Joker MACHINE 2014-UP User manual

Type
User manual

The Joker Machine 2014-UP HD Speedometer Side Mount is designed to provide a secure and stylish mounting solution for your Harley-Davidson speedometer. It features a swivel clamp for easy installation and adjustment, and is compatible with Sportster Custom and Forty-Eight models when used with the Harley-Davidson speedo back plate and cushioning. The mount also includes integrated LED indicators for a sleek, modern look.

The Joker Machine 2014-UP HD Speedometer Side Mount is designed to provide a secure and stylish mounting solution for your Harley-Davidson speedometer. It features a swivel clamp for easy installation and adjustment, and is compatible with Sportster Custom and Forty-Eight models when used with the Harley-Davidson speedo back plate and cushioning. The mount also includes integrated LED indicators for a sleek, modern look.

For technical support contact Joker Machine
2245 Kiowa Blvd N. Ste. 100, Lake Havasu City, AZ 86403
PHONE: 909-596-9690, FAX: 909-596-9693
[email protected], www.jokermachine.com
2014-UP HD SPEEDOMETER
SIDE MOUNT ASSEMBLY INSTRUCTIONS
090126-I-2014-2021 7/8/2022
JOKER INDICATOR
LED'S
WIRE FROM HARLEY
WIRE HARNESS
QUICK CONNECTS
WIRE CONNECTING NOTES:
Mount clamp and speedo housing on left fork
Lift bike on bike stand to get the front wheel off the
ground.
Loosen upper and lower triple clamp pinch bolts.
Slide fork tubes down far enough to place clamp on
left fork tube. Slide fork tubes back into place and
torque to factory spec. 30' - 35' lbs.
Slide fork clamp bolt through the fork clamp mount
into the speedometer mount using a 6mm hex
driver/key.
Remove speedo from stock bracket by removing
back plate, reset swtich, plug and cushioning from
OEM speedometer clamp.
Swivel Clamp Installation skip steps 1-3.
If using the swivel clamp you do not have to lift the
bike on a bike stand to lower the fork tube legs.
1.
2.
3.
4.
Reassemble on the Joker speedometer side mount.
Cut the wires at the base of the stock indicator light module.
Now the wires from the stock indicators must be matched
up and trimmed to splice to the new indicators wires.
We supply the smallest butt connectors so be cautious
that your crimper will work on these and not just smash
them. You may choose to solder and heat shrink the wires.
We like to cover the wire bundle with a plastic bellows
style loom using small tie-wraps about every 1-1/2"
inches. This helps the bundle stay in a smooth curve.
Using BLUE LOCTITE mount speedo side mount to
fork clamp.
Make sure you clear the gas tank before tighting down
mounting screw.
5.
6.
7.
8.
9.
10.
11.
IMPORTANT! Sportster Custom and Forty-Eight models
require the Harley-Davidson speedo back plate and
cushioning (HD #67320-95 & 67104- 95).
Washer
Speedo Bracket
M8-1.25 Socket Cap Screw
NOTE: BLUE LOCTITE
before final installation
Fork Clamp
Orange (battery fuse)
Brown Orange & Blue
Orange & White
White
Blue & White
Pink & Blue
Orange & Red
Violet
Orange / White
White
Blue
Pink
Orange
Green
Violet
White
Grey
21-Up Stock wire color20 and earlier stock wires
  • Page 1 1

Joker MACHINE 2014-UP User manual

Type
User manual

The Joker Machine 2014-UP HD Speedometer Side Mount is designed to provide a secure and stylish mounting solution for your Harley-Davidson speedometer. It features a swivel clamp for easy installation and adjustment, and is compatible with Sportster Custom and Forty-Eight models when used with the Harley-Davidson speedo back plate and cushioning. The mount also includes integrated LED indicators for a sleek, modern look.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI