Rockler 69982 Operating instructions

Brand: Rockler

Model: 69982

Type: Operating instructions

Rockler 69982 Wall-Mount HEPA Cyclone Dust Collector is a powerful tool that helps keep your workshop clean and free of dust and debris. With its advanced cyclonic technology and HEPA filter, it effectively captures even the finest dust particles, providing a healthier and safer working environment. The remote control allows for convenient operation, while the large-capacity canister and easy-to-empty dust bag make maintenance a breeze. Whether you're a professional woodworker or a DIY enthusiast, this dust collector is an essential addition to your workshop.

Review full instructions prior to use for important safety information.

Always check Rockler.com to confirm that you are using the most recent version of instructions for your product.

Wall-Mount HEPA Cyclone Dust Collector Instructions

Effective February 2023

GENERAL SAFETY WARNINGS

This product is designed only for specific applications as defined in the instructions and should not be modified or used for any

manner not described in these instructions. Use only recommended accessories. Before using the Wall-Mount HEPA Cyclone Dust

Collector: READ, UNDERSTAND and FOLLOW ALL INSTRUCTIONS AND SAFETY WARNINGS. KEEP THESE INSTRUCTIONS

READILY AVAILABLE FOR FUTURE REFERENCE.

> Always confirm that you are using the most recent version of

the instructions and safety warnings for your product (see the

instructions link on the product page at Rockler.com).

> Before using another tool with this product, always read,

understand and follow the instructions and safety warnings

in the owner’s manual for that tool. If you do not have the

owner’s manual, obtain one from the tool’s manufacturer

before using it with this product.

> Before using any chemical with this product, always read,

understand and follow all safety warnings and guidelines in

the manufacturer’s Safety Data Sheet (SDS; formerly called

“MSDS”), especially regarding:

• How to safely use the chemical, including potential hazards

and recommended first aid measures;

• Personal safety equipment required to safely use the

chemical (e.g. gloves, eye protection, mask/respirator, etc.);

• Proper and safe handling, storage and disposal of

the chemical.

> Before using this product, review and verify that all tools to be

used with it have safety equipment installed and are in proper

working order as defined by the tool’s owner’s manual.

> Do not use this product until you have read and are

confident you understand:

• Product Specific Safety Warnings (pp. 3-4);

• Electrical Connections and Grounding (p. 5);

• Choosing a Mounting Location (p. 5);

• Prepping the Mounting Location (pp. 6-7);

• Assembly and Installation (pp. 8-13);

• Operating the Dust Collector (p. 14);

• Clearing and Resetting the Remote (pp. 14-15);

• Overload Reset (p. 15);

• Maintenance (p. 15).

> The user assumes all risk and responsibility for the proper and

safe use of this product and for ensuring product suitability for

the intended application.

> It is the sole responsibility of the purchaser of this product

to ensure that anyone you allow to use this product reads

and complies with all instructions and safety precautions

outlined in this manual prior to use.

> Follow all standard shop safety practices, including:

• Keep children and bystanders away from the tool

operating area;

• Do NOT use power tools in explosive environments, or in

the presence of flammable liquids, fumes or dust;

• TURN OFF AND UNPLUG all power tools BEFORE

making any adjustments or changing accessories;

• Remain alert and use good judgment. Do not use this

product if you are in any way impaired by medications,

alcohol, drugs or fatigue;

• Keep your work area well lit and clean;

• Dress appropriately. Secure loose clothing, remove all

jewelry and tie up long hair before using this product;

• ALWAYS wear safety glasses, hearing protection

and respiratory protection that complies with

NIOSH/OSHA/ANSI safety standards;

• Use dust collection tools and dust face masks to

reduce exposure to dust;

• Use safety equipment such as featherboards, push

sticks and push blocks, etc., when appropriate;

• Maintain proper footing at all times and do not overreach;

• Do NOT force woodworking tools.

> These warnings and instructions do NOT represent the total

of all information available regarding tool safety, use and

technique. Always seek out opportunities to learn more

and improve your skills and knowledge.

Drilling, sawing, sanding or machining wood

products can expose you to wood dust, a substance known

to the State of California to cause cancer. Avoid inhaling

wood dust or use a dust mask or other safeguards for

personal protection. For more information go to

www.P65Warnings.ca.gov/wood.

Danger indicates a hazardous situation that, if not avoided, will result in death or serious injury.

Warning indicates a hazardous situation that, if not avoided, could result in death or serious injury.

Caution indicates a hazardous situation that, if not avoided, may result in minor or moderate injury

or property damage.

Notice indicates important or helpful information and/or user tips.

BP0622

PRODUCT SPECIFIC SAFETY WARNINGS

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)

Failure to understand and follow all safety warnings and instructions

could result in fire, electrical shock or serious injury.

Electrical/Grounding

> Connect to a properly grounded outlet only. See

Grounding Instructions (p. 5).

> Improper connection of the equipment-grounding

conductor can result in a risk of electrical shock. Check

with a qualified electrician or service person if you are in

doubt as to whether the outlet is properly grounded. Do

NOT modify the plug provided with the appliance – if it

will not fit the outlet, have a proper outlet installed by

a qualified electrician.

> FOLLOW all electrical and safety codes, including the

National Electric Code (NEC) and the Occupational

Safety and Health Administration regulations (OSHA).

All electrical connections and wiring should be made by

qualified personnel only.

> Do NOT use outdoors or on wet surfaces.

> Do NOT use with damaged cord or plug. Do NOT use if

dust collector is not working as it should, has been dropped,

damaged, left outdoors, or dropped into water.

> Make sure the Main Power Switch is in the OFF position

before connecting the machine to the power source.

> Do NOT pull on or carry by cord, use cord as a handle,

close a door on cord, or pull cord around sharp edges or

corners. Do NOT run anything over cord. Keep cord

away from heated surfaces.

> Do NOT unplug by pulling on cord. To unplug, grasp the

plug, not the cord.

> Do NOT handle plug or appliance with wet hands.

> If connected to a circuit protected by fuses, use time-delay

fuses, marked Type D, with this dust collector.

> The use of extension cords is discouraged; try to position

the machine near the power source. If an extension cord

is necessary, use only three-wire extension cords that have

three-prong grounding plugs and three-pole receptacles that

accept the tool’s plug.

> Extension cords in poor condition or that are too small can

pose fire and shock hazards. When using an extension

cord, be sure it is in good condition and properly rated.

Product Specific Safety Warnings continued on page 4

Safe Use

> Do NOT use to pick up liquids, flammable or combustible

liquids or materials, such as gasoline, or use in areas where

they may be present. Do NOT use to pick up anything that

is burning or smoking, or toxic materials. Do NOT use to

pick up metal items/shavings. Items not to be picked

up with this machine include (but are not necessarily

limited to):

• Fuels • Lighter fluid • Cleaners

• Oil-based paints • Natural gas • Hydrogen

• Coal dust • Magnesium dust • Grain dust

• Gunpowder • Cigarettes • Matches

• Hot ashes

> Do NOT leave appliance when plugged in. Unplug from

outlet when not in use and before servicing.

> NEVER leave tool running and unattended.

> Turn off all controls before unplugging.

> Do NOT put any object into openings. Do NOT use with

any opening blocked by debris; keep free of dust, lint, hair,

and anything that may reduce airflow.

> Remove all jewelry, secure loose clothing, and tie up long

hair before using this machine. To avoid serious injury, keep

hair, loose clothing, fingers, and all parts of body away from

openings and moving parts.

> NEVER operate without hose connected to suction

chute (inlet). Hazardous moving parts inside. Unplug

before removing hose from suction chute; attach hose

on the suction chute before plugging in.

> Do NOT operate without capping unused dust ports.

> Do NOT use without dust bag mounted in place on Canister

Filter and dust bag and inner frame installed in Drum. Do

NOT use without Drum Lid lowered onto Drum. Make sure

to reinstall inner frame in Drum after emptying Drum Plastic

Bag. Do NOT discard the frame while emptying the bag.

> Wear approved safety glasses, dust mask or respirator

and hearing protection while using this machine or

emptying the dust bag

> For household use only.

PRODUCT SPECIFIC SAFETY WARNINGS CONTINUED

Safe Use (continued from p. 3)

> Close attention is necessary when used by or near children.

> Use only as described in this manual. Use only

manufacturer’s recommended attachments.

> Do NOT hang from the machine or allow anyone

else to do so.

> For the unit to operate, the safety key must be inserted

in the Main Power Switch. It can be removed to

prevent unauthorized use.

Installation/Assembly

> Do NOT install the Wall Mount HEPA Cyclone Dust

Collector outside the work area, especially if the work

area contains a gas-fueled appliance. In drawing the air

outside, the dust collector could lead to a buildup inside

the work area of combustion gases – including deadly

carbon monoxide – that normally are vented from

gas-fueled appliances.

> The Dust Collector must be secured using all four included

5/16" x 3" Washer Head Lag Screws driven into structurally

sound wooden wall studs or into 2 x 4 wooden cleats

securely attached to wooden wall studs. All cleats

spanning wall studs must be long enough that both

ends of the cleats can be bolted to studs.

> Do NOT use wall anchors or drywall anchors to mount

the Dust Collector.

> To prevent damage to the power cord, select a

mounting location for the Dust Collector that will

keep the cord out of high-traffic areas.

> The motor assembly of the Dust Collector is very heavy.

To avoid the risk of serious injury, you MUST obtain the

help of another adult to lift the unit into position. Use

proper lifting techniques.

> After assembly or maintenance, make sure that you

have removed all loose tools from the machine

before turning it on.

Maintenance

> To avoid injury from accidental starting, turn the unit off

and unplug power cord before changing or cleaning

dust bag or before any other servicing.

> Periodically inspect dust and filter bags for any cuts,

rips or tears. Do NOT operate the dust collector with

damaged parts, bags, or hoses.

> Check and empty dust bags regularly. Do NOT allow bags

to become more than half-full.

SAVE THESE INSTRUCTIONS

> Do NOT install the Wall Mount HEPA Cyclone Dust

Collector outside the work area, especially if the work

area contains a gas-fueled appliance. In drawing the air

outside, the dust collector could lead to a buildup inside

the work area of combustion gases – including deadly

carbon monoxide – that normally are vented from

gas-fueled appliances.

> The Dust Collector must be secured using all four

included 5/16" x 3" Washer Head Lag Screws driven

into structurally sound wooden wall studs or into 2 x 4

wooden cleats securely attached to wooden wall studs.

All cleats spanning wall studs must be long enough that

both ends of the cleats can be bolted to studs.

> Do NOT use wall anchors or drywall anchors to

mount the Dust Collector.

> To prevent damage to the power cord, select a

mounting location for the Dust Collector that will

keep the cord out of high-traffic areas.

> After assembly or maintenance, make sure that you

have removed all loose tools from the machine before

turning it on.

Electrical Connections and Grounding

Grounding Instructions

This dust collector must be grounded. If it should malfunction

or break down, grounding provides a path of least resistance

for electric current to reduce the risk of electric shock. This

appliance is equipped with a cord having an equipment-grounding

conductor and grounding plug. The plug must be inserted into

an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

This dust collector is for use on a nominal 120V circuit and has

a grounding attachment plug that looks like the plug illustrated

in Fig 1. Make sure that the appliance is connected to an outlet

having the same configuration as the plug. No adapter should be

used with this dust collector.

Choosing a Mounting Location

> Do NOT use outdoors or on wet surfaces.

> Do NOT use with damaged cord or plug. If appliance

is not working as it should, has been dropped, damaged,

left outdoors, or dropped into water, return it to a

service center.

> Do NOT pull or carry by cord, use cord as a handle,

close a door on cord, or pull cord around sharp edges

or corners. Do NOT run appliance over cord. Keep

cord away from heated surfaces.

> Do NOT unplug by pulling on cord. To unplug, grasp

the plug, not the cord.

> Do NOT handle plug or appliance with wet hands.

> If connected to a circuit protected by fuses, use

time-delay fuses, marked Type D, with this appliance.

> Make sure the Main Power Switch is in the OFF position

before connecting the machine to the power source.

> The use of extension cords is discouraged; try to position

the machine near the power source. If an extension cord

is necessary, use only three-wire extension cords that

have three-prong grounding plugs and three-pole

receptacles that accept the tool’s plug.

> Extension cords in poor condition or that are too small

can pose fire and shock hazards. When using an

extension cord, be sure it is in good condition

and properly rated.

When attached to the Main Housing of the Wall Mount HEPA

Cyclone Dust Collector the mounting brackets’ holes are spaced

horizontally 16” on center to correspond to the common spacing

for wall studs. If your desired mounting location on an open-stud

wall does not line up with studs spaced 16” on center, or if you are

mounting to a finished wall, you MUST first bolt two horizontal

2 x 4 wooden cleats to wooden wall studs and then mount the

Dust Collector to the cleats. The cleats must be spaced vertically

63⁄4” apart (from the top of one cleat to the top of the other) to

accommodate the spacing on the Dust Collector’s mounting

brackets. Additionally, the cleats must be long enough that both

ends can be bolted to a wooden wall stud.

Improper connection of the

equipment-grounding conductor can result in a risk

of electrical shock. Check with a qualified electrician or

service person if you are in doubt as to whether the outlet

is properly grounded. Do NOT modify the plug provided

with the appliance – if it will not fit the outlet, have a

proper outlet installed by a qualified electrician.

Fig. 1

Grounding Plug

Cover of

grounded

outlet box

Prepping the Mounting Location

To locate and mark wooden wall studs in a finished wall, use a

stud finder. As you locate the studs in your desired mounting

area, be sure to mark both edges and the centerline of each stud.

Fig. 2. Be aware that stud spacing can vary. Take your time

identifying and marking the studs to be sure you are certain of

their locations. If you have any doubts that you have located the

studs properly, seek professional installation assistance.

The top set of Lag Screws must be located

523⁄4" from the floor to enable a tight connection to the Drum.

Open Studs Spaced 16" On Center

1. Determine the mounting location. Use a level to mark a

horizontal line on both studs at a height of 523⁄4" from the

floor for the top set of the Dust Collector’s mounting holes.

2. Measure down 63⁄4" and use the level to mark a horizontal

line on both studs; this will help you place the pilot hole

locations for the bottom set of the unit’s mounting holes.

Fig. 3.

3. Use a level or other straightedge to make vertical marks

across the horizontal marks at the center of each stud.

Measure to double-check that the intersections of these

marks are 16" apart. Fig. 3.

4. Drill 3/16" diameter pilot holes 21⁄2" deep at the four

cross marks. Fig. 3.

5. Using the included 11mm Open Wrench, drive a 5/16" x 3"

Washer Head Lag Screw at each location, stopping when the

heads of the Lag Screws are about 1" out from the surface.

6. Install Vibration Dampeners on the left and right sets of

5/16" x 3" Washer Head Lag Screws. Note that the Vibration

Dampeners are side-specific; the slot part of the keyhole

> The Wall Mount HEPA Cyclone Dust Collector must

be secured using all four included 5/16" x 3" Washer

Head Lag Screws driven into structurally sound

wooden wall studs.

Fig. 4Fig. 3

Fig. 2

Centerline

Outer Edge

of Stud

Outer Edge

of Stud

63⁄4"

16"

5/16" x 3" Washer

Head Lag Screw

Right Vibration

Dampener

Left Vibration

Dampener

3/16" diameter pilot

holes 21⁄2" deep

opening should be at the top. Also make sure enough of

the Lag Screws extend from the studs that the keyhole

slots on the unit’s Right and Left Brackets will be able

to fit onto them easily. Fig. 4.

Using Cleats

1. Determine the mounting location. If mounting to a finished

wall, you should have marked the edges and centerlines

of the studs at the desired location in Choosing a Mounting

Location. If you have not done so, review the section and

mark all stud locations now; be sure to identify at least one

stud beyond the intended footprint of the Dust Collector

on each side so that both ends of the cleats will be

bolted to a stud.

2. Measure the distance between the outside edges of the

two outside studs located in Step 1 and cut two 2 x 4

cleats to that length.

3. Transfer the stud locations (including centerlines) from the

wall onto the cleats to determine the location of all pilot holes

and counterbores needed to accept 5/16" x 4" Lag Screws

and Washers (not included). Lag screws must be installed

at every stud the cleats cross and at both ends of the cleats.

Fig. 5.

4. At the center of each stud location on the cleats, use a

1" Forstner bit to drill counterbores of sufficient depth to

accommodate a Washer and the head of the Lag Screw.

5. Drill a 5/16" through hole centered in each counterbore.

6. Hold the upper cleat to the wall at the desired mounting

location – keeping in mind that the top set of Lag Screws

must be located 523⁄4" from the floor to enable a tight

connection to the Drum -- and align the pilot holes with

the stud centerlines. Check that it’s level; then use

the pilot holes in the cleat to mark the drilling locations.

Make sure the marks are centered on the studs. Fig. 5.

7. Drill 3/16" diameter holes through the drywall (if applicable)

and into the studs at the spots you just marked.

8. Use 5/16" x 4" Lag Screws and Washers (not included)

to securely mount the cleat to the studs.

9. Repeat Steps 7-8 to install the lower cleat, taking care to

maintain the 63⁄4" vertical spacing from the top of the upper

cleat to the top of the lower cleat. Fig. 5.

10. On the upper cleat, mark a level horizontal line and then

measure and make vertical marks at the locations for the

top set of mounting screws. Make sure that the marks

are 16" apart. Fig. 5.

11. Use a level to transfer the vertical marks to the lower cleat

and then measure down from the top marks 63⁄4" to make the

cross marks locating the bottom set of mounting screws.

Fig. 5.

12. Drill 3/16" diameter pilot holes at these locations.

13. Using the included 11mm Open Wrench, drive a 5/16" x 3"

Washer Head Lag Screw at each location, stopping to leave

the heads of the Screws about 1" out from the surface.

14. Install Vibration Dampeners on the left and right sets

of 5/16" x 3" Washer Head Lag Screws. Note that the

Vibration Dampeners are side-specific; the slot part of the

keyhole opening should be at the top. Also make sure

enough of the Lag Screws extend from the studs that the

keyhole slots on the unit’s Right and Left Brackets will be

able to fit onto them easily. Fig. 6.

Fig. 5 Fig. 6

63⁄4”

16"

3/16" diameter holes

5/16" x 3" Washer

Head Lag Screw

Right Vibration

Dampener

Left Vibration

Dampener

Stud Locations

Fig. 9 Fig. 10

Fig. 7 Fig. 8

Main Housing

(Mounted

to Wall)

Right Bracket

Left Bracket

Main Housing

5/16"-18 x 1/2" Flange Bolt

Cone Clamp

Cone

1mm x 30mm x

38" Foam Tape

Hose Clamp

Hose

Assembly and Installation

1. Using the 12mm end of the 10~12mm Open Wrench, attach

the Right Bracket and Left Bracket securely to the Main

Housing with four 5/16"-18 x 1/2" Flange Bolts. Fig. 7.

2. With the help of another adult, lift the Main Housing onto

the four 5/16" x 3" Washer Head Lag Screws, fitting the

keyhole openings in the Right Bracket and Left Bracket

over the heads of the Screws. Allow the unit to lower

slightly so the Screws seat in the keyhole slots. Fully

tighten the Screws, using the included 11mm Open

Wrench. Fig. 8.

3. Turn the Cone upside down and apply one of the pieces

of 1mm x 30mm x 38" Foam Tape in the channel around the

narrow opening of the Cone. Trim any excess tape. Fig. 9.

4. Fit one of the Hose Clamps onto the Hose. Then work the

Hose onto the Cone and secure it with the Hose Clamp.

Make sure the Hose Clamp is lined up with the

1mm x 30mm x 38" Foam Tape. Fig. 9.

Fig. 11

Fig. 12

The motor assembly of the Wall Mount

HEPA Cyclone Dust Collector is very heavy. To avoid

the risk of serious injury, you MUST obtain the help of

another adult to lift the unit into position. Use proper

lifting techniques.

The following step will be easier to

complete if you obtain the assistance of another adult.

5. Position the Cone beneath the Main Housing so that the

top flange of the Cone is flush with the bottom flange of the

Main Housing. Use the 10mm end of the 10~12mm Open

Wrench to loosen the bolt on the Cone Clamp, and then

fit the clamp over both flanges, holding them together.

Fig. 10.

6. Make sure that the tabs on the sides of the Cone are parallel

to the wall to which the dust collector is mounted and then

tighten the bolt on the Cone Clamp to secure the Cone to

the Main Housing. Fig. 10.

7. Apply the 1mm x 30mm x 191⁄4" Inlet Foam Tape around the

inlet port near the edge. The tape should completely encircle

the port. Use the hole in the inlet as a guide to poke a hole in

the tape where the 3/16" x 3/8" Phillips Panhead Screw used

to secure the Inlet Y-Adapter will go. Fig. 11.

8. Fit the Inlet Y-Adapter onto the inlet, over the applied Inlet

Foam Tape and secure it with the #10-24 x 3/8" Phillips

Panhead Screw. Fig. 11.

9. Fit the Handle onto the post projecting from the top of the

Canister Filter, lining up the hole for the 5/16"-18 x 3/4" Set

Screw with the flat area on the post. Thread the Set Screw

into the Handle and thread the 5/16"-18 Hex Nut loosely

onto the Set Screw. Use the included 4mm Hex Wrench

to tighten the Set Screw; then use the 12mm end of the

10~12mm Open Wrench to tighten the Hex Nut. (The

Handle is used to spin a three-paddle mechanism inside

the canister that dislodges built-up dust from the

pleated filter.) Fig. 12.

10. Apply the 3mm x 20mm x 493⁄4" Foam Tape in the channel

around the bottom of the Canister Filter, just above the lip.

Trim any excess. Fig. 12.

3mm x 20mm x 493⁄4"

Foam Tape

Canister

Filter

Handle

#10-24 x 3/8"

Phillips Panhead

Screw

Main Housing

(Mounted to Wall)

1mm x 30mm x 191⁄4"

Inlet Foam Tape

Cap

Inlet Y-Adapter

5/16"-18 x 3/4" Set Screw

5/16"-18 Hex Nut

Fig. 13

Six 5/16"-18

Flange Nuts

Six 5/16"-18 x 3/4"

Flange Bolts

Canister Filter

Gasket

Main Housing

(Mounted to wall)

Canister Filter

Plastic Bag

Bag Clamp

11. Lift the Canister Filter up to the Main Housing. Position

the Gasket between the flanges of the Canister Filter

and Main Housing, taking care to align the holes for the

mounting bolts. Securely mount the Canister Filter to the

Main Housing with six 5/16"-18 x 3/4" Flange Bolts and

six 5/16"-18 Flange Nuts, using the 12mm end of the

10~12mm Open Wrench to tighten. Fig. 13.

12. Fit the Canister Filter Plastic Bag over the bottom of the

Canister Filter, making sure that the edge extends at least

to the top of the 3mm x 20mm x 493⁄4" Foam Tape. You can

use painter’s tape to hold the bag in position if it tends to slip

off during installation. Install the Bag Clamp and secure

tightly around the bag. Fig. 13.

13. Thread the Drum Casters into the mounting sockets on the

underside of the Drum and tighten. Fig. 14.

14. Securely attach the Drum Handles to the Drum, using two

1/4"-20 x 1/2" Flathead Screws for each handle. Fig. 14.

15. Assemble the inner frame that will fit inside the Drum Plastic

Bag in the Drum to keep the Plastic Bag from collapsing

when the Dust Collector is activated: Use M3 x 12mm

Phillips Head Screws and M3 Hex Nuts to attach the three

Long Inner Frame Supports to the two Inner Frame Hoops.

Space the Supports 120° apart (every other set of holes in

the Hoops) and make sure that the feet of the Supports

face inward. Fig. 15.

16. Use the remaining M3 x 12mm Phillips Head Screws and

M3 Hex Nuts to attach the three Short Inner Frame Supports

to the two Inner Frame Hoops at the remaining sets of

mounting holes. Fig. 15.

17. Place the Drum Plastic Bag in the Drum, with the top of the

bag folded over the top of the Drum. Place the assembled

inner frame in the bag and carefully press it all the way

down. Fig. 15.

The following step will be easier to

complete if you obtain the assistance of another adult.

Fig. 14

Fig. 15

Drum

Plastic

Bag

Drum

Casters

1/4"-20 x 1/2"

Flathead Screws

Drum

Handles

Drum

Long Inner

Frame Support

M3 x 12mm

Phillips Head Screw

Inner

Frame

Hoop

Short

Inner

Frame

Support

Hex

Nut

Fig. 16

Drum

1mm x 30mm x 38" Foam Tape

Drum Lid

Hose Clamp

18. Apply the remaining piece of 1mm x 30mm x 38" Foam

Tape around the flange of the Drum Lid. Trim any excess.

Fig. 16.

19. Place the Drum Lid on the Drum and roll the Drum directly

under the Hose. Fit the remaining Hose Clamp on the bottom

of the Hose and work the Hose onto the flange of the Drum

Lid. Work the Hose Clamp down so that it’s around the

flange of the Drum Lid and tighten it in place. Fig. 16.

20. Lift the Quick Lever up to the Cone, fitting the threaded posts

of the Quick Lever into the holes in the tops of the brackets

on the Drum Lid. Align the plates on the Quick Lever with

the plates on the Cone and secure them with four M5 x 8mm

Phillips Head Screws at each plate location. Fig. 17.

21. The Quick Lever should be in the fully down position, with

the hex nuts on the threaded posts tight against the tops of

the brackets in the Drum Lid. If that’s not the case, use the

14mm end of the 10~14mm Open Wrench to adjust the hex

nuts until the Quick Lever is fully down and the hex nuts

are tight against the tops of the brackets in the Drum Lid.

This is important so that the Quick Lever can be raised

to allow emptying of the Drum. Fig. 17.

22. Thread an M10 Locknut onto each threaded post of the

Quick Lever and tighten securely. Test the Quick Lever to

make sure that the Drum Lid lifts clear of the Drum when

it is raised and does not put upward pressure on the main

housing when it is lowered. Make any adjustments needed.

Fig. 17.

23. Connect 4" dust hose to one or both of the ports on the

Inlet Y-Adapter, securing them with hose clamps (not

included). A cap is included in case only one port is used.

For efficient dust collection when hoses are connected

to both ports, blast gates should be used.

Fig. 17

M10 Locknut

Quick Lever

M5 x 8mm Phillips Head Screws

> Do NOT use to pick up flammable or combustible

liquids, such as gasoline, or use in areas where

they may be present.

> Do NOT use to pick up liquids, flammable or combustible

materials, anything that is burning or smoking, or toxic

materials. NEVER use near combustible materials.

Do NOT use to pick up metal items/shavings

due to risk of spark.

> Do NOT leave appliance when plugged in. Unplug from

outlet when not in use and before servicing.

> NEVER leave tool running and unattended.

> Turn off all controls before unplugging.

> Do NOT put any object into openings. Do NOT use with

any opening blocked by debris; keep free of dust, lint, hair,

and anything that may reduce airflow.

> Remove all jewelry, secure loose clothing, and tie up long

hair before using this machine. To avoid serious injury, keep

hair, loose clothing, fingers, and all parts of body away from

openings and moving parts.

> NEVER operate without hose connected to suction

chute (inlet). Hazardous moving parts inside. Unplug

before removing hose from suction chute; attach hose

on the suction chute before plugging in.

> Do NOT operate without capping unused dust ports.

> Do NOT use without dust bag mounted in place on Canister

Filter and dust bag and inner frame installed in Drum. Do

NOT use without Drum Lid lowered onto Drum. Make sure

to reinstall inner frame in Drum after emptying Drum Plastic

Bag. Do not discard the frame while emptying the bag.

> Wear approved safety glasses, dust mask or respirator

and hearing protection while using this machine or

emptying the dust bag

> For household use only.

> Close attention is necessary when used by or near children.

> Use only as described in this manual. Use only

manufacturer’s recommended attachments.

> Do NOT hang from the machine or allow anyone

else to do so.

> For the unit to operate, the safety key must be inserted

in the Main Power Switch. It can be removed to

prevent unauthorized use.

Operating the Dust Collector

Turning on the Dust Right Wall-Mount HEPA Cyclone Dust

Collector is a two-step process that can be accomplished at the

machine or with the Remote Control.

The radio-frequency Remote Control operates on one 9-Volt

battery (not included) and has an effective range of up to

about 25 feet.

1. Lift the paddle of the Main Power Switch.

2. Press the On/Off Switch on the power panel OR

the ON button on the Remote Control. Make sure the 9-Volt

Battery is installed. The motor must be completely stopped

before it can be turned back on with the Remote.

Clearing and Resetting the Remote

If the Remote Control fails to function, try installing a new battery.

If it still will not work, you must clear and reset the remote.

1. Press the Remote Reset button on the unit’s power panel

for three seconds, until the receiver “beeps” three times.

2. Press the Remote Reset button on the unit’s power panel

for one second, until the receiver “beeps” once.

3. Press the ON button on the handheld Remote Control

until the light on the receiver “beeps” twice.

Dust Collector Power Panel

Remote

Reset

On/Off

Switch

Main

Power

Switch

Circuit

Breaker

Reset

Yellow

Safety

Key

Changes or modifications to this unit not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Check Rockler.com for updates. If you have further questions, please

contact our Technical Support Department at 1-800-260-9663

or support@rockler.com

IDENTIFICATION OF ASSEMBLED PRODUCT

WALL-MOUNT HEPA CYCLONE DUST COLLECTOR

INSTRUCTIONS (69982/UB1500Z) WITH REMOTE

CONTROL (IC-315Z)

IDENTIFICATION OF MODULAR COMPONENTS USED

REMOTE CONTROL FCC ID ANZ-IC-315Z

APPLICABLE COMPLIANCE STATEMENTS

NOTE:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV

technician for help

RESPONSIBLE PARTY / MANUFACTURER

ROCKLER COMPANIES

ADDRESS 4365 WILLOW DRIVE, MEDINA, MN 55340

TELEPHONE 1-800-279-4441

WWW.ROCKLER.COM

Frequency Range: 315 MHz

Modulation Type: Amplitude-shift keying (ASK)

Bandwidth: 189.58 KHz

Number of Channels: 1 channel

Power Operation: DC 9V Battery

4. Press the Remote Reset button on the unit’s power panel

for three seconds, until the receiver “beeps” three times.

The Remote Control is now reset.

Overload Reset

The Dust Right Wall-Mount HEPA Cyclone Dust Collector

incorporates overload protection to help prevent damage to the

motor. If the motor is drawing excessive current during periods of

extended operation and begins to overheat, a relay in the control

panel will break the circuit and shut off the dust collector.

If the overload protection is tripped:

1. Flip the Main Power Switch to the OFF position and

unplug the machine.

2. Allow the motor to cool.

3. Press the Circuit Breaker Reset button.

4. Plug in the cord and turn on the unit.

Maintenance

1. Periodically inspect the Canister Filter Plastic Bag and

Drum Plastic Bag for any cuts, rips or tears. Do NOT

operate the dust collector with a damaged bag or hose.

2. Empty the Canister Filter Plastic Bag and Drum Plastic Bag

regularly. Do NOT allow the Canister Filter Plastic Bag to

become more than half-full. Empty the Drum Plastic Bag

once contents reach the full line on the window. Make sure

to reinstall inner frame in Drum after emptying Drum Plastic

Bag. Do not discard the frame while emptying the bag.

3. All bearings are shielded and permanently lubricated. No

other lubrication of this machine is necessary.

4. When the machine is not being used, unplug the power

cord from the outlet and store the cord away from any

potential sources of damage, including high-traffic areas,

sharp objects, sources of heat, harsh chemicals

and moisture.

69982

Rev 0223

Distributed by Rockler Companies, Inc.

4365 Willow Dr. Medina, MN 55340

1-800-279-4441

www.rockler.com

Rockler 69982 Operating instructions

Rockler 69982 Operating instructions

Rockler 69982 Operating instructions

Other documents