MrSteam Recessed Light Installation guide

Brand: MrSteam

Model: Recessed Light

Type: Installation guide

MrSteam Recessed Light is a practical and safe solution for adding light to your steam room. It's a NON-IC rated fixture, suitable for a maximum ceiling thickness of 1.5 inches. The light comes fully assembled and can be installed in 10 easy steps. It requires a 5 1/4" diameter hole in the ceiling and can be used with a 50W PAR30L Halogen Bulb (or energy-efficient equivalent), which is included in the kit. The light features a moisture seal to protect it from the steam and humidity of the steam room environment.

The MrSteam Recessed Light is a NON-IC rated fixture.

IMPORTANT NOTES:

•The MrSteam®recessed light is for ceiling mount only.

• Read all instructions before starting installation.

Keep instructions for future reference.

• Install the Recessed light in accordance with

National and local electrical codes.

• A wall switch, or dimmer switch, must be used

to turn the recessed light on and off.

• Installation to be performed by a qualified and licensed

electrician. The Recessed light operates on 120 volts.

• Do not install the wall switch in the

steam room. The switch must be

installed in a location and manner

described in the NEC and local

electric codes.

• Ensure that the power is not

supplied to the field wiring

during installation, turn off power

at the breaker panel, or remove

the fuse at the fuse box.

.steam®MS/CU LIGHT RCS

___________________________________________________________________________________________________________________________________________

I N S TA L L AT I O N I N S T R U C T I O N S

PUR 100487 9.18

.steam®

Sussman-Automatic Corp®

[email protected] www.mrsteam.com

43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM fax: 718 472 3256

9410 S. La Cienega Blvd., Inglewood, CA 90301 tel: 1 800 72 STEAM fax: 310 216 2944

All drawings are for illustrative purposes

only (all dimensions in inches).

!WA RNIN GS :

!CA UT IO N

states a hazard

which may cause serious injury or death

if precautions are not followed.

IMPORTANT NOTE:

As you follow these instructions, you will notice

warning and caution symbols. This information is important for the safe

and efficient installation and operation of this light. These are types of

potential hazards that may occur during this installation and operation:

signals a situation where

minor injury or product damage may occur

if you do not follow instructions.

Warranty:

To view or download the MrSteam®warranty

and register your product go to

blog.mrsteam.com/wr

12.25

6.25

1.8 (maximum

ceiling thickness:1.5)

J-Box

Housing

Trim

Lens Assembly

Sleeve

Lens

Assembly

Screws (4)

13.75

11.75

5.078

Mounting

Bracket

!CA UT IO N

!WA RN IN G

RECESSED LIGHT FIXTURE

BLACK

(Hot)

WHITE

(Neutral)

GREEN

(Ground)

THERMAL

PROTECTOR Bulb

Socket

Wiring Diagram

.steam®MS/CU LIGHT RCS

_________________________________________________________________________________________________________________________________________________________________

INSTALLATION INSTRUCTIONS

All drawings are for illustrative purposes only

PUR 100487 9.18

Hanger Bars

Ceiling Beams

Mounting

Bracket

Hanger Bars

INSTALLATION:

The MrSteam Recessed Light is a NON-IC rated fixture.

1. The lighting fixture comes fully assembled. Do not

disassemble except as shown for installation.

2. A 5 1⁄4" diameter hole is required in the finished

ceiling for the recessed light.

3. The recessed light is suitable for a maximum ceiling

thickness of 11⁄2".

4. Insert hanger bars into the mounting brackets and

rotate to lock them into the groves as shown.

5. Secure the housing to the ceiling beams as required so

the bottom of the lens assembly sleeve is flush with the

finished face of the ceiling.

6. Affix the hanger bars to a sturdy surface such as a joist

or cross beam. It is the contractor's responsibility to

supply proper mounting based on job condition.

7. Utilize the conduit entries on the sides of the J-box for

wiring. CONNECT GREEN WIRE TO “GROUND”,

CONNECT BLACK FIXTURE TO BLACK BUILDING

WIRE AND CONNECT WHITE FIXTURE WIRE TO

WHITE BUILDING WIRE as shown in wiring diagram.

All connections should be contained inside the

junction box.

IMPORTANT NOTE: In older buildings it is always

good practice to confirm the wiring polarity.

8. Install the 50W PAR30L Halogen Bulb (or energy

efficient equivalent) included in the kit by screwing it

into the socket while the power is turned off.

9. Apply a bead of silicone around the outer edge of the

lens before being lifted into place. Apply silicone as

required for a 360 degree moisture seal.

10. Affix the lens assembly with reflector to housing

using the 4 allen head screws provided.

BULB REPLACEMENT:

1. Turn power to the lighting fixture off.

2. Use only a 50W PAR30L Halogen bulb (or energy efficient

equivalent) for replacement purposes.

3. Remove the lens assembly with reflector to access the bulb

4. Once the new bulb is replaced apply new silicone and

follow installation steps 9 and 10 to reconnect the lens assembly.

!CAU TI ON

MrSteam Recessed Light Installation guide

MrSteam Recessed Light Installation guide

MrSteam Recessed Light Installation guide

Related papers

Other documents