Ricoh Aficio 1600Le Owner's manual

DDST Unit Type A / Type B

Operating Instructions

Printer / Scanner Reference

Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the

Safety Information in the "Copy Reference" before using the machine.

Getting Started

Installing the Software

Using the Printer Function

Using the TWAIN Scanner Function

Troubleshooting

Appendix

1

2

3

4

5

6

Introduction

This manual contains detailed instructions and notes on the operation and use of this machine. For your

safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy

place for quick reference.

Important

Contents of this manual are subject to change without prior notice. In no event will the company be li-

able for direct, indirect, special, incidental, or consequential damages as a result of handling or oper-

ating the machine.

Do not copy or print any item for which reproduction is prohibited by law.

Copying or printing the following items is generally prohibited by local law:

bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, passports, driver's licens-

es.

The preceding list is meant as a guide only and is not inclusive. We assume no responsibility for its

completeness or accuracy. If you have any questions concerning the legality of copying or printing cer-

tain items, consult with your legal advisor.

Caution:

Use of controls or adjustments or performance of procedures other than those specified in this manual

might result in hazardous radiation exposure.

Two kinds of size notation are employed in this manual. With this machine refer to the metric version.

Trademarks

Microsoft

®

, Windows

®

and Windows NT

®

are registered trademarks of Microsoft Corporation in the

United States and/or other countries.

Other product names used herein are for identification purposes only and might be trademarks of their

respective companies. We disclaim any and all rights to those marks.

The proper names of the Windows operating systems are as follows:

• The product name of Windows

®

98 is Microsoft

®

Windows

®

98

• The product name of Windows

®

Me is Microsoft

®

Windows

®

Millennium Edition (Windows Me)

• The product name of Windows

®

2000 are as follows:

Microsoft

®

Windows

®

2000 Advanced Server

Microsoft

®

Windows

®

2000 Server

Microsoft

®

Windows

®

2000 Professional

• The product name of Windows

®

XP are as follows:

Microsoft

®

Windows

®

XP Professional

Microsoft

®

Windows

®

XP Home Edition

• The product names of Windows Server

TM

2003 are as follows:

Microsoft

®

Windows Server

TM

2003 Standard Edition

Microsoft

®

Windows Server

TM

2003 Enterprise Edition

Microsoft

®

Windows Server

TM

2003 Web Edition

Notes:

Some illustrations in this manual might be slightly different from the machine.

Certain options might not be available in some countries. For details, please contact your local dealer.

i

Manuals for This Machine

The following manuals describe the operational procedures of this machine. For

particular functions, see the relevant parts of the manual.

Note

❒ Manuals provided are specific to machine type.

❒ Adobe Acrobat Reader is necessary to view the manuals as a PDF file.

❖ General Settings Guide

Provides an overview of the machine and describes System Settings (paper

trays, Key Operator Tools, etc.), and troubleshooting.

❖ Network Guide

Describes procedures for configuring the machine and computers in a net-

work environment.

❖ Copy Reference

Describes operations, functions, and troubleshooting for the machine’s copier

function.

❖ Printer/Scanner Reference (this manual)

Describes system settings, operations, functions, and troubleshooting for the

machine’s printer/scanner function.

ii

TABLE OF CONTENTS

Manuals for This Machine ......................................................................................i

How to Read This Manual .....................................................................................1

1. Getting Started

Control Panel..........................................................................................................3

Reading the Display and Using Keys.........................................................................4

Connecting the Machine .......................................................................................5

Requirements.............................................................................................................5

Connecting the machine to the host using a USB cable ............................................5

2. Installing the Software

Auto Run.................................................................................................................7

Installing the Printer Driver...................................................................................8

Installing the TWAIN Driver...................................................................................9

Software Supplied on CD-ROM ..........................................................................10

DDST Driver.............................................................................................................10

DDST TWAIN Driver ................................................................................................10

3. Using the Printer Function

Printer Features Menu .........................................................................................11

Adjusting Printer Features..................................................................................12

Printer Features Parameters...............................................................................13

Paper Input...............................................................................................................13

List/Test Print ...........................................................................................................13

Maintenance.............................................................................................................14

System .....................................................................................................................15

Host Interface...........................................................................................................16

Setting Paper on the Bypass Tray......................................................................17

Setting the paper size ..............................................................................................18

Setting custom size paper........................................................................................19

Setting thick paper or OHP transparencies..............................................................20

Setting envelopes.....................................................................................................21

Setting Up the Printer Driver and Canceling a Print Job .................................22

Windows 98SE / Me - Accessing Printer Properties ................................................22

Windows 2000 / XP and Windows Server 2003 - Accessing Printer Properties ......22

Canceling a Print Job ...............................................................................................24

4. Using the TWAIN Scanner Function

TWAIN Scanner ....................................................................................................27

Preparation for Using the Network TWAIN Scanner.........................................28

TWAIN Scanner Screen...........................................................................................28

Setting Originals ..................................................................................................29

Placing Originals ......................................................................................................29

Scanning Originals ..............................................................................................32

iii

5. Troubleshooting

The Printer Function............................................................................................33

Error & Status Messages on the Display .................................................................33

The Machine Does Not Print ....................................................................................36

Other Printing Problems...........................................................................................38

The Scanner Function .........................................................................................40

When Scanning Is Not Performed as Expected .......................................................40

When an Error Message Appears on the Client Computer......................................40

6. Appendix

The Printer Function............................................................................................43

Collate and Rotating Collate ....................................................................................43

Edge to Edge Printing ..............................................................................................43

The Scanner Function .........................................................................................44

Relationship between Resolution and File Size .......................................................44

Specifications.......................................................................................................45

Printer.......................................................................................................................45

Scanner....................................................................................................................46

INDEX......................................................................................................... 47

iv

1

How to Read This Manual

Symbols

In this manual, the following symbols are used:

R

WARNING:

This symbol indicates a potentially hazardous situation which, if instructions

are not followed, could result in death or serious injury.

R

CAUTION:

This symbol indicates a potentially hazardous situation which, if instructions

are not followed, may result in minor or moderate injury, or damage to proper-

ty.

* The statements above are notes for your safety.

Important

If this instruction is not followed, paper might misfeed, originals might be dam-

aged, or data might be lost. Be sure to read this.

Preparation

This symbol indicates prior knowledge or preparation is required before opera-

tion.

Note

This symbol indicates precautions for operation, or actions to take after mal-op-

eration.

Limitation

This symbol indicates numerical limits, functions that cannot be used together,

or conditions in which a particular function cannot be used.

Reference

This symbol indicates a reference.

[]

Keys and buttons that appear on the computer's display.

[]

Keys that appear on the machine's display.

{}

Keys built into the machine's control panel.

{}

Keys on the computer's keyboard.

2

3

1. Getting Started

Control Panel

1. {Scanner} key

Press to activate the scanner function.

2. {Printer} key

Press to activate the printer function.

3. Indicators

Displays errors and machine status.

h: Error indicator. See Network Guide

and General Settings Guide.

B: Load Paper indicator. See Copy Refer-

ence.

D: Add Toner indicator. See Copy Refer-

ence.

4. Display

Displays operation status and messages.

5. Selection keys

Correspond to items on the display. Press

to select the corresponding item.

6. Scroll keys

Press to select an item.

{U}: scroll upward

{T}: scroll downward

{V}: scroll right

{W}: scroll left

7. {User Tools/Counter} key

Press to change default or operation pa-

rameters according to requirement.

8. {Clear/Stop} key

Clear: clears an entered numeric value.

9. Main power indicator and On in-

dicator

The main power indicator lights when

the main power switch is turned on. The

On indicator lights when the operation

switch is turned on.

10. Operation switch

Press to turn the power on. The On indi-

cator lights. To turn the power off, press

again.

Note

❒ This key is inactivate during printing

or while setting printer defaults.

11. {Online} key

Press to switch the printer between on-

line and offline.

12. Data In indicator

Blinks while the printer is receiving data

from a computer or printing. Lit when

preparing to print.

13. {Escape} key

Press to cancel an operation or return to

the previous display.

14. {OK} key

Press to set a selected item or entered nu-

meric value.

15. Number keys

Press to enter numeric values.

11

15

12 13 14

ANX003S

1 2

4

3

6

5

7 98 10

Getting Started

4

1

Reading the Display and Using Keys

This section explains how to read the display and using the selection key for the

initial display.

Note

❒ The copy display is set as the default screen when the machine is turned on.

You can change the settings in [System Settings]. See General Settings Guide.

1. Selection keys

Correspond to the function items at the

bottom line on the display.

Example: Basic screen

When the instruction "press [JobReset]"

appears in this manual, press the center

selection key.

2. {Escape} key

Press to cancel an operation or return to

the previous display.

3. {OK} key

Press to set a selected item or entered nu-

meric value.

4. Scroll keys

Press to move the cursor in each direc-

tion, step by step.

When the {U}, {T}, {V}, or {W} key ap-

pears in this manual, press the scroll key

of the same direction.

ANX004S

123

4

Connecting the Machine

5

1

Connecting the Machine

Reference

For details about connection using

Ethernet, see "Connecting the Net-

work Cable to the Network", Net-

work Guide.

Requirements

Before using this machine, make sure

all environmental and electrical re-

quirements are met. Connect the ma-

chine to the host computer using the

USB port or network interface unit.

Make sure all cables, connectors, and

electrical outlets necessary to attach

the machine to the host computer or

network are close at hand.

Connecting the machine to the

host using a USB cable

You can connect the machine to the

host computer using a USB interface

cable.

The USB cable is provided according

to machine model:

• Standard model

The USB cable is provided for this

model.

• Network standard model

The USB cable is not provided for

this model. Purchase a cable that is

suitable for connecting this model

to your computer.

Follow the procedure below to con-

nect the machine to the host computer

using a USB interface cable.

A Connect the USB 2.0 interface ca-

ble to the USB port on the right

side of the machine's back cover.

B Connect the other end to the USB

port on the host computer.

The machine and computer are

now connected. The printer driver

and TWAIN driver must be in-

stalled next. For details about how

to install the printer driver and

TWAIN driver, see p.8 “Installing

the Printer Driver” and p.9 “In-

stalling the TWAIN Driver”.

Note

❒ If USB 2.0 is used with Win-

dows 98 SE/Me, only a speed

equivalent that of USB 1.1 is

possible.

ANX001S

Getting Started

6

1

7

2. Installing the Software

This manual assumes you are familiar with general Windows procedures and

practices. If you are not, see the operating instructions that come with Windows

for details.

Auto Run

Inserting the CD-ROM into the CD-

ROM drive starts the installer auto-

matically. The installer helps you in-

stall the following printer drivers and

software easily.

Note

❒ When “plug and play” starts, click

[Cancel] in [New Hardware Found],

[Device Driver Wizard] or [Found New

Hardware Wizard] dialog box, and

then insert the CD-ROM. The [New

Hardware Found], [Device Driver Wiz-

ard] or [Found New Hardware Wizard]

dialog box appears depending on

the system version of the Windows

98SE / Me / 200 / XP, or Windows

Server 2003.

❒ Auto Run may not work with cer-

tain operating system settings. If

this happens, launch "Setup.exe"

on the CD-ROM root directory.

❒ To disable Auto Run, press the left

{SHIFT} key when inserting the

CD-ROM into the drive and keep it

pressed until the computer finish-

es reading from the CD-ROM.

Limitation

❒ Under Windows 2000 / XP, or

Windows Server 2003, installing

software using Auto Run requires

Administrator permission. When

you install software using Auto

Run, log on using an account that

has Administrators permission.

Installing the Software

8

2

Installing the Printer Driver

When you are using the printer func-

tion, you must install the printer driv-

er on the supplied CD-ROM.

A Quit all applications currently run-

ning.

B Insert the CD-ROM into the CD-

ROM drive.

The driver installer starts.

C Select an interface language, and

then click [OK].

The default interface language is

English.

D Click [DDST Printer Drivers].

The DDST Printer Drivers installer

starts.

E The software license agreement

appears in the [License Agreement]

dialog box. After reading through

its contents, click [I accept the agree-

ment.], and then click [Next >].

F Follow the instructions on the

display to install DDST Printer

Drivers.

If you are required to restart the

computer after installing DDST

Printer Drivers, restart the compu-

ter.

Note

❒ The printer driver has been in-

stalled, plug and play is ena-

bled, and the icon of the printer

connected to the “USB” port is

added to the [Printers] or [Print-

ers and Faxes] window.

❒ When you use the printer func-

tion on the Ethernet interface

under Windows 98SE / Me, see

"Using the Printer Function",

Network Guide.

❒ When you use the printer func-

tion on the Ethernet interface

under Windows 2000 / XP /

Server 2003, see "Using the

Printer Function", Network

Guide.

Installing the TWAIN Driver

9

2

Installing the TWAIN Driver

When you are using the scanner func-

tion, you must install the TWAIN

driver on the supplied CD-ROM.

A Quit all applications currently run-

ning.

B Insert the CD-ROM into the CD-

ROM drive.

The driver installer starts.

C Select an interface language, and

then click [OK].

The default interface language is

English.

D Click [DDST TWAIN Driver].

The DDST TWAIN Driver installer

starts.

E Click [Close].

Installing the Software

10

2

Software Supplied on CD-ROM

There are some CD-ROMs that come with the printer option of this machine.

DDST Driver

The DDST drivers are included on the CD-ROM that comes with this machine.

This allows the computer to communicate with the machine via a printer lan-

guage.

❖ System requirements

Operating system

• Microsoft Windows 98SE

• Microsoft Windows Me

• Windows 2000

•Windows XP

• Windows Server 2003

Hard disk space

• 80 MB or more

DDST TWAIN Driver

This driver is required to scan an original on the machine.

To use the machine as a network TWAIN scanner, this driver must be installed.

❖ System requirements

•Hardware

PC/AT compatible

•CPU

Pentium 300 MHz or faster recommended

• Operating system

Microsoft Windows 98 (SE or later)

Microsoft Windows Millennium Edition

Microsoft Windows 2000 Professional

Microsoft Windows 2000 Server

Microsoft Windows XP Home Edition

Microsoft Windows XP Professional

•Memory

128 MB or more recommended

• Hard disk space

200 MB or more

•Connection

Ethernet/USB

11

3. Using the Printer Function

Printer Features Menu

There are five menu items in the Printer Features menu:

Reference

For more information about copier features and system settings, see Copy Ref-

erence and General Settings Guide.

•Paper Input

• List/Test Print

•Maintenance

•System

•Host Interface

You can select the following functions.

*1

Appears on the duplex standard model. Check your machine type.

Menu

Default

Paper Input

See p.13 “Paper Input”.

Bypass Paper Size

Auto Paper Select

Duplex

*1

List/Test Print

See p.13 “List/Test

Print”.

Operations Test

Maintenance

See p.14 “Maintenance”.

Menu Protect

System

See p.15 “System”.

Auto Continue

Edge Smoothing

Toner Saving

Host Interface

See p.16 “Host Interface”.

I/O Timeout

Using the Printer Function

12

3

Adjusting Printer Features

Printer Features allows basic adjustment of operations when using the machine

as a printer.

Although factory default settings are suitable for most print jobs, Printer Fea-

tures allows you access to a number of settings that control basic printer opera-

tions. Printer Features settings you make are retained even when you turn off

the machine.

For details about copier features and system settings, see Copy Reference and Gen-

eral Settings Guide.

A Press the {User Tools/Counter} key.

B Select [Printer Features] using the {U} or {T} key, and then press the {OK}

key.

C Select the desired item using the {U} or {T} key, press the {OK} key, and

then change its settings.

Note

❒ {OK}: Press to make new settings and go back to previous menus.

❒ {Escape}: Press to return to a previous menu without changing any set-

ting.

D After changing the Printer Features settings, press the {User Tools/Counter}

key.

Note

❒ Changes made to functions remain in effect even if the machine is turned

off.

Printer Features Parameters

13

3

Printer Features Parameters

Paper Input

❖ Bypass Paper Size

The size of the paper set in the by-

pass tray.

Reference

For more information about pa-

per sizes that can be set in the

bypass tray, see General Settings

Guide.

Note

❒ Default:

•Metric version: A4

• Inch version: 11 × 8/

❖ Auto Paper Select

You can set this to enable Auto Pa-

per Select. This machine automati-

cally detects the paper size from

the print data, and selects the pa-

per feed tray.

Note

❒ Default: On

❖ Duplex

You can set this to enable the du-

plex printing. This machine detects

the duplex printing from the print

data, and selects the paper feed

tray.

Note

❒ Default: On

List/Test Print

❖ Operations Test

You can print the operations test

page.

Printing the operations test page

A Press the {User Tools/Counter} key.

The User Tools main menu ap-

pears.

B Select [Printer Features] using the

{U} or {T} key, and then press

the {OK} key.

The Printer Features menu ap-

pears.

C Select [List/Test Print] using the

{U} or {T} key, and then press

the {OK} key.

D Select [Operations Test] using the

{U} or {T} key, and then press

the {OK} key.

The operations test page is printed.

E Press the {User Tools/Counter} key.

Using the Printer Function

14

3

Maintenance

❖ Menu Protect

This procedure allows you to pro-

tect menu settings from accidental

change. It makes it impossible to

change menu settings with normal

procedures unless you perform the

required key operations.

• Level 1

You can protect “Maintenance”,

”System”, “Host Interface”.

• Level 2

You can protect ”Paper Input”,

“Maintenance”, ”System”,

“Host Interface”.

•Off

Note

❒ Default: Off

Setting Menu Protect

A Press the {User Tools/Counter} key.

The User Tools main menu ap-

pears.

B Select [Printer Features] using the

{U} or {T} key, and then press

the {OK} key.

The Printer Features menu ap-

pears.

C Select [Maintenance] using the {U}

or {T} key, and then press the

{OK} key.

D Press [Menu Protect].

E Enter an access code using the

number keys, and then press the

{OK} key.

F Select a menu protect level, and

then press the {OK} key.

G Press the {User Tools/Counter} key.

Page is loading ...

Ricoh Aficio 1600Le Owner's manual

Ricoh Aficio 1600Le Owner's manual

Related papers

Other documents