Alesis HD24XR User manual

Brand: Alesis

Model: HD24XR

Type: User manual

Using the Alesis HD24XR

Berklee College of Music

MP241 Mix 1 /Using Alesis HD24XR Page 1 of 4

Created by JAL 9/3/07

As with all the hardware and software in the MP&E department… Read the manual!

DANGER! DO NOT LIFT THESE HANDLES! Lifting the handle ejects the hard

drive caddy from the drive bay and can seriously damage the drive.

The Song Select Key [SONG SEL] toggles between PROJECT mode and SONG mode.

In PROJECT mode, select 8 TRACK SONGS or 12 TRACK SONGS using the up and

down cursor keys.

In SONG mode, select the song number and title you want to mix using the up and

down cursor keys.

Song Select Key

Up & Down Cursor Keys

Left and Right Cursor Keys

Scroll through a song title using the left and right keys but be careful… watch the

flashing cursor under your selection.

Using the Alesis HD24XR

Berklee College of Music

MP241 Mix 1 /Using Alesis HD24XR Page 2 of 4

Created by JAL 9/3/07

Selecting a Song

1 Push Song

Select until your

in PROJECT mode

2 Select the

Project you need

with the Up &

Down Cursor Keys

3 Push Song

Select again to

enter SONG mode

4 Select a Song

with the Up &

Down Cursor Keys

Locate Points

The HD24 provides 25 programable locate points (0-24) for each song. With “Locate

0” always being the begining of the song. These 25 locate points are stored with

each song and can be given alphanumeric names… see the manual for details. The

first 7 “Locate Points” are available as dedicated keys on the face of the HD24 (0-

6). The remaining 17 points (7-24) are accessable through the alphanumeric display.

An indicator in the lower right hand corner of the display shows the active

“Location Point”.

Pressing any of the 7 keys (Locate 0-6) will cause the HD24 to locate to that key’s

stored address. However, pressing the “Locate” key will take the system to the

address in the active “Locate Point” int the alphanumeric display… In other words…

If you hit key 5 you will got to “Locate Point” 5 but if you hit “LOCATE” with

“Locate Point 14” in the alphanumeric diplay you will go to 14.

Setting locate points can be done with the transport stationary or on the fly using

the “Set Locate” key. Tapping the key will send the current location time to the

NEXT “Location Point”… it actually happens on the release of the key… HOLDING

the “Set Locate” key and tapping one of the 1-6 keys stores that address in that

Using the Alesis HD24XR

Berklee College of Music

MP241 Mix 1 /Using Alesis HD24XR Page 3 of 4

Created by JAL 9/3/07

Setting Location Points

Active or current

“Locate Point”

“Locate 0”

“Set Locate”

Dedicated locate keys

1-6

“LOCATE” key

Looping

Looping cycles the HD24 between any two of the 25 location points… as long as the

“Loop Start” time preceedes the “Loop End” time. Setting the “Loop Start” and

“Loop End” points is done using the alphanumeric display, the “Locate Select” key

and the “Cursor Arrow” keys.

Setting Loop Points

Make the “Location Point” you want to be the “Loop Start” active in

the alphanumeric display by hitting “Locate Select” and scrolling with

the  cursor keys. Next, HOLD “Locate Select” and tap the left

cursor key. A “Start” indicator will turn on in the Locate Pt window. Use the

 cursor keys again to find the “Location Point” you want to use for

the “Loop End”. Next, HOLD “Locate Select” and tap the left  cursor

key. A “End” indicator will turn on in the Locate Pt window.

Activating the Loop

Select “Auto Return” and “Auto Play” to activate the loop cycle.

Using the Alesis HD24XR

Berklee College of Music

MP241 Mix 1 /Using Alesis HD24XR Page 4 of 4

Created by JAL 9/3/07

Making Loops

1. “Locate Select”

to activate

location points in

alphanumeric

display

2. Scroll to “Loop

Start” location

point

3. HOLD “Locate

Select” and hit

left  cursor key

to set “Loop

Start”

4. Look for “Start”

indicator in

location point

window

8. Turn on “Auto Return

9. Turn on “Auto Play”

5. Scroll to “Loop

End” location

point

6. HOLD “Locate

Select” and hit

right  cursor

key to set “Loop

Start”

7. Look for “End”

indicator in

location point

window

Alesis HD24XR User manual

Alesis HD24XR User manual

Related papers

Other documents