2. Home
  3. Domestic appliances
  4. Small kitchen appliances
  5. Blenders
  6. MULTIPLEX
  7. UI 4.0.10

MULTIPLEX UI 4.0.10 Operating instructions

  • Hello! I've reviewed the instruction sheet for the MULTIPLEX BIC MF Blender Shaft Replacement Tool. This document provides detailed instructions on how to replace the blender shaft, including necessary tools, parts, and safety precautions. The document also covers the procedure for resetting the blender cycle counts. I'm ready to answer your questions about this process and the device.
  • What software version is required to update the blender cycle counts?
    What should I do before replacing the blender shaft?
    What is the first step in removing the old blender shaft?
    What is the next step after the hubs are locked together for shaft replacement?
    What should I do after the installation of the new blender shaft
Instruction Sheet Subject: BIC Manual Fill Blender Shaft Replacement Tool
SCOPE: MULTIPLEX BIC MF UNITS UI 4.0.10 AND UP
1 of 4
 DocumentNumber:020008383 March7,2023
MULTIPLEX
645 PARK EAST BOULEVARD SUITE 5, NEW ALBANY, IN 47150
844-724-CARE
WWW.MULTIPLEXBEVERAGE.COM
Refreshing the Experience
Theunitmusthavethefollowingsoftwareornewerbefore
updatingblendercyclecounts:
• UISoftwareversion4.0.10orUP
• MixerSoftwareversion0.19.0orUP
BlenderShaftReplacementKitsareavailableforblender
shaftswithclosed(USA)oropenbellhousings.
OPEN BELL HOUSING CLOSED BELL HOUSING
TOOLS REQUIRED
• SafetyPunctureProofGloves
PARTS REQUIRED
• 020008908OPENBellHousingBlenderShaft
ReplacementKit(kitpartslistedbelow)
QTY DESCRIPTION PART NUMBER
2OPENBELLHOUSINGBLENDERSHAFT 020008344
1TOOLSHAFTLOWERV2 020008907
1TOOLSHAFTUPPER 020008380
2TOOLSHAFTCLIP 020008381
1SHEETINSTRUCTIONSSHAFT 020008383
--OR--
• 020008385CLOSED(USA)BellHousingBlenderShaft
ReplacementKit(kitpartslistedbelow)
QTY DESCRIPTION PART NUMBER
2CLOSEDBELLHOUSINGBLENDERSHAFT 020008742
1TOOLSHAFTLOWERV1 020008386
1TOOLSHAFTUPPER 020008380
2TOOLSHAFTCLIP 020008381
1SHEETINSTRUCTIONSSHAFT 020008383
nWarning
Blendershaftcontainssharpblades.DoNOTtouchthe
blades.
Important
Keep refrigeration cabinet door closed so product
remainschilled.
PREPARATION
1. VerifyyouhaveallfourpiecesoftheBlenderShaft
ReplacementTool:one(1)UpperHub,one(1)Lower
Hub,andtwo(2)CupHolderClips.
Cup Holder ClipsUpper Hub Lower Hub
2. PowerunitOFFusingswitchlocatedonLEFTsideofunit
andunplugunitfrompowersource.
OFF
REMOVE BLENDER SHAFT
3. Putonsafetypunctureproofgloves.
4. Removegratefromblenderareathenremoveplasticdoor.
2 of 4
DocumentNumber:020008383 March7,2023
Subject:BICManualFillBlenderShaftReplacementTool
5. Pullthecupholderapproximatelyhalfwaydowninthe
blenderarea.
6. InstallCupHolderClips.
A. Liftthecupholderupasfaraspossible.
B. Whileholdingthecupholderupinstallthetwo(2)
CupHolderClipsinplacetoholdthecupholderup
outoftheway.
C. Theblendershaftwillremaininpositioninthe
middleofthechamber.
7. PlacetheUpperHubovertheblendershaftasshownbelow.
• FortheOPENbellhousingshaft,theUpperHub
willsitlooselyontopofthebellhousing.
• FortheCLOSEDbellhousingshaft,rotatethe
UpperHubuntilitdropsinplaceandcanno
longerberotated.
8. WhileholdingtheUpperHubinplace,raisetheLower
HubtoengagewiththeUpperHub.
• FortheOPENbellhousingshaft,rotatetheLower
Hubuntiltheshaftfitsintotheslotsthentwistthe
UpperHubinthedirectionofthe“REMOVE”arrow.
OPEN BELL HOUSING
• FortheCLOSEDbellhousingshafttwisttheLower
Hubinthedirectionofthe“REMOVE”arrow.
CLOSED BELL HOUSING
D. Thetwohubswilllocktogether.
E. Oncethehubsarelockedtogether,twisttheLower
Hubinthedirectionofthe“REMOVE”arrowto
removetheoldshaftfromthemotor.
3 of 4
DocumentNumber:020008383 March7,2023
Subject:BICManualFillBlenderShaftReplacementTool
NOTE:Theblendershafthasalongthreadanditmaytake
timetocompletelyremoveshaftfrommotor.Usecaution
nottocrossthreadtheshaft.
9. RemoveLowerandUpperHubsfromoldblendershaft.
A. LeaveCupHolderClipsinplace.
B. RemovetheLowerandUpperHubsfromtheold
blendershaftbyholdingtheUpperHubfirmlyin
placeandtwistingtheLowerHubinthedirectionof
the“INSTALL”arrow.
C. Thiswillunlockthetwohubsandallowremovingthe
toolfromtheoldshaft.
INSTALL BLENDER SHAFT
10.ConnectLowerandUpperHubstonewblendershaft
bytwistingtheLowerHubinthedirectionofthe
“INSTALL”arrow.
11.Installnewblendershaft.
A. Placethetopoftheblendershaftintotheopeninginthe
blendareaandtiltintothemiddleholeofthecupcover.
B. Threadthenewblendershaftintomotorbyturningin
thedirectionofthe“INSTALL”arrowontheLowerHub.
C. Continuetoturntooluntilnewshaftstopsturningand
shaftistightenedintoplace.Itwilltakesometime
tocompletelythreadthenewblendershaftintothe
motor.Usecautionnottocrossthreadtheshaftinto
themotor.
NOTE:Theshaftshouldonlybehandtight.Neverusea
ratchettoinstalltheblendershaft.
12.RemoveUpperandLowerHubsfromnewblendershaft
byholdingtheUpperHubandblendershaftfirmlyand
turntheLowerHubinthedirectionofthe“INSTALL”
13.Holdingcupcoverfirmly,removeCupHolderClips.
14.Carefullylowercupcover.
15.Repeatprocesstoreplaceotherblendershaft.
NOTE:Itisrecommendedtoreplacebothblendershaftsat
thesametime.
4 of 4
DocumentNumber:020008383 March7,2023
Subject:BICManualFillBlenderShaftReplacementTool
REASSEMBLY
16.Verifycupalignmentringsareinstalledinblendergrate.
Notifymanagerifmissing.
17.Replacegrateinblenderareathenreinstallplasticdoor.
18.PlugunitINandpowerunitON.
BLENDER CYCLE COUNTS
19.Resetblendercyclecount.
NOTE:TherearetwodifferentUserInterface(UI)
screensthatareusedonBlend-in-Cup(BIC)units.
CommonController
GlassScreen
MR7
PlasticOverlay
MR7WITHSOFTWARE4.0.10OR5.0.10
FromeasyToUCHscreenpressMANAGERMENU
Press“A”forpasswordthenpressGREENcheck
ArrowDOWNone(1)time
PressSHAFTREPLACEMENT
EntercorrectpasswordthenpressGREENcheck
PART REPLACED PASSWORD
RIGHTSHAFT SHAFTR
LEFTSHAFT SHAFTL
Presscheckonconfirmation
Ifbothshaftsreplacedrepeatprocessusingcorrect
password.
PressBACKarrowuntilreturntoeasyToUCHscreen
COMMONCONTROLLERSOFTWARE06.00.01ORHIGHER
FromeasyToUCHscreenpressSERVICE
Press“A”forpasswordthenpressGREENcheck
PressPLANNEDMAINTENANCE
PressMIXERMAINTENANCEPERFORMED
EntercorrectpasswordthenpressGREENcheck
PART REPLACED PASSWORD
RIGHTSHAFT SHAFTR
LEFTSHAFT SHAFTL
Presscheckonconfirmation
Ifbothshaftsreplacedrepeatprocessusingcorrect
password.
PressBACKarrowuntilreturntoeasyToUCHscreen
20.Performdailycleaning/sanitizingofunit.
21.Makeadrinkoneachsidetoconfirmoperationwith
manager.
FOR MORE BIC INFORMATION VISIT
BlenderShaftVideo
https://www.multiplexbeverage.com/asset
/?id=gbpeic&regions=us&prefLang=en-US
/