FLIR Quasar User manual

This document does not contain any export-controlled information.

Quasar™

Installation and

User Guide

4K IR PTZ Cameras

i

22x CP-6408-21-I

31x CP-6408-31-I

CP-6408 Range Installation and User Guide - Revision 120 - September 2020

This document does not contain any export-controlled information.

copied, photocopied, translated, or transmitted to any electronic medium or machine readable form without the

prior written permission of FLIR Systems, Inc..

Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR

Systems, Inc. and/or its subsidiaries. All other trademarks, trade names, or company names referenced herein are

used for identification only and are the property of their respective owners.

This product is protected by patents, design patents, patents pending, or design patents pending.

Photographs and images appearing in this manual may have been modified for illustrative purposes using

commercial image editing software and may not always reflect an actual product configuration.

The contents of this document are subject to change without notice.

For additional information visit www.flir.com or write to FLIR Systems, Inc.

FLIR Systems, Inc.

6769 Hollister Avenue

Goleta, CA 93117

Support: https://www.flir.com/support/

product.enterprise.support@flir.com

Important Instructions and Notices to the User:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Modification of this device without the express authorization of FLIR Systems, Inc. may void the user’s authority

under FCC rules to operate this device.

Note 1: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at the user’s own

expense.

Note 2: If this equipment came with shielded cables, it was tested for compliance with the FCC limits for a Class A

digital device using shielded cables and therefore shielded cables must be used with the device.

Industry Canada Notice:

This Class A digital apparatus complies with Canadian ICES-003.

Avis d’Industrie Canada:

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Proper Disposal of Electrical and Electronic Equipment (EEE)

The European Union (EU) has enacted Waste Electrical and Electronic Equipment Directive

2012/19/EU (WEEE), which aims to prevent EEE waste from arising; to encourage reuse,

recycling, and recovery of EEE waste; and to promote environmental responsibility.

In accordance with these regulations, all EEE products labeled with the “crossed out wheeled

bin” either on the product itself or in the product literature must not be disposed of in regular

rubbish bins, mixed with regular household or other commercial waste, or by other regular

municipal waste collection means. Instead, and in order to prevent possible harm to the

environment or human health, all EEE products (including any cables that came with the

product) should be responsibly discarded or recycled.

Document History

Revision

Date

Comment

100

February 2020

v1.6.0.16 - Initial FLIR release of CP-6408-21-I camera

110

June 2020

Added Class 1 Laser Product compliance-related content

120

September 2020

v1.6.0.31 - Initial FLIR release of CP-6408-31-I camera

iiCP-6408 Range Installation and User Guide - Revision 120 - September 2020

This document does not contain any export-controlled information.

Register your Product with FLIR at https://customer.flir.com.

For warranty information, see https://www.flir.com/support-center/warranty/security/flir-security-product-

warranties/.

Product Registration and Warranty

Information

iiiCP-6408 Range Installation and User Guide - Revision 120 - September 2020

This document does not contain any export-controlled information.

Table of Contents

ivCP-6408 Range Installation and User Guide - Revision 120 - September 2020

1. Document Scope and Purpose .......................................................................................... 1

2. Camera Overview .............................................................................................................. 5

Accessing Product Information from the FLIR Website .................................................... 6

2.1

Camera Dimensions .................................................................................................... 8

2.2

3. Installation ......................................................................................................................... 9

Supplied Components .................................................................................................. 9

3.1

Site Preparation ......................................................................................................... 10

3.2

Camera Connections .................................................................................................. 11

3.3

Supplying Power to the Camera .................................................................................. 12

3.4

Waterproofing the Camera .......................................................................................... 14

3.5

Mounting the Camera ................................................................................................. 14

3.6

Securing the Camera ..................................................................................... 143.6.1

Wall Mount Bracket CX-ARMX-G3 .................................................................. 163.6.2

Wall Mount Bracket with Power Box CX-ELBX-G3 ............................................ 173.6.3

Gooseneck Mount with Power Box CX-GSNK-G3 ............................................. 193.6.4

Mount Adapters ............................................................................................ 203.6.5

Corner Adapter CX-CRNR-G3 ............................................................................................. 20

3.6.5.1

Pole Adapter CX-POLE-G3 .................................................................................................. 22

3.6.5.2

Initial Configuration ..................................................................................................... 23

3.7

Configure for Networking ................................................................................ 233.7.1

Change Video Format (Optional) ..................................................................... 253.7.2

Install and Test the Optional Wash Kit ............................................................ 253.7.3

Attach the Camera to a VMS ......................................................................... 283.7.4

4. Operation ......................................................................................................................... 29

Accessing the Camera ............................................................................................... 29

4.1

View Settings Home Page .......................................................................................... 29

4.2

Video Page ............................................................................................................... 31

4.3

Visible Page .............................................................................................................. 33

4.4

Input/Output (I/O) Page .............................................................................................. 37

4.5

PTZ Page .................................................................................................................. 38

4.6

Illumination Page ....................................................................................................... 40

4.7

OSD Page ................................................................................................................ 40

4.8

Wiper Page (CP-6408-31-I only) .................................................................................. 40

4.9

Georeference Page .................................................................................................... 42

4.10

5. Configuration ................................................................................................................... 43

Network Page ............................................................................................................ 43

5.1

This document does not contain any export-controlled information.

Table of Contents

vCP-6408 Range Installation and User Guide - Revision 120 - September 2020

Date & Time Page ..................................................................................................... 44

5.2

Users Page ............................................................................................................... 45

5.3

Cloud Page ............................................................................................................... 47

5.4

Audio Page ............................................................................................................... 47

5.5

I/O Devices Page ....................................................................................................... 48

5.6

Cyber Page ............................................................................................................... 49

5.7

Certificates ................................................................................................... 495.7.1

802.1x .......................................................................................................... 515.7.2

TLS/HTTPS .................................................................................................. 515.7.3

Services ....................................................................................................... 515.7.4

ONVIF Page .............................................................................................................. 52

5.8

Firmware & Info Page ................................................................................................. 53

5.9

6. Maintenance and Troubleshooting Tips ........................................................................... 55

Cleaning ................................................................................................................... 55

6.1

Troubleshooting ......................................................................................................... 55

6.2

This document does not contain any export-controlled information.

Document Scope and Purpose

1CP-6408 Range Installation and User Guide - Revision 120 - September 2020

1 Document Scope and Purpose

The purpose of this document is to provide installation, operation, and configuration instructions for Quasar

CP-6408 cameras.

Note:

This document is intended for use by technical users who have a basic understanding of CCTV

camera/video equipment and LAN/WAN network connections.

Remarque:

Ce document est destiné aux utilisateurs techniciens qui possèdent des connaissances de base des

équipements vidéo/caméras de télésurveillance et des connexions aux réseaux LAN/WAN.

Disclaimer

Users of FLIR products accept full

responsibility for ensuring the suitability and

considering the role of the product detection

capabilities and their limitation as they apply to

their unique site requirements.

FLIR Systems, Inc. and its agents make no

guarantees or warranties to the suitability for

the users’ intended use. FLIR Systems, Inc.

accepts no responsibility for improper use or

incomplete security and safety measures.

Failure in part or in whole of the installer,

owner, or user in any way to follow the

prescribed procedures or to heed WARNINGS

and CAUTIONS shall absolve FLIR and its

agents from any resulting liability.

Specifications and information in this guide are

subject to change without notice.

Avis de non-responsabilité

Il incombe aux utilisateurs des produits FLIR de vérifier

que ces produits sont adaptés et d'étudier le rôle des

capacités et limites de détection du produit appliqués

aux exigences uniques de leur site.

FLIR Systems, Inc. et ses agents ne garantissent

d'aucune façon que les produits sont adaptés à l'usage

auquel l'utilisateur les destine. FLIR Systems, Inc. ne

pourra être tenu pour responsable en cas de mauvaise

utilisation ou de mise en place de mesures de sécurité

insuffisantes.

Le non respect de tout ou partie des procédures

recommandées ou des messages d'AVERTISSEMENT

ou d'ATTENTION de la part de l'installateur, du

propriétaire ou de l'utilisateur dégagera FLIR Systems,

Inc. et ses agents de toute responsabilité en résultant.

Les spécifications et informations contenues dans ce

guide sont sujettes à modification sans préavis.

A Warning is a precautionary message that indicates a procedure or condition where there are

potential hazards of personal injury or death.

Avertissement est un message préventif indiquant qu'une procédure ou condition présente un risque

potentiel de blessure ou de mort.

This document does not contain any export-controlled information.

Document Scope and Purpose

2CP-6408 Range Installation and User Guide - Revision 120 - September 2020

A Caution is a precautionary message that indicates a procedure or condition where there are potential

hazards of permanent damage to the equipment and or loss of data.

Attention est un message préventif indiquant qu'une procédure ou condition présente un risque

potentiel de dommages permanents pour l'équipement et/ou de perte de données.

A Note is useful information to prevent problems, help with successful installation, or to provide

additional understanding of the products and installation.

Une Remarque est une information utile permettant d'éviter certains problèmes, d'effectuer une

installation correcte ou de mieux comprendre les produits et l'installation.

A Tip is information and best practices that are useful or provide some benefit for installation and use of

FLIR products.

Un Conseil correspond à une information et aux bonnes pratiques utiles ou apportant un avantage

supplémentaire pour l'installation et l'utilisation des produits FLIR.

General Cautions and Warnings

This section contains information that indicates a

procedure or condition where there are potential

hazards.

SAVE ALL SAFETY AND OPERATING INSTRUCTIONS

FOR FUTURE USE.

Although the unit is designed and manufactured in

compliance with all applicable safety standards, certain

hazards are present during the installation of this

equipment.

To help ensure safety and to help reduce risk of injury

or damage, observe the following:

Précautions et avertissements d'ordre

général

Cette section contient des informations indiquant

qu'une procédure ou condition présente des risques

potentiels.

CONSERVEZ TOUTES LES INSTRUCTIONS DE

SÉCURITÉ ET D'UTILISATION POUR POUVOIR VOUS Y

RÉFÉRER ULTÉRIEUREMENT.

Bien que l'unité soit conçue et fabriquée conformément

à toutes les normes de sécurité en vigueur, l'installation

de cet équipement présente certains risques.

Afin de garantir la sécurité et de réduire les risques de

blessure ou de dommages, veuillez respecter les

consignes suivantes:

This document does not contain any export-controlled information.

Document Scope and Purpose

3CP-6408 Range Installation and User Guide - Revision 120 - September 2020

Warning:

Installation must follow safety, standards, and electrical codes as well as the laws that apply where the

units are being installed.

The unit’s cover is an essential part of the product. Do not open or remove it.

Never operate the unit without the cover in place. Operating the unit without the cover poses a risk of fire

and shock hazards.

Do not disassemble the unit or remove screws. There are no user serviceable parts inside the unit.

Only qualified trained personnel should service and repair this equipment.

Observe local codes and laws and ensure that installation and operation are in accordance with fire,

security and safety standards.

Avertissement:

L'installation doit respecter les consignes de sécurité, les normes et les codes électriques, ainsi que la

législation en vigueur sur le lieu d'implantation des unités.

Le cache de l'unité est une partie essentielle du produit. Ne les ouvrez et ne les retirez pas.

N'utilisez jamais l'unité sans que le cache soit en place. L'utilisation de l'unité sans cache présente un

risque d'incendie et de choc électrique.

Ne démontez pas l'unité et ne retirez pas ses vis. Aucune pièce se trouvant à l'intérieur de l'unité ne

nécessite un entretien par l'utilisateur.

Seul un technicien formé et qualifié est autorisé à entretenir et à réparer cet équipement.

Respectez les codes et réglementations locaux, et assurez-vous que l'installation et l'utilisation sont

conformes aux normes contre l'incendie et de sécurité.

Warning:

Do not drop the camera or subject it to physical shock.

Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of

ethanol and wipe it gently. If the camera will not be used for an extended period of time, put on the lens

cap to protect the sensor from dirt.

Do not aim the camera lens at strong light, such as the sun or an incandescent lamp, which can

seriously damage the camera.

Make sure that the surface of the sensor is not exposed to a laser beam, which could burn out the

sensor.

If the camera will be fixed to a ceiling, verify that the ceiling can support more than 23 newtons (23-N) of

gravity, or over three times the camera’s weight.

The camera should be packed in its original packing if it is reshipped.

This document does not contain any export-controlled information.

Document Scope and Purpose

4CP-6408 Range Installation and User Guide - Revision 120 - September 2020

Caution:

To avoid damage from overheating or unit failure, assure that there is sufficient temperature regulation to

support the unit’s requirements (cooling/heating). Operating temperature should be kept within the range

specified by the camera's technical specifications.

Attention:

Afin d'éviter tout dommage dû à une surchauffe ou toute panne de l'unité, assurez-vous que la régulation de

température est suffisante pour répondre aux exigences de l'unité (refroidissement/chauffage). La température

de fonctionnement doit être maintenue dans l'intervalle spécifié par les spécifications techniques de l'appareil

photo.

This document does not contain any export-controlled information.

Camera Overview

5CP-6408 Range Installation and User Guide - Revision 120 - September 2020

2 Camera Overview

CP-6408 cameras include a 4K visible light camera with 22x (CP-6408-21-I) or 31x (CP-6408-31-I) optical

zoom; audio; digital I/O; near-infrared (NIR) illumination; and automatic side heat sensors. The CP-6408-31-I

also includes laser focus technology (LiDAR) and a camera lens window wiper (wash kit available as an

optional accessory). When the camera is connected to an IP network, it functions as a server, providing

services such as camera control, video streaming, and network communications. The server uses an open,

standards-based communication protocol to communicate with FLIR and third-party video management

system (VMS) clients, including systems that are compatible with ONVIF®. These clients can be used to

control the camera and stream video during day-to-day operations. For a list of supported VMS clients, refer

to the product's web page on FLIR.com.

The video from the camera is viewed by streaming it over an IP network using MJPEG and H.264 encoding.

If help is needed during the installation process, contact the local FLIR service representative or call the

support number that appears on the product's page at https://www.flir.com/support/. All installers and

integrators are encouraged to take advantage of the training offered by FLIR; visit

https://www.flir.com/support-center/training/ for more information.

For safety, and to achieve the highest levels of performance from the camera system, always follow the

warnings and cautions in this manual when handling and operating the camera.

These cameras are Class 1 Laser Products that comply with IEC

60825-1:2014.

Caution

Use of controls or adjustments or performance of procedures other than those specified herein may result

in hazardous radiation exposure.

Attention

L'utilisation des commandes ou reglages ou l'execution des procedures autres que celles specifiees dans

les presents exigences peuvent etre la cause d'une exposition a un rayonnement dangereux.

Warning

Before drilling into surfaces for camera mounting, verify that electrical or other utility service lines are not

present. Serious injury or death may result from failure to heed this warning.

Caution

Except as described in this manual, do not open the camera for any reason. Damage to the camera can

occur as the result of careless handling or electrostatic discharge (ESD). Always handle the camera with

care to avoid damage to electrostatic-sensitive components.

Prior to making any connections, ensure the power supply or circuit breaker is switched off.

Be careful not to leave fingerprints on the camera’s infrared optics.

Operating the camera outside of the specified input voltage range or the specified operating temperature

range can cause permanent damage.

Related Documentation

CP-6408-21-I or CP-6408-31-I Quick Install Guide

This document does not contain any export-controlled information.

Camera Overview

6CP-6408 Range Installation and User Guide - Revision 120 - September 2020

FLIR CGI Interface Description 2.1

Nexus CGI WebSockets Manual

FLIR Sensors SDK Programmer’s Guide

2.1 Accessing Product Information from the FLIR Website

Up-to-date resources for the camera, including the camera’s specifications, the FLIR Discovery Network

Assistant (DNA) software tool, and this installation and user guide, are available from the camera’s product

information and support pages on FLIR.com. Select Products > Security > Visible Security Cameras, and

then click the relevant product.

To access product information from the FLIR website:

1. Open https://www.flir.com/browse/security/visible-security-cameras/ .

Visible Security Cameras Page on FLIR.com

2. Find and click the camera. The camera’s product information page appears.

Quasar 4K IR PTZ (CP-6408-31-I) Camera Product Information Page on FLIR.com

This document does not contain any export-controlled information.

Camera Overview

7CP-6408 Range Installation and User Guide - Revision 120 - September 2020

3. Scroll down to see the camera’s specifications and related documents.

4. Click Go to Product Support to open the camera’s support page.

Quasar 4K IR PTZ Cameras Product Support Page

5. Click the Resources tab.

6. Click the relevant Download link to download the resource you need.

This document does not contain any export-controlled information.

Camera Overview

8CP-6408 Range Installation and User Guide - Revision 120 - September 2020

2.2 Camera Dimensions

CP-6408-21-I

CP-6408-31-I

This document does not contain any export-controlled information.

Installation

9CP-6408 Range Installation and User Guide - Revision 120 - September 2020

3 Installation

This camera can be installed outdoors or indoors.

For outdoor installation, FLIR recommends:

Always using weatherproof equipment, such as boxes, receptacles, connectors, etc.

For electrical wiring, using the properly rated sheathed cables for conditions to which the cable will be

exposed (for example, moisture, heat, UV, physical requirements, etc.).

Planning ahead to determine where to install infrastructure weatherproof equipment. Whenever possible,

ground components to an outdoor ground.

Using best security practices to design and maintain secured camera access, communications

infrastructure, tamper-proof outdoor boxes, etc.

All electrical work must be performed in accordance with local regulatory requirements.

3.1 Supplied Components

The following table shows the items included in the CP-6408 camera kit (not to scale):

CP-6408-21-I

CP-6408-31-I

Camera Body

Camera Body and Pendant Cap

Pendant Cap

Hard Ceiling Mount

M4 Screw with Rubber Gasket

Hard Ceiling Mount

M5 Screw with Rubber Gasket

O-ring

This document does not contain any export-controlled information.

Installation

10CP-6408 Range Installation and User Guide - Revision 120 - September 2020

CP-6408-21-I

CP-6408-31-I

3-Pin 24 VAC Power Terminal Block

14-Pin Alarm/Audio I/O Terminal Block

2-Pin 12 VDC Power Terminal Block

Safety Lanyard

3.2 Site Preparation

There are several requirements that should be properly addressed prior to installation at the site.

The following specifications are requirements for proper installation and operation of the unit:

Ambient Environment Conditions: Avoid positioning the unit near heaters or heating system outputs.

Avoid exposure to direct sunlight. Use proper maintenance to ensure that the unit is free from dust, dirt,

smoke, particles, chemicals, smoke, water or water condensation, and exposure to EMI.

Accessibility: The location used should allow easy access to unit connections and cables.

Safety: Cables and electrical cords should be routed in a manner that prevents safety hazards, such as

from tripping, wire fraying, overheating, etc. Ensure that nothing rests on the unit’s cables or power cords.

Ample Air Circulation: Leave enough space around the unit to allow free air circulation.

Cabling Considerations: Units should be placed in locations that are optimal for the type of video

cabling used between the unit and the cameras and external devices. Using a cable longer than the

manufacturer’s specifications for optimal video signal may result in degradation of color and video

parameters.

Physical Security: The unit provides threat detection for physical security systems. In order to ensure

that the unit cannot be disabled or tampered with, the system should be installed with security measures

regarding physical access by trusted and un-trusted parties.

Network Security: The unit transmits over IP to security personnel for video surveillance. Proper network

security measures should be in place to assure networks remain operating and free from malicious

interference. Install the unit on the backbone of a trusted network.

Electrostatic Safeguards: The unit and other equipment connected to it (relay outputs, alarm inputs,

racks, carpeting, etc.) shall be properly grounded to prevent electrostatic discharge.

The physical installation of the unit is the first phase of making the unit operational in a security plan. The

goal is to physically place the unit, connect it to other devices in the system, and to establish network

connectivity. When finished with the physical installation, complete the second phase of installation, which

is the setup and configuration of the unit.

This document does not contain any export-controlled information.

Installation

11CP-6408 Range Installation and User Guide - Revision 120 - September 2020

3.3 Camera Connections

CP-6408-21-I Connectors

CP-6408-31-I Connectors

CP-6408-21-I

CP-6408-31-I

Connector

Connection

1

N/A

DC12V IN

If using a 12 VDC power supply, connect its wires to the

two-pin terminal block. See pin assignment below.

CP-6408-21-I: Do not use the DC12V IN and AC24V IN

connectors at the same time.

2

LAN

Attach a Cat 5e or Cat 6 cable from the network switch to

the RJ45 LAN connector for a 10/100/1000 Mbps Ethernet

and PoE connection. For information about using PoE, see

Supplying Power to the Camera. Verify that the LAN

connector LEDs are steady green and flashing yellow.

3

AC24V IN

If using a 24 VAC power supply, connect its wires to the

three-pin power terminal block. See pin assignment below.

CP-6408-21-I: Do not use the DC12V IN and AC24V IN

connectors at the same time.

4

1

DEFAULT

To reset factory defaults at any time, press the Default

button for at least 20 seconds.

5

4

14-pin terminal

block

Attach wires from external devices to the 14-pin terminal

block connector for alarm and audio in/out (see diagram and

definitions below).

6

N/A

VIDEO

BNC connector for analog video output.

This document does not contain any export-controlled information.

Installation

12CP-6408 Range Installation and User Guide - Revision 120 - September 2020

14-Pin Terminal Block

Definition

1

Audio-Out

8

CP-6408-21-I:

RS-485 D1

CP-6408-31-I:

Not used

2

Ground (Audio I/O)

9

Alarm-In 4

3

Alarm-Out A1

10

Alarm-In 3

4

Alarm-Out A2

11

Alarm-In 2

5

Alarm-Out B1

12

Alarm-In 1

6

Alarm-Out B2

13

Ground (Alarm I/O)

7

CP-6408-21-I:

RS-485 D+

CP-6408-31-I:

Not used

14

Audio-In

DC12V IN Connector

(CP-6408-21-I)

Definition

1

-12 VDC

2

+24 VDC

AC24V IN Connector

Definition

1

AC 24L

2

Ground

3

AC 24N

Note

The CP-6408-21-I camera features zero downtime (ZDT) power switching. When the DC12V IN and PoE

connections are both used, the camera draws power through the DC connection. If DC power fails, the

camera switches power to the PoE connection until the DC power source is restored.

Warning

This product contains a battery that is soldered to the PCB. There is a risk of explosion if the battery is

replaced by an incorrect type. Do not replace the battery. The battery should be disposed of in

accordance with the battery manufacturer’s instructions.

3.4 Supplying Power to the Camera

The camera can be powered by PoE or an external 12 VDC (CP-6408-21-I only) or 24 VAC power supply

(not included in the camera kit).

If using PoE, make sure the PoE switch or injector is a Power Sourcing Equipment (PSE) device.

If using a PoE-capable network switch, the switch needs to support Universal PoE 60W 4 pair forced

mode. For information regarding recommended switches, contact FLIR Support. Note: The camera does

not support CDP/LLDP.

If using a PoE injector, use a FLIR CP-POE-4P-60W-xx injector or contact FLIR Support for information

about compatible injectors.

If using an external AC or DC (CP-6408-21-I only) power supply, connect the power supply's wires to the

appropriate power terminal block.

This document does not contain any export-controlled information.

Installation

13CP-6408 Range Installation and User Guide - Revision 120 - September 2020

Warnings

Make sure the camera’s power cable is properly connected. All electrical work must be performed in

accordance with local regulatory requirements.

Use a UL Listed Power Adapter that meets LPS (Limited Power Source) requirements.

Note the camera's maximum power consumption:

CP-6408-21-I (12 VDC)

Mode

Current

Idle

0.7021A

Motor + camera on

0.8821A

Cold start only heater (camera off)

1.3423A

IR LED + camera on

1.8023A

IR LED + camera on + motor

2.1512A

IR + heater + camera on

2.6213A

IR + heater + motor + camera on

3.3121A

CP-6408-31-I

24 VAC (W)

LED

-40°C

25°C

60°C

Camera static

Off

N/A

21

On

27

43

PTZ motion

Off

N/A

29

26

On

57

50

49

Maximum, including

wiper and IRCUT

61

52

PoE (W)

LED

-40°C

25°C

60°C

Camera static

Off

N/A

15

On

35

32

PTZ motion

Off

N/A

22

19

On

41

37

39

Maximum, including

wiper and IRCUT

43

39

42

A PoE injector should be connected only to a PoE network inside a building and not routed outside the

building.

If the camera is installed outdoors with an external power supply, the power supply must be installed

with proper weatherproofing.

A qualified service person should install the camera.

This document does not contain any export-controlled information.

Installation

14CP-6408 Range Installation and User Guide - Revision 120 - September 2020

3.5 Waterproofing the Camera

The camera is IP66-rated to prevent water from entering the camera. Nevertheless, water can enter the

camera if it is not installed properly. Please make sure the warnings below are strictly followed when

installing the camera.

1. Place all cables and the adaptor in dry and well-waterproofed environments, e.g. waterproof boxes. This

prevents moisture accumulation inside the camera and moisture penetration into cables.

2. Seal the cable entry hole of

the pendant cap with the

rubber O-ring (supplied with

the camera) and use thread

seal tape to keep water from

entering the camera.

Waterproofing the Pendant Cap

3. While running cables, slightly

bend the cables in a U-shaped

curve to create a low point.

This prevents water from

entering the camera along the

cables from above.

U-Shaped Cable Installation

3.6 Mounting the Camera

The following accessories and adapters are available for mounting the camera:

Wall Mount Bracket CX-ARMX-G3

Wall Mount Bracket with Power Box CX-ELBX-G3

Gooseneck Mount with Power Box CX-GSNK-G3

Corner Adapter CX-CRNR-G3

Pole Adapter CX-POLE-G3

3.6.1 Securing the Camera

When using either Wall Mount Bracket CX-ARMX-G3 or Wall Mount Bracket with Power Box CX-ELBX-G3

with a CP-6302-31-P PTZ or CP-6302-31-I IR PTZ camera, you need to secure the camera using a safety

lanyard.

1. Before attaching the mounting accessory to the mounting surface, attach the safety lanyard to a secure

anchor point on the mounting surface or on the accessory.

This document does not contain any export-controlled information.

Installation

15CP-6408 Range Installation and User Guide - Revision 120 - September 2020

2. Route the lanyard through the mounting accessory and through the pendant cap.

3. Attach the lanyard to the safety ring on the camera.

4. Route the power, Ethernet, and other cables through

the mounting accessory and attach the mounting

accessory to the mounting surface.

5. Route the power, Ethernet, and other cables through

the pendant cap and attach the pendant cap to the

mounting accessory.

6. Connect the cables to the camera.

7. Carefully insert the camera into the pendant cap and rotate the camera until it locks into place (1/3 turn).

Warning:

The metal locking mechanism carries the weight of the camera. If the camera is not locked into place,

it could become loose and fall.

The screw that attaches the pendant cap to the camera needs to line up with one of the corresponding

screw holes on the camera.

Pendant Cap Screw

Pendant Cap Screw Holes on Camera

8. Securely tighten the pendant cap screw into the camera. The screw prevents the camera from rotating.

9. Try to rotate the camera and make sure it is not possible to rotate the camera.

Warning:

If the camera can be rotated, it could become loose and fall.

Page is loading ...

FLIR Quasar User manual

FLIR Quasar User manual

Related papers

Other documents