The Water Well FS-Z03 User manual

Brand: The Water Well

Model: FS-Z03

Category: Ice cube makers

Type: User manual

The Water Well FS-Z03 is a 12-15kg Bullet Shape Block Ice Maker that can produce ice within 8-12 minutes. It has an easy-to-use touch button display, and you can choose between 3 ice cube sizes: large, medium, and small. The Water Well FS-Z03 also has a microcomputer control system, which allows it to produce ice faster and easier. Additionally, it has an ice full indicator light so you know when the ice basket is full, and a fill water indicator light so you know when to add more water.

USERS MANUAL

MODEL: FS-Z03

12- 15kg Bullet Shape Block Ice Maker

PLEASE READ USER MANUAL CAREFULLY

BEFORE USE, STORE IN A SAFE PLACE

The Water Well (Pty) Ltd

Address: P.O. Box 1854, Pinetown, 3600

Sharecall No.: 0860 099355

e-mail: [email protected] website: www.waterwell.co.za

Warranty Term: 12 Months

NOTE: This product's warranty is applicable only if the product has a valid

proof of purchase document

The Water Well

’

Table of Contents

Important Safety Instructions 1/2

Characteristics 2

Parts Diagram 3

How to Operate Your Ice Maker 4

Maintaining Your Ice Maker 5

Trouble Shooting 6/7

Specifications 7

Important Safety Instructions

When using electrical appliances, basic safety precautions should be

followed to prevent the risk of fire, electric shock, and injury to persons

or property. Read all instructions before using any appliance.

- DO NOT operate this or any other appliance that has a damaged

cord. Connect to properly polarised outlets only. No other appliance

should be plugged into the same outlet. Ensure that the plug is fully

inserted into the receptacle

- DO NOT run cord over carpeting or other heat insulators. DO NOT

cover the cord. Keep cord away from high traffic areas, and do not

submerge in water. DO NOT pull on the power cable

- We DO NOT recommend the use of an extension cord, as it may

overheat and become a fire hazard.

- Ensure the ice maker is positioned in such away that the power plug is

always accessable.

- Keep the ice maker away from direct heat and out of direct sunshine.

- Ambient surrounding temperatures should be within 15˚C - 25˚C for

optimum working conditions. Ice production may vary due to temperature

variances.

- Clean you ice maker regularly, approx. every 1-3 months.

- DO NOT clean the ice maker with water if the unit is still plugged into

the wall socket, instead wipe clean with a damp cloth.

- DO NOT clean your ice maker with flammable fluids. The fumes can

create a fire hazard or explosion.

- Exercise caution and use reasonable supervision when appliance is

used near children.

- DO NOT tilt the ice maker beyond 45˚ always keep upright.

- DO NOT touch the evaporator rods during operation.

- Ensure the ice maker is on a flat surface and placed at least 15cm from

the wall, and surrounding objects, for proper ventilation.

- WARNING - Keep the ice maker well ventilated if placed in an enclosed

area

- Unplug the ice maker from the wall socket and drain all the water from

the ice maker if the icemaker is not in use for a long time.

- Clean your ice maker before use, if it has not been used for a long

period, discard the water from water reservoir and clean the ice maker

thoroughly before refilling with water and starting the ice making cycle.

CAUTION: Plastic bags can be dangerous. To avoid danger of

suffocation, keep this bag away from babies and

children.

NOTE: DO NOT use water of an unknown quality in this ice maker.

Always use water from a confirmed drinkable source.

Characteristics

1. The Water Well Ice makers are energy efficient and emit very little

noise.

2. All the components of the Ice Maker are made of high grade materials

and the design is firm and durable quality

3. The Ice Maker will recycle any water that is in the water reservoir, ice

is stored in the ice basket, if this is not used it will melt back into the

water reservoir to start the ice making process again.

4. The Ice Maker has an easy to use touch button display, and you are

able to choose between 3 ice cube sizes, large, medium and small,

5. The Ice Maker can produce ice within 8-12 minutes if the water

temperature is in a temperature range of under 7°C, once the first

batch of ice is produced the water temperature is in the optimum range.

6. The Evaporator Rods can produce 12 bullet ice blocks at a time,

water fills the Ice Bucket and ice is formed around each of the

Evaporator Rods, once the ice has reached the correct size the Ice

Bucket tips over and drains the excess water and the Evaproator Rods

release the ice blockets onto the Ice Shovel, which scoops them into

the Ice Storage Basket. NOTE: please check regularily that no ice

blocks have gotten behind the Ice Bucket as this can cause damage

over time to the Ice Bucket and Ice Motor

7. The Ice Maker comes with a microcomputer control system, which

allows this unit to produce ice faster and easier.

Parts Diagram

1. Ice Storage Basket 2. Ice Scoop

3. Water Reservoir 4. Ice Shovel

5. Water Inlet Pipe 6. Evaporator Rods

7. Ice Bucket 8. Compressor

9. Water Pump 10. Drain Cap and Plug

11. Medium Ice Indicator Light 12. Small Ice indicator Light

13. Ice Full Indicator Light 14. “Start” Button

15. Clear Viewing Window 16. Lid

17. Large Ice Indicator Light 18. Fill Water Indicator Light

19. “Stop” Button 20. Ice Size Selection Button

Select

START

STOP

Fill WaterIce Full

4 5

How to Operate Your Ice Maker

1. Remove the Ice Maker from the packaging, and remove all sticky

tape from the interior of the Ice Maker

2. Clean the inside and outside of the Ice Maker thoroughly.

3. Remove the Ice Storage Basket and Scoop.

4. Fill the Water Reservior with water until the maximum water level

mark. (DO NOT overfill the Water Reservoir)

5. Insert the plug into an electrical socket and turn on the power.

6. Push the “START” button on the touch pad situated on the top of the

Ice Maker.

7. Press the “SELECT button to choose between Small (the Indicator

light above the ”S” with turn on), Medium (the Indicator Light above

the “M” will turn on) or Small (the Indicator Light above the “S” will

turn on) Ice Cubes.

8. Water will begin to be pumped from the Water Reservoir and start

to fill the Ice Bucket and surround the Evaporator Rods.

9. The Ice Maker produces 12 bullet shaped ice cubes at a time. Once

the ice blocks are produced, they will release from the Evaporator

Rods and be shoveled by the Ice Shovel into the Ice Basket

10. The first cycle of ice production maybe a little slow. Please discard

this first batch of ice to ensure that there are no impurities in the ice.

Ensure the Water Reservoir is full and allow the ice production to

continue.

11. Once the Ice Storage Basket is full (ice has filled the Ice Storage

Basket and is touching the Ice Sensor) the “ICE FULL” indicator light

will turn on and the ice production will stop. When the ice level has

dropped, ice production will start again.

NOTE: Please ensure that you do not use heavy chemical detergents

when cleaning the Water Reservoir or interior of the Ice Maker,

as it may get inside the Ice Maker and may cause the ice

produced to have a peculiar taste. If you do get detergent

inside the Ice Maker’s water pump, ensure you flush the

system thoroughly to remove all traces from the Ice Maker.

NOTE: If you require large quantities of ice, remove ice from the Ice

Storage Basket and store in the freezer, as the ice will melt back

into the reservoir if left inside the Ice Maker

12. If the Water Reservoir is empty the ice production will stop and the

“FILL WATER” indicator light will turn on.

13. Please refill the Water Reservoir and press the start button again.

14. If yourequire your Ice Maker to stop, press the “STOP” button.

NOTE: The Ice maker will work at its optimum level if cold water within

a temperature range of 7 - 35 °C is used. The warmer the water

used and the warmer the surrounding ambient temperature, the

the longer the ice cycle will be.

Maintaining Your Ice Maker

1. Always ensure that you clean your Ice Maker on a regular basis.

2. Unplug your Ice Maker before cleaning.

3. Move the Ice Maker to an area where you are able to drain any excess

water.

4. Remove the drain cap and plug from the rear of the Ice Maker and

allow the water to drain from the system.

5. Remove the Ice Basket and Scoop and using a damp cloth and diluted

mild soap detergent. Wipe clean the water reservoir and interior of the

Ice Maker.

6. Using a clean damp cloth wipe all soapy residue from the interior of

your ice maker.

7. Leave the lid open and allow to air dry.

8. Clean the Ice Basket and Ice Scoop in soapy water and rinse

thoroughly

9. Wipe down the outside of the Ice Maker with a damp cloth and

detergent. Rinse off all soapy residue with a damp cloth.

10. Dry the exterior with a dry cloth.

NOTE: If the unit is not in use for long periods of time please ensure

that all the water is drained from the system as per step 4

above. Always ensure that you clean your Ice Maker if the

Ice Maker has not been in use.

6 7

Troubleshooting

PROBLEM

POSSIBLE CAUSE

SOLUTION

1. The Compressor

makes a buzzing

sound when turned

The Voltage is lower than

required to run the ice maker

Stop the ice maker, only

restart when the voltage is

correct

2. “Fill Water”

Indicator light is

permanently lit

The Water Pump is not

working

The Water Pump is only

working for 10 seconds then

it stops

Contact your closest repair

centre

Adjust the Water Sensor to

the Water Inlet Tube

3. “Ice Full” indicator

light is on, but

there are only a

few ice cubes in

the storage basket

The Internal temperature

of the ice maker is too low

Open the lid of the ice maker

and allow to stand open for a

short period of time, until the

indicator light goes off

4. There are no lit

indicator lights on

the control panel

The plug is not connecting

properly with the wall socket

The Fuse is blown

Check the Wall socket to

ensure it is functioning properly

Contact your closest repair

centre

5. Both the “Fill

Water” and “Ice

Full” indicator

lights are

permanently on

There are ice cubes in the

evaporator panel, but the

panel is unable to release

them

There are too many ice

cubes in the storage basket

The ice cubes are too large

and are fusing together

There is a fault on the

control panel

The water sensor is to high

to detect the water level.

Remove the ice cubes and allow

the ice maker to rest for a short

period and then restart

Remove ice cubes from the

storage basket

Stop the ice maker, pour hot

water over the fused ice blocks

to melt them back into the

reservoir. allow the ice maker

to rest with thelid open and then

restart

Contact your closest repair

centre

Adjust the water sensor to the

water inlet tube

PROBLEM

POSSIBLE CAUSE

SOLUTION

6. The water is not

freezing during

the normal ice

making cycle

There is a refrigerant leak

The electromagnet valve is

incorrect

Contact you closet repair

centre

Contact your closet repair

centre

Specifications

Ice Making Capacity 12 - 15kg / 24hr

Ice Storage Capacity 800g (when Ice basket is full)

Water Reservoir Capacity 1.8lt

Climate Type N

Electrical Protection Type I

Rated Voltage AC220 - 240V

Rated Frequency 50Hz

Power Rating 160W

UNit Dimensions (WDH) 435 x 355 x 375 mm

N.W. 12.2kg

The Water Well FS-Z03 User manual

Brand: The Water Well

Model: FS-Z03

Category: Ice cube makers

Type: User manual

Download PDF

report

The Water Well FS-Z03 User manual

The Water Well FS-Z03 User manual

Other documents