Garmin GPSMAP® 420/420s User manual

Brand: Garmin

Model: GPSMAP® 420/420s

Type: User manual

Installing the Flush Mount Kit

Use this kit to ush mount a Fishnder 400C or GPSMAP 400 series unit into a at panel.

Select an appropriately sized location for the unit.

Use the Flush Mount Template provided to determine a location.

Check that all cables reach the unit mounting location.

Always wear safety goggles and a dust mask when drilling, cutting, or sanding.

Included mounting hardware—(1) unit housing, (2) tension mount brackets, (4) hex bolts, (4) hex nuts, (4) wing nuts,

and (4) Phillips head screws.

Tools (not included)—drill, 3/8" (10 mm) drill bit, jig saw, 9/32" (7 mm) wrench, and Phillips screwdriver.

To install the Quick Release Flush Mount Kit:

1. Cut the opening:

The ush mount template has adhesive on the back. Remove the protective liner and apply the template to the location you want to

mount the unit.

Using a 3/8" (10 mm) drill bit, drill the pilot holes indicated on the template to begin cutting the mounting surface.

Using the jig saw, cut the mounting surface along the inside of the line indicated on the template. Be very careful when cutting this

hole, because there is only a small amount of clearance between the unit housing and the tension mount arms. Cut slightly inside the

indicated line and then sand or le the panel as needed to obtain the best t.

2. Assemble the ush mount hardware (see Figure 1):

Insert the (4) hex bolts into the unit housing so they stick out of the back.

Use the (4) hex nuts to secure the hex bolts to the unit housing. Using the 9/32” (7 mm) wrench, tighten the nuts without

overtightening.

Slide the unit into the unit housing.

Using the (4) Phillips head screws, attach the unit housing to the unit.

Connect the wiring harness to the unit (This can be done after step 3, if preferred).

Unit

Hex bolts

Hex nuts

Phillips head screws

Hex nuts

Hex bolts

Figure 1

•

October 2007 Part Number 190-00757-02 Rev. D Printed in Taiwan

3. Install the unit in the opening (see Figure 2):

Place the unit housing in the recently cut hole in the mounting surface.

Slide the tension mount arms onto the hex bolts and secure them with the (4) wing nuts.

Tighten the (4) wing nuts to secure the unit housing to the mounting surface. Be careful not to overtighten.

Assembled unit and

ush mount hardware

Tension mount brackets

Wing nuts

Figure 2

NOTE: If you are installing a Fishnder 400C, the wiring harness must be connected to the boat’s power supply and transducer per the installation

instructions included with the unit.

NOTE: If you are installing a GPSMAP 400 series unit, you must connect the wiring harness to the boat’s power supply, GPS antenna, XM antenna

(if applicable), and transducer (if applicable) per the installation instructions included with the unit.

•

Page is loading ...

Garmin GPSMAP® 420/420s User manual

Brand: Garmin

Model: GPSMAP® 420/420s

Type: User manual

Download PDF

report

in other languages

italiano: Garmin GPSMAP® 420/420s Manuale utente
français: Garmin GPSMAP® 420/420s Manuel utilisateur
español: Garmin GPSMAP® 420/420s Manual de usuario
Deutsch: Garmin GPSMAP® 420/420s Benutzerhandbuch
русский: Garmin GPSMAP® 420/420s Руководство пользователя
Nederlands: Garmin GPSMAP® 420/420s Handleiding
português: Garmin GPSMAP® 420/420s Manual do usuário
dansk: Garmin GPSMAP® 420/420s Brugermanual
svenska: Garmin GPSMAP® 420/420s Användarmanual
suomi: Garmin GPSMAP® 420/420s Ohjekirja

Garmin GPSMAP® 420/420s User manual

Garmin GPSMAP® 420/420s User manual

in other languages

Related papers

Other documents