign used to scroll down a menu and reduce the values.
> Right arrow used to select a value or open a menu.
< Left arrow to cancel selection or exit a menu.
4.2 Indicator
The indicator at the bottom of the control panel has three modes:
12 – User manual VUGFB102
•
Not lit, means that the heat pump is not powered.
•
When the green light shines continuously, the heat pump has
power and is ready to produce heat, cooling or hot water.
•
Flashing green, means an active alarm.
4.3 Display
The display shows information about the heat pump’s operation, status
and any alarms.
Table 1. Symbols shown in the display.
Symbol Meaning
COMPRESSOR Indicates that the compressor is in operation.
LIGHTNING Indicates that the auxiliary heater is in operation. The
number indicates what additional step is activated.
HOUSE Indicates that the heat pump produces heat for the
heating system.
TAP Indicates that the heat pump produces heat for the
water heater.
F FLOW SENSOR Indicates that the flow sensor is active (there is flow).
CLOCK Indicates that tariff control is active.
TANK Indicates the level of hot water in the water heater.
When hot water is produced for the water heater, this
is indicated by a flashing icon for the tank. A lightning
symbol by the symbol indicates peak heating charg-
ing (anti-legionella function).
SQUARE Either indicates that the operating pressure switch has
deployed, or that the pressure pipe temperature has
reached its maximum temperature.
DEFROST Displayed when defrosting is active.
User manual VUGFB102 – 13
Symbol Meaning
FAN Displayed when the fan is active.
COOLING Displayed if cooling is produced.
A = Active cooling.
The following operating information may also appear:
Message Meaning
ROOM Shows the set ROOM value. Standard value: 20°C.
If the accessory room sensor is installed it shows the
actual temperature and the desired indoor temperature
is shown within brackets.
START Indicates that there is a need for heat production or hot
water and that the heat pump will start.
EVU STOP Indicates that the additional function EVU is active. EVU
is used to switch off the heat pump during high energy
tariffs.
NO HEAT DEMAND Indicates that there is no heating or hot water produc-
tion demand.
NO COOLING
DEMAND
Indicates that there is no cooling demand.
COMPRESSOR START
--XX
Indicates that there is a need for heat, hot water or cool-
ing and that the heat pump will start in XX minutes.
COMPRESSOR
+IMM.HEAT
Indicates that heat production is active with both com-
pressor and auxiliary heater.
START_MIN Indicates that there is a demand for heating or hot
water production but that a start delay is active.
AUX. HEATER Indicates that there is an auxiliary heater demand.
ACT COOLING Displayed if cooling is active.
DEFROST X(Y) Displayed when defrosting is active. X shows the actual
reached temperature. Y shows at what temperature
defrost is complete.
14 – User manual VUGFB102
4.4 Main Menu
The display's INFORMATION menu is used to set and adjust the heat
pump functions and is opened by pressing the left or right buttons. The
appearance of the menu will vary depending on the menu selection
made and connected accessories. The basic menu appears as follows:
INFORMATION
OPERAT.
HEATING
HOT WATER
DEFROST
CALENDAR
2
1
3
4
1. Sub-menus
2.
Return
3. Cursor
4. If an arrow is shown, it indi-
cates that more sub menus
are continued underneath
Press the + and - buttons to move the cursor between the sub-menus.
Press the right button to select a sub-menu. Press the left button to go
back in the menu.
User manual VUGFB102 – 15
5 Settings and adjustments
The installer carries out the basic settings of the heat pump at installa-
tion. A number of settings and adjustments that you can carry out your-
self are described below.
Before changing the control computer’s settings, first find out
what these changes mean. Make a note of the default setting.
5.1 Setting operating mode
OPERAT.
COMPRESSOR
AUX. HEATER
HOT WATER
AUTO
MANUAL TEST
1. Open the menu OPERAT. in the INSTAL-
LATION menu. The asterisk shows the
current selection
2. Mark new mode using + or – button.
3. Press the right button once to confirm
the choice.
4. Press the left button twice.
The following operating modes can be selected:
Operating
mode
Meaning
(OFF)
The installation is fully switched off. This mode is also
used to acknowledge certain alarms.
AUTO The heat pump regulates automatic compressor opera-
tion and auxiliary heater.
COMPRESSOR The control system is controlled so that only the heat
pump unit (compressor) is allowed to operate. In this
operating mode peak heating charging (anti-legionella
function) of the hot water will not run because the auxili-
ary heater is not used.
AUX. HEATER The control system only permits the auxiliary heater to be
in operation.
16 – User manual VUGFB102
Operating
mode
Meaning
HOT WATER In this mode the heat pump only produces hot water, no
heat goes to the heating system.
MANUAL TEST Only displayed when the value for MANUAL TEST is set to
2 in
The SERVICE menu. Outputs that control components are
activated manually.
Caution! If the operating mode OFF or HOT WATER is to be
used for long periods during the winter, the water in the
heating system in the heating system must be drained,
otherwise there is a risk of frost damage.
Alternatively the system solution with intermediate exchanger
should be used.
5.2 Adjusting the indoor temperature
The indoor temperature is adjusted by changing the heat pump’s heat
curve, which is the control system’s tool for calculating the heating
demand, the integral value. The integral value is determined by compar-
ing the actual temperature of the heating system's supply line with the
calculated value, the setpoint value.
The heating requirement is calculated from the current outdoor temper-
ature and heat curve setting.
The heat curve will be adjusted in connection with installation. It must
be adapted later on, however, to obtain a pleasant indoor temperature
in any weather conditions. A correctly set heat curve reduces mainte-
nance and gives energy efficient operation.
There are two ways of adjusting the heat curve, partly in the HEATING
sub-menu, partly with the ROOM value.
Adjusting CURVE
A typical heat curve is shown below. When the outdoor temperature is
0°C the heat pump control tries to make the temperature in the supply
line 40°C. At hotter or colder outdoor temperatures than 0°C the set
User manual VUGFB102 – 17
point that the control regulates against is lowered or raised respectively.
When you increase the CURVE value, the heat curve will become steeper
and when you reduce it, it will become flatter.
This is the most energy and cost efficient way to set the indoor tempera-
ture and should therefore be used for long term temperature settings.
4
2 0 0 -2 0
2 4
4 0
5 6
2
3
1
5
1. Supply temperature (°C)
2.
Maximum setpoint value
3. Outdoor temperature (°C)
4. 0°C
5. Set value (standard 40°C)
The following parameters can be adjusted in the HEATING menu:
Parameter Description
CURVE If the CURVE value is increased, the heat curve will become
steeper and if the value is reduced, it will become flatter. Raise
or lower as necessary to obtain as even an indoor temperature
as possible.
MIN Lowest set point for supply temperature.
MAX Highest set point for supply temperature.
CURVE 5 Used to adjust the heat curve at an outdoor temperature of
+5°C.
CURVE 0 Used to adjust the heat curve at an outdoor temperature of 0°C
CURVE -5 Used to adjust the heat curve at an outdoor temperature of
-5°C.
18 – User manual VUGFB102
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
Danfoss DHP-AQ is an advanced heat pump system that provides efficient and environmentally friendly heating, cooling, and hot water solutions for your home. With its innovative technology, it offers a range of features to enhance your comfort and energy savings:
-
Efficient Heating and Cooling: The heat pump utilizes renewable energy sources to deliver efficient heating and cooling, reducing your reliance on traditional energy sources.
-
Hot Water Production: Selected models of Danfoss DHP-AQ provide hot water for domestic use, ensuring a reliable supply of hot water whenever you need it.
-
User-Friendly Control: The intuitive control system allows you to easily adjust settings, monitor energy consumption, and customize your heating and cooling preferences.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Danfoss DHP-M User guide
-
-
-
-
-
-
-
-
-