Garmin Girouette anemometre GWS 10 Installation guide

installation instructions (EN)

instructions d’installation (FR)

istruzioni di installazione (IT)

installationsanweisungen (DE)

instrucciones de instalación (ES)

installationsvejledning (DA)

installeringsinstruksjoner (NO)

installationsinstruktioner (SV)







July 2013 190-01169-92_0C Printed In Taiwan

Page is loading ...

3GWS 10 Installation Instructions







To obtain the best possible performance, install your GWS 10 Wind Sensor according to the following instructions. If you experience difculty

during the installation, contact Garmin

®

Product Support, or seek the advice of a professional installer.

The GWS 10 communicates with NMEA 2000

®

-compatible chartplotters and displays. Refer to www.garmin.com for a list of compatible

devices and for more information about NMEA 2000.

 If you are unfamiliar with NMEA 2000, be sure to read the “NMEA 2000 Network Fundamentals” chapter of the Technical Reference

for Garmin NMEA 2000 Products on the included CD (GWS 10 with GMI™ bundle package only) or click on the “Manuals” hyperlink on the

GWS 10 page at www.garmin.com.





See the Important Safety and Product Information guide in the product box for product warnings and other important information.





Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.

Use caution when working from heights.

Notice

When drilling or cutting, always check the opposite side of the surface. Be aware of fuel tanks, electrical cables, and hydraulic hoses.

Connect the gray in-line lightning arrestor to help prevent lightning strike-related damage to the NMEA 2000 network. The lightning arrestor

is designed to help prevent damage due to nearby lightning strikes, but it is not able to protect against direct lightning strikes. Garmin is not

responsible for lightning strike-related damage.



Before installing your unit, conrm that your package includes the following items. If any parts are missing, contact your Garmin dealer

immediately.



• GWS 10 Wind Sensor unit (and anemometer cups)

• GWS 10 Wind Sensor mounting hardware (screws)

• GWS 10 documentation

• NMEA 2000 hardware (see below)



• GWS 10 basic package

• GMI unit with protective cover

• GMI ush-mount hardware (screws)

• GMI NMEA 0183 data wiring harness

• GMI documentation

• NMEA 2000 hardware (see below)



NMEA 2000 female terminator

(supplied in the GWS 10 with GMI

bundle package only)

NMEA 2000 inline terminator (black)

NMEA 2000 lightning arrestor (gray)

NMEA 2000 male eld-installable

connector

NMEA 2000 T-connector (2)

(supplied in the GWS 10 with

GMI bundle package only)

NMEA 2000 backbone cable

• 30 meter spool (98.5 feet)

• Requires the included eld-installable male NMEA 2000 connector.

NMEA 2000 drop-cable

• 2 meters (6.5 feet)

• Supplied in the GWS 10 with GMI bundle package only

NMEA 2000 power cable (yellow)

• 2 meters (6.5 feet) (3 A fuse included)

• Supplied in the GWS 10 with GMI bundle package only

4 GWS 10 Installation Instructions



• Phillips screwdriver

• Drill and

1

/

8

in. (3.3 mm) drill bit



• Additional NMEA 2000 network components



If you purchased the GWS 10 with GMI bundle package, use the included GMI Installation Instructions to install the GMI.



1. Ensure that the shaft lines up correctly with the slot on the anemometer. The socket on the

anemometer only ts one way on the shaft.

2. Press on the anemometer until it is seated securely.

 After the wind sensor is assembled, disassemble it for repair purposes only.



1. Route the bare-wire end of the NMEA 2000 backbone cable downward inside or along the

mast, leaving an appropriate amount of slack.

2. Drill

1

/

8

in. (3.3 mm) pilot holes and use the provided screws to mount the GWS 10 in the

appropriate orientation (refer to the diagram). If there is not a horizontal surface at the top of

the mast, fashion a wedge to mount the unit horizontally.

Use the included adhesive-backed mounting template to help position the pilot holes.

3. At the top of the mast, connect the in-line terminator to the backbone cable and to the GWS 10.

4. Secure the in-line terminator to the mast with the provided screws.

5. Pull the cable at the bottom of the mast to remove the slack.

6. Run the bare-wire end of the cable to the existing NMEA 2000 network or to the area where the

NMEA 2000 network will be installed.

 If you do not mount the GWS 10 facing the exact front of the boat, congure the software

to the appropriate wind-angle offset (page 5).



1. Cut the NMEA 2000 backbone cable to the proper length. Ensure that the cable reaches the existing NMEA 2000 network, and leave enough

slack cable for routing and attaching the eld-installable connector.

2. Assemble and wire the eld-installable connector as shown in the diagrams.



NMEA 2000 backbone cable

NMEA 2000 wires





1

2

3

4

Blue (center)

Red

Bare wire

White

Black

3. Attach the eld-installable connector to the gray in-line lightning arrestor.

4. Disconnect the male terminator from the backbone of the existing NMEA 2000 network on your boat.

Notice

Connect the gray in-line lightning arrestor to help prevent lightning strike-related damage to the NMEA 2000 network. The lightning arrestor

is designed to help prevent damage due to nearby lightning strikes, but it is not able to protect against direct lightning strikes. Garmin is not

responsible for lightning strike-related damage.

5. Connect the in-line lightning arrestor to the T-connector at the location from which you removed the male terminator in step 3.



If you do not have an existing NMEA 2000 network, you must install a NMEA 2000 network on your boat to use the GWS 10. For more

information on NMEA 2000, visit www.garmin.com.

Anemometer

Front of the boat







5GWS 10 Installation Instructions

1. Connect the two included T-connectors together by their sides.

2. The NMEA 2000 power cable must be connected to a 9–16 Vdc power source through the ignition switch of the boat or through an

appropriate additional switch (not included).

Notice

Connect the included NMEA 2000 power cable to the ignition switch of the boat or through an external switch. The NMEA 2000 network will

drain the boat battery if it is connected directly to the battery.

3. Connect the NMEA 2000 power cable to one of the two T-connectors.

4. Connect the included NMEA 2000 drop cable to the other T-connector and to the GMI.

5. Add additional T-connectors (not included) for each additional sensor or display device (not included) that is added to the NMEA 2000

network, and connect each sensor or display device to a T-connector with the appropriate drop cable (not included).

6. Connect the female terminator to the appropriate end of the combined T-connectors.



+

-

GMI

GWS 10

NMEA 2000

power cable

9–16 Vdc

Female

terminator

T-connectors

Drop cable

In-line lightning

arrestor

Field-installable

connector

30 m (98.5 ft.)

backbone cable

(cut to length)

In-line terminator

External switch

(not included)



Refer to your Garmin Chartplotter or marine instrument owner’s manual for specic instructions regarding conguring NMEA 2000 devices.



1. Select  if you did not orient the GWS 10 facing the exact front of the boat.

2. Select the angle (in degrees) to adjust for the difference in orientation.

The angle is congured clockwise around the mast of the boat. For example, 90 degrees is starboard, and 270 degrees is port.



1. Select .

2. Choose from the following settings to adjust the lter:

• —turn off the lter to make the display more responsive to changes in the wind angle.

• —select a higher number to increase the responsiveness of the display to changes in the wind angle, or select a lower number to

decrease the responsiveness.

• —automatically adjusts the lter settings based on wind conditions.

6 GWS 10 Installation Instructions



1. Select .

2. Choose from the following settings to adjust the lter:

• — turn off the lter to make the display more responsive to changes in the wind speed.

• —select a higher number to increase the responsiveness of the display to changes in the wind speed, or select a lower number to

decrease the responsiveness.

• —automatically adjusts the lter settings based on wind conditions.



Refer to your Garmin Chartplotter or marine instrument owner’s manual for instructions regarding conguring NMEA 2000 devices.



1. Calculate the degree of offset of the GWS 10 from the front of the boat.

 : The angle is calculated clockwise around the mast of the boat. For example, 90 degrees is starboard while 270 degrees is port

2. Select  to specify data for the lter and offset settings.

3. Enter:  followed by the value you calculated in step 1 (for example: ANGLEOFFSET=180).



1. Calculate the time constant value for the wind angle lter.

: The time constant value is a number between 0 and 254, which represents the amount of time, in quarter-second increments, that the

wind angle must change before it is updated on your display. For example, a value of 40 means that the display will not update the wind

angle unless it changes for more than 10 seconds. To use the Auto setting, which adjusts the lter automatically based on wind conditions,

use a value of 255.

2. Select  to specify data for the lter and offset settings.

3. Enter the following command:  followed by the value you calculated in step 1 (for example: “ANGLEFILTER=12”).



1. Calculate a time constant value for the wind speed lter.

: The time constant value is a number between 0 and 254, which represents the amount of time, in quarter-second increments, that the

wind speed must change before it is updated on your display. For example, a value of 40 means that the display will not update the wind

speed unless it changes for more than 10 seconds. To use the Auto setting, which adjusts the lter automatically based on wind conditions,

use a value of 255.

2. Select  to specify data for the lter and offset settings.

3. Enter the following command: followed by the value you calculated in step 1 (for example: “SPEEDFILTER=215”).



Use the tables to determine the approved NMEA 2000 PGN information that can be received and transmitted by a GWS 10 when

communicating with a NMEA 2000-compliant device.

 

059392 ISO Acknowledgment 059392 ISO Acknowledgment

060928 ISO Address Claim 059904 ISO Request

126208 NMEA - Command/Request/

Acknowledge Group Function

060928 ISO Address Claim

126464 Transmit/Receive PGN List Group

Function

126208 NMEA - Command/Request/

Acknowledge Group Function

126996 Product Information

The GWS 10 is NMEA 2000

certied

130306 Wind Data

130312 Temperature

130314 Actual Pressure

7GWS 10 Installation Instructions





 The width of this sensor varies with the positioning of the

wind vane.

 W × H × D: 19

11

/

16

–22

5

/

8

× 11

1

/

32

× 5

1

/

2

in.

(500–575 × 280 × 140 mm)

 0.6 lb. (0.275 kg)

 Attached NMEA 2000 cable length is 18 in. (46 cm)

 From 5°F to 158°F (from -15°C to 70°C)



 Housing and Base: PC/ABS

 Wind vane and Anemometer: Polypropylene

Tubing: 6063 Aluminum

Shafts:304 SS



  9–16 Vdc via NMEA 2000

 2 (100 mA)



If you have an existing NMEA 2000 network and a NMEA 2000-compatible Garmin chartplotter, ensure that you have updated the software on

all devices to the latest version. For more information, refer to www.garmin.com.

If you have an existing NMEA 2000 network and do not have a NMEA 2000-compatible Garmin chartplotter, contact Garmin product support

or locate a Garmin dealer.



Help us better support you by completing our online registration at www.garmin.com/registration/. Go to http://my.garmin.com. Keep the

original sales receipt, or a photocopy, in a safe place.

For future reference, write the serial number assigned to your GWS 10 in the space provided. It is located on a sticker on the unit.

Serial number



Contact Garmin Product Support if you have any questions while using your GWS 10. In the USA, go to www.garmin.com/support, or contact

Garmin USA by phone at (913) 397-8200 or (800) 800-1020.

In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.

In Europe, go to www.garmin.com/support and click  for in-country support information, or contact Garmin (Europe) Ltd. by

phone at +44 (0) 870.8501241.



BY USING THE GWS 10, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE AGREEMENT. PLEASE

READ THIS AGREEMENT CAREFULLY.

Garmin Ltd. and its subsidiaries (“Garmin”) grant you a limited license to use the software embedded in this device (the “Software”) in binary executable form in the normal

operation of the product. Title, ownership rights, and intellectual property rights in and to the Software remain in Garmin and/or its third-party providers.

You acknowledge that the Software is the property of Garmin and/or its third-party providers and is protected under the United States of America copyright laws and

international copyright treaties. You further acknowledge that the structure, organization, and code of the Software, for which source code is not provided, are valuable trade

secrets of Garmin and/or its third-party providers and that the Software in source code form remains a valuable trade secret of Garmin and/or its third-party providers. You

agree not to decompile, disassemble, modify, reverse assemble, reverse engineer, or reduce to human readable form the Software or any part thereof or create any derivative

works based on the Software. You agree not to export or re-export the Software to any country in violation of the export control laws of the United States of America or the

export control laws of any other applicable country

medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive or

other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic or printed copy of this manual must

contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content without

obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site (www.garmin.com) for current updates and supplemental

information concerning the use and operation of this and other Garmin products.

Garmin

®

and GPSMAP

®

are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GWS

™

and GMI

™

are trademarks of Garmin Ltd. or

its subsidiaries. These trademarks may not be used without the express permission of Garmin. NMEA 2000

®