Philips RQ1195/21 User manual

Register your product and get support at

www.philips.com/welcome

Wir helfen Ihnen jederzeit

Gebrauchsanleitung

RQ1195

RQ1175

RQ1155

RQ1151

Page is loading ...

ENGLISH 33

Table of contents

Introduction 34

Important 34

General 34

Jet Clean system (RQ1195 only) 36

Compliance with standards 36

General description 37

The display 38

Charging 38

Battery fully charged 39

Battery low 39

Remaining battery capacity 40

Travel lock 40

Charging 41

Charging in the charger 41

Charging in the Jet Clean System (RQ1195 only) 42

Using the shaver 42

Shaving 42

Using the trimmer (RQ1155/RQ1151 only) 43

Using the Beard Styler attachment (RQ1195, RQ1175

and RQ1155/80 only) 44

Maintenance 47

Cleaning the shaving unit 47

Cleaning the shaving unit in the Jet Clean System

(RQ1195 only) 48

Extra-thorough cleaning method 52

Cleaning the trimmer 54

Cleaning the Beard Styler attachment (RQ1195, RQ1175

and RQ1155/80 only) 54

Storage 54

Replacing the shaving head holder 55

Ordering accessories 56

Environment 56

Removing the rechargeable shaver battery 57

Guarantee and support 57

Guarantee restrictions 57

Troubleshooting 57

Additional information 59

Introduction

Congratulations on your purchase and welcome to Philips! To

fully benet from the support that Philips offers, register your

product at www.philips.com/welcome.

Please read this user manual, as it contains information about

the features of this shaver as well as some tips to make

shaving easier and more enjoyable.

Important

Read this user manual carefully before you use the shaver and

the Jet Clean System and save it for future reference.

Note: In this user manual the term ‘appliances’ refers to the

shaver and the Jet Clean System. If your shaver does not come

with a Jet Clean System, it refers to the shaver only.

General

Danger

- Make sure the adapter does not get wet.

Warning

- The adapter contains a transformer. Do not cut off

the adapter to replace it with another plug, as this causes

a hazardous situation.

- These appliances are not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of these appliances by a person

responsible for their safety.

- Children should be supervised to ensure that they do not

play with the shaver and the Jet Clean System.

- Be careful with hot water when you clean the appliances.

Always check if the water is not too hot, to prevent your

hands from getting burnt.

ENGLISH34

Caution

- Never immerse the Jet Clean System and the charger in

water nor rinse them under the tap.

- The appliances and accessories are not dishwasher-proof.

- Always place and use the appliances on a surface that is

uid-resistant.

- Use, charge and store the shaver at a temperature

between 5°C and 35°C.

- Only use the accessories supplied with this shaver or that

have been specically developed for this shaver.

- If the adapter or any of the other accessories is damaged,

always have it replaced with one of the original type in

order to avoid a hazard.

- The adapter transforms 100-240 volts to a safe low

voltage of less than 24 volts.

- Do not use the appliances and accessories if they are

damaged.

- Water may leak from the socket at the bottom of the

shaver when you rinse it. This is normal and not dangerous

because all electronics are enclosed in a sealed power unit

inside the shaver.

ENGLISH 35

Jet Clean system (RQ1195 only)

Caution

- Only use the Jet Clean System with the original HQ200

cleaning uid.

- Always place and use the Jet Clean System on a stable,

level and horizontal uid-resistant surface to prevent

leakage.

- Never immerse the Jet Clean System in water.

- Empty the cleaning chamber and clean it thoroughly by

rinsing it with hot tap water every 15 days.

- The Jet Clean System thoroughly cleans but does not

disinfect your shaver, therefore do not share the shaver

with others.

- The cleaning chamber of the Jet Clean System is not

dishwasher-proof.

- When the Jet Clean System is ready for use, do not move

it to prevent leakage of cleaning uid.

Compliance with standards

- This shaver complies with the internationally approved

safety regulations and can be safely used in the bath or

shower and cleaned under the tap.

- These Philips appliances comply with all standards

regarding electromagnetic elds (EMF). If handled properly

and according to the instructions in this user manual, the

appliances are safe to use based on scientic evidence

available today.

ENGLISH36

General description (Fig. 3)

A Shaver

1 Display

2 Shaver on/off button

3 Protection cap

4 RQ11 Shaving unit

B CRP331 Trimmer

(RQ1155/16 and RQ1151 only)

C RQ111 Beard Styler attachment

(RQ1195, RQ1175

and RQ1155/80 only)

5 Hair length selector

6 Comb of Bread styler attachment

D Jet Clean System (RQ1195 only)

7 Shaver holder

8 ’Cleaning chamber empty’ symbol

9 Cleaning symbol

10 Drying symbol

11 Jet Clean System on/off button

12 Cleaning chamber release button

E Adapter

F Foldable charger

G Cleaning brush

H HQ200 Cleaning uid

(RQ1195 only)

I Pouch

ENGLISH 37

The display

Note: If there is a protective foil on the display, remove it before

you use the shaver for the rst time.

The various shaver types have different displays, which are

shown in the gures below.

- RQ1195/RQ1175

- RQ1155/RQ1151

Charging

- Charging takes approx. 1 hour.

RQ1195/RQ1175

- When the shaver is charging, rst the bottom charging

light ashes, then the second charging light, and so on until

the shaver is fully charged.

- Quick charge: When the shaver contains enough energy

for one shave, the bottom charging light alternately ashes

orange and white.

RQ1155/RQ1151

Note: The displays of the various shaver types look different, but

work in the same way.

- When the shaver is charging, rst the plug symbol and the

battery symbol ash alternately. After some time, the plug

symbol goes out and the battery symbol continues to

ash until the shaver is fully charged.

- Quick charge: When the shaver contains enough energy

for one shave, the alternate ashing of the plug symbol

and battery symbol stops and only the battery symbol

ashes.

ENGLISH38

Battery fully charged

RQ1195/RQ1175

- When the battery is fully charged, all charging lights light

up continuously. After approx. 30 minutes, the display

automatically switches off again.

RQ1155/RQ1151

Note: The displays of the various shaver types look different, but

work in the same way.

- When the battery is fully charged, the battery symbol

lights up continuously. After approx. 30 minutes, the display

automatically switches off again.

Battery low

RQ1195/RQ1175

- When the battery is almost empty (when there are only

5 or fewer shaving minutes left), the bottom charging light

ashes orange.

- When you switch off the shaver, the bottom charging light

continues to ash for a few seconds.

RQ1155/RQ1151

Note: The displays of the various shaver types look different, but

work in the same way.

- When the battery is almost empty (when there are only

5 or fewer shaving minutes left), the plug symbol ashes.

- When you switch off the shaver, the plug

symbol continues to ash for a few seconds.

ENGLISH 39

Remaining battery capacity

RQ1195/RQ1175

- The remaining battery capacity is indicated by the number

of charging lights that are on.

Travel lock

You can lock the shaver when you are going to travel.

The travel lock prevents the shaver from being switched

on by accident.

Activating the travel lock

1 Press the on/off button for 3 seconds to enter the travel

lock mode.

, The lock symbol lights up on the display.

Note: The displays of the various shaver types look different, but

show the same symbol.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

, The motor starts running to indicate that the travel lock

has been deactivated.

The shaver is now ready for use again.

Note: When you place the shaver in the plugged-in charger or Jet

Clean System, the travel lock is automatically deactivated.

ENGLISH40

Charging

Charging takes approx. 1 hour.

RQ1195/RQ1175: A fully charged shaver has a shaving time

of up to 50 minutes or 15 days.

RQ1155/RQ1151: A fully charged shaver has a shaving time

of up to 40 minutes or 12 days.

Charge the shaver before you use it for the rst time and

when the display indicates that the battery is almost empty

(see section ‘Battery low’ in chapter ‘The display’).

Quick charge

After the shaver has charged for 5 minutes, it contains

enough energy for one shave.

Charging in the charger

1 Insert the small plug into the charger.

2 Unfold the charger (‘click’).

3 Put the adapter in the wall socket.

4 Put the shaver in the charger (1) and press it backwards

until it locks into place (2).

, The display shows that the shaver is charging (see

section ‘Charging’ in chapter ‘The display’).

ENGLISH 41

Charging in the Jet Clean System (RQ1195 only)

1 Put the small plug in the Jet Clean System.

2 Put the adapter in the wall socket.

3 Hold the shaver upside down above the holder with the

back of the shaver pointing towards the holder.

Note: RQ1180 only: when you turn the shaver upside down, the

battery indication on the display is also turned upside down so

you can still see to what level the battery is charged.

4 Place the shaver body in the holder behind the two clips

(1) and press it down until it locks into place (2).

Note: The shaver cannot be placed in the Jet Clean System when

the protection cap is on the shaving unit or when the trimmer is

placed on the shaver.

, The display shows that the shaver is charging (see

chapter ‘The display’).

Using the shaver

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you expect and

your skin may even become slightly irritated. This is normal.

Your skin and beard need time to adapt to any new shaving

system.

We advise you to shave regularly (at least 3 times a week)

for a period of 3 weeks to allow your skin to adapt to the

new shaver. During this period, use your new electric shaver

exclusively and do not use other shaving methods. If you use

different shaving methods, it is more difcult for your skin to

adapt to the new shaving system.

1 Press the on/off button once to switch on the shaver.

, RQ1195/RQ1175: The display lights up for a few

seconds.

ENGLISH42

2 Move the shaving heads over your skin in circular

movements.

- Do not make straight movements.

3 Press the on/off button once to switch off the shaver.

, RQ1195/RQ1175: The display lights up for a few seconds

and then shows the remaining battery capacity.

Wet shaving

You can also use this shaver on a wet face with shaving foam

or shaving gel.

To shave with shaving foam or shaving gel, follow the steps

below:

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel to your skin.

3 Rinse the shaving unit under the tap to ensure that the

shaving unit glides smoothly over your skin.

4 Press the on/off button once to switch on the shaver.

5 Move the shaving heads over your skin in circular

movements.

Note: Rinse the shaver under the tap regularly to ensure that it

continues to glide smoothly over your skin.

6 Dry your face and thoroughly clean the shaver after use

(see chapter ‘Cleaning and maintenance’).

Note: Make sure you rinse all foam or shaving gel off the shaver.

Using the trimmer (RQ1155/RQ1151 only)

You can use the trimmer to groom your sideburns and

moustache.

1 Pull the shaving unit straight off the shaver.

Note: Do not twist the shaving unit while you pull it off the

shaver.

ENGLISH 43

2 Insert the lug of the trimmer into the slot in the top

of the shaver (1). Then press down the trimmer (2) to

attach it to the shaver (‘click’).

3 Press the on/off button once to switch on the trimmer.

4 You can now start trimming.

5 Press the on/off button once to switch off the trimmer.

6 Pull the trimmer straight off the shaver.

Note: Do not twist the trimming unit while you pull it off the

shaver.

7 Insert the lug of the shaving unit into the slot in the top

of the shaver (1). Then press down the shaving unit (2)

to attach it to the shaver (‘click’).

Using the Beard Styler attachment

(RQ1195,RQ1175 and RQ1155/80 only)

Note: Only use the Beard Styler attachment to trim facial hair

(beard, moustache and sideburns). Do not use it to trim body

parts below the neckline.

1 Make sure the shaver is switched off.

2 Pull the shaving unit straight off the shaver.

Note: Do not twist the shaving unit while you pull it off the

shaver.

ENGLISH44

3 Insert the lug of the Beard Styler attachment into the

slot in the top of the shaver (1). Then press down the

Beard Styler attachment (2) to attach it to the shaver

(‘click’).

Using the Beard Styler attachment with comb

You can use the Beard Styler attachment with the comb

attached to style your beard at one xed setting, but also at

different length settings. The hair length settings on the Beard

Styler attachment correspond to the remaining hair length

after cutting and range from 1 to 5mm.

1 Slide the comb straight into the guiding grooves on both

sides of the Beard Styler attachment (‘click’).

2 Press the length selector (1) and then push it to the left

or right (2) to select the desired hair length setting.

3 Press the on/off button on the shaver to switch it on.

4 You can now start styling your beard.

ENGLISH 45

Using the Beard Styler attachment without comb

You can use the Beard Styler attachment without the comb

to trim and contour your beard, moustache or sideburns.

1 Pull the comb off the Beard Styler attachment.

Note: Grab the comb in the centre to pull it off the Beard Styler

attachment. Do not pull at the sides of the comb.

2 Press the on/off button to switch on the shaver.

3 You can now start to trim and contour your beard,

moustache, sideburns or neckline.

Beard styles

Below you nd some examples of beard styles you

can create.

- A stubble look

- A full beard

ENGLISH46

- A moustache

- A goatee

Maintenance

Never use scouring pads, abrasive cleaning agents or aggressive

liquids such as petrol or acetone to clean the shaver, its

accessories and the Jet Clean System (RQ1195 only).

- The best and most hygienic way to clean the shaver is in

the Jet Clean System. You can also rinse the shaver under

the tap or clean it with the brush supplied.

- Clean the shaver after every shave for optimal shaving

performance.

- You can clean the outside of the shaver with a damp cloth.

- Regular cleaning guarantees better shaving performance.

Cleaning the shaving unit

Be careful with hot water. Always check if the water is not

too hot, to prevent your hands from getting burnt.

1 Switch off the shaver. Remove it from the charger

or remove it from the Jet Clean System (RQ1195 only).

2 Rinse the shaving unit under a hot tap for some time.

Note: You can also clean the shaving unit with the cleaning brush

supplied.

ENGLISH 47

3 Pull the shaving head holder off the bottom part of the

shaving unit and rinse it under a hot tap for 30 seconds.

Note: You can also clean the shaving head holder with the

cleaning brush supplied.

4 Carefully shake off excess water and let the shaving

head holder dry.

Never dry the shaving unit with a towel or tissue, as this

may damage the shaving heads.

5 Reattach the shaving head holder to the bottom part of

the shaving unit (‘click’).

Cleaning the shaving unit in the Jet Clean System

(RQ1195 only)

The Jet Clean System has an automatic cleaning program.

When you press the on/off button, the Jet Clean System

starts cleaning in this automatic cleaning program.

Preparing the Jet Clean System for use

Fill the cleaning chamber before rst use.

1 Put the small plug in the Jet Clean System.

2 Put the adapter in the wall socket.

, The holder automatically moves to the highest position.

3 Simultaneously press the release buttons on both sides

of the cleaning chamber (1). Then lift the Jet Clean

System off the cleaning chamber (2).

, The cleaning chamber remains behind.

ENGLISH48

4 Fill the cleaning chamber with HQ200 cleaning uid to a

level between the two lines.

5 Place the Jet Clean System back onto the cleaning

chamber.

Make sure the release buttons click back into place.

Using the Jet Clean System

Note: If you use the shaver with shaving foam or shaving gel, we

advise you to rinse it under the hot tap before you clean it in

the Jet Clean System. This guarantees an optimal lifetime for the

cleaning uid.

1 Hold the shaver upside down above the holder with the

back of the shaver pointing towards the holder.

2 Place the shaver body in the holder behind the two clips

(1) and press it down until it locks into place (2).

, The display shows that the shaver is charging (see

chapter ‘The display’).

3 Press the on/off button on the Jet Clean System to start

the cleaning program.

, The shaver display stops showing the charging indication.

ENGLISH 49

, The cleaning light starts to ash and the shaver is

automatically lowered into the cleaning uid.

, The cleaning light ashes throughout the cleaning

program, which takes a few minutes.

, During the rst phase of the cleaning program, the

shaver automatically switches on and off several times

and moves up and down.

, During the second phase of the cleaning program, the

shaver is placed in the drying position, indicated by the

ashing drying symbol. This phase takes approx. 2 hours.

The shaver stays in this position until the end of the

program.

, After the cleaning program, the charging indication

appears on the shaver display (see chapter ‘The display’).

Note: If you press the on/off button of the Jet Clean System

during the cleaning program, the program aborts. In this case,

the cleaning or drying light stops ashing and the holder moves

to the highest position.

Note: If you remove the adapter from the wall socket during the

cleaning program, the program aborts. The holder remains in its

current position. When you put the adapter back into the wall

socket, the holder moves to the highest position.

- When the cleaning uid drops below the minimum level,

the ‘cleaning chamber empty’ symbol starts to ash and

the holder returns to its starting position.

- If you use the Jet Clean System to clean your shaver every

day, you need to rell the cleaning chamber approx. every

15 days.

Cleaning the Jet Clean System

Clean the cleaning chamber every 15 days.

You can wipe the outside of the Jet Clean System with a

damp cloth.

1 Simultaneously press the release buttons on both sides

of the Jet Clean System (1). Then lift the Jet Clean

System off the cleaning chamber (2).

, The cleaning chamber remains behind.

ENGLISH50

2 Pour any remaining cleaning uid out of the cleaning

chamber.

You can simply pour the cleaning uid down the sink.

3 Rinse the cleaning chamber under the tap.

The cleaning chamber is not dishwasher-proof.

4 Fill the cleaning chamber with HQ200 cleaning uid to a

level between the two lines.

5 Place the Jet Clean System back onto the cleaning

chamber.

Make sure the release buttons click back into place.

ENGLISH 51

Page is loading ...

Philips RQ1195/21 User manual

Related papers

Other documents