2. Computers & electronics
  3. Computer components
  4. Chassis components
  5. Computer cases
  6. Sharkoon
  7. Rebel9 Aluminum U3

Sharkoon Rebel9 Aluminum U3 Specification

  • Hello! I am an AI chatbot trained to assist you with the Sharkoon Rebel9 Aluminum U3 Specification. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
REBEL9 ALU U3
Handbuch
Manual
Manuel d‘utilisation
Guia usario
Manuale d´istruzioni
Gebruiksaanwijzing
Guia usário
Instukcja obstugi
使用手冊
2
REBEL9 ALU U3
Content
1. Features 3
2. Package content 3
3. The case at a glance 5
4. Installation of a mainboard 7
5. Installation of a PSU 9
6. Installation of a HDD 10
7. Installation of an optical device 11
8. Installation of a 3.5" device 13
9. Installation of an add-on card 14
10. The pre-installed fan 15
11. Installation of additional fans / optimized airflow 15
Dear customer!
Congratulations for purchasing this premium quality SHARKOON product.
For a long life time and to take full advantage of this product we recommend that you read
this manual completely.
Have a good time with our product!
SHARKOON Technologies
3
REBEL9 ALU U3
1. Features
• MidiATXcase
• 9x5.25"drivebays
• TopI/Owith1xUSB3.0,2xUSB2.0,1xheadphoneand1xmicrophoneconnector,
powerandresetbutton
• 7slotsforadd-oncards
• Aluminumfrontpanel
• Quickfastenersforopticaldrives,mainboardmountingpanelwithinstallation
opening for coolers
• 2openingsforwatercooling
• Cablemanagementsystem
• Fanconguration:
Case front
1x 120 mm fan with 3-pin and 4-pin connector
(pre-installed)
Side panel 2x120mmfan(optional)
Backside 1x80mmor1x120mmfan(optional)
Toppanel 1x120mmor1x140mmfan(optional)
• Dimensions:455x202x440mm(LxWxH)
• Weight:~6kg
2. Package content
• PCcase“Rebel9Aluminum”
• Screwkit:
Screwsformainboard
mounting
ScrewsforPSU
mounting
Screws for drive
mounting(3.5"and5.25")
Screws for HDD mounting
4
REBEL9 ALU U3
• Accessorykit:
Stand-offsformainboard Washers Lockattachment(A)andspeaker(B)
MountinganglesforHDDs(decoupled/A)and
3.5"devices(notdecoupled/B)
Quickfastenersforopticaldrives 5.25"bezelwith3.5"opening
Note:
If you are missing any of the items listed above, please contact our customer service
immediately:
suppor[email protected] (Germany and Europe)
suppor[email protected] (international).
A
B
A B
5
REBEL9 ALU U3
3. The case at a glance
Front view
A– LEDsforpowerandHDDactivity
B– 5.25"drivebays
C– covered:pre-installed120mmfan
Viewfromabove
A– Fanbracket
B– TopI/Owith:
a– Powerand
b– Resetbutton,
c –1xheadphoneand
1xmicrophoneconnector
d– 2xUSB2.0and
e– 1xUSB3.0connector
Sideview(closed/left)
A– Bracketsfortwo120mmfans
a
b
c
A
A
A
B
B
C
d
e
6
REBEL9 ALU U3
Sideview(opened/left)
A– Drivebaysfor5.25"devices
B– Mainboardmountingpanelwith:
a– Installation opening for CPU
coolers and
b– Cablemanagementsystem
Backsideview
A– OpeningforI/Oshield
B– Fanbracket
C– Slotbezels
D – Openings for water cooling
E– PSUbracket
F– Thumbscrews
Bottomview
A – Case feet
B– AirintakeforPSU
Note:
For more information on how to install the intended devices, refer to their respective
documents.
a
b
A
A
B
B
C
D
E
F
F
F
F
A A
AA
B
7
REBEL9 ALU U3
4. Installation of a mainboard
1.Openthecasebylooseningthethumbscrewsonthecase’sbacksideandremovingtheleft
sidepanel.Laydownthecasesidewiseonanevensurface.
2.The mainboard’s mounting panel inside the case provides various drillings to x the
stand-offs(g.1).
g.1
Themainboardcontainsspecialscrewopenings(g.2).
g.2
Place the mainboard to the mounting panel. A stand-off must be screwed into every
drillingofthemountingpanelvisiblethroughthemainboard’sscrewopenings.
8
REBEL9 ALU U3
3.Remove the mainboard and screw the stand-offs into the respective drillings of the
mountingpanel(g.3).
(Stand-offs)
g.3
4.PresstheI/Oshield(deliveredwiththemainboard)intotheI/Oshieldopeninginthecase’s
backside.
5.Placethemainboardbackontothestand-offsandscrewthemainboardtothem(g.4).
(Screwsformainboardmounting)
g.4
9
REBEL9 ALU U3
6.Plugtheconnectorsofthecase’sfrontbezeltotherespectiveconnectorsofthemainboard
(alsorefertoyourmainboard’smanualforfurtherinformation).
5. Installation of a PSU
1.SetupthecaseinfrontofyouandputthePSUfromtheinsideagainstthePSUbracketon
thecase’sbackside(g.5).
g.5
2.ScrewthePSUtothecasefromtheoutside(g.6).
(ScrewsforPSUmounting)
 g.6
10
REBEL9 ALU U3
6. Installation of a HDD
1.Removethecase’srightsidepanel.
2.AttachthedecoupledmountinganglestotheHDDfrombothsides(g.7).
(ScrewsforHDDmounting)
(Decoupledmountingangles)
g.7
3.Slide the HDD with attached mounting angles into the case’s respective drive bay and
screwitfrombothsides(g.8).
g.8
4.ConnecttheHDDtothepowersupplyandthemainboard.
11
REBEL9 ALU U3
7. Installation of an optical device
1.Removethecase’sfrontpanelbygentlydraggingittowardsyou(g.9).
g.9
2.Dismantlethe5.25"frontbezelfromthemountingbayinwhichyouintendtoinstallthe
drivebylooseningitsscrewsandpushingthebezeltotheinside(g.10).Removethequick
fasteners(g.11).
g.10g.11
(Carefullytakeoutanoptionallypresentmetalbezelcoveringthe3.5"drivebaybyusinga
gripper.)
3.Slidetheopticaldriveintothecase’sdrivebay(g.12).
 g.12
12
REBEL9 ALU U3
4.Attachtheopticaldevicefrombothsidesusingthequickfasteners(g.13).
 g.13
Note:
If you intend to transport the case we recommend securing (additionally) the installed
drives:
(Screwsfor5.25"drivemounting)
5.Connecttheopticaldrivetothepowersupplyandthemainboard.(Putthefrontbezelback
ontothecase.)
8. Installation of a 3.5" device
(1.Removethecase’sfrontpanelbygentlydraggingittowardsyou.)
2.Dismantlethe5.25"frontbezelfromthemountingbayinwhichyouintendtoinstallthe
drivebylooseningitsscrewsandpushingthebezeltotheinside(g.14).Removethequick
fasteners(g.15).
g.14g.15
13
REBEL9 ALU U3
(Carefully take out an optionally present metal bezel covering the drive bay by using a
gripper.)
3.Screwthemountinganglestothe3.5"devicefrombothsides(g.16).
g.16
4.Slidethe3.5"devicewithattachedmountingrailsintothecase’sdrivebay(g.17)and
screwittothedrivebayfrombothsides(g.18).
g.17g.18
5.Connectthe3.5"devicetothepowersupplyandthemainboard.
6.Screwthe5.25"bezelwith3.5"openingintothefrontpanel(g.19)andplaceitbackonto
the case.
(5.25"bezelwith3.5"opening)
g.19
14
REBEL9 ALU U3
9. Installation of an add-on card
1.Removetheslotbezel’sxationscrewandtakeawaytheslotbezel(g.20).
g.20
2.Insert the add-on card into the mainboard’s respective slot and x it to the case by
re-attachingthexationscrew(g.21).
g.21
10. The pre-installed fan
1.Thepre-installed120mmfrontfanprovidesa4-pinPSUconnectoranda3-pinmainboard
plug.
2.ConnectoneofbothplugstoeithertherespectivePSUor(tocontrolthefanspeedviathe
mainboard)thematchingmainboardconnector.
15
REBEL9 ALU U3
11. Installation of additional fans / optimized airflow
1.Placethefanagainsttherespectivebracketfromtheinside(e.g.inthetoppanel/g.22).
g.22
2.Screwthefantotheattachmentfromtheoutside(g.23).
g.23
Note:
The Rebel 9 Aluminum case offers a lot of possibilities to install fans.
While installing fans make sure that (cool) air is taken in on the case’s front side/bottom and
blown out on its back side/top. The PC components with the highest heat development
should be placed directly within the airflow.
16
REBEL9 ALU U3
Legal disclaimer:
AsacontinuingpolicyofproductimprovementatSHARKOON,thedesignandspecications
aresubjecttochangewithoutpriornotice.Nationalproductspecicationsmayvary.
All rights reserved especially (also in extracts) for translation, reprinting, reproduction by
copyingorothertechnicalmeans.Infringementswillleadtocompensation.
All rights reserved especially in case of assignation of patent or utility patent. Means of
deliveryandtechnicalmodicationsreserved.
Disposal of your old product
Your product is designed and manufactured with high quality materials and components,
whichcanberecycledandreused.
Whenthiscrossed-outwheeledbinsymbolisattachedtoaproduct,itmeanstheproductis
coveredbytheEuropeanDirective2002/96/EC.
Pleasebeinformedaboutthelocalseparatecollectionsystemforelectricalandelectronic
products.
Pleaseactaccordingtoyourlocalrulesanddonotdisposeofyouroldproductswithyour
normalhouseholdwaste.Thecorrectdisposalofyouroldproductwillhelppreventpotential
negative consequences to the environment and human health.
© SHARKOON Technologies 2012
www.sharkoon.com
/