Robot Coupe R 15 Operating Instructions Manual

Brand: Robot Coupe

Model: R 15

Category: Small kitchen appliances

Type: Operating Instructions Manual

This manual is also suitable for

Robot Coupe R 15 is a versatile food processor designed to handle various tasks in a commercial kitchen. It features a powerful motor and a range of attachments for chopping, slicing, grating, emulsifying, and mixing. The device is known for its efficiency, precision, and durability, making it suitable for preparing large quantities of food quickly and consistently. It also ensures safety with its locking and safety systems.

R 8

R 10

R 15

R 20

Robot-coupe USA. Inc.

P.O. Box 16625, Jackson, MS 39236-6625 - 264 South Perkins St., Ridgeland, MS 39157

e-mail: [email protected] - website: www.robotcoupeusa.com - Phone : 1-800-824-1646

UNPACKING

s#AREFULLYREMOVETHEEQUIPMENTFROMTHEPACKAGING

and take out all the boxes or packets containing

attachments or speciﬁc items.

s7!2.).'SOMEOFTHETOOLSAREVERYSHARPEG

blades, discs... etc.

s 3TORE MANUALS TOOLS AND SPARE PARTS IN A SAFE

PLACEAVAILABLETOTHEUSERSOFTHEMACHINE

INSTALLATION

s )NSTALL THE MACHINE ON A CLEAR mOOR SPACE WITH

SUFlCIENT ROOM TO SAFELY OPERATE AND CLEAN THE

machine.

CONNECTION

s!LWAYSCHECKTHATYOURPOWERSUPPLYCORRESPONDS

to that indicated on the identiﬁcation plate on the

motor unit and that it can withstand the amperage.

s4HEMACHINEMUSTBEGROUNDED

s !LWAYS CHECK THAT THE MOTOR SHAFT ROTATES IN

anticlockwise direction before the blades are

installed.

HANDLING

s !LWAYS TAKE CARE WHEN HANDLING THE BLADES AS

THEYAREEXTREMELYSHARP

s7EARCUTPROOFGLOVESWHENHANDLINGTHEBLADES

IMPORTANT WARNING

ASSEMBLY PROCEDURES

s&OLLOWTHEVARIOUSASSEMBLYPROCEDURESCAREFULLY

(see page 6) and make sure that all the attachments

ARECORRECTLYPOSITIONED

USE

s .EVER TRY TO OVERRIDE THE LOCKING AND SAFETY

SYSTEMS

s.EVERINSERTANYOBJECTINTOTHECONTAINERWHERE

the food is being processed.

s.EVERPUSHTHEINGREDIENTSDOWNWITHYOURHAND

s$ONOTOVERLOADTHEAPPLIANCE

s-AXIMUMlLLLEVELIS

full, less if the product is

VERYDENSEORSTICKY

CLEANING

s !S A PRECAUTION ALWAYSUNPLUG YOUR APPLIANCE

before cleaning it.

s!LWAYSCLEANTHEAPPLIANCEANDITSATTACHMENTSAT

THEENDOFEACHCYCLE

s.EVERIMMERSETHEMOTORUNITINWATER

s &OR PARTS MADE FROM ALUMINUM USE METAL SAFE

detergents intended for aluminum.

s#AUSTICDETERGENTSUSEDINAUTOMATICDISHWASHERS

QUICKLY DEGRADE PLASTIC PARTS  (AND WASH PLASTIC

parts if possible.

s2OBOT#OUPECANINNOWAYBEHELDRESPONSIBLEFOR

the user’s failure to follow the basic rules of cleaning

ANDHYGIENE

MAINTENANCE

s $O NOT OPEN THE MOTOR HOUSING 4HERE ARE NO

USER SERVICEABLE COMPONENTS INSIDE THE ELECTRICAL

HOUSING2EFERCONTROLCOMPONENTREPAIRSTOQUALIlED

technicians.

s 2EMOVE AND CLEAN SHAFT SEALS MONTHLY 2EPLACE

seals each 3 to 6 months. Lubricate with food safe

grease.

s)TISPARTICULARLYIMPORTANTTOMAINTAINANDCHECK

the attachments since certain ingredients contain

CORROSIVEAGENTSEGCITRICACID

s.EVEROPERATETHEAPPLIANCEIFTHEPOWERCORDOR

plug has been damaged or if the appliance fails to

WORKPROPERLYORHASBEENDAMAGEDINANYWAY

s)FTHEMACHINEMALFUNCTIONSINANYWAYDISCARDANY

FOODBEINGPROCESSEDANDREFERSERVICETOQUALIlED

maintenance technicians.

WARNING: In order to limit accidents such as electric shocks or personal injury, and in order to limit material damage due to misuse

of the appliance, please read these instructions carefully and follow them strictly. Reading the operating instructions will help you get

to know your appliance and enable you to use the equipment correctly. Please read these instructions in their entirety and make sure

that anyone else who may use the appliance also reads them beforehand.

WARNING

Keep these instructions in

a safe place

OPERATING INSTRUCTIONS

We reserve the right to alter at any time without notice the technical speciﬁcations of this appliance.

None of the information contained in this document is of a contractual nature. Modiﬁcations may be made at any time.

SUMMARY

WARRANTY

IMPORTANT WARNING

INTRODUCTION TO YOUR NEW

2s2s2s2

CUTTER MIXER

SWITCHING ON THE MACHINE

s!DVICEONELECTRICALCONNECTIONS

s#ONTROLPANEL

ASSEMBLY

s Machine

s Blade

USES AND EXAMPLES

OPTIONS

s Stainless-steel mini bowl

s3ERRATEDBLADE&INESERRATEDBLADE

s Vacuum kit R-Vac

CLEANING

MAINTENANCE

s$ISMANTLINGTHEBLADEASSEMBLY

s Blade

s Seal

s Lid seal

OPERATING INSTRUCTIONS FOR

THE VACUUM KIT R-VAC

DIAGNOSTIC SYSTEM

FITTING AND USING THE BLADE ASSEMBLY

sBLADEASSEMBLY

sBLADEASSEMBLY

TECHNICAL SPECIFICATIONS

s7EIGHT

s$IMENSIONS

s7ORKINGSPACE

s.OISELEVEL

s Electrical data

SAFETY

SERVICE

TECHNICAL DATA

s%XPLODEDVIEWS

s Electrical and wiring diagrams

ROBOT-COUPE U.S.A., INC. LIMITED WARRAN TY

YOUR NEW ROBOT COUPE PRODUCT

IS WARRANTED TO THE ORIGINAL

PURCHASER FOR A PERIOD OF

ONE YEAR FROM THE DATE OF

PURCHASE.

This LIMITED WARRANTY is against

defects in the material and/or

workmanship, and includes labor

for replacement of defective parts,

provided repairs are performed by

an authorized service agency (see

attached list).

The Customer must inform the

Service Agency of the possibility of

warranty coverage and provide a

copy of the dated sales or delivery

receipt BEFORE WARRANTY REPAIRS

ARE BEGUN.

Replacement parts and accessories

AREWARRANTED FORNINETY  DAYS

from the date of purchase when

purchased separately and will be

veriﬁed by dated sales receipt OR

packing slip which lists that item.

All parts or accessories replaced

under warranty must be returned to

the Service Agency.

7 - 4HECOSTOF CHANGINGDIRECTIONOFROTATIONOF

THREEPHASEELECTRICMOTORS)NSTALLERISRESPONSIBLE

8 - 3()00).' $!-!'%3 6ISIBLE ANDOR

HIDDENDAMAGEISTHERESPONSIBILITYOFTHEFREIGHT

CARRIER4HECONSIGNEEMUSTINFORMTHECARRIERAND

CONSIGNORIMMEDIATELYORUPONDISCOVERYINTHE

case of hidden defects.

+%%0 !,, /2)').!, #/.4!).%23 !.$

0!#+).'-!4%2)!,3&/2#!22)%2).30%#4)/.

.EITHER 2/"/4#/50% 53! ).# NOR ITS

AFlLIATED COMPANIES OR ANY OF ITS DISTRIBUTORS

DIRECTORSAGENTSEMPLOYEESORINSURERSWILLBE

liable for indirect damage, losses, or expenses

LINKEDTOTHEAPPLIANCEORTHEINABILITYTOUSEIT

The ROBOT-COUPE U.S.A., INC. warranty is

given expressly and in lieu of all other warranties,

expressed or implied, for merchantability and

for ﬁtness toward a particular purpose and

constitutes the only warranty made by ROBOT-

COUPE U.S.A., INC.

THE FOLLOWING ARE NOT

COVERED BY THE ROBOT-COUPE

U.S.A. INC LIMITED WARRANTY:



$AMAGECAUSEDBYABUSEMISUSEDROPPING

OROTHERSIMILAR DAMAGECAUSEDBY ORRESULTING

FROMFAILURETOFOLLOWASSEMBLYOPERATINGCLEA-

ning, user maintenance or storage instructions.

 Labor to sharpen and/or replacements for

BLADESTHATHAVEBECOMEBLUNTCHIPPEDORWORN

AFTERANORMALOREXCESSIVEPERIODOFUSE

3 - Materials or labor to replace or repair

scratched, stained, chipped, pitted, dented or

DISCOLOREDSURFACES BLADES KNIVES ATTACHMENTS

or accessories.

4 - !NY ALTERATION ADDITION OR REPAIR THAT

HASNOTBEENCARRIEDOUTBYTHECOMPANYORAN

APPROVEDSERVICEAGENCY

 4RANSPORTATIONOFTHEAPPLIANCETOORFROMAN

APPROVEDSERVICEAGENCY

6 - Labor charges to install or test new

attachments or accessories (i.e., bowls, plates,

BLADESATTACHMENTSWHICHHAVEBEENREPLACED

FORANYREASON

UNPACKING

s#AREFULLYREMOVETHEEQUIPMENTFROMTHEPACKAGING

and take out all the boxes or packets containing

attachments or speciﬁc items.

s7!2.).'SOMEOFTHETOOLSAREVERYSHARPEG

blades, discs... etc.

s 3TORE MANUALS TOOLS AND SPARE PARTS IN A SAFE

PLACEAVAILABLETOTHEUSERSOFTHEMACHINE

INSTALLATION

s )NSTALL THE MACHINE ON A CLEAR mOOR SPACE WITH

SUFlCIENT ROOM TO SAFELY OPERATE AND CLEAN THE

machine.

CONNECTION

s!LWAYSCHECKTHATYOURPOWERSUPPLYCORRESPONDS

to that indicated on the identiﬁcation plate on the

motor unit and that it can withstand the amperage.

s4HEMACHINEMUSTBEGROUNDED

s !LWAYS CHECK THAT THE MOTOR SHAFT ROTATES IN

anticlockwise direction before the blades are

installed.

HANDLING

s !LWAYS TAKE CARE WHEN HANDLING THE BLADES AS

THEYAREEXTREMELYSHARP

s7EARCUTPROOFGLOVESWHENHANDLINGTHEBLADES

IMPORTANT WARNING

ASSEMBLY PROCEDURES

s&OLLOWTHEVARIOUSASSEMBLYPROCEDURESCAREFULLY

(see page 6) and make sure that all the attachments

ARECORRECTLYPOSITIONED

USE

s .EVER TRY TO OVERRIDE THE LOCKING AND SAFETY

SYSTEMS

s.EVERINSERTANYOBJECTINTOTHECONTAINERWHERE

the food is being processed.

s.EVERPUSHTHEINGREDIENTSDOWNWITHYOURHAND

s$ONOTOVERLOADTHEAPPLIANCE

s-AXIMUMlLLLEVELIS

full, less if the product is

VERYDENSEORSTICKY

CLEANING

s !S A PRECAUTION ALWAYSUNPLUG YOUR APPLIANCE

before cleaning it.

s!LWAYSCLEANTHEAPPLIANCEANDITSATTACHMENTSAT

THEENDOFEACHCYCLE

s.EVERIMMERSETHEMOTORUNITINWATER

s &OR PARTS MADE FROM ALUMINUM USE METAL SAFE

detergents intended for aluminum.

s#AUSTICDETERGENTSUSEDINAUTOMATICDISHWASHERS

QUICKLY DEGRADE PLASTIC PARTS  (AND WASH PLASTIC

parts if possible.

s2OBOT#OUPECANINNOWAYBEHELDRESPONSIBLEFOR

the user’s failure to follow the basic rules of cleaning

ANDHYGIENE

MAINTENANCE

s $O NOT OPEN THE MOTOR HOUSING 4HERE ARE NO

USER SERVICEABLE COMPONENTS INSIDE THE ELECTRICAL

HOUSING2EFERCONTROLCOMPONENTREPAIRSTOQUALIlED

technicians.

s 2EMOVE AND CLEAN SHAFT SEALS MONTHLY 2EPLACE

seals each 3 to 6 months. Lubricate with food safe

grease.

s)TISPARTICULARLYIMPORTANTTOMAINTAINANDCHECK

the attachments since certain ingredients contain

CORROSIVEAGENTSEGCITRICACID

s.EVEROPERATETHEAPPLIANCEIFTHEPOWERCORDOR

plug has been damaged or if the appliance fails to

WORKPROPERLYORHASBEENDAMAGEDINANYWAY

s)FTHEMACHINEMALFUNCTIONSINANYWAYDISCARDANY

FOODBEINGPROCESSEDANDREFERSERVICETOQUALIlED

maintenance technicians.

WARNING: In order to limit accidents such as electric shocks or personal injury, and in order to limit material damage due to misuse

of the appliance, please read these instructions carefully and follow them strictly. Reading the operating instructions will help you get

to know your appliance and enable you to use the equipment correctly. Please read these instructions in their entirety and make sure

that anyone else who may use the appliance also reads them beforehand.

WARNING

Keep these instructions in

a safe place

INTRODUCTION TO YOUR

.%72s2s2s2

CUTTER MIXER

4HE #UTTER IS PERFECTLY GEARED TO PROFESSIONAL

REQUIREMENTS)TWILLPERFORMANYNUMBEROFTASKSAS

YOUWILLDISCOVERWITHUSE

)TCANBEUSEDFORPROCESSINGMEATANDVEGETABLES

ﬁne stufﬁng, mousse, grinding, kneading and

MIXINGxALLINSECONDS)TSOUTSTANDINGRESULTSWILL

SOONINTRODUCEYOUTOAWHOLENEWWORLDOFCULINARY

skills.

)TS SIMPLE DESIGN MEANS THAT ALL PARTS WHICH ARE

HANDLED FREQUENTLY CAN BE EASILY ASSEMBLED OR

REMOVEDFORMAINTENANCEORCLEANING

4OMAKETHINGSEASIERFORYOUTHISINSTRUCTIONSMANUAL

HASBEENDIVIDEDACCORDINGTOTHEVARIOUSASSEMBLY

operations.

This manual contains vital information designed to

help the user get the most out of his or her cutter

mixer.

#ONSEQUENTLY WE STRONGLY ADVISE YOU TO READ THE

MANUAL CAREFULLY BEFORE USING YOUR MACHINE 7E

HAVEALSOINCLUDEDAFEWEXAMPLESTOHELPYOUGET

THE FEEL OF YOUR NEW MACHINE AND APPRECIATE ITS

COUNTLESSADVANTAGES

SWITCHING ON

THE MACHINE

s!$6)#%/.%,%#42)#!,#/..%#4)/.

"EFORE PLUGGING IN CHECK THAT YOUR POWER SUPPLY

corresponds to that indicated on the machine rating

plate.

4HREEPHASE2s2s2s2

4HESEMODELSMUSTBEPOWEREDFROMA6

(ZPHASEELECTRICALSUPPLY

4HEMACHINEISSUPPLIEDWITHAPOWERCORDANDAPLUG

ATTACHMENT)FWIRINGTOASERVICEDISCONNECTBOXTHIS

SHOULDBEUNDERTAKENBYAQUALIlEDELECTRICIAN

4HEPOWERCORDHASFOURWIRESONEGROUNDEDWIRE

plus three phase wires.

#ONNECTTHEGREENWIRETOTHEGROUNDTERMINALPIN

These machines do not require a neutral

connection.

s#/.42/,0!.%,

2s2s2s2

Red button = ”Off”

'REENBUTTON)

= “On” Low speed

'REENBUTTON))

  h/Nv(IGHSPEED

Black button

= pulse control

'REENINDICATOR  -ACHINESTATUSINDICATOR

ASSEMBLY

s-!#().%

 7ITH THE MOTOR BASE

FACING YOU POSITION THE

bowl on the motor shaft

SOTHATTHEHANDLEONYOUR

left is near the control

panel.

2) Pressing down on the

handles, turn the bowl

lRMLYINANANTICLOCKWISE

direction until it locks into

place.

3) Position the blade

mounted on the motor

SHAFT 4HEN ROTATE IT SO

that it is lowered right

down to the bottom of the

bowl.

!LWAYSCHECKTHATTHEBLADE

IS CORRECTLY POSITIONED AT

the bottom of the bowl

before adding the ingre-

dients to be processed.

WARNING

THIS APPLIANCE MUST BE PLUGGED INTO AN GROUNDED

SOCKET (RISK OF ELECTROCUTION).

s)FTHELIDPARTSAREALREADYASSEMBLED

0LACE THELIDASSEMBLY

in the correct position.

.EXTINSERTTHEMETALPIN

as far as it will go.

s)FTHELIDPARTSHAVENOTBEENASSEMBLED

0OSITIONTHEENDOFTHELIDARMINTHEHINGE.EXT

insert the metal pin as far as it will go (photo



Push the lid guide through the lid arm hole and screw

the cone into the top of the guide (photo



#LIPTHE

lid onto the guide and turn it so that the dimples are

beneath the lid arm (photo

 #LOSE THE LID BY

securing the locking hook

to the edge of the bowl

and pushing the handle

down.

4HEMACHINEISNOWREADY

for operation.

4HE GREEN INDICATOR LIGHT

should be on.

sBLADESEEDIAGRAMPAGE

&OR lNE STUFlNG MOUSSE AND EMULSIONS USE THE

smooth blades.

4HERESHOULDNOTBEANYSPACERBETWEENTHEBASEOFTHE

blade support and the lower blade.

9OUMUSTALWAYSINSERTTHESMALLSPACERBETWEENTHE

blade support base and the lower blade (regular

BASE ASSEMBLY BEFORE CARRYINGOUT MINCING TASKS

)NORDERTOCONTROLTHEMINCINGPROCESSANDPREVENT

THEMEATFROMOVERHEATINGALWAYSUSETHEiPULSEw

BUTTONCOARSEMINCINGASSEMBLY

&ORGRINDINGORKNEADINGUSESERRATEDBLADESANDDO

NOTlT ANYSPACERBETWEENTHELOWERBLADEANDTHE

blade support base.

5SElNESERRATEDBLADESTOCHOPPARSLEYANDDONOT

INSERTANYSPACERBETWEENTHEBLADESUPPORTBASEAND

the lower blade.

  3

WARNING

There is a green status indicator light on the

control panel of the motor unit. If this green light

does not come on, consult the relevant paragraph.

A ﬂashing green light means that the conditions

for the operation have not all been met. Check

that the bowl, lid arm and lid are all correctly

positioned. As soon as the light stops ﬂashing

and stays on, you can use your machine.

USES AND EXAMPLE

USES

Max processing quantity (in pounds)

Speed

R 8 R 10 R 15 R 20

CHOP

s-%!4

Hamburger/ steak tartare 6

Low

Sausage meat / tomatoes 6

Low

Terrine / pâté 4

22 Low

White pudding / liver mousse 8

11 19

High

Galantine (stuffing + thin slices) 4

22 High

s&)3(

Brandade / quenelle 8

11 15

High

Terrines 8

11 19

High

s6%'%4!",%3

Garlic / parsley / onÚn / shallots

High

Soup / vegetable purées 8

11 19

Low

s&25)4

Compotes / fruit purée 8

11 19

Low

EMULSIFY

Mayonnaise / aŠloli 8

11 19

High

Rémoulade sauce 8

11 19

Low

SnaŠ / salmon butter 4

11 15

Low

KNEAD

Shortcrust pastry / shortbread 8

11 15

High

Flaky pastry 8

11 15

Low

BrÚche + Raisin dough 8

11 15

Low

GRIND

Almond paste / nuts 4

11 13

Low

Seafood / ice cubes 4

Low

Breadcrumbs 4

11 13

Low

4HECUTTERMIXERHASNUMEROUSOTHERAPPLICATIONSTHE

ABOVEEXAMPLESAREGIVENFORGUIDANCEANDMAYVARY

ACCORDINGTOTHEQUALITYOFINGREDIENTSORRECIPES

OPERATION

Because of the special bowl and blade design of the

2OBOT#OUPE6ERTICAL#UTTER-IXERSMOSTOPERATIONS

ARECOMPLETEDINAMATTEROFSECONDS4HEOPERATOR

SHOULDPAY CLOSEATTENTION TOTHE PRODUCTAS WELLAS

THEAMOUNTOFTIME REQUIREDTOPROCESS/PERATIONS

SHOULDBERUNON,OWSPEEDUSING(IGHSPEEDONLY

WHENANEXTREMELYlNEPUREECONSISTENCYISDESIRED

4HEREARETWOWAYSTORUNYOURUNIT&IRSTOFALLYOU

MAY RUN THE UNIT CONTINUOUSLY BY lLLING THE BOWL

WITHFOODANDSIMPLYLETTINGITRUNUNTILTHEDESIRED

CONSISTENCY HAS BEEN REACHED 5SE THIS METHOD TO

GRINDMIXBLENDPUREEOREMULSIFY3ECONDLYYOU

MAYCHOPWITHYOURUNITBYPULSINGTHEMACHINE

#UTROUNDPRODUCTSINTOHALVESORQUARTERSANDPREP

LONGVEGETABLESINTOTOINCHPIECES0LACETHESE

into the bowl, and using Low speed, pulse the unit on

ANDOFFQUICKLY5SUALLYTOPULSESYIELDSANEVENLY

mixed chopped substance.

TO CHOP

4O ACHIEVE A CHOPPED CONSISTENCY FOR VEGETABLES

cheese, meats, etc. ﬁll the bowl with the product no

more than ¾ full, or as low as two to three onions.

3MALLBATCHESWOULDREQUIRELOWERINGTHETOPCUTTING

BLADE7ITHTHELIDSECUREDANDTHESPEEDSELECTOR

IN,OWSPEEDPRESSTHEPULSEFUNCTIONQUICKLYTHEN

release. Repeat this pulsing action, allowing the blade

TOSTOPEACHTIMEUNTILTHEDESIREDCUTISACHIEVED

TO PUREE OR MIX

&ILLTHEBOWLWITHTHEPRODUCTNOMORETHANFULL

Start the machine in Low speed and allow to run until

THEPRODUCTISCOMPLETELYREDUCED)FNECESSARYTURN

THEMACHINEOFFANDSELECT(IGHSPEEDTOlNISHTHE

PRODUCT )T MAY BE NECESSARY TO ADD SOME LIQUIDS

TO APUREETOACHIEVETHEDESIREDCONSISTENCY )F A

COMPLETE HOMOGENEOUS MIXTURE IS REQUIRED FOR

ANALYTICALTESTINGITMAYBEREQUIREDTOSCRAPETHE

walls of the bowl one time during processing to

complete the homogeneous mixture.

DOUGHS AND PASTRIES

0REPARE DOUGHS AND PASTRIES ON ,OW SPEED ONLY

)N MANY CASES IT MAY BE HELPFUL TO lRST MIX ALL

DRYPRODUCTSTHENADDTHELIQUIDS4HE UNIT SHOULD

 .EXT SLOT THE 

stainless-steel blade assem-

BLYOVERTHEMOTORSHAFTAND

place the mini lid on top

OF THE MINI BOWL TO AVOID

SPLASHING .EXT CLOSE THE

machine lid.

s3%22!4%$",!$%&).%3%22!4%$",!$%

4HEBLADESUPPORTCANBElTTEDEITHERWITHTWOCOARSE

serrated blades or with two ﬁne serrated blades.

4HESERRATEDBLADESAREMAINLYUSED

FORMAKINGPASTRY

- for grinding.

4HElNESERRATEDBLADESAREMAINLYUSEDFOR

CHOPPINGPARSLEY

- blending

s6!#55-+)426!#

9OURCUTTERCANPERFORMVACUUMPROCESSINGWITHOUT

ANYNEEDFORMODIlCATIONS

3IMPLY ASSEMBLE THE VACUUM KIT 26!#

, patented

BY2/"/4#/50%ONTOTHELIDANDCONNECTITTOA

VACUUMPUMPSEEINSTRUCTIONSPAGE

)F YOU ALREADY HAVE A VACUUM PACKING MACHINE

YOUCANCONNECTTHEKITTOTHEVACUUMPUMPONTHIS

machine.

2OBOT#OUPEDOESNOTMARKETVACUUMPUMPS

4HE 26!#

 KIT WAS SPECIlCALLY DESIGNED SO THAT

LIQUIDSCANBEADDEDTOTHEMIXTUREDURINGPROCESSING

WHILEKEEPINGTHEFOODUNDERVACUUM

CLEANING

WARNING

As a precaution, always unplug your appliance

before cleaning it (hazard of electrocution) and

handle the blades with care (hazard of injury).

BERUNCONTINUOUSLYUNTILTHEPRODUCTISCOMPLETELY

PROCESSED&ORTHICKDOUGHSSUCHASFORPIZZATHE

machine will form a ball of dough when the mixing

IS COMPLETE 7HEN A BOWL IS FORMED THE MACHINE

SHOULD BE TURNED OFF IMMEDIATELY TO PREVENT OVER

processing. Preparation times and all ingredients

should be noted for different recipes.

As an example: detailed process for bread dough

4HEBLADEASSEMBLYMUSTBESETUPWITHTWOBLADES

ONLY

$ONOTUSETHELIDWIPERBOWLSCRAPER

- Mix all ingredients except water and salt for 15

seconds on low speed,

- Stop the unit, open the lid and add water and salt

(needs about 20 seconds),

- Knead for 35 seconds on low speed*. Stop

IMMEDIATELYTHEMACHINEWHENTHEBALLISFORMED

TOAVOIDANYOVERHEATINGOFTHEDOUGH

* Approximate duratÚn: to set according to your own recipe.

OPTIONS

s34!).,%3334%%,-).)"/7,

Optional extra: 3.5-litre mini bowl for the R 8 and

LITREMINIBOWLFORTHE2AND2PLUS

STAINLESSSTEELBLADEASSEMBLYEASILYTAKENAPARTFOR

MAKINGQUICKSAUCESCHOPPING HERBS ANDCARRYING

out all those other last-minute tasks or small batches.

s34!).,%3334%%,-).)"/7,7)4(,)42%

CAPACITY FOR R 8 AND 4-LITRE CAPACITY

&/22s2

0LACETHEMINIBOWLOVER

THE CHIMNEY OF THE LARGE

bowl, then turn it until it

lTS INTO POSITION OVER THE

LUG4HEMINIBOWLHANDLES

should now be lined up with

those of the large bowl.

7HENTHEMACHINEHASCOMPLETEDITSTASKOPENTHE

LIDBYRELEASINGTHELOCKINGHANDLE

0RESSDOWNlRMLYONTHE HANDLESUNLOCKTHEBOWL

BY TURNING IT IN A CLOCKWISE DIRECTION THEN PULL IT

upwards to free it.

)FTHEFOODHASASOLIDCONSISTENCYREMOVETHEBLADE

ASSEMBLY BY GRASPING BLADE KNOB TO REMOVE THE

BLADETHENEMPTYTHEBOWL

CAUTION CUT HAZZARD

!LWAYSUSESPATULAORSCRAPERTOREMOVEFOODFROM

THEBLADESNEVERUSEBAREHANDS

4OREMOVEFOODRESIDUEFROMTHEBLADESPUTTHEBOWL

BACKSLOTTHEBLADEASSEMBLYBACKOVERTHEMOTOR

SHAFTANDRUNTHEMACHINEATHIGHSPEED3IMILARLY

for precleaning, pour a couple of litres of hot water

into the bowl and run the machine for a few seconds

at high speed.

4HE MACHINE CAN BE WASHED WITH A KITCHEN SPRAY

(though not with a power washer).

IMPORTANT

Like the bowl and lid, the blade assembly should

also be removed for cleaning after use.

Always allow all metal parts, especially knives,

to dry completely on a plastic rack before assem-

bling components for storage to avoid corrosion.

IMPORTANT

Check that your detergent is suitable for cleaning

the plastic parts.

Certain washing agents are too alkaline (e.g.

high levels of caustic soda or ammonia) will

rapidly deteriorate plastic parts.

!FTERCLEANINGTHEBLADEASSEMBLYALWAYSCOMPLETELY

DRY THE BLADES TO PREVENT RUSTING OR AIRDRY METAL

parts on a plastic rack before assembling the blade

FOROVERNIGHTSTORAGE

7HENTHEMACHINEISNOTINUSETURNOFFATSERVICE

DISCONNECTORDISCONNECTFROMTHEPOWERSUPPLYAND

LEAVETHELIDOPEN

Never immerse the motor base in water. Clean

using a damp cloth or sponge.

MAINTENANCE

s$)3-!.4,).'4(%",!$%!33%-",9

2s2s2s2BLADE

ORLITREMINIBOWLBLADEASSEMBLY

!SPECIALTOOLISSUPPLIED

with the machine to

disassemble the mini bowl

BLADEASSEMBLY

s",!$%3

7E STRONGLY RECOMMEND THAT THE BLADES SMOOTH

ONES ARE SHARPENED DAILY USING THE SHARPENING

stone supplied with the machine.

4HE QUALITY OF THE CUT DEPENDS MAINLY ON THE

SHARPNESSOFYOUR BLADES ANDTHEDEGREEOF WEAR

4HEBLADESAREACTUALLYWEARINGPARTSWHICHSHOULD

BEREPLACEDOCCASIONALLYTOENSURECONSISTENTQUALITY

in the ﬁnal product.

s3%!,

4HE SEAL ON THE MOTORSHAFT SHOULD BE LUBRICATED

REGULARLYUSINGAFOODSAFELUBRICANT

)NORDERTOKEEPTHEMOTORCOMPLETELYWATERTIGHTITIS

ADVISABLETOCHECKTHEGASKETMONTHLYFORWEARAND

TEARANDREPLACEIFNECESSARY

Replace shaft seals each 3 to 6 months. Lubricate

seals with food grade grease.

s,)$3%!,

4HE LIDISDESIGNEDTOBECOMPLETELYWATERTIGHT )N

ORDERTOENSURETHATIT REMAINS THAT WAYYOU MAY

HAVETOCHANGETHESEALOCCASIONALLYDEPENDINGON

HOWREGULARLYYOUUSEYOURMACHINE

)FYOUDONOTUSEYOURMACHINEREGULARLYBETWEEN

USESITISADVISABLETOLEAVETHELIDOPENTOPRESERVE

the lid seal original caracteristics.

s3LIDETHEBLADEASSEMBLY

right down the motorshaft.

s-AKESURETHATTHELOWER

blade is resting on top of

the blade dismantling tool.

s,OOSENTHELOCKINGNUTWITH

the special wrench.

s4OREASSEMBLE THE BLADE ASSEMBY SIMPLY DO THE

SAMEINREVERSEORDER

s$ISCONNECTTHEMACHINE

power cord.

s2EMOVETHEBOWL

s0OSITIONTHEBLADE

dismantling tool on the

motor shaft.



4° USING THE VACUUM KIT R-VAC

#ONNECTUPTHEVACUUMPUMPTOVALVE!

CHECKTHATTHELATTERISOPENLEVERINSHAFTOF

connector).

3HUTVALVE"PERPENDICULARLEVER

ª!33%-",).'4(%6!#55-+)426!#

)NSERTlLTER.ªINTOBODYN° 3

- Screw part .ªONTOBODYN° 3THETUBEISFEDTHROUGHBODYN° 3).

ª0,!#).'4(%6!#55-+)426!#

ON THE LID

)NSERTTHEVACUUMKITINTOTHECONESECTIONOFTHEPLASTIC

part .ª  4HE LATTER SHOULD BE SCREWED INTO THE LID

guide N° 6 which, in turn, should be slotted into the

aluminium lid arm N° 84HELIDN° 9 should also be

clipped onto the lid guide N° 6.

ª!$$).',)15)$4/4(%-)8452%

!TTACHATUBETOVALVE"

)MMERSETHEOTHERENDOFTHISTUBEINTHELIQUIDTOBE

added.

/PENVALVE"SLOWLYONCETHELIQUIDHASBEENADDED

SHUTVALVE"

3° CLIPPING THE RETAINER N° 4

(OLDTHERETAINERINTHEPALMOFYOURHANDANDPRESS

the pusher N° 7INWITHYOURTHUMB

&IT THE NUT ONTO THE CYLINDRICALSECTIONWHICHJUTSOUT

OVERTHELID

- Release button N° 7.

4HE PUSHER SHOULD RETURN TO ITS EXTENDED LOCKED

POSITION)FITDOESNOTPRESSTHERETAINERGENTLYSOTHAT

ITAUTOMATICALLYCLICKSINTOPLACE

#HECKTHATTHERETAINERISPROPERLYATTACHEDTOTHETUBE

.ªINORDERTOAVOIDALLRISKOFTHEBELLORKITFALLING

off.

OPERATING INSTRUCTIONS FOR THE VACUUM KIT R-VAC

Keep an eye on the positÚn

of the O-ring seal when fitting

part .ª

FŠter .ª can

be cleaned.

Check that the openings are in

the upper positÚn in order to

positÚn nut N° 4.

NOTE

Follow operating instructions as provided by

the manufacturer of your vacuum pump





.OLIGHT

4HISMEANSTHATEITHERYOURAPPLIANCEISSWITCHEDOFF

ORTHEREISAPROBLEMWITHTHEPOWERSUPPLY

DIAGNOSTIC SYSTEM

9OURAPPLIANCEISEQUIPPEDWITHAGREENLIGHTTHAT

INDICATESTHEOPERATIONALSTATUSOFYOURMACHINE

- no light: see paragraph 1.

- ﬂashing light: see paragraph 2.

- steady lightYOURAPPLIANCEISREADYTORUN

-EASURETHEVOLTAGEATTHEPOWEROUTLETANDCHECK

THATTHEPLUGISCORRECTLYWIRED

)F THE PROBLEM PERSISTS THE CONTROL BOARD MUST BE

replaced.

&LASHINGLIGHT

/NE OR MORE OF THE SAFETY DEVICES OR THERMAL

PROTECTORSISNOTRESPONDINGPROPERLY

4HESESAFETYDEVICESCOMPRISEPRESENCESENSORSA

THERMALRELAYANDAMOTOROVERLOADPROTECTOR

4HESTATUSLIGHTANDTHECONTROLBUTTONSOFFERAMEANS

OF TESTING THE MACHINES COMPONENTS AND SAFETY

DEVICESBEFOREPERFORMINGANYSERVICEOPERATION

4HEREISNOPOINTCONTINUINGWITHTHETESTONCEYOU

HAVE DETECTED A FAULT )NSTEAD RECTIFY THE PROBLEM

ﬁrst and start the test afresh.

s'ENERALPOINTS

4HE PREVIOUS TABLE HELPS YOU FOLLOWING THE TEST

procedure.

)TIDENTIlESTHEDEVICETHATCANBETESTEDASFOLLOW

Each of the 4 columns corresponds to one of the 4

BUTTONSPRESSEDONEAFTERTHEOTHERBYTHEOPERATOR

4HE  ROWS CORRESPOND TO THE  SUCCESSIVE TEST

LEVELS

9OUCANCHANGETHELEVELBYSIMULTANEOUSLYPRESSING

buttons I and II%ACHLEVELISIDENTIlEDBYTHEmASHING

SPEEDOF THELIGHTSLOWFORLEVELONEFASTFORLEVEL

TWOANDVERYFASTFORLEVELTHREE4ORETURNTOTESTING

LEVELTHEbuttons I and IIMUSTBESIMULTANEOUSLY

pressed a further time.

7HENNONEOFTHEBUTTONSISBEINGPRESSEDTHELIGHT

mASHESTOINDICATETHECURRENTTESTINGLEVEL

7HEN ONE OF THE BUTTONS IS CONTINUOUSLY PRESSED

it indicates the actual status of the corresponding

DEVICEON/+OFFPROBLEM

s4ESTSEQUENCE

7HEN THE GREEN LIGHT mASHES START BY PRESSING

button ITOTESTTHATITISWORKINGPROPERLYSIMILARLY

test button II and then test button T).

!TTHISLEVELbutton OCANNOTBETESTEDYET

Press buttons I and II SIMULTANEOUSLY TO MOVE UP

TOTESTINGLEVELINDICATEDBYMORERAPIDmASHING

speed of the indicator light.

!T LEVELbuttons I, II, T and O allow to test the

presence sensors of the lid, the base and the bowl,

and button ORESPECTIVELY

Press buttons I and II SIMULTANEOUSLYTOMOVEUPTO

TESTINGLEVELINDICATEDBYVERYRAPIDmASHINGSPEED

of the indicator light.

!T LEVELbuttons I, II, T and O allow to test the

THERMAL RELAY  THE MOTOR THERMAL PROTECTOR THE

MAINSVOLTAGETHEPHASEFREQUENCYDETECTORANDTHE

CONlGURATIONJUMPERSBRAKINGRELAYRESPECTIVELY

Press buttons I and II SIMULTANEOUSLY TO RETURN TO

THE NORMAL mASHING SPEED ANDTHEREFORETO TESTING

LEVEL

s#HECKS

)FTHETESTSEQUENCEREVEALSABUTTONDEFAULTCHECK

ﬁrst the button’s contact block operation and its

wiring.

- )FTHETESTSEQUENCEREVEALSAPROBLEMWITHONEOFTHE

PRESENCESENSORSCHECKTHAT THE REMOVABLEPARTS

OFYOURCUTTERMIXERBOWLLIDANDARMAREALLIN

PLACE)F THEPROBLEMPERSISTSCHECKTHEPRESENCE

SENSORSTHEMSELVESANDTHEIRWIRING

REMEMBER

The control system requires the lid be opened and

closed, once after switching your appliance on.

This sequence will check the correct operation of

the lid arm safety switch. At this stage, if all the

conditions are met for operation, the light will

stop ﬂashing and stay on.

REMEMBER

Always switch your machine off before carrying

out any cleaning or maintenance.

All repair and maintenance work must be

carried out by a qualiﬁed technician.

)FTHETESTSEQUENCEINDICATESTHATTHETHERMALRELAY

ISFAULTYCHECKITISCORRECTLYSETAUTOMATICPOSITION

and current setting in accordance with the electrical

DIAGRAM

)FTHETESTINDICATESTHATTHEMOTOROVERLOADPROTECTOR

ISFAULTYCHECKITSWIRING

)FAiVOLTAGEwORi0HASE&REQUwERRORISDETECTED

check that the machine is supplied with the correct

VOLTAGE !LSO CHECK THAT THE PLUG ATTACHMENT IS

CORRECTLYWIRED

)F A i*UMPERS  +&2wERRORMESSAGEISDETECTED

CHECKTHATTHECONlGURATIONJUMPERSONTHECONTROL

board are set according to the electrical diagram.

Plastic

ring

Blade Long ring

Screw

nut

Narrow

spacer

Blade

support

s",!$%!33%-",9

7ERECOMMENDYOUUSE THE TWOBLADE ASSEMBLY FORPROCESSINGSMALL

AMOUNTSLESSTHANHALFTHEMAXIMUMCAPACITYINDICATEDONPAGE

0OSITION

2EGULARBLADEASSEMBLY

0OSITION

2EGULARBLADEASSEMBLY

0OSITION

#OARSEMINCINGASSEMBLY

0OSITION

#OARSEMINCINGASSEMBLY

0/3)4)/.7ITHSPACERBETWEENLOWERBLADEANDBLADESUPPORT

  s&ORcoarse chopping

ASSEMBLING: s&ITTHEBLADESANDSPACERSSOTHATTHEYARETHERIGHTDISTANCEAPARTACCOR-

ding to the:

TYPE

- weight and

VOLUMEOFTHEFOODSTUFFSTOBEPROCESSED

WARNING: The plastic ring must be placed immediately under the locking nut.

#ORRECTPOSITIONING

OFBLADEASSEMBLY

TOPVIEW

#ORRECTPOSITIONING

OFBLADEASSEMBLY

TOPVIEW

0/3)4)/. .OSPACERBETWEENLOWERBLADEANDBLADESUPPORT

s&ORﬁne chopping and emulsions.

s&ORgrinding and kneading.

DISMANTLING: s5NSCREWTHESCREWNUT

s2EMOVETHERINGSANDBLADES

s",!$%!33%-",9

7E RECOMMEND YOU USE THE BLADE ASSEMBLY FOR PROCESSING LARGE QUANTITIES OF MORE THAN HALF THE

MAXIMUMLIMITINDICATED WITHTHEEXCEPTION OF LIQUIDOR BLENDED PREPARATIONSFOR WHICH WESTRONGLY

RECOMMENDYOUUSETHEBLADEASSEMBLYFor preparations of this kind, it is recommended using the

low speed in order to obtain the best results.

FITTING AND USING THE BLADE ASSEMBLY

Plastic spacer

TECHNICAL

SPECIFICATIONS

s7%)'(4$)-%.3)/.3

s%,%#42)#!,$!4!

s7/2+).'30!#%

0LACE THE MACHINE IN A CLEAR mOOR SPACE SUFlCIENTLY

large for the operator to use and clean the machine

SAFELY

s./)3%,%6%,

4HEEQUIVALENTCONTINUOUSSOUNDLEVELWHENTHEMACHINE

ISOPERATINGONNOLOADISLESSTHAND"!

Models Motor

Low

speed

(rpm)

High

speed

(rpm)

Output

power

(Watts)

Rated

current

(Amp.)

R 8 220V / 60 Hz - 3 1800 3600 1500 9.9

R 10 220V / 60 Hz - 3 1800 3600 1800 11.8

R 15 220V / 60 Hz - 3 1800 3600 2100 17.8

R 20 220V / 60 Hz - 3 1800 3600 3300 21.3

Models

DimensÚns (in inche) Weight (Lb)

A B C D E F G H Net Gross

R 8

23 17 ½ 10 11

R 10

26 20 ½ 11 11

39 126

R 15

26 ¾ 21 ¼ 11

24 ¼ 42 ½ 137

R 20

30 24 12 ¾ 12 ¾ 14

65 194

Vacuum kit

R-vac

2.20

Vacuum pump

61.7

SAFETY

This ROBOT-COUPE range of cutter mixers is

equipped with a electro-mechanical safety system

and a motor brake. Moreover, the machine will

not operate unless the bowl and lid are correctly

positioned on the motor base.

4HE MOTOR STOPS AS SOON AS THE LID IS OPENED

(OWEVER WHEN PROCESSING LIQUID INGREDIENTS THE

user must stop the machine before opening the lid, to

AVOIDSPLASHING

4HIS IS VERY IMPORTANT ESPECIALLY WITH HOT

ingredients.

4ORESTARTTHEMACHINESIMPLYCLOSETHELIDANDPRESS

the low or high speed button.

4HESEMODELSARElTTED

- with a thermal relay that stops the machine when

it is overloaded. 4HE THERMAL RELAY RESETS ITSELF

AUTOMATICALLYAFTERAFEWTENSOFSECONDS

SERVICE

3EEWARRANTYlRSTTHEN

3HOULD YOUR UNIT REQUIRE SERVICE CHECK ONLINE AT

www.robotcoupeusa.com to ﬁnd the nearest Robot

#OUPE!UTHORIZED3ERVICE!GENCYORCALLTHEFACTORY

TOSEEWHERELOCALSERVICEISAVAILABLE

)FYOUWISHYOURUNIT TOBESERVICEDATTHEFACTORY

call for return instructions and ship the unit prepaid

TOOURFACTORYADDRESS

0(

2OBOT#OUPE53!)NC

3ERVICE$EPARTMENT2EPAIR

264 South Perkins Street

Ridgeland, MS 39157

&ORSERVICEIN#ANADACONTACTTHE2OBOT#OUPE

53!FACTORYFORREPAIRINSTRUCTIONS

WARNING

The blades are extremely sharp. Handle with

care.

Wear cut resistant gloves when handling the

blades.

REMEMBER

Never try to override the locking and safety

systems.

Never insert an object into the container where

the food is being processed.

Never push the ingredients down with your

hand.

Do not overload the appliance.

Never switch the appliance on when it is

empty.

- a thermal protector insterted in the motor winding

that stops the machine if the motor temperature rises

ABOVETHEMAXIMUMLIMIT)THISHAPPENSALLOWTHE

MACHINETOCOOL DOWNFORSEVERAL MINUTESABOUT

10 to 20 minutes) before attempting to restart it.

TECHNICAL DATA

Page is loading ...

Robot Coupe R 15 Operating Instructions Manual

Brand: Robot Coupe

Model: R 15

Category: Small kitchen appliances

Type: Operating Instructions Manual

This manual is also suitable for

Download PDF

report

Robot Coupe R 15 Operating Instructions Manual

This manual is also suitable for

Robot Coupe R 15 Operating Instructions Manual

Related papers

Other documents