Drive Medical Design Mobility Aid CE 1035 FP User manual

Drive Medical Design
Brand
Drive Medical Design
Model
Mobility Aid CE 1035 FP
Category
Rack accessories
Type
User manual

This manual is also suitable for

forearm platform
and mounting bracket
item # CE 1035 FP
for use with all anterior & posterior
wenzelite safety rollers and gait trainers
www.drivemedical.com
EU Authorized Representative
Drive Medical LTD
Ainley’s Industrial Estate
Elland, West Yorkshire,
United Kingdom HX5 9JP
© 2006 Medical Depot, Inc. All rights reserved.
Drive is a trademark of Medical Depot, Inc.
Port Washington N.Y. 11050 USA Made in China
two year limited
warranty
Your Drive brand product is warranted to be free of
defects in materials and workmanship for two years
from the date of the original consumer purchase.
This device was built to exacting standards and
carefully inspected prior to shipment. This Two
Year Limited Warranty is an expression of our
confidence in the materials and workmanship of
our products and our assurance to the consumer of
dependable service.
In the event of a defect covered by this warranty, we
will, at our option, repair or replace the device.
This warranty does not cover device failure due to
owner misuse or negligence, or normal wear and
tear. The warranty does not extend to non-durable
components such as rubber accessories, casters, and
grips, which are subject to normal wear and need
periodic replacement.
If you have a question about your Drive device or
this warranty, please contact an authorized
Drive dealer.
www.drivemedical.com
Mounting Bracket
1. Remove screws (A) from brackets.
2. Mount brackets on handlebar. They can be mounted at
any position along the handlebar and can be mounted
with the opening facing the inside or the outside of
the handlebar.
3. Tighten screws.
NOTE: On Model # CE OBESE XL the mounting brackets
are placed in the center of the handgrips. Cut handgrip
with knife to the size of bracket and then mount the
bracket.
installation
Forearm Platform
Insert vertical handgrip and post (C) into forearm platform
tube (D). Post can be inserted on either side of tube to
allow for additional adjustability.
adjustments
1. Loosen mounting bracket knob (B) and place forearm
platform post into the mounting bracket opening.
2. Rotate forearm platform inward or outward to
appropriate position.
3. Tighten mounting bracket knob (B).
4. Determine forearm platform height by setting collar
(E) at the appropriate height adjustment hole on
the post.
5. Position forearm platform at the height desired.
6. Loosen knob (F) to pronate or supinate the vertical
handgrips. Tighten knob at desired position.
7. Loosen knob (F) to extend or shorten the distance
between the vertical handgrip and the forearm trough.
Tighten knob at desired position.
8. Loosen ratchet handle (G) to adjust angle of vertical
handgrip. Tighten handle at desired position.
9. Secure arm in forearm trough with Velcro strap.
Bracket Mounted Towards Outside
Bracket Mounted Towards Inside
Bracket Mounted on
CE OBESE XL
Bracket Mounted on
Safety Roller
adjustable forearm
platform
installation
Insert vertical handgrip and post (A) into forearm
platform tube (B). Post can be inserted on either
side of tube to allow for additional adjustability.
adjustment
1. Determine forearm platform height by setting
collar (C) at the appropriate height
adjustment hole on the post (Fig 2).
2. Loosen knob (D) to pronate or supinate
the vertical handgrips. Tighten knob at
desired position.
3. Loosen knob (D) to extend or shorten the
distance between the vertical handgrip and
the forearm trough. Tighten knob at desired
position.
4. Loosen ratchet handle (E) to adjust angle of
vertical handgrip. Tighten handle at desired
position.
5. Secure arm in forearm trough with Velcro
strap.
Note: Forearm platforms can only be used with
mounting brackets (CE 1035 S).
B
B
A
C
D
E
C
figure 1
figure 2
C
D
D
adjustable forearm
platform
installation
Insert vertical handgrip and post (A) into forearm
platform tube (B). Post can be inserted on either
side of tube to allow for additional adjustability.
adjustment
1. Determine forearm platform height by setting
collar (C) at the appropriate height
adjustment hole on the post (Fig 2).
2. Loosen knob (D) to pronate or supinate
the vertical handgrips. Tighten knob at
desired position.
3. Loosen knob (D) to extend or shorten the
distance between the vertical handgrip and
the forearm trough. Tighten knob at desired
position.
4. Loosen ratchet handle (E) to adjust angle of
vertical handgrip. Tighten handle at desired
position.
5. Secure arm in forearm trough with Velcro
strap.
Note: Forearm platforms can only be used with
mounting brackets (CE 1035 S).
B
B
A
C
D
E
C
figure 1
figure 2
E
F
G
E
  • Page 1 1
  • Page 2 2

Drive Medical Design Mobility Aid CE 1035 FP User manual

Drive Medical Design
Brand
Drive Medical Design
Model
Mobility Aid CE 1035 FP
Category
Rack accessories
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents