Barco BarcoReality 6400 DLC User manual

Brand: Barco

Model: BarcoReality 6400 DLC

Category: Data projectors

Type: User manual

This manual is also suitable for

BARCO PROJECTION SYSTEMS

OWNER'S MANUAL

REALITY

6400i

R9002800

R9002809

Art. No. :

R5976277

Rev. :

Date :

20042001

Due to constant research, the information in this manual is subject to change without notice.

Produced by BARCO NV, Januari 2001.

Trademarks are the rights of their respective owners.

BARCO n.v./Projection Systems

Noordlaan 5

B-8520 Kuurne

Belgium

Tel : +32/56/368211

Fax : +32/56/351651

E-mail : [email protected]

Visite Barco at the web : http://www.barco.com

Printed in Belgium

Federal communication commission (FCC statement)

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Instructions to the user :

if this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the

following measures :

- Re-orientation of the receiving antenna for the radio or television.

- Relocate the equipment with respect to the receiver.

- Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.

 Fasten cables connectors to the equipment by mounting screws.

Note :

The use of shielded cables is required to comply within the limits of Part15 of FCC rules and EN55022.

1-1

Table of Contents

5976277 BARCOREALITY 6400i 20042001

TABLE OF CONTENTS ...................................................................................................... 1-1

PACKAGING AND DIMENSIONS ...................................................................................... 2-1

Projector Packaging ..................................................................................................................................... 2-1

Way of Packaging............................................................................................................................................................................. 2-1

To unpack ......................................................................................................................................................................................... 2-1

Hint.................................................................................................................................................................................................... 2-1

Contents of the complete unit (box) : ............................................................................................................................................... 2-1

Lens Packaging ............................................................................................................................................ 2-1

Way of Packaging............................................................................................................................................................................. 2-1

Projector Case .............................................................................................................................................. 2-2

Dimensions ....................................................................................................................................................................................... 2-2

INSTALLATION GUIDELINES............................................................................................ 3-1

Safety warning .............................................................................................................................................. 3-1

Installation Guidelines .................................................................................................................................. 3-1

Ambient Temperature Conditions ..................................................................................................................................................... 3-1

Environment...................................................................................................................................................................................... 3-1

Environment condition check ........................................................................................................................................................... 3-1

What about ambient light ?............................................................................................................................................................... 3-1

Which screen type? .......................................................................................................................................................................... 3-2

What image size? How big should the image be?.......................................................................................................................... 3-2

Projector Configurations ............................................................................................................................... 3-2

Which configuration can be used ? .................................................................................................................................................. 3-2

Positioning the Projector................................................................................................................................................................... 3-2

Lenses .......................................................................................................................................................... 3-3

Which lens has to be selected. ........................................................................................................................................................ 3-3

Available lenses................................................................................................................................................................................ 3-3

Lens formulas to calculate the projector distance. .......................................................................................................................... 3-4

How to install the lens? .................................................................................................................................................................... 3-4

Cleaning the Lens............................................................................................................................................................................. 3-5

Battery installation in the RCU. .................................................................................................................... 3-5

Inserting the Batteries. ..................................................................................................................................................................... 3-5

How to replace the batteries in the RCU ? ...................................................................................................................................... 3-6

Note .................................................................................................................................................................................................. 3-6

CONNECTIONS .................................................................................................................. 4-1

Power connection to Projector ..................................................................................................................... 4-1

AC Power (mains) cord connection.................................................................................................................................................. 4-1

Fuses ................................................................................................................................................................................................ 4-1

Switching on ..................................................................................................................................................................................... 4-1

Lamp Run Time ................................................................................................................................................................................ 4-2

Lamp Run Time Warning.................................................................................................................................................................. 4-2

Switching to Stand-by. ...................................................................................................................................................................... 4-2

Switching Off..................................................................................................................................................................................... 4-3

Switching to Stand-by Warning ........................................................................................................................................................ 4-3

Input Source Connection .............................................................................................................................. 4-3

Input facilities ..........................................................................................................................................................................................

4-3

Input Selection .................................................................................................................................................................................. 4-3

Input Facilities, RCVDS05 connected.............................................................................................................................................. 4-3

5-cable Input Slot (slot 1) ................................................................................................................................................................. 4-4

Computer input/Monitor output......................................................................................................................................................... 4-5

Video Input........................................................................................................................................................................................ 4-6

S-Video Input .................................................................................................................................................................................... 4-6

Serial Digital Input / Serial Digital Output (optional)......................................................................................................................... 4-7

1TABLE OF CONTENTS

1-2

Table of Contents

5976277 BARCOREALITY 6400i 20042001

IEEE 1394 Input................................................................................................................................................................................ 4-8

RS232 Connection........................................................................................................................................ 4-9

RS232 in / RS232 out....................................................................................................................................................................... 4-9

Applications : .................................................................................................................................................................................... 4-9

Set up of the Baud Rate for Communication with a Computer : .................................................................................................... 4-9

Communication port for communication with peripherals ............................................................................ 4-9

Configurations of the port. ................................................................................................................................................................ 4-9

Connecting a RCVDS 05 to the projector. ....................................................................................................................................... 4-9

MOUSE....................................................................................................................................................... 4-10

When available ? ............................................................................................................................................................................ 4-10

How to activate ? ............................................................................................................................................................................ 4-10

Available Mouse Functions ............................................................................................................................................................ 4-10

Netwerk Connection (optional) ................................................................................................................... 4-10

What can be done ? ....................................................................................................................................................................... 4-10

Audio Connections.......................................................................................................................................4-11

What is available ? ..........................................................................................................................................................................4-11

How to lock an audio input ? ...........................................................................................................................................................4-11

GETTING STARTED ........................................................................................................... 5-1

Remote Control & Local Keypad .................................................................................................................. 5-1

How controlling the projector ?......................................................................................................................................................... 5-1

Location of the local keypad............................................................................................................................................................. 5-1

Remote control ................................................................................................................................................................................. 5-1

...................................................................................................................................................................... 5-1

Overview of Terminology .................................................................................................................................................................. 5-1

Operating the Projector ................................................................................................................................ 5-2

Switching on ..................................................................................................................................................................................... 5-2

Lamp Run Time ................................................................................................................................................................................ 5-3

Lamp Run Time Warning.................................................................................................................................................................. 5-3

Switching to Stand-by. ...................................................................................................................................................................... 5-3

Switching Off..................................................................................................................................................................................... 5-3

Switching to Stand-by Warning ........................................................................................................................................................ 5-3

Quick Set Up Adjustments............................................................................................................................ 5-3

Quick Lens Adjustment..................................................................................................................................................................... 5-3

...................................................................................................................................................................... 5-4

Quick On Screen Color change........................................................................................................................................................ 5-4

Using the RCU.............................................................................................................................................. 5-5

Pointing to the reflective screen ....................................................................................................................................................... 5-5

Hardwired Remote Input. ................................................................................................................................................................. 5-5

Directly to one of the IR sensors of the projector. ........................................................................................................................... 5-5

Projector address.......................................................................................................................................... 5-6

Why a projector address ? ............................................................................................................................................................... 5-6

Set up an Individual Projector Address. ........................................................................................................................................... 5-6

How to control the projector or projectors. ....................................................................................................................................... 5-6

Before using the RCU. ..................................................................................................................................................................... 5-6

Common Address ............................................................................................................................................................................. 5-6

...................................................................................................................................................................... 5-6

Displaying the Projector Address on the Screen. ............................................................................................................................ 5-6

How to Program an Address into the RCU? .................................................................................................................................... 5-6

...................................................................................................................................................................... 5-6

Sound Controls ................................................................................................................................................................................. 5-7

Controlling the Projector ............................................................................................................................... 5-7

Input Selection .................................................................................................................................................................................. 5-7

Picture controls. ................................................................................................................................................................................ 5-7

The Pause key.................................................................................................................................................................................. 5-8

The Selection key. ............................................................................................................................................................................ 5-8

START UP OF THE ADJUSTMENT MODE ....................................................................... 6-1

Adjustment Mode.......................................................................................................................................... 6-1

Start Up............................................................................................................................................................................................. 6-1

Possible Paths .................................................................................................................................................................................. 6-1

Password Protection......................................................................................................................................................................... 6-1

Entering the Password ..................................................................................................................................................................... 6-1

Remark ............................................................................................................................................................................................. 6-2

Setting up your own password ......................................................................................................................................................... 6-2

1-3

Table of Contents

5976277 BARCOREALITY 6400i 20042001

AUTO IMAGE ADJUSTMENT ............................................................................................ 7-1

Auto Image Adjustment ................................................................................................................................ 7-1

Why Auto Image ? ............................................................................................................................................................................ 7-1

Adjust............................................................................................................................................................ 7-1

What can be done ? ......................................................................................................................................................................... 7-1

Image Adjustment............................................................................................................................................................................. 7-1

Action............................................................................................................................................................ 7-2

What can be done ? ......................................................................................................................................................................... 7-2

Setup................................................................................................................................................................................................. 7-2

RANDOM ACCESS ADJUSTMENT MODE ....................................................................... 8-1

Random Access Mode .................................................................................................................................. 8-1

Overview Flowchart .......................................................................................................................................................................... 8-1

Possible File Manipulations. ............................................................................................................................................................. 8-2

File Annotation. ................................................................................................................................................................................. 8-2

Starting Up ........................................................................................................................................................................................ 8-2

Picture Service ............................................................................................................................................. 8-2

Connecting a new Source. ............................................................................................................................................................... 8-2

Start up the File Service. .................................................................................................................................................................. 8-2

Load File ....................................................................................................................................................... 8-3

How to load a file ? ........................................................................................................................................................................... 8-3

The image is not perfect ?................................................................................................................................................................ 8-3

Edit File......................................................................................................................................................... 8-3

What can be done with the Edit File menu ? ................................................................................................................................... 8-3

How to start up the Edit menu ?....................................................................................................................................................... 8-4

Which items can be adjusted ? ........................................................................................................................................................ 8-4

How to change the settings ?........................................................................................................................................................... 8-4

How to find the correct values for the displayed item?.................................................................................................................... 8-4

Rename a file................................................................................................................................................ 8-6

How to change the characters ? ...................................................................................................................................................... 8-7

Copy a file..................................................................................................................................................... 8-7

How to change the characters ? ...................................................................................................................................................... 8-7

Delete ........................................................................................................................................................... 8-8

File Options................................................................................................................................................... 8-8

File Sort............................................................................................................................................................................................. 8-8

Picture Tuning............................................................................................................................................... 8-9

Which items are available ? ............................................................................................................................................................. 8-9

CTI ON/OFF ................................................................................................................................................. 8-9

What is CTI ?.................................................................................................................................................................................... 8-9

How to change thet CTI settings...................................................................................................................................................... 8-9

Note : ................................................................................................................................................................................................ 8-9

Color Temperature ...................................................................................................................................... 8-10

Available Color Temperature : ........................................................................................................................................................ 8-10

Adjusting the Color Temperature.................................................................................................................................................... 8-10

Gamma ........................................................................................................................................................8-11

What can be adjusted ?...................................................................................................................................................................8-11

How to change the gamma value ? ................................................................................................................................................8-11

Decoding EBU/IRE ......................................................................................................................................8-11

What can be done ? ........................................................................................................................................................................8-11

How can it be selected ? .................................................................................................................................................................8-11

Dynamic Color Depth ..................................................................................................................................8-11

Purpose............................................................................................................................................................................................8-11

Input Balance.............................................................................................................................................. 8-12

Why adjusting the input balance ? ................................................................................................................................................. 8-12

How to adjust the input balance ? .................................................................................................................................................. 8-12

To change the Dynamic Color depth value : .................................................................................................................................. 8-12

Noise Reduction ......................................................................................................................................... 8-12

Purpose........................................................................................................................................................................................... 8-12

1-4

Table of Contents

5976277 BARCOREALITY 6400i 20042001

To change the noise reduction value : ........................................................................................................................................... 8-12

Audio Tuning............................................................................................................................................... 8-13

Available items................................................................................................................................................................................ 8-13

Volume, Balance, Bass and Treble ............................................................................................................ 8-13

How to adjust ? ............................................................................................................................................................................... 8-13

Fade............................................................................................................................................................ 8-14

Purpose........................................................................................................................................................................................... 8-14

How to set up the fade ? ................................................................................................................................................................ 8-14

Mute ............................................................................................................................................................ 8-14

Purpose........................................................................................................................................................................................... 8-14

How to stop sound reproduction ? ................................................................................................................................................. 8-14

Mode [stereo]/[mono].................................................................................................................................. 8-14

Purpose........................................................................................................................................................................................... 8-14

How to install the sound mode ? .................................................................................................................................................... 8-14

Video - Audio lock ....................................................................................................................................... 8-15

Purpose........................................................................................................................................................................................... 8-15

How to lock input source to an audio source ? .............................................................................................................................. 8-15

Geometry .................................................................................................................................................... 8-15

To start up the Geometry functions ................................................................................................................................................ 8-15

Which Geometry adjustments are possible ? ................................................................................................................................ 8-15

How can an adjustment be adjusted ?........................................................................................................................................... 8-15

Shift............................................................................................................................................................. 8-16

What can be done ? ....................................................................................................................................................................... 8-16

To start up the shift action : ............................................................................................................................................................ 8-16

Size ............................................................................................................................................................. 8-16

What can be done ? ....................................................................................................................................................................... 8-16

To start up the size adjustment : .................................................................................................................................................... 8-16

Side Keystone............................................................................................................................................. 8-17

What can be done ? ....................................................................................................................................................................... 8-17

Aligning the keystone ..................................................................................................................................................................... 8-17

Blanking ...................................................................................................................................................... 8-17

What can be done ? ....................................................................................................................................................................... 8-17

Available Blanking Adjustments ..................................................................................................................................................... 8-17

Adjusting the blanking. ................................................................................................................................................................... 8-18

Aspect Ratio [5:4]/[4:3]/[16:9] ..................................................................................................................... 8-18

Purpose........................................................................................................................................................................................... 8-18

How to setup the desired aspect ratio ? ........................................................................................................................................ 8-18

Options ....................................................................................................................................................... 8-19

How to change the geometry options ? ......................................................................................................................................... 8-19

IEEE 1394................................................................................................................................................... 8-19

Purpose........................................................................................................................................................................................... 8-19

To start up the IEEE 1394 functions............................................................................................................................................... 8-19

IEEE 1394 Control...................................................................................................................................... 8-19

To start up the IEEE 1394 control functions................................................................................................................................... 8-19

1394 Setup ................................................................................................................................................. 8-20

Purpose........................................................................................................................................................................................... 8-20

How to start up ? ............................................................................................................................................................................ 8-20

Camcorder Control ..................................................................................................................................... 8-20

Purpose........................................................................................................................................................................................... 8-20

Which functions are available? ...................................................................................................................................................... 8-20

Audiodecoding ............................................................................................................................................ 8-20

Purpose........................................................................................................................................................................................... 8-20

How to toggle ?............................................................................................................................................................................... 8-20

How to select a function ? .............................................................................................................................................................. 8-21

INSTALLATION MODE ....................................................................................................... 9-1

Installation Mode .......................................................................................................................................... 9-1

Built-up of the installation mode. ...................................................................................................................................................... 9-1

Input Slots..................................................................................................................................................... 9-1

What can be done ? ......................................................................................................................................................................... 9-1

To view or to change the input configuration : ................................................................................................................................. 9-1

Possible results for the input slots : ................................................................................................................................................. 9-2

What if a switcher is connected to the projector ? ........................................................................................................................... 9-2

No Signal ...................................................................................................................................................... 9-2

What will happen ? ........................................................................................................................................................................... 9-2

Changing the background color ....................................................................................................................................................... 9-2

1-5

Table of Contents

5976277 BARCOREALITY 6400i 20042001

Changing the shutdown setting ........................................................................................................................................................ 9-2

Lens Adjustments ......................................................................................................................................... 9-3

What can be done ? ......................................................................................................................................................................... 9-3

Zoom/Focus/Shift ............................................................................................................................................................................. 9-3

Text Box Position .......................................................................................................................................... 9-4

What can be done ? ......................................................................................................................................................................... 9-4

How to change the setting ?............................................................................................................................................................. 9-4

Quick Access Keys ....................................................................................................................................... 9-4

What can be done ? ......................................................................................................................................................................... 9-4

Getting an overview.......................................................................................................................................................................... 9-4

Factory preprogrammed keys .......................................................................................................................................................... 9-4

How to program the quick access keys (function keys) : ................................................................................................................ 9-4

Start Up mode .............................................................................................................................................. 9-5

What can be done ? ......................................................................................................................................................................... 9-5

Start up Identification........................................................................................................................................................................ 9-5

Start up Auto Power mode ............................................................................................................................................................... 9-5

Network configuration................................................................................................................................... 9-6

What can be done ? ......................................................................................................................................................................... 9-6

Set up the network configuration...................................................................................................................................................... 9-6

Entering the necessary addresses................................................................................................................................................... 9-6

800 Peripheral .............................................................................................................................................. 9-6

What can be installed ? .................................................................................................................................................................... 9-6

Defining the Output module of the RCVDS05 ................................................................................................................................. 9-6

...................................................................................................................................................................... 9-7

Defining the Infrared Communication protocol ................................................................................................................................ 9-7

Configuration ................................................................................................................................................ 9-7

What can be done ? ......................................................................................................................................................................... 9-7

Set up the Correct Configuration...................................................................................................................................................... 9-7

Available patterns ............................................................................................................................................................................. 9-8

Switching Mode ............................................................................................................................................ 9-8

What can be set up with the switching mode ? ............................................................................................................................... 9-8

OSD color (On-Screen Display) ................................................................................................................... 9-8

What can be done ? ......................................................................................................................................................................... 9-8

How to change this color setting ? ................................................................................................................................................... 9-8

Internal Patterns ........................................................................................................................................... 9-8

What can be done with these internal patterns ? ............................................................................................................................ 9-8

How to select an internal pattern ? .................................................................................................................................................. 9-8

How to install the switching mode ?................................................................................................................................................. 9-9

Shutter .......................................................................................................................................................... 9-9

What should be done ? .................................................................................................................................................................... 9-9

How to activate the shutter ? ........................................................................................................................................................... 9-9

SERVICE MODE ............................................................................................................... 10-1

Service Mode.............................................................................................................................................. 10-1

Built-up of the service mode........................................................................................................................................................... 10-1

Identification................................................................................................................................................ 10-2

What can be seen ? ....................................................................................................................................................................... 10-2

What will be indicated on the identification screen ? ..................................................................................................................... 10-2

Change Password ...................................................................................................................................... 10-3

How to enable or disable the password function ? ........................................................................................................................ 10-3

How to change the password ?...................................................................................................................................................... 10-3

Change Language ...................................................................................................................................... 10-3

Projector Address ....................................................................................................................................... 10-4

How to change that address ? ....................................................................................................................................................... 10-4

Change Projector Address.......................................................................................................................... 10-4

What can be changed ? ................................................................................................................................................................. 10-4

Start up ........................................................................................................................................................................................... 10-4

Entering the new projector address ............................................................................................................................................... 10-4

Common Address ....................................................................................................................................... 10-4

How to change that common address ? ........................................................................................................................................ 10-4

Entering the new common address................................................................................................................................................ 10-5

Change Baudrate PC ................................................................................................................................. 10-5

Reset Lamp Runtime.................................................................................................................................. 10-5

When is it allowed ?........................................................................................................................................................................ 10-5

1-6

Table of Contents

5976277 BARCOREALITY 6400i 20042001

Lamp Run Time History .............................................................................................................................. 10-5

What can be done ? ....................................................................................................................................................................... 10-5

Lamp Dimming............................................................................................................................................ 10-6

What can be done ? ....................................................................................................................................................................... 10-6

BARCO logo ............................................................................................................................................... 10-6

What can be done ? ....................................................................................................................................................................... 10-6

How to add the BARCO logo or to change a setting ? .................................................................................................................. 10-6

Available settings............................................................................................................................................................................ 10-7

Panel Adjustments...................................................................................................................................... 10-7

Warning........................................................................................................................................................................................... 10-7

Uniformity.................................................................................................................................................... 10-7

Warning........................................................................................................................................................................................... 10-7

Preset Input Balance .................................................................................................................................. 10-8

Warning........................................................................................................................................................................................... 10-8

I2C Diagnosis ............................................................................................................................................. 10-8

What can be done ? ....................................................................................................................................................................... 10-8

How to start the I2C diagnosis ? .................................................................................................................................................... 10-8

STANDARD SOURCE SET UP FILES ...............................................................................A-1

SOURCE NUMBERS 81 - 86 AND 91 - 96 ........................................................................B-1

BARCO CONTROL MANAGER .........................................................................................C-1

Control Manager ...........................................................................................................................................C-1

Functionality...................................................................................................................................................................................... C-1

Computer requirements.................................................................................................................................................................... C-1

Embedded projector software .......................................................................................................................................................... C-1

About the control manager ...........................................................................................................................C-1

Information on the Start Up page. ....................................................................................................................................................C-1

Control manager Start Page.........................................................................................................................C-2

Starting up the control manager ....................................................................................................................................................... C-2

Using the default window ................................................................................................................................................................. C-2

Control ..........................................................................................................................................................C-3

Available items.................................................................................................................................................................................. C-3

Security .............................................................................................................................................................................................C-4

General Control ................................................................................................................................................................................ C-4

Source............................................................................................................................................................................................... C-5

Image Settings.................................................................................................................................................................................. C-5

Image Enhancement ........................................................................................................................................................................ C-6

Lens adjustment ...............................................................................................................................................................................C-7

Geometry adjustment ....................................................................................................................................................................... C-7

Blanking adjustment ......................................................................................................................................................................... C-8

Audio adjustment .............................................................................................................................................................................. C-9

Configuration ................................................................................................................................................C-9

Available items................................................................................................................................................................................ C-10

Mail Setup ....................................................................................................................................................................................... C-11

Date & Time ....................................................................................................................................................................................C-13

Settings ...........................................................................................................................................................................................C-14

Source.............................................................................................................................................................................................C-14

Diagnostics .................................................................................................................................................C-15

Available items................................................................................................................................................................................ C-15

General Status................................................................................................................................................................................ C-16

Job Log ...........................................................................................................................................................................................C-16

Advanced Diagnostics .................................................................................................................................................................... C-16

CLEANING THE DUST FILTER..........................................................................................D-1

INDEX ....................................................................................................................................I-1

2-1

Packaging and Dimensions

5976183 BARCOREALITY 6400i 20042001

234

379

Pull

To open

PACKAGING AND DIMENSIONS

Projector Packaging

Way of Packaging

The projector is packed in a carton box. To provide protection during transportation, the projector is surrounded with foam. The

package is secured with banding and fastening clips.

To unpack

First release the fastening clips and remove the banding. Handle as shown in the drawing.

Take the projector out of its shipping carton and place it on a table.

Hint

Save the original shipping carton and packing material, they will be necessary if you ever have to ship your projector. For maximum

protection, repack your projector as it was originally packed at the factory.

Contents of the complete unit (box) :

- 1 remote control unit RCU + 2 batteries.

- 1 power cable with outlet plug type CEE7 or ANSI 73.11 .

- 1 owners manual

- 1 safety manual

Lens Packaging

Way of Packaging

Lenses are supplied as an individual item.

They are packed in a carton.

- 1 BARCOREALITY 6400i or 6400i DLC (weight ± 17 kg or ± 37.4 lbs)

2-2

Packaging and Dimensions

5976277 BARCOREALITY 6400i 20042001

46 82.7 211.4 169.5

139.6 14

148.9 380.6

526.8

124.1

217.2

147.8

124.4

184.4

368.7

187.2

202.4

371.2 53.5 29.6

53.5

97.6 120.2

245.1

152.6 152.6

107.5

min 12

max 24

Projector Case

Dimensions

The dimensions are given in mm.

25.4 mm = 1"

3-1

Installation Guidelines

5976277 BARCOREALITY 6400i 20042001

3INSTALLATION GUIDELINES

Safety warning

Before installing the projector, read first the safety instructions

Installation Guidelines

Ambient Temperature Conditions

Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical

to the optimum use of the projection system.

Max. ambient temperature : 40 °C or 104 °F

Min. ambient temperature : 0 °C or 32 °F

The projector will not operate if ambient air temperature falls outside this range (0°C- 40°C or 32°F-104°F).

Environment

Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight,

excessive dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not

excessive.

Environment condition check

Warning: Harmful Environmental Contamination Precaution

A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation inlets. For

installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines or

similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading

performance), then it is highly advisable and desirable to have this contamination removed prior to it reaching the projectors clean

air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not

a feasible solution then measures to relocate the projector to a clean air environment should be considered.

Only ever use the manufactures recommended cleaning kit which has been specifically designed for cleaning optical parts, never

use industrial strength cleaners on a projectors optics as these will degrade optical coatings and damage sensitive optoelectronic

components. Failure to take suitable precautions to protect the projector from the effects of persistant and prolonged air contaminants

will culminate in extensive and irreversible ingrained optical damage. At this stage cleaning of the internal optical units will be non-

effective and impracticable. Damage of this nature is under no circumstances covered under the manufactures warranty and may

deem the warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any repair.

It is the clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne particles

in the environment of the projector. The manufacture reserves the right to refuse repair if a projector has been subject to wantful

neglect, abandon or improper use.

What about ambient light ?

The ambient light level of any room is made up of direct or indirect sunlight and the light fixtures in the room. The amount of ambient

light will determine how bright the image will appear. So, avoid direct light on the screen.

Windows that face the screen should be covered by opaque drapery while the set is being viewed. It is desirable to install the projection

system in a room whose walls and floor are of non-reflecting material. The use of recessed ceiling lights and a method of dimming

those lights to an acceptable level is also important. Too much ambient light will wash out of the projected image. This appears as

less contrast between the darkest and lightest parts of the image. With bigger screens, the wash out becomes more important.

As a general rule, darken the room to the point where there is just sufficient light to read or write comfortably. Spot lighting is desirable

for illuminating small areas so that interference with the screen is minimal.

3-2

Installation Guidelines

5976277 BARCOREALITY 6400i 20042001

Which screen type?

There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear

projection applications.

Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount

of light projected toward them. The GAIN of a screen is the term used. Front and rear screens are both rated in terms of gain. The

gain of screens range from a white matte screen with a gain of 1 (x1) to a brushed aluminized screen with a gain of 10 (x10) or

more. The choice between higher and lower gain screens is largely a matter of personal preference and another consideration called

the Viewing angle.

In considering the type of screen to choose, determine where the viewers will be located and go for the highest gain screen possible.

A high gain screen will provide a brighter picture but reduce the viewing angle.

For more information about screens, contact your local screen supplier.

A high gain screen will provide a brighter picture but reduce the viewing angle.

What image size? How big should the image be?

The projector is designed for projecting an image size (video) from 1.00m (3.3ft) to 6.00m (19.7ft) with a aspect ratio of 5 to 4.

Projector Configurations

Which configuration can be used ?

The projector can be installed to project images in four different configurations :

Front/table

Rear/table

Front/ceiling or

Rear/ceiling

Front/Table

Front/Ceiling

Rear/Table

Rear/Ceiling

Positioning the Projector

Drawing are given for a nominal lens position.

Definitions of the Abbreviation on drawings

B = Distance between ceiling and top of the screen or between floor and bottom of the screen.

A = Correction value, distance between bottom side of projector (without feet) and middle of the lens. Value to be subtracted from

B to obtain the correct installation position. (A value is a constant value for all screen widths and type of lenses, A = 124.1 mm or

4.89 inch)

CD = Total distance between projector and ceiling or projector and floor.

SW = Screen width.

SH = Screen height (image height).

PD = Projector Distance, distance between screen and projector.

3-3

Installation Guidelines

5976277 BARCOREALITY 6400i 20042001

Screen

Floor

Projector

CD = B - A

Optical axis projection lens

SIDE VIEW

BACK VIEW

Screen

TOP VIEW

Floor

Screen

Floor

Projector

A’

D = B - A

SH Optical axis projection lens

SIDE VIEW

ACK VIEW

Screen

TOP VIEW

Floor

OFF-Axis installation ON-Axis installation

Lenses

Which lens has to be selected.

1 Determine the required screen width.

2 Determine the approximate position of the projector in the projection room with regard to the screen and measure the

projector-screen distance (PD).

3 Use the lens formulas to find the best corresponding PD with regard to the measured projector-screen distance for the required

screen width.

The desired lens is determined.

Available lenses

The projector is supplied without any lens.

The following lenses are available, or will become available (contact a Barco service center) as an option :

Lenses Standard version

QFD(1.27:1) R9840400

QFD(2.5:1) R9840290

QFD(1.4-2.1:1) R9840380

QFD(2.1-3.0:1) R9840390

QGD(3.5-4.5:1) R9840060

QFD(4.5-6.0:1) R9840100

QFD(7:1) R9840410

3-4

Installation Guidelines

5976277 BARCOREALITY 6400i 20042001

Image 1 Image 2

Lens formulas to calculate the projector distance.

Metric formulas (meter) Inch formulas (inch)

QFD(1.27:1) PD = 1.29 x SW - 0.0195 + 0.00276/SW PD = 1.29 x SW - 0.77 + 42.78/SW

QFD(2.5:1) PD = 1.324 x SW - 0.065 + 0.0297/SW PD = 1.324 x SW - 0.77 + 46.03/SW

QFD(1.4-2.1:1) PDmin=1.44 x SW + 0.0287 - 0.022/SW PDmin=1.44 x SW + 1.3 - 34.10/SW

PDmax=2.20 x SW - 0.01 + 0.02/SW PDmax=2.20 x SW - 0.39 + 31.0/SW

QFD(2.1-3.0:1) PDmin = 2.13 x SW - 0.10 + 0.056/SW PDmin = 2.13 x SW - 0.39 + 86.80/SW

PDmax = 2.90 x SW + 0.10 - 0.0745/SW PDmax = 2.90 x SW + 0.39 - 115.47/SW

QFD(3.5-4.5:1) PDmin = 3.374 x SW - 0.115 + 0.0575/SW PDmin = 3.374 x SW - 4.53 + 89.12/SW

PDmax = 4.433 x SW - 0.133 + 0.0556/SW PDmax = 4.433 x SW - 5.24 + 86.18/SW

QFD(4.5-6.0:1) PDmin = 4.29 x SW - 0.02 + 0.0009/SW PDmin = 4.29 x SW - 0.79 + 1.395/SW

PDmax = 5.86 x SW + 0.15 + 0.0121/SW PDmax = 5.86 x SW + 5.91 + 18.755/SW

QFD(7.0:1) Metric PD = 7.021 x SW + 0.047 + 0.0093/SW PD = 7.021 x SW + 1.85 + 14.41/SW

Lens program to calculate the projector distance is available on the BARCO webside :

http://www.barco.com/projection_systems/customer_services/lens_program.asp

How to install the lens?

Follow the next procedure :

1. Take the lens out of its packing material.

2. Open the lens cover of the projector by pivoting it up and take it off (image 1).

3. Open both lens locks (B) by pulling them backwards. Unlock first by pulling clip (A) forwards (image 2).

4. Put the lens on the lens holder.

5. Fix the lens by closing both locks (B) until they are secured (image 3).

6. Plug the wires of motor unit into the connector (C) (image 3).

7. Re-install the lens cover (image 4)

3-5

Installation Guidelines

5976277 BARCOREALITY 6400i 20042001

Image 4

Cleaning the Lens

To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have developed recommendations

for cleaning the lens. FIRST, we recommend you try to remove any material from the lens by blowing it off with clean, dry deionized

air. DO NOT use any liquid to clean the lenses.

A TorayseeTM cloth is included with the lens kit.

Proceed as follows :

1. Always wipe lenses with a CLEAN TorayseeTM cloth.

2. Always wipe lenses in a single direction. Do not wipe back and forwards across the lens surface as this tends to grind dirt into

the coating.

3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.

4. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.

5. Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the cloth.

6. Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.

Order number for a new TorayseeTM cloth : R379058.

Other lenses can also be cleaned safely with this TorayseeTM cloth.

Battery installation in the RCU.

Inserting the Batteries.

Two batteries are packed together with the RCU. Before using your RCU, install first these batteries.

1 Remove the battery cover on the backside by pushing the handle a little towards the bottom of the RCU.

2 Lift up the top side of the cover at the same time.

3 Insert the batteries as indicated in the RCU.

4 Put the battery cover on its place.

Image 3

3-6

Installation Guidelines

5976277 BARCOREALITY 6400i 20042001

Note

Note, only important if more than one projector is installed in the room :

1. The common address can be zero (0) or one (1). The standard RCU are setup for common address zero. To change the common

address of the RCU, contact a BARCO service center. If it is necessary to program the projector address into the RCU, see chapter

'Getting Started'.

2. Projector address has to be reprogrammed everytime the battery is changed, the RCU will always switch to the default address.

How to replace the batteries in the RCU ?

To replace the batteries :

1 Remove the battery cover on the backside by pushing the handle a little towards the bottom of the RCU.

2 Lift up the top side of the cover at the same time.

3 Push on the + side of the battery towards the - side

4 Lift up the battery at the same time.

5 Repeat for the second battery.

6 Insert the batteries as indicated in the RCU (battery type AA or LR6 or equivalent).

7 Put the battery cover on its place.

4-1

Connections

5976277 BARCOREALITY 6400i 20042001

SDI SDO

S-VIDEO

VIDEO

COMPUTER

IEEE 1394 10/100BASE-TMOUSE

MONITOR

RS232 IN RS232 OUT

AUDIO IN AUDIO IN AUDIO IN AUDIO IN

COMM. PORT RC

RGB H/CV

SDI

S-VIDEO

VIDEO 43

Fuses

Warning

For continued protection against fire hazard :

- refer replacement to qualified service personnel

- ask to replace with the same type of fuse.

Fuse type : T10 AH/250V

Switching on

Use the power switch to switch on.

When '0' is visible, the projector is switched off.

When '1' is visible, the projector is switched on.

When switching on with the power switch, the projector starts in the stand by mode. The projector mode indication lamp is red.

CONNECTIONS

Power connection to Projector

AC Power (mains) cord connection

Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector

at the front of the projector.

The power input is auto-ranging from 90 to 240 VAC.

4-2

Connections

5976277 BARCOREALITY 6400i 20042001

Projector mode indication

F1 F2 F3 F4 F5

ADJ EXIT

ENTER

PAUSE

PHASE

TEXT

SHARPN

TINT

COLOR

BRIGHTN

CONTR

TREBLE BALANCE

BASS VOL

COLORPHASE

SHARPN TINT BRIGHTN

STANDBY

ENTER

TEXT

EXIT

PAUSE

CONTRAST

Stand-by key

Lamp Run Time

When the total run time of the lamp is 970 hours or more, the following warning message will be displayed for 1 minute. This warning

message will be repeated every 30 minutes. Press EXIT to remove the message before the minute is over.

Remaining

Lamp run time

20 h

<ENTER> to continue

WARNING

Lamp run time is 1000 hours

Operating the lamp longer

than 8000 hours may damage

the projector.

Please replace the lamp

Saving data, Please wait

To start image projection :

a. press the 'Stand by' button once on the local keypad or on the remote control. The projector mode indication lamp will be green.

b. press a digit button to select an input source. The projector mode indication lamp will be green.

When the total run time of the lamp is 1000 hours or more, the following warning message, with the exact run time is displayed on

the screen.

Lamp run time is 1000 hours. Operating the lamp longer than 1000 hours may damage the projector. Please replace the lamp.

When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min.

The total lifetime of the lamp for a safe operation is 1000 hours max. Do not use it longer. Always replace with a same type of lamp.

Call a BARCO authorized service technician for lamp replacement.

Lamp Run Time Warning

Using a lamp for more than 1000 hours is dangerous as the lamp could explode.

Switching to Stand-by.

When the projector is running and you want to go to stand-by, press the stand-by key for 2 seconds until the message 'Saving data,

please wait' is displayed. Do not press any longer on the standby key otherwise the projector will restart.

4-3

Connections

5976277 BARCOREALITY 6400i 20042001

Switching Off

To switch off:

- First press STANDBY key for 2 seconds. When the message 'Saving data, please wait' is displayed, do not press any longer on

the standby key otherwise the projector will restart. Let cool down the projector at least 10 min.

- Switch off the projector with the power switch.

Switching to Stand-by Warning

When switching to standby, it is possible to restart within the first 5sec.. When not restarted within these first 5 sec.,

the projector waits for 1 min. to restart again. During this period the LED display will show a jumping square with a dash.

After one minute, two dashes will be displayed and the projector can restart.

Input Source Connection

Input facilities

5-cable input

Computer

Video

S-Video

Serial digital input

IEEE 1394 (optional)

Input Selection

This can be manually or automatically.

When 'automatic' is selected in the Input slots menu, by starting up the projector, it searches for an input source by scanning the

inputs one by one. If only one source is found, this source will be projected. If different sources are found, the priority is as follow:

1. Video

2. S-Video

3. 5 Cable input

4. Computer input

SDI input and IEEE input are never automatically selected.

Note : When a RCVDS is connected to the projector,

the 'Automatic' selection is disabled.

Set up of the input selection

1 Press ENTER to start up the adjustment mode.

2 Press the cursor key é or ê to select 'Installation' (menu 1).

3 Press ENTER to display the Installation menu.

4 Press the cursor key é or ê to select 'Input Slots' (menu 2).

5 Press ENTER to display the Input slots menu.

6 Press the cursor key é or ê to select 'Input Slots' (menu 3).

7 Press ENTER to toggle between [Manual] or [Automatic].

8 Press EXIT several times to leave the adjustment mode.

Select with ê or é

then <ENTER>

<EXIT> to return.

Select with ê or é

then <ENTER>

<EXIT> to return.

INSTALLATION

INPUT SLOTS

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

INPUT SLOTS

SLOT SELECTOR [Automatic]

x 1. RGB [HS&VS]

- 2. RGB [HS&VS]

- 3. VIDEO

- 4. S-VIDEO

- 5. DIGITAL INPUT

- 6. IEEE 1394

Select with ê or é

<ENTER> to toggle

<EXIT> to return.

menu 1 menu 2 menu 3

Input Facilities, RCVDS05 connected.

When using a RCVDS05, it is recommended to use a 5-cable output module in the RCVDS. The outputs of this module have to be

connected to the 5 cable input (slot 1) of the projector.

To switch the projector in the 5-cable mode see chapter 'Installation mode'.

4-4

Connections

5976277 BARCOREALITY 6400i 20042001

SDI SDO

S-VIDEO

VIDEO

COMPUTER

IEEE 1394

MONITOR

RGB H/CV

10/100

MOUSE

Select with ê or é

then <ENTER>

<EXIT> to return.

Select with ê or é

then <ENTER>

<EXIT> to return.

Which signals can be connected to the 5-cable input

The following signals can be connected to these BNC connectors :

Connector name R G B H V

Input signal

RGBHV R G B H V

RGBS R G B S -

RGsB R Gs B - -

Composite Video - Video - - -

Super Video - Y - - C

Component Video - SS R-Y Y B-Y S -

Component Video - SOY R-Y Y s B-Y - -

How to select input Slot 1

Key in 1 on the RCU or the local keypad.

Configuration of the 5-cable input

The configuration has to be done on the 'Input slot' menu.

To change the signal format :

1Press ADJUST or ENTER key to start up the Adjustment mode (menu 1).

2Push the cursor key é or ê to select Installation

3Press ENTER.

4Press the cursor key é or ê to select 'Input Slots' (menu 2)

5Press ENTER. The internal system will scan the inputs and displays the result in the 'Input Slots' menu.

6Push the cursor key é or ê to select the first slot (menu 3).

7Press ENTER key to toggle the input signal priority.

5-cable Input Slot (slot 1)

Slot 1 has 5 BNC input terminals.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

INSTALLATION

INPUT SLOTS

800 PERIPHIRAL

CONFIGURATION

OSD COLOR

INPUT SLOTS

SLOT SELECTOR [Automatic]

x 1. RGB [HS&VS]

- 2. RGB [HS&VS]

- 3. VIDEO

- 4. S-VIDEO

- 5. DIGITAL INPUT

- 6. IEEE 1394

Select with ê or é

then <ENTER>

<EXIT> to return.

menu 1 menu 2 menu 3

Page is loading ...

Barco BarcoReality 6400 DLC User manual

Brand: Barco

Model: BarcoReality 6400 DLC

Category: Data projectors

Type: User manual

This manual is also suitable for

Download PDF

report

Barco BarcoReality 6400 DLC User manual

This manual is also suitable for

Barco BarcoReality 6400 DLC User manual

Related papers

Other documents