Extron RCP 2000 User manual

Extron
Brand
Extron
Model
RCP 2000
Category
Network switches
Type
User manual

This manual is also suitable for

User's Guide
68-575-02 Rev. A
Printed in the USA
10 03
The RCP 2000 will work with an ISS 108 or ISS 408 that has firmware version 1.01 or later.
Check the firmware installed in your ISS switcher. If the installed firmware is version is 1.0 or
earlier, install the firmware chips that are attached to this sheet.
Check the ISS’s Firmware level
Apply power to the ISS. During the power up process, the switcher displays the model name,
part number, and the firmware version in its LCD display (figure 1).
2
sec.
2
sec.
2
sec.
2
sec.
Extron Electronics
ISS 408
Integration
Seamless Switcher
Extron Electronics
ISS 408
60-423-01
Version
x
.
xx
Version 1.00 or earlier,
you must replace the
firmware.
Version 1.01 or later,
you do not need to
replace the firmware.
Program #1 RGB
0.00 kHz 0.00Hz
Preview #3 S-Video
0.00 kHz 0.00Hz
Output Rate
1280 x 1024 @ 60
Power
on
Default Display Cycle
Figure 1 — Identifying the firmware version
Replace the ISS’s Firmware
1. Disconnect the AC power cord from the ISS to remove power from the unit.
To prevent electric shock, always unplug the ISS from the AC power source before
opening the enclosure.
CAUTION
Changes to firmware must be performed by authorized service personnel only.
2. If the ISS is installed in a rack, disconnect all signal and control cables and remove the ISS
from the rack.
3. Remove the 16 screws, 8 on the top and 4 on each side of the ISS cover (figure 2 on the
opposite side of this guide).
4. Remove the top two front panel screws.
5. Lift the top cover straight up approximately five inches until you can access the fan power
cords.
CAUTION
Do not touch any switches or other electronic components inside the ISS. Doing so
could damage the switcher. Electrostatic discharge (ESD) can damage IC chips even
though you cannot feel it. You must be electrically grounded before proceeding with
firmware replacement. A grounding wrist strap is recommended.
6. Disconnect the two fan power cords from connectors J8 and J13 on the main board.
7. Lift the top cover out of the way.
8. Locate firmware chip U6 on the front panel circuit board and chips U98, U99, U100, and
U101 on the main circuit board (figure 2).
9. After you are electrically grounded, use a DIP chip puller to grasp the IC
chips and pull them out of the socket.
10. The table in figure 2 identifies the socket into which each firmware chip
is to be installed.
Ensure the correct chip is installed in each socket. The wrong chip will
not work and may damage the ISS.
The U98 and U100 chips are identical and can be installed in either
location.
The U99 and U101 chips are identical and can be installed in either location.
1
2 3 4
5
6
7
8
100
-
240
5
0
/6
0
H
z
1.2A MAX.
R
1
G
B
H
/H
V
R
2
G
B
H
/H
V
R
3
G
B
H
/H
V
R
IN
P
U
T
S
4
G
B
H
/H
V
R
5
G
B
H
/H
V
R
6
G
B
H
/H
V
R
7
G
B
H
/H
V
R
8
G
B
H
/H
V
B
H
/H
V
V
H
/H
V
V
Remove (16)
screws.
Remove top two
front panel screws.
Lift cover straight up.
Extron
ISS 408
Switcher
J8
J13
Connect to
J8 and J13
U100
U101
U6
U98
U99
Chip part #
19-1222-01
19-1218-02
19-1218-01
Location
U6
U98 or U100
U99 or U101
Figure 2 — Opening the switcher and firmware locations
11. Align the notches on one end of each chip with the notches in the socket in the same
orientation as the old chips. Gently, but firmly, press the chips into place in the socket.
12. Reconnect the two fan power cords to connectors J8 and J13 on the main board. It does not
matter which fan is connected to which connector.
13. Replace the top cover on the ISS.
14. Fasten it with the screws that were removed in step 3 and step 4.
15. Rack mount the switcher if desired and reconnect all cables.
The new firmware has several new features and revised LCD displays. Obtain the latest
ISS 108 and ISS 408 manual from the Extron Web site, www.extron.com.
Align
Notches
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Extron Electronics, Japan
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
www.extron.com
© 2003 Extron Electronics. All rights reserved.
  • Page 1 1
  • Page 2 2

Extron RCP 2000 User manual

Extron
Brand
Extron
Model
RCP 2000
Category
Network switches
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents