SUSSEX VMDSRH User manual

SUSSEX
Brand
SUSSEX
Model
VMDSRH
Type
User manual

Sure, here is a brief product information for SUSSEX VMDSRH:

The SUSSEX VMDSRH is a mixer diverter system that allows you to control the flow of water to two different outlets, such as a showerhead and a bathtub faucet. It features a durable construction with a 5.0 WELS water rating, ensuring both efficiency and performance. Installation requires a licensed plumber and involves preparing a noggin, mounting the Masterfit, and connecting the hot and cold water lines. Once installed, you can easily switch between outlets using the diverter handle.

Sure, here is a brief product information for SUSSEX VMDSRH:

The SUSSEX VMDSRH is a mixer diverter system that allows you to control the flow of water to two different outlets, such as a showerhead and a bathtub faucet. It features a durable construction with a 5.0 WELS water rating, ensuring both efficiency and performance. Installation requires a licensed plumber and involves preparing a noggin, mounting the Masterfit, and connecting the hot and cold water lines. Once installed, you can easily switch between outlets using the diverter handle.

2
SUSSEX
INFO & INSTALL GUIDES
CONCEPTS
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
INFORMATION SHEET
Calibre Basin Mixer
Product code: CBM
160
80
100
40
35
48
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
Calibre Basin Mixer
Product code: Available options:
CBM Basin Mixer
CEBM Extended Basin Mixer
INSTALLATION GUIDE
PLUMBER NOTE
-On-site testing using higher water pressures must be
conducted with the Mixer in the closed position.
(STATIC TEST )
-Under no circumstances is the Mixer to be opened
when exceeding the maximum stated water pressure.
-At the completion of testing, do not relieve any high
water pressure by operating the Mixer.
-Exposing the internals of the Mixer Cartridge to higher
than specified water pressures will void the
manufacturers warranty.
INSTALLATION GUIDELINES
-The Mixer is supplied assembled, only the Fixing nut
and the Clamp need to be removed.
-After removing the mentioned parts, lower the Mixer
on to the mounting surface and fit the Flexible Hoses.
-In some cases the Flexible Hoses may need to be fed
through from under the mounting surface and then
attached. (Tighten using appropriate spanner)
-After securing the Flexible Hoses, fit Clamp and attach
the Fixing Nut from underneath.
-Before fully securing the Mixer ensure that the Base O
Ring is intact and the Mixer is properly centered over
the mounting surface hole.
-The Mixer mounting surface must be completely sealed
and water-tight.
-The 1/2” Fittings of the Flexible Hoses have a conical
seal, ensure that the matching threads are cut square
and burr free.
-Prior to connecting the Flexible Hoses, ensure all
pipework is thoroughly flushed and ensure pipework is
free of any dirt or debri.
-Isolating Stop Valves are recommended with all
installations. (not supplied)
-Connect the Flexible Hoses to Hot and Cold pipework
fittings, ensure the Hoses do not kink or become
twisted when tightening.
-Check all fittings and connections are secure and
water-tight.
BASE
O-RING
CLAMP
Hole Size
32-35mm
50mm Max.
Bench thickness
1/2" BSP Fittings
with conical Seals FLEXIBLE HOSES
FIXING
NUT
CONCEPT One
1
NOGGING
80 mm
B/Plate
Apply Silicone
64mm
Dress
Ring
t
Apply Silicone
Stud Face
Finished
Wall Surface
Handle
Pin
Set
Screw
Handle
Body
2
NOGGING
Stud Face
Finished
Wall Surface
Backplate
Set
Screw
Handle
Pin
Handle
Body
64mm
Dress
Ring
Product code
Voda
VMDSRH Mixer diverter system
Mixer diverter system Dress kit
Diverter dress kit
Mixer dress kit
- Remove Mixer protective cover.
- Using silicone, seal the wall surface around the Mixer and Outlet threads.
- Apply a small amount of silicone to the rear of the backplate prior to mounting onto the wall.
- After Backplate has been mounted, fit the Mixer Dress Ring.
- Fit the handle body onto the Mixer Cartridge Lever ensuring the Handle is fully engaged.
- Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well).
- Attach the Handle Pin.
Note: Apply a small amount of silicone or mild adhesive (Loctite) to the thread of the Handle Pin to assist in
preventing the Pin from becoming loose).
- Remove Diverter protective cover.
- Fit Dress Ring.
- Fit the Handle Body.
Note: The Pin position of the Handle is optional. Select as desired (total movement is 90 degrees).
- Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well).
- Attach the Handle Pin.
Note: Apply a small amount of silicone or mild adhesive (Loctite) to the thread of the Handle Pin to assist in
preventing the Pin from becoming loose).
To complete the installation, operate the Mixer(s) checking the flow of both hot and cold water from Outlet.
Check all fittings and fixtures for water leaks.
sussextaps.com.au
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.
2
SUSSEX
INFO & INSTALL GUIDES
CONCEPTS
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
INFORMATION SHEET
Calibre Basin Mixer
Product code: CBM
160
80
100
40
35
48
sussextaps.com.au
5.0 litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
AS/NZS 3718:2005
LIC. 20081
Calibre
Calibre Basin Mixer
Product code: Available options:
CBM Basin Mixer
CEBM Extended Basin Mixer
INSTALLATION GUIDE
PLUMBER NOTE
-On-site testing using higher water pressures must be
conducted with the Mixer in the closed position.
(STATIC TEST )
-Under no circumstances is the Mixer to be opened
when exceeding the maximum stated water pressure.
-At the completion of testing, do not relieve any high
water pressure by operating the Mixer.
-Exposing the internals of the Mixer Cartridge to higher
than specified water pressures will void the
manufacturers warranty.
INSTALLATION GUIDELINES
-The Mixer is supplied assembled, only the Fixing nut
and the Clamp need to be removed.
-After removing the mentioned parts, lower the Mixer
on to the mounting surface and fit the Flexible Hoses.
-In some cases the Flexible Hoses may need to be fed
through from under the mounting surface and then
attached. (Tighten using appropriate spanner)
-After securing the Flexible Hoses, fit Clamp and attach
the Fixing Nut from underneath.
-Before fully securing the Mixer ensure that the Base O
Ring is intact and the Mixer is properly centered over
the mounting surface hole.
-The Mixer mounting surface must be completely sealed
and water-tight.
-The 1/2” Fittings of the Flexible Hoses have a conical
seal, ensure that the matching threads are cut square
and burr free.
-Prior to connecting the Flexible Hoses, ensure all
pipework is thoroughly flushed and ensure pipework is
free of any dirt or debri.
-Isolating Stop Valves are recommended with all
installations. (not supplied)
-Connect the Flexible Hoses to Hot and Cold pipework
fittings, ensure the Hoses do not kink or become
twisted when tightening.
-Check all fittings and connections are secure and
water-tight.
BASE
O-RING
CLAMP
Hole Size
32-35mm
50mm Max.
Bench thickness
1/2" BSP Fittings
with conical Seals FLEXIBLE HOSES
FIXING
NUT
CONCEPT One
1
Cold
Hot
Mixer
Outlet 1
Outlet 2
NOGGING
Dress Ring
30-3 mm
Wall Covering
Max. 30mm
90
Stud face
Pipe Connections
Maste t
Outlet
1
Mixer
Min.
8mm
This
Side
UP
Diverter
70
Diverter
Vi ew f ro m ab ov e
2
Back Plate
Handle
Body
Note: The diverter is of the dial type, rotate handle
to direct the water flow to the chosen Outlet.
Product code
Voda
VMDSRH Mixer diverter system
Mixer diverter system Rough-in
Plumber note
Pipe connections
Rough in plumbing
- Prior to installing, calculate the finished wall thickness, maximum is 30mm thick, contact manufacturer for
further options.
- If Wall thickness is greater than 30mm, contact manufacturer for further options.
- Prepare a Nogging to be fixed parallel between the Wall Studs.
- The Nogging must be fitted to enable the base of the Masterfit to be 30-32mm back from the Stud Face.
- The Masterfit will be marked “This side Up” to indicate orientation.
- Using the screws (x4) provided, mount the Masterfit to the Nogging. Ensure the Masterfit is level and square.
- On-site high pressure line testing must be conducted with the Mixer in the closed position. (STATIC TEST ONLY)
- Under no circumstances is the Mixer to be opened when exceeding the maximum stated water pressure.
- At the completion of the testing, do not relieve any high pressure by opening the Mixer.
- Exposing the internals of the Mixer Cartridge to higher than specified water pressures, will void the
manufacturer’s warranty.
- The Hot and Cold ports are marked on the Masterfit. (Mixers have individual Hot/Cold inlet ports).
- Flush all water feed lines. All lines must be free from any dirt and debris before connecting to the Masterfit.
- Connect Hot and Cold lines to the corresponding 1/2” BSP ports of the Masterfit. (see Drawing)
- Do not remove any factory fitted pressure plugs or Fixings.
- Once all water connections are made, check Hot/Cold water flow by operating the Mixer Cartridge.
- Check all fittings and fixtures for leaks.
- Leave the Mixer(s) in the closed position and replace the Mixer protective cover.
- Store the Dress Kit in a safe place until required (see Dress Finishing Guide)
sussextaps.com.au
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.
  • Page 1 1
  • Page 2 2

SUSSEX VMDSRH User manual

SUSSEX
Brand
SUSSEX
Model
VMDSRH
Type
User manual

Sure, here is a brief product information for SUSSEX VMDSRH:

The SUSSEX VMDSRH is a mixer diverter system that allows you to control the flow of water to two different outlets, such as a showerhead and a bathtub faucet. It features a durable construction with a 5.0 WELS water rating, ensuring both efficiency and performance. Installation requires a licensed plumber and involves preparing a noggin, mounting the Masterfit, and connecting the hot and cold water lines. Once installed, you can easily switch between outlets using the diverter handle.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents