Ercol 4189 Assembly Instructions

Brand: Ercol

Model: 4189

Type: Assembly Instructions

Pre-assembly preparation

Please ensure instructions are read in full before attempting to assemble this product

Necessary Tools

This item is HEAVY

Please check the pack contents before attempting to assemble this product. A full checklist of components

is given in this leaflet. If any components are missing, please contact the retailer from whom you bought

this product.

This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE

WHEN LIFTING to avoid personal injury and (or) damage to the product.

This product takes approximately 30 MINUTES to assemble with 2 PEOPLE.

The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG

CHILDREN.

Monza Dressing Table

Thank you for purchasing this Monza dressing table . Please read the instructions carefully before use to ensure safe

and satisfactory operation of this product. Installation should be carried out exactly according to the manufacturers

instructions, otherwise a safety risk can occur if incorrectly installed.

WARNING: In order to prevent overturning this product must be used with the wall attachment device provided.

Ref: 00329/4189

Fittings and parts checklist

Top & Drawer box x 1

Left leg x 1

Right leg x 1

Support Rail x 1

Mirror x 1

M6*30 Bolt x 12

Wedge x 2

Allen key x 1

Cam rod x 2

Cam head x 2

Attach the top drawer box (A) onto the left leg (B) and the right leg (C) by using the 10pcs M6*30 bolt (F)

as shown below.

back side of the eht e left leg(B) and right leg(C) onto ht hcattA .2

Step by step assembly instructions

(F) as shown below.

t(A) inu xob reward using 2pcs M6*30 bolt

Put the top drawer box (A) on another table or platform with thye bottom up.

Attach the support rail (D) onto the left leg (B) and the right leg (C) by using the cam rod (H) and

cam head (I) as shown below.

When completed please lift the unit to standing position.

3. Put the mirror(E) onto the left & right legs (B&C) as shown below.

Adjust the mirror angle freely as above using you hand directly.

Dressing table assembly completed.

4. If the dressing table is not level on your floor, use the wedges

provided. Snap them off so they do not protrude out from the

table legs. You can also snap them lengthways.

The hanger on the wooden frame of the mirror

should slot into the base on the leg rails.

Wall fixing instructions

Thank you for purchasing this ercol product.

Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.

Installation should be carried out exactly according to the manufacturer’s instructions, otherwise a safety risk can

occur if incorrectly installed.

WARNING: In order to prevent overturning this product must be used with the wall attachment device provided.

1. Place your product in the final

position. Loosen the screws on the

metal brackets just enough so that

the slotted bracket can be extended

to meet the wall.

2. Then re-secure the screws.

3. Mark the wall for drilling through

the hole in the short face of the

bracket.

Then remove the unit from the wall

so that the marked holes can be

drilled.

Ensure you use an appropriate fixing

type for your wall (see page 6). Then

return the unit to position.

4. Secure the unit to the wall fixings

with own screws through the

brackets.

Warning

Serious or fatal crushing injuries can occur from furniture tipping over.

To prevent this furniture tipping over it must be permanently fixed to the wall.

5. Tighten the screws and then f ixings

assemble completed.

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

Ercol Furniture Ltd, Summerleys Road, Princes Risborough, Buckinghamshire. HP27 9PX www.ercol.com

Types of walls

You can use one of the following types of wall plug if your walls are made of

brick, breezeblock, concrete, stone or wood.

1. General Purpose wall plug

Generally aerated blocks should not be used to support heavy loads, use a

specialist fitting in this case. For light loads, general - purpose wall plugs can

be used.

2. Plasterboard wall plug

For use when attaching light loads on to plasterboard partitions.

3. Cavity Fixing wall plug

For use with plasterboard partitions or hollow wooden doors.

4. Cavity Fixing - Heavy Duty wall plug

For use when fitting or supporting heavy loads such as shelving, wall

cabinets and coat racks.

5. Hammer Fixing wall plug

For use with walls stuck with plasterboard. The hammer fixing allows it to

be fixed to the wall rather than the plasterboard. Always check the fixing is

secure to the retaining wall.

6. Shield Anchor wall plug - Heavy loads

For use with heavier loads such as TV and Hi-Fi speakers and satellite dishes

etc.

Safety: Periodically check all fittings and wall fixings to ensure they

have not come loose and retighten as necessary.

Wall attached item only.

A guide to wall mounting and fixings

Warning

Serious or fatal crushing injuries can occur from furniture tipping over.

To prevent this furniture from tipping over it must be permanantly fixed to the wall.

Wall fixing screws are not included, since different wall materials require different types of screws / fixings.

Please ensure you use the correct screws / fixings for your type of walls and seek professional advice if you

are not sure.

Failure of the product due to incorrect fixings is the responsibility of the installer.

Important: When drilling into the walls always check that there are no hidden wires or pipes etc.

Ercol 4189 Assembly Instructions

Brand: Ercol

Model: 4189

Type: Assembly Instructions

Download PDF

report

Ercol 4189 Assembly Instructions

Ercol 4189 Assembly Instructions

Related papers

Other documents