V I V O DESK-E-100W User manual

Brand: V I V O

Model: DESK-E-100W

Type: User manual

White Electric Single Motor Desk Frame

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/desk-e-100b

SKU: DESK-E-100W

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a

qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may

cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual

and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect

assembly, or inappropriate use.

WARNING!

PACKAGE CONTENTS

ELECTRICAL SAFETY INSTRUCTIONS

THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC

SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.

• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.

• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.

• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR

SELLER TO REPLACE DAMAGED PARTS.

• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE

MADE CONTACT WITH LIQUIDS.

• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.

• OUTDOOR USE IS PROHIBITED.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

H (x16)

ST4.8x16

I (x2)

ST2.9x15

O (x1)

Power Cord

M (x1)

Controller

N (x1)

AC Adapter

P (x6)

Cable Clip

S (x1)

2mm Allen

Wrench

T (x1)

5mm Allen

Wrench

A (x1)

Telescopic

Cross Bar Set

B x1)

Motorized Leg

C x1)

Non-motorized

Leg

D (x2)

Side Brackets

E (x2)

Foot

J x4)

M6x8

L x8)

M6x30

K x12)

M6x10

Q (x2)

Screw-on

Eyelet

R (x2)

10" Ziptie

F (x1)

Sync Rod

Center Sha

G (x2)

Sync Rod Hex

Sha

176lbs

(80kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1

Loosely assemble the Telescopic Cross Bar Set (A) making sure the locking holes are facing up as

shown below. Partially insert M6x8 bolts (J) into the locking holes using Allen Wrench (T), making sure

the Cross Bar is still able to slide freely.

TOOLS NEEDED

Phillips

Screwdriver Drill Tape

Measure

STEP 2

Attach Cross Bar (A) to both the Motorized Leg (B) and Non-motorized Leg (C) using M6x10 bolts (K),

making sure the locking bolts are still facing up on the Cross Bar. Tighten with Allen Wrench (T).

STEP 3

Attach Side Brackets (D) to both ends of the frame using M6x10 bolts (K). Tighten with Allen Wrench (T).

STEP 4

Place a foot (E) on each leg as shown below. Attach each foot using M6x30 bolt (L). Tighten with Allen

Wrench (T).

STEP 5

STEP 6

Insert one of the Sync Rod Hex Shas (G) through the motor and into the Motorized Leg (B).

NOTE: If the hex does not line up with the leg, temporarily plug the Motorized Leg (B) and the AC Adapter

(N) into the Controller (M) (see step 10 for details). Then, while pushing on the hex sha, very briefly

press the up and down arrows (alternating between the two buttons so the legs will still be even when

assembled) until the sha slides into the leg.

FOR VIVO DESKTOP: Adjust frame width until the Side Bracket (D) holes line up with the pre-drilled

holes on the desktop. Adjust center crossbar section until all M6x8 bolts (J) are able to make contact,

then fully tighten using Allen Wrench (T). To attach the desktop, refer to the manual included with your

desktop. Set aside x2 of the ST4.8x16 screws (H) for mounting the AC Adapter (N).

FOR OTHER DESKTOP: Adjust the frame to the desired width while making sure the overhang does

not exceed 10" on either side. Adjust center crossbar section until all M6x8 bolts (J) are able to make

contact, then fully tighten using Allen Wrench (T). Mark and drill pilot holes to a depth of 3/8" (10mm)

using a 1/8" (3mm) bit where the Side Brackets (D) align on the desktop. Secure the frame using

ST4.8x16 screws (H) to the desktop. Set aside x2 of the ST4.8x16 screws (H) for mounting the AC

Adapter (N).

Center the Sync Rod Center Sha (F) so it rest's evenly on both Sync Rod Hex Shas (G). When in place,

tighten the preinstalled set screws using the smaller Allen Wrench (S).

Note: Be sure not to pull out the hex shas from either leg.

STEP 8

Loosen the preinstalled set screws on the Sync Rod Center Sha (F) using Allen Wrench (S). Slide the

Sync Rod Center Sha (F) onto the installed motor Sync Rod Hex Sha (G) as far as it will go. Then install

the second Sync Rod Hex Sha (G) into the Sync Rod Center Sha (F). Then slide the second Hex Sha

into the Non-motorized Leg (C).

NOTE: If the hex does not line up with the leg, temporarily plug the motorized leg (B) and the AC

Adapter (N) into the Controller (M) (see step 10 for details). Then, while pushing on the sha, very briefly

press the up and down arrows (alternating between the two buttons so the legs will still be even when

assembled) until the sha slides into the leg.

STEP 7

Attach the Controller (M) to the desktop using ST2.9x15 screws (I), making sure it is on the side of the

Motorized Leg (B).

STEP 9

SET SCREWS

CAUTION!

Failure to follow these instructions may result in property damage and/or personal injury.

Do not exceed desk

weight limit.

Keep area of vertical

motion free of

obstacles.

Keep weight on desk

balanced for correct

operation and longer

life of components.

Leave enough slack in

cables to allow for full

range of vertical motion.

STEP 11

If necessary, adjust foot pads at the bottom of foot (E) to level the desk.

STEP 10

Plug cables together as shown below. Tidy up cables using Cable Clips (P). Attach AC Adapter (N) to

desktop using ST4.8x16 screws (H), the Screw-on Eyelets (Q), and 10" Zipties (R) as shown below.

Note: A desk reset is required before use. Refer to the Controller User Guide for operational

instructions. Ensure there is enough slack in the cables at the lowest and highest positions before use.

2.75"

(70mm)

LAST UPDATED: 03/08/2022

REV3.1

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

V I V O DESK-E-100W User manual

V I V O DESK-E-100W User manual

V I V O DESK-E-100W User manual

Related papers

Other documents