Sanyo LCD-46XAZ10FH User manual

SERVICE MANUAL

PRODUCT CODE No.

REFERENCE No.:SM0915135

1 682 350 17: PAL-BG

NTSC(AV)

FILE NO.

PRODUCT CODE No.

LCD-46XAZ10FH

LCD TV

CONTENTS

Safety precautions………………………………………………………………………..…

Alignment instructions …………………………….…….…………………………………

Instruction of software upgrading & boot burning ....................................................

Working principle analysis of the unit……………………………….………….………….

Block diagram…………………………………..………………………………….…………

IC block diagram………………………………………………………………………..……

Wiring diagram …………………………………………………………………………….

Troubleshooting guide ………………………………………………………………..……

Schematic diagram…………………………………………………………………………

APPENDIX-A: Assembly list

APPENDIX-B: Exploded View

3

5

13

19

20

21

29

30

33

Safety precautions

1. Instructions

Be sure to switch off the power supply before replacing or welding any components or

inserting/plugging in connection wire. Anti static measures must be taken (throughout the entire

production process!):

a) Do not touch here and there by hand at will;

b) Be sure to use anti static electric iron;

c) It’s necessary for the welder to wear anti static gloves.

Please refer to the part list before replacing components that have special safety requirements.

Do not replace with different components with different specs and type at will.

2. LCD servicing precautions

2.1 Screens are different from one model to another and therefore not interchangeable. Be sure to

use the screen of the original model for replacement.

2.2 The operation voltage of LCD screen is 700-825V. Be sure to take proper measures in

protecting yourself and the machine when testing the system in the course of normal operation or

right after the power is switched off. Please do not touch the circuit or the metal part of the module

that is in operation mode. Relevant operation is possible only one minute after the power is

switched off.

2.3 Do not use any adapter that is not identical with the TV set. Otherwise it will cause fire or

damage to the set.

2.4 Never operate the set or do any installation work in bad environment such as wet bathroom,

laundry, kitchen, or nearby fire source, heating equipment and devices or exposure to sunlight etc.

Otherwise bad effect will result.

2.5 If any foreign substance such as water, liquid, metal slices or other matters happens to fall into

the module, be sure to cut the power off immediately and do not move anything on the module lest

it should cause fire or electric shock due to contact with the high voltage or short circuit.

2.6 Should there be smoke, abnormal smell or sound from the module, please shut the power off

at once. Likewise, if the screen is not working after the power is on or in the course of operation,

the power must be cut off immediately and no more operation is allowed under the same

condition.

2.7 Do not pull out or plug in the connection wire when the module is in operation or just after the

power is off because in this case relatively high voltage still remains in the capacitor of the driving

circuit. Please wait at least one minute before the pulling out or plugging in the connection wire.

2.8 When operating or installing LCD please don’t subject the LCD components to bending,

twisting or extrusion, collision lest mishap should result.

2.9 As most of the circuitry in LCD TV set is composed of CMOS integrated circuits, it’s necessary

to pay attention to anti statics. Before servicing LCD TV make sure to take anti static measure and

ensure full grounding for all the parts that have to be grounded.

2.10 There are lots of connection wires between parts behind the LCD screen. When servicing or

moving the set please take care not to touch or scratch them. Once they are damaged the screen

Attention: This service manual is only for service personnel to take reference with. Before

servicing please read the following points carefully.

would be unable to work and no way to get it repaired.

If the connection wires, connections or components fixed by the thermotropic glue need to

disengage when service, please soak the thermotropic glue into the alcohol and then pull them

out in case of dagmage.

2.11 Special care must be taken in transporting or handling it. Exquisite shock vibration may lead

to breakage of screen glass or damage to driving circuit. Therefore it must be packed in a strong

case before the transportation or handling.

2.12 For the storage make sure to put it in a place where the environment can be controlled so as

to prevent the temperature and humidity from exceeding the limits as specified in the manual. For

prolonged storage, it is necessary to house it in an anti-moisture bag and put them altogether in

one place. The ambient conditions are tabulated as follows:

Temperature Operation range 0 ~ +50

o

C

Storage range -20 ~ +60

o

C

Humidity Operation range 20% ~ 85%

Storage range 10% ~ 90%

2.13 Display of a fixed picture for a long time may cause a permanent after-image on the screen,

as commonly called “ghost shadow”. The degree of the after-image varies with the maker of LCD

screen. This phenomenon doesn’t represent failure. This “ghost shadow” may remain in the

picture for a period of time (several minutes). But when operating it please avoid displaying still

picture in high brightness for a long time.

3. Installation precautions

3.1 The front panel of LCD screen is made of glass. When installing it please make sure to put it in

place.

3.2 For service or installation it’s necessary to use specified screw lest it should damage the

screen.

3.3 Be sure to take anti dust measures. Any foreign substance that happens to fall down between

the screen and the glass will affect the receiving and viewing effect

3.4 When dismantling or mounting the protective partition plate that is used for anti vibration and

insulation please take care to keep it in intactness so as to avoid hidden trouble.

3.5 Be sure to protect the cabinet from damage or scratch during service, dismantling or

mounting.

2 Adjustment equipment

Digital multimeter

Signal generator (54200)

PC (presetting FLASH software)

VG848, VG849 (VGA, YPbPr and HDMI signal generator)

DVD player with HDMI output

White balance apparatus (CA210)

Monitor

3 Adjustment flow

3.1 Test voltage of power supply

3.1.1 Main board of non BBY model of which dimension is 26” or bigger than 26”

According to wiring diagram ‘9242KC4201JL’, connect main board, power board, IR board and

key board correctly, switch on power supply, then press key ‘power’ to turn on the TV set.

a）Test voltage of socket X302 each pin in turn, please refer to voltage value as Table 1.

Table 1 Voltage of X302 each pin

X302 Pin1 2 3

4、5 6、7

8 9 10 11 12 13

Vol.

3.3 V～

5.0 V

1.0 V～

3.3 V

0

11.5 V～

12.5V

0

31 V～

33 V

4.7 V～

5.3 V

0

4.7 V～

5.3 V

0

3.3 V～

5.0 V

b）Test voltage of socket X301 each pin in turn, please refer to voltage value as Table 2.

Table 2 Voltage of X301 each pin

X301

Pin1、2 3、4、5

Vol.

23 V～25 V

0

3.1.2 Main board of non BBY model of which dimension is smaller than 26”

According to wiring diagram ‘9222KC4201JL’, connect main board, power board, IR board and

key board correctly, switch on power supply, then press key ‘power’ to turn on the TV set.

a）Test voltage of socket X302 each pin in turn, please refer to voltage value as Table 3.

Table 3 Voltage of X302 each pin

X302 Pin1 2 3

4、5 6、7

8 9 10 11 12 13

Vol.

3.3 V～5.0

V

1.0 V～3.3

V

0

11.5 V～

12.5V

0

31 V～

33 V

4.7 V～5.3

V

0

4.7 V～

5.3 V

0

3.3 V～5.0

V

3.1.3 Main board of BBY model of which dimension is 19” and 22”.

According to wiring diagram ‘9219KC7201JL’, connect main board, power board, IR board and

key board correctly, switch on power supply, then press key ‘power’ to turn on the TV set.

a）Test voltage of socket X302 each pin in turn, please refer to voltage value as Table 4.

Table 4 Voltage of X302 each pin

X302 Pin1 2 3

4、5 6、7

8 9 10 11 12 13

Vol.

3.3 V～5.0

V

0 V～1.5

V

0

11.5 V～

12.5V

0 0

4.7 V～5.3

V

0

4.7 V～

5.3 V

0

3.3 V～5.0

V

Alignment instructions

3.1.4 Main board of BBY model of which dimension is 24”.

According to wiring diagram ‘9224KC7001JL’, connect main board, power board, IR board and

key board correctly, switch on power supply, then press key ‘power’ to turn on the TV set.

a）Test voltage of socket X301 each pin in turn, please refer to voltage value as Table 5.

Table 5 Voltage of X301 each pin

X301 Pin1 2 3

4、5 6、7

8 9 10 11 12 13

Vol.

3.3 V～5.0

V

1.0 V～3.3

V

0

11.5 V～

12.5V

0 0

4.7 V～5.3

V

0

4.7 V～

5.3 V

0

3.3 V～5.0

V

3.1.5 Main board of BBY model of which dimension is 32” and 37”.

According to wiring diagram ‘9232KC7001JL’, connect main board, power board, IR board and

key board correctly, switch on power supply, then press key ‘power’ to turn on the TV set.

a）Test voltage of socket X302 each pin in turn, please refer to voltage value as Table 6.

Table 6 Voltage of X302 each pin

X302 Pin1 2 3

4、5 6、7

8 9 10 11 12 13

Vol.

3.3 V～5.0

V

1.0 V～3.3

V

0

11.5 V～

12.5V

0 0

4.7 V～5.3

V

0

4.7 V～

5.3 V

0

3.3 V～5.0

V

b）Test voltage of socket X301 each pin in turn, please refer to voltage value as Table 7.

Table 7 Voltage of X301 each pin

X301

Pin1、2 3、4、5

Vol.

23 V～25 V

0

3.2 Adjustment flow chart as Fig.1

Fig. 1 Adjustment flow

Check if FLASH has been burned

Product main board on line

General assembly and adjustment

White balance adjustment

Connect to central signal source, check if each function of TV, such

as omitted program, analog parameter control, etc. is normal? Check

if output of earphones, speakers are normal?

Input HI definition signal (mode), check if each

function of YPbPr is normal?

Input VGA signal, check if display and each

function, such as analog parameters control, H/V

center, etc., are normal?

Input AV/S-VIDEO signal, check if each function

of both channels are normal?

Insert U disk, check if functions of MP3 and JPEG

are normal?

Check accessories and packing

Input HDMI signal, check if display and each

function, such as analog parameters control, H/V

Setting before leaving factory

4 Adjustment instruction

4.1 Unit adjustment

4.1.1 According to wiring diagram ‘9242KC4201JL’ , ‘9222KC4201JL’, ‘9219KC7201JL’ ,

‘9224KC7001J’ or ‘9232KC7001JL’, connect main board, power board, key board and IR board

correctly, switch on power supply, check if display is normal?

4.1.2 Instruction of factory menu

a）First press key ‘Program source’, then press number keys “2、5、8、0” in turn to enter initial

factory menu;

b）Press keys “” and “” to move cursor to each adjustment page of initial factory menu, then

press “” to enter into its adjustment menu;

c）Press keys “” and “” to move cursor upwards or downwards within any adjustment page;

d）Press keys “” and “” to adjust any item when cursor is moved onto it;

e）Press key “Menu” to exit to initial menu from any adjustment page;

f）Press key “Exit” to exit from factory menu in any case;

g）Set item “Aging Mode” as “On” to enter into factory aging mode.

4.2 White balance adjustment

4.2.1 Before adjustment

The unit should be working for above 30 minutes to be in stabler state; Use apparatus CA210 to

adjust white balance;

For model of which dimension is bigger than 26”, only 9300K color temperature (that is “normal”)

is needed adjustment, To guarantee BBY test requirements to be met when color temperature are

12000K and 6500K, make sure that chromaticity coordinates of bright scale are (X=285±5, Y=293±8)

and chromaticity coordinates of dark scale are (X=285±8, Y=293±12);

For model of which dimension is 26” or smaller than 26”, only 8000K color temperature (that is

“normal”) is needed adjustment, To guarantee test requirements to be met when color temperature

are 9300K and 6500K, make sure that chromaticity coordinates of bright scale are X=295±5,

Y=305±8) and chromaticity coordinates of dark scale are (X=295±8, Y=305±12);

4.2.2 White balance adjustment of HDMI channel

Input 16-grey-scale signal with format of 800×600/60 Hz (VG848: Timing is 854，PAT is 921),

enter into submenu “color temperature adjustment” of factory menu;

For model of which dimension is bigger than 26”, select “normal” color temperature (that is

9300K), fix item “G Offset”, adjust items “R Offset, B Offset” to set chromaticity coordinates of the 3

rd

scale as （285±8, 293±12）and guarantee luminance within the range of 3 nit to 5 nit; fix item “G

GAIN”, adjust items “R GAIN, B GAIN” to set chromaticity coordinates of the reverse 3

rd

scale as

（285±8, 293±12）; adjust items “R Offset, B Offset” and “R GAIN, B GAIN” repeatedly until

chromaticity coordinates of both scales are all （285, 293）;

For model of which dimension is 26” and small than 26”, select “normal” color temperature (that is

8000K), fix item “G Offset”, adjust items “R Offset, B Offset” to set chromaticity coordinates of the 3

rd

scale as （295±8, 305±12）and guarantee luminance within the range of 3 nit to 5 nit; fix item “G

GAIN”, adjust items “R GAIN, B GAIN” to set chromaticity coordinates of the reverse 3

rd

scale as

（295±5, 305±8）; adjust items “R Offset, B Offset” and “R GAIN, B GAIN” repeatedly until

chromaticity coordinates of both scales are all （295, 305）;

Set item “ALL COLOR” as “ON” after completing adjustment.

4.2.3 White balance adjustment of YPbPr channel

ADC calibration of SD mode: Input color-bar signal with format of 480i/60 Hz (VG848: Timing is

968，PAT is 918), enter into submenu “ADC adjustment” of factory menu and select item “AUTO

COLOR”, system will begin calibration automatically, please note whether picture and data are

abnormal clearly or not (main abnormal data phenomena are that several data are very different from

the other or about 1000 more than the other); it is failed to calibrate ADC if data are abnormal clearly,

so it is necessary to do the calibration again;

ADC calibration of HD mode: Input color-bar signal with format of 1080i/60 Hz (VG848: Timing is

972，PAT is 918), enter into submenu “ADC adjustment” of factory menu and select item “AUTO

COLOR”, system will begin calibration automatically, please note whether picture and data are

abnormal clearly or not (main abnormal data phenomena are that several data are very different from

the other or about 1000 more than the other); it is failed to calibrate ADC if data are abnormal clearly,

so it is necessary to do the calibration again;

White balance adjustment: Input 16-grey-scale signal with format of 1080i/60 Hz (VG848: Timing

is 972，PAT is 921), check if white balance is normal, if not, enter into submenu “color temperature

adjustment” of factory menu, set item “ALL COLOR” as “OFF”, please refer to step 4.2.2 to adjust

white balance for model of which dimension is 26” , bigger than 26” or smaller than 26” respectively;

Note: Item “ALL COLOR” must not be altered as “ON” again once set as “OFF”.

4.2.4 White balance adjustment of VGA channel

Auto-calibration: Input square signal with format of 800×600/60 Hz (VG848: Timing is 854，PAT is

CROSS) to do calibration automatically in order to make window filled with picture;

ADC calibration: Input monochrome signal with format of 800×600/60 Hz (VG848: Timing is 854，

PAT is 948), enter into submenu “ADC adjustment” of factory menu and select item “AUTO COLOR”,

system will begin calibration automatically, please note whether picture and data are abnormal clearly

or not (main abnormal data phenomena are that several data are very different from the other or

about 1000 more than the other); it is failed to calibrate ADC if data are abnormal clearly, so it is

necessary to do the calibration again;

White balance adjustment: Input 16-grey-scale signal with format of 800×600/60 Hz (VG848:

Timing is 854，PAT is 921), check if white balance is normal, if not, enter into submenu “color

temperature adjustment” of factory menu, set item “ALL COLOR” as “OFF”, please refer to step 4.2.2

to adjust white balance for model of which dimension is 26” , bigger than 26” or smaller than 26”

respectively;

Note: Item “ALL COLOR” must not be altered as “ON” again once set as “OFF”.

4.2.5 White balance adjustment of AV channel

Input 16-grey-scale signal with format of PAL (VG848: Timing is 969，PAT is 921), check if white

balance is normal, if not, enter into submenu “color temperature adjustment” of factory menu, set item

“ALL COLOR” as “OFF”, please refer to step 4.2.2 to adjust white balance for model of which

dimension is 26” , bigger than 26” or smaller than 26” respectively;

Note: Item “ALL COLOR” must not be altered as “ON” again once set as “OFF”.

4.2.6 Auto-white balance adjustment

4.2.6.1 ADC pre-calibration

Enter into factory menu, set “Program source” as “YPbPr”, input color-bar signal with format of

480i/60 Hz (VG848: Timing is 968，PAT is 918), enter into submenu “ADC adjustment” of factory

menu and select item “AUTO COLOR”, system will begin calibration automatically; input color-bar

signal with format of 1080i/60 Hz (VG848: Timing is 972，PAT is 918), enter into submenu “ADC

adjustment” of factory menu and select item “AUTO COLOR”, system will begin calibration

automatically,

Press key “Menu” to be back to upper menu, set “Program source” as VGA”, input monochrome

signal with format of 800×600/60 Hz (VG848: Timing is 854，PAT is 948), enter into submenu “ADC

adjustment” of factory menu and select item “AUTO COLOR”, system will begin calibration

automatically,

4.2.6.2 White balance adjustment (models except LC-19KC72, LC-22KC72)

TV set should be working for above 30 minutes to be in stabler state before white balance

adjustment; connect CA210 to USB port of PC with data line; connect VG848 and TV to COM port of

PC or virtual COM port respectively (default connection: VG848 to COM5,TV to COM1, the

connection can be altered and saved in administrator window with password “xoceco” if necessary);

output signal of VG848 must be sent to AV1, YPbPr, VGA and HDMI1 channels of TV;

Open program file “White_Balance.exe”, load configure file “AdjustConfig.txt”, then connect

CA210, VG848 and TV respectively according to the instruction on interface.

Note: set probe to “0-CAL” before connecting CA210, press “connect CA210”, set probe back to

“MEAS” after prompt “CA-210 connection and calibration are normal !” appears on the left-down side;

BBY channel is used by CA210 for BBY models, for other models, channels except BBY are used by

CA210; please enter into administer window with password “xoceco” to alter and save apparatus

setting if it is different;

At last, press “Begin auto-white-balance-adjustment”, auto-adjustment will be completed until

prompt “Adjustment is successful” appears.

4.2.6.3 White balance adjustment (models except LC-19KC72, LC-22KC72)

TV set should be working for above 30 minutes to be in stabler state before white balance

adjustment; connect CA210 to USB port of PC with data line; connect VG848 and TV to COM port of

PC or virtual COM port respectively (default connection: VG848 to COM5,TV to COM1, the

connection can be altered and saved in administrator window with password “xoceco” if necessary);

output signal of VG848 must be sent to AV1, YPbPr, VGA and HDMI1 channels of TV;

Note: Channel shared by AV/YPBPR must be adjusted respectively.

Open program file “White_Balance.exe”, if current working progress includes AV channel, enter

into channel setting of administer window to make sure no YPBPR576i@60 but AV is chosen, or load

configure file “AdjustConfigAV.txt”; if current working progress includes YPBPR channel, enter into

channel setting of administer window to make sure no AV but YPBPR576i@60 is chosen, or load

configure file “AdjustConfigYPBPR.txt.txt”; then connect CA210, VG848 and TV respectively

according to the instruction on interface.

Note: set probe to “0-CAL” before connecting CA210, press “connect CA210”, set probe back to

“MEAS” after prompt “CA-210 connection and calibration are normal !” appears on the left-down side;

BBY channel is used by CA210 for BBY models, for other models, channels except BBY are used by

CA210; please enter into administer window with password “xoceco” to alter and save apparatus

setting if it is different;

At last, press “Begin auto-white-balance-adjustment”, auto-adjustment will be completed until

prompt “Adjustment is successful” appears.

5 Performance check

5.1 TV port

Connect RF port to central signal source, first enter into channel menu, then auto search

programs, check if there is any omitted program ,output of speakers and picture are normal

5.2 AV/S-Video port

Input AV/S signal to corresponding terminal respectively, check if picture and sound are normal.

5.3 YPbPr/YCbCr port

Input YUV signal from signal general VG848 with YUV format listed as Table 8, check if picture

and sound are normal.

Table 8 YUV signal format

NO. Definition

H. Fre.

kHz

V. Fre.

Hz

Dot-pulse Fre.

MHz

Note

1 720×[email protected]/60 Hz 15.734 59.94/60 13.5 480i(59.94/60p)

2 720×480p@59.94/60 Hz 31.469 59.94/60 27.00 480p(59.94/60p)

3 1280×720p@59.94/60 Hz 44.96 59.94/60 74.18 720p(59.94/60p)

4 1920×1080i@59.94/60 Hz 33.75 59.94 74.25 1080i(59.94/60i)

5 1920×1080p@23.98/24 Hz 27.00 23.98/24 74.25 1080p(23.98/24p)

6 1920×1080p@59.94/60 Hz 67.50 59.94/60 148.50 1080p(59.94/60p)

5.4 VGA port

Input VGA signal from signal general VG848 with VGA format listed as Table 9, check if picture

and sound are normal, if not, enter into menu to do auto-calibration.

Table 9 VGA signal format

NO. Definition

H. Fre.

kHz

V. Fre.

Hz

Dot-pulse Fre.

MHz

Note

1 720×400@70 Hz 31.47 70.08 28.32 DOS

2 640×480@60 Hz 31.50 60.00 25.18 VESA

3 800×600@60 Hz 37.90 60.00 40.00 VESA

4 1024×768@60 Hz 48.40 60.00 65.00 VESA

5

1280×1024@60 Hz 63.98 60.02 108.00 VESA

(only for Full HD panel)

6

1360×768@60 Hz 47.71 60.01 85.50 VESA

(only for 1366X768 panel)

7

1920×1080@60 Hz 67.16 59.96 173.00 VESA

(only for Full HD panel)

5.5 HDMI port

Input HDMIsignal from signal general VG849 with VGA format listed as Table 8&9 , check if

picture and sound are normal

5.6 USB port

Inset U disk, check if JPEG picture and MP3 music are displayed normally

5.7 AV OUT port

Check if picture and sound of AV OUT are normal

5.8 Check other functions

Check if time-on/off, sleeping time, picture/sound mode, OSD, still picture/mute and

microcrystalline-magical-picture, etc., are normal.

6 User menu setting before leaving factory

Enter into factory menu, select item ‘Reset’, TV set will be preset automatically before leaving

factory. Be sure to do the step after completing adjustments in factory.

7 Instruction for software burning in factory as Table 10

Table 10 Instruction for software burning in factory

Loc. Part No. Part Type

Instruction for

software function

Burned before

SMT

Method of burning

N104 5272532004 W25X32VSS

Main CPU

program

Yes Burned software with ALL11

Instruction of software upgrade

Instruction of software upgrade for KC# model:

1. Save upgrade file “flash.img” into the root directory of a U disk;

2. Insert the U disk into USB port of TV set, press key “power” until TV set is in

“standby” state, then power on TV set again;

3. Press key “program source” until menu “program source” display, then

press keys “2”, “5”, “8”, “0” by turn to enter into factory menu, please refer to

the following Fig. 1;

Fig. 1 “Program source” menu

Fig. 2 Factory menu

4. Press keys of remote control “▲”,”▼” to select item “ISP”, press key “enter”

to begin updating progress, a prompt “Updating, Pls, Waiting…” is

displaying, wait for a while until menu display (TV set is unable to accept

other operation now), please refer to the Fig. 3;

Fig. 3 Updating prompt

5. TV set will auto-reset after completing update, according to step1 and step

2, enter into factory menu again to confirm updating completion by

checking the time of update file.

Working principle analysis of the unit

RF signal from antenna is sent into TUNER301 to be processed by HF-amplified and

frequency mixing, then IF signal is outputted to SWF Z301 to be IF filtered to get ideal IF

characteristics, then the signal is sent to main chip N101(RTD2674S)-27#,28# to be

amplified by inline IF amplifier and synchronous demodulated to get CVBS.

Video and audio signal from AV, SCART are sent to main chip N101 directly; video and

audio signal from VGA and HDMI1, HDMI2 are also sent to main chip N101 directly.

Main chip N101(RTD2674S) is a special large scale IC with full functions, such as HDMI

interface process, video decoding, video switch selection, A/D and D/A transformation,

interleaved/successive scans, mode transformation, OSD and low-voltage difference

output process, etc.; furthermore, it also has functions of audio selection and process,

MCU, etc.; external video signal is processed by main chip N101(RTD2674S), then 4 pairs

of difference signals and one pair of clock signals are outputted to LCD to display; external

audio signal processed by main chip N101(RTD2674S) is sent to sound amplifier

N308(R2A15112FP) to be amplified and then to speakers.

Block diagram

RTD2674S

Pin List

RTD2674

LQFP-216

E-PAD

U2

QFP216E

AGND_BB1

216

VCM_BB

1

AIO_2L

5

AIO_1R

6

AIO_1L

7

AVDD_BB0_3.3V

2

AIN_5L/LSADC6

3

AIN_3R

10

AIN_3L

11

AIN_2R

12

AIN_2L

13

AIN_1R

14

AIN_1L

15

AOUT_R

16

AOUT_L

17

HPOUT_R

18

HPOUT_L

19

SCART_FSW_0

20

DAC_VDD_3.3V

22

AVOUT_1

23

AVOUT_2

24

DAC_GND

25

ADC2X_GND_3.3V

26

IF_N

27

IF_P

28

ADC2X_VDD

29

PLL_GND

30

XI N

31

XOU T

32

PLL_VDD_3.3V

33

CORE_1.2V

34

SCART_FSW_1

21

USB_AVDD_3.3V

35

HSDM

36

HSDP

37

USB_AVDD_1.2V

38

I2C0_SCL

39

I2C0_SDA

40

IO_3.3V

41

GPIO_A0/RF_AGC

42

GPIO_A1/IF_AGC

43

CORE_1.2V

44

O_FP

45

O_FN

46

O_EP

47

O_EN

48

O_DP

49

O_DN

50

O_CP

51

O_CN

52

O_BP

53

O_BN

54

ADDR5

109

ADDR6

110

ADDR7

111

ADDR8

112

ADDR9

113

ADDR11

114

ADDR12

115

CKE

116

DDR_IO_2.5V

117

CK

118

CK#

119

DM1

120

DDR_IO_2.5V

121

DDR_VREF

122

DQ_15

123

DQ_14

124

DQ_13

125

DQ_12

126

DQ_11

127

DQ_10

128

DDR_IO_2.5V

129

DQ_9

130

DQ_8

131

DQS1

132

CORE_1.2V

133

IO_3.3V

134

LSADC_REF

135

LSADC0/GPIO

136

LSADC1/GPIO

137

STBY_CORE_1.2V

140

GPIO_C0

141

GPIO_C1

142

GPIO_C2

143

GPIO_C3

144

GPIO_C4

145

RESET_IN

146

SPI_CS_N

147

SPI_SCK

148

SPI_DO

149

SPI_DI

150

STBY_CORE_1.2V

151

GPIO_C5

152

GPIO_C6

153

LSADC2/GPIO

138

GPIO_C8

154

IO_3.3V

155

VGA_DDC_SDA

156

VGA_DDC_SCL

157

HDDC1_SDA

158

HDDC1_SCL

159

HDDC0_SDA

160

HDDC0_SCL

161

CEC

162

TMDS_1.2V

163

TMDS_3.3V

164

P1_RX3N/HDMI_CLKN_1

165

P1_RX3P/HDMI_CLKP_1

166

P1_RX2N/HDMI_0N_1

167

P1_RX2P/HDMI_0P_1

168

P1_RX1N/HDMI_1N_1

169

P1_RX1P/HDMI_1P_1

170

P1_RX0N/HDMI_2N_1

171

P1_RX0P/HDMI_2P_1

172

P0_RX3N/HDMI_CLKN_0

173

P0_RX3P/HDMI_CLKP_0

174

P0_RX2N/HDMI_0N_0

175

P0_RX2P/HDMI_0P_0

176

P0_RX1N/HDMI_1N_0

177

P0_RX1P/HDMI_1P_0

178

P0_RX0N/HDMI_2N_0

179

P0_RX0P/HDMI_2P_0

180

TMDS_REXT

181

TMDS_1.2V

182

APLL_VDD_3.3V

183

APLL_GND

184

HSYNC

185

VSYNC

186

ADC_VDD_3.3V

187

VD_VDD_3.3V

188

(VGA_G)VIN_0P

189

VIN_0N

190

(VGA_B)VIN_1P

191

VIN1_N

192

(VGA_R)VIN_2P

193

VIN_2N

194

(Pb)VIN_3P

195

VIN_Y0N

196

(Y)VIN_4P

197

(Pr)VIN_5P

198

(FSC_B/Pb)VIN_6P

199

VIN_Y1N

200

(FSC_G/Pr)VIN_7P

201

(FSC_R/Y)VIN_8P

202

ADC_VDD_1.2V

203

VD_VDD_1.2V

204

VD_GND

205

(SV-C/FSC_CVBS)VIN_11P

206

VIN_A0N

207

(SV-Y)VIN_9P

208

(SV-C)VIN_12P

209

VIN_A1N

210

(CVBS/SV-Y)VIN_10P

211

(CVBS/SV-C)VIN_13P

212

VIN_A2N

213

(CVBS)VIN_14P

214

AVDD_BB1_3.3V

215

O_AP

55

O_AN

56

IO_3.3V

57

E_FP

58

E_FN

59

E_EP

60

E_EN

61

E_DP

62

E_DN

63

E_CP

64

E_CN

65

E_BP

66

E_BN

67

E_AP

68

E_AN

69

CORE_1.2V

70

TCON/GPIO_B0

71

TCON/GPIO_B2

72

TCON/GPIO_B3

73

TCON/GPIO_B4

74

TCON/GPIO_B5

75

TCON/GPIO_B6

76

TCON/GPIO_B7

77

TCON/GPIO_B8

78

IO_3.3V

79

TCON/GPIO_B9

80

TCON/GPIO_B10

81

TCON/GPIO_B12

82

CORE_1.2V

83

DQS0

84

DQ_7

85

DQ_6

86

DDR_IO_2.5V

87

DQ_5

88

DQ_4

89

DQ_3

90

DQ_2

91

DQ_1

92

DQ_0

93

DDR_IO_2.5V

94

DM0

95

WE#

96

CAS#

97

RAS#

98

CORE_1.2V

99

BA0

100

BA1

101

ADDR10

102

ADDR0

103

ADDR1

104

ADDR2

105

ADDR3

106

DDR_IO_2.5V

107

ADDR4

108

E-PAD

217

AIO_2R

4

AIN_4R

8

AIN_4L

9

LSADC4/GPIO

139

IC block diagram

Table 1-1. RTD2674S Pin Assignments – Pin detail description

(I/O Legend: A = Analog, I = Input, O = Output, P = Power, G = Ground)

Pin No Pin Name Type Description Note

1

VCM_BB AP Analog Audio Common Voltage Reference

Connect 1uF to GND

2

AVDD_BB0 AP Analog Baseband Power 3.3V

Analog 3.3V

3

AIN_5L/LSADC6 AI Low Speed ADC input 6

4

AIO_2R AIO Analog Audio input/output 2 (Right Channel)

5

AIO_2L AIO Analog Audio input/output 2 (Left Channel)

6

AIO_1R AIO Analog Audio input/output 1 (Right Channel)

7

AIO_1L AIO Analog Audio input/output 1 (Left Channel)

8

AIN_4R AI Analog Audio input 4 (Right Channel)

9

AIN_4L AI Analog Audio input 4 (Left Channel)

10

AIN_3R AI Analog Audio input 3 (Right Channel)

11

AIN_3L AI Analog Audio input 3 (Left Channel)

12

AIN_2R AI Analog Audio input 2 (Right Channel)

13

AIN_2L AI Analog Audio input 2 (Left Channel)

14

AIN_1R AI Analog Audio input 1 (Right Channel)

15

AIN_1L AI Analog Audio input 1 (Left Channel)

16

AOUT_R AO Analog Baseband Audio Out (Right Channel)

17

AOUT_L AO Analog Baseband Audio Out (Left Channel)

18

HPOUT_R AO Head Phone DAC output (Right Channel)

19

HPOUT_L AO Head Phone DAC output (Left Channel)

20

Scart_FSW_0 AIO SCART RGB Fast Switch Input 0

21

Scart_FSW_1 AIO SCART RGB Fast Switch Input 1

22

DAC_VDD_0 AP Video DAC Power 3.3V

Analog 3.3V

23

AVOUT_1 AP CVBS DAC output1

24

AVOUT_2 AP CVBS DAC output2

25

DAC_GND_0 AP Video DAC GND

26

ADC2X_GND_1 AP IFADC GND

27

IF_N AP IF demod Negative input

28

IF_P AP IF demod Postive input

29

ADC2X_VDD_0 AP IFADC power 3.3V

Analog 3.3V

30

PLL_GND_1 AP XTAL PLL GND

31

XIN AP 27MHz Crystal Input

32

XOUT AP 27MHz Crystal Output

33

PLL_VDD_0 AP XTAL PLL power 3.3V

Analog 3.3V

34

Core_1.2V DP Core Power 1.2V

Digital 1.2V, Power Down@

Power saving

35

AVDD_1 AP USB Power 3.3V

Analog 3.3V

36

HSDM_1 AP USB HOST0 Data Negative

37

HSDP_1 AP USB HOST0 Data Postive

38

LV_USB_1 AP USB Power 1.2V

Analog 1.2V

39

I2C0_SCL DIO Tuner I2C clock

5V tolerance even when

power-off

40

I2C0_SDA DIO Tuner I2C data

5V tolerance even when

power-off

RTD2674S

41

VCC3_0 P PAD I/O Power 3.3V

Digital I/O 3.3V

42

GPIO_A0 DIO GPIO_A0

5V tolerance even when

power-off

43

GPIO_A1 DIO GPIO_A1

5V tolerance even when

power-off

44

Core_1.2V P Core Power 1.2V

Digital 1.2V, Power Down@

Power saving

45

B_FP AO LVDS_Port_B_F_Pair_P

46

B_FN AO LVDS_Port_B_F_Pair_N

47

B_EP AO LVDS_Port_B_E_Pair_P

48

B_EN AO LVDS_Port_B_E_Pair_N

49

B_DP AO LVDS_Port_B_D_Pair_P

50

B_DN AO LVDS_Port_B_D_Pair_N

51

B_CP AO LVDS_Port_B_C_Pair_P

52

B_CN AO LVDS_Port_B_C_Pair_N

53

B_BP AO LVDS_Port_B_B_Pair_P

54

B_BN AO LVDS_Port_B_B_Pair_N

55

B_AP AO LVDS_Port_B_A_Pair_P

56

B_AN AO LVDS_Port_B_A_Pair_N

57

LVDSV P LVDS Power 3.3V

58

A_FP AO LVDS_Port_A_F_Pair_P

59

A_FN AO LVDS_Port_A_F_Pair_N

60

A_EP AO LVDS_Port_A_E_Pair_P

61

A_EN AO LVDS_Port_A_E_Pair_N

62

A_DP AO LVDS_Port_A_D_Pair_P

63

A_DN AO LVDS_Port_A_D_Pair_N

64

A_CP AO LVDS_Port_A_C_Pair_P

65

A_CN AO LVDS_Port_A_C_Pair_N

66

A_BP AO LVDS_Port_A_B_Pair_P

67

A_BN AO LVDS_Port_A_B_Pair_N

68

A_AP AO LVDS_Port_A_A_Pair_P

69

A_AN AO LVDS_Port_A_A_Pair_N

70

Core_1.2V P Core Power 1.2V

Digital 1.2V, Power Down@

Power saving

71

GPIO_B0 DIO GPIO_B0

5V tolerance even when

power-off

72

GPIO_B2 DIO GPIO_B2

5V tolerance even when

power-off

73

GPIO_B3 DIO GPIO_B3

5V tolerance even when

power-off

74

GPIO_B4 DIO GPIO_B4

5V tolerance even when

power-off

75

GPIO_B5 DIO GPIO_B5

5V tolerance even when

power-off

76

GPIO_B6 DIO GPIO_B6

5V tolerance even when

power-off

77

GPIO_B7 DIO GPIO_B7

5V tolerance even when

power-off

78

GPIO_B8 DIO GPIO_B8

5V tolerance even when

power-off

79

VCC3_2 P PAD I/O Power 3.3V

RTD2674S

Page is loading ...

Sanyo LCD-46XAZ10FH User manual

This manual is also suitable for

Sanyo LCD-46XAZ10FH User manual

Related papers

Other documents