George Kovacs P1230-286-L User manual

Brand: George Kovacs

Model: P1230-286-L

Type: User manual

George Kovacs P1230-286-L is a wall sconce fixture that provides both style and functionality to your living space. This dimmable fixture is compatible with C-L (CFL & LED) and Incandescent/Halogen type dimmers, allowing you to adjust the brightness to suit your needs. Installation is straightforward and can be completed by a qualified electrician, ensuring proper wiring and functionality. The fixture features a sleek and modern design, making it a perfect addition to any contemporary home décor.

INSTALLATION INSTRUCTIONS

For

READ AND SAVE THESE INST

W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R

A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O

ASSEMBLING THE FIXTURE (Fig.1)

Shut off power at the fuse box or circuit breaker. If necessary,

remove the old fixture including the mounting hardware.

Carefully remove the fixture from the carton and check that all parts

are included as show in Figure 1.

Attach mounting plate (A)

to the junction box with junction box

screws (C) (size:8-32*1/2”L) provided.

The side

plate marked “GND” must face out.

CONNECTION THE WIRES (Fig. 2)

Connect the electrical wires as shown in Fig.2, making sure that all

wire nuts are secured. If your outlet has a ground wire (green or

bare copper), connect the fixture's ground Wire to it. Otherwise,

connect the fixture's ground wire directly to the mount

the green screw (B) provided.

Tuck the wire connections neatly into

the junction box.

FINISHING THE INSTALLATION (Fig. 1)

Align fixture (E) onto mounting plate (A)

and secure

and rubber washers (F).

To prevent moisture from

entering the outlet box and causing a short

circuit

, use clear caulking (i.e. Indoor/Outdoor silicone sealant) to

outline the outside of fixture back plate where it meets the wall

leaving a space at bottom to allow moisture a means to escape

(Fig.3).

Your

installation is now complete. Return power to the junction box and

test the fixture.

CAUTION /ATTENTION:

When handling the fixture, do not apply

pressure to the LEDs. Hold the fixture by the base or back plate (E) only.

Replacing LED module (Fig. 4)

The LED module can be replaced by a qualified electrician without cutting

of wire and without damage to any decorative element to which the fixture

is attached. See installation steps for more details (Fig.

Warning: Turn off power at the circuit break

replacing LED module.

a. To remove the fixture from the wall, l

oosen screw

rubber washers (F). Disconnect t

he wire connectors and

fixture on a clear flat surface. (Fig. 1)

b. Loosen screws (M)

from inside the fixture back

frame(Q) and spacers (*W) (if applicable).L

oosen screw

remove the LED protective case (H).

c. Remove the waterproof silicon on the prote

ctive

screws

(J), remove cap (I), and take out glass panel

d. Loosen screws (L), rubber washers (S),

screw (R)

(G). Carefully remove LED module (K).

e. Reverse steps a-d

for installing the new LED module

Note: The LED module should be provided by a specified sup

IMPORTANT:

Fixture should be installed

by a qualified electrician

to ensure proper wiring and installation.

Dimmable with C-

L (CFL & LED) type and Incandescent/Halogen

type dimmers.

Fig.1

INSTALLATION INSTRUCTIONS

FOR P1230

For

Wall Sconce Fixture

READ AND SAVE THESE INST

RUCTIONS

WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R

A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O

Shut off power at the fuse box or circuit breaker. If necessary,

remove the old fixture including the mounting hardware.

Carefully remove the fixture from the carton and check that all parts

to the junction box with junction box

The side

of the mounting

Connect the electrical wires as shown in Fig.2, making sure that all

wire nuts are secured. If your outlet has a ground wire (green or

bare copper), connect the fixture's ground Wire to it. Otherwise,

connect the fixture's ground wire directly to the mount

ing plate using

Tuck the wire connections neatly into

and secure

with screws (D)

entering the outlet box and causing a short

, use clear caulking (i.e. Indoor/Outdoor silicone sealant) to

outline the outside of fixture back plate where it meets the wall

leaving a space at bottom to allow moisture a means to escape

installation is now complete. Return power to the junction box and

When handling the fixture, do not apply

pressure to the LEDs. Hold the fixture by the base or back plate (E) only.

The LED module can be replaced by a qualified electrician without cutting

of wire and without damage to any decorative element to which the fixture

is attached. See installation steps for more details (Fig.

Warning: Turn off power at the circuit break

er before

oosen screw

s (D) and remove

he wire connectors and

place the

from inside the fixture back

plate.Remove glass

oosen screw

s (P) and

ctive

case (H), loosen

(J), remove cap (I), and take out glass panel

(N).

screw (R)

and wire fastener

for installing the new LED module

Note: The LED module should be provided by a specified sup

plier.

Fig.2

by a qualified electrician

L (CFL & LED) type and Incandescent/Halogen

Fig.3

II 807

Fig.4

WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R

A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O

D I S J O N C T E U

George Kovacs P1230-286-L User manual

Brand: George Kovacs

Model: P1230-286-L

Type: User manual

Download PDF

report

George Kovacs P1230-286-L User manual

George Kovacs P1230-286-L User manual

Related papers

Other documents