Anolis Ambiane™ User manual

Brand: Anolis

Model: Ambiane™

Type: User manual

User manual

Ambiane PW

The unit generates light by means of high power LEDs. The product was designed for indoor use only.

1. Attention

  Theunitmustbeinstalledbyaqualiedelectricianinaccordancewithall

national and local electrical and construction codes and regulations.

The unit was designed for idoor use only.

Avoid looking directly into the LED light beam at close range!

  Donotinstalltheunitnearhighlyinammableliquidsormaterials.

Do not allow anything to rest on the unit.

  Donotinstalltheunitnearanopename.

Do not install the unit in dirty,dusty or badly ventilated location.

  Sucientairaccessingtothehousingoftheunithastobeensured,

there must not be any heat or anti-noise insulation within a 0.6m x 0.6m

  areaaroundtheunit(non-ICratedxture).

Alvays switch o power suply of the unit before connecting or disconnecting the unit

2. Installation

1.Prepareacircularopeninginthelowerceiling(1)asshowninthepicturebelow.

2.InserttheAmbianeunitintotheopening.Fastenthexturebymeansoftwospringfasteners(2)totheopening

Toconnectneededcablestothexture,unscrewtwoscrews(4)fromtheplasticcover(3)andchipneeded

plasticthin-walledcovers(6)oinordertopasscablestotheconnectionblocks(5).

Theconnectionblocks(5)havethefollowingwiring:

Theprimarypowerinputservesforastandardpower(e.g.ArcPowerforAmbiane).

Thesecondarypowerinputservesforabackuppower(incasethatprimarypowerfailed).

If both power inputs are under voltage, the primary power has a priority and the secondary power is disabled.

fthextureissuppliedviathesecondarypower,thelightoutputofthexturecanbesetbyatrimmer.

Thexturecanbecontrolledbyoneofthefollowingmethods:DMX512

0-10V

DALI

ThextureisequippedwithtwoDMXandDALIconnectionblocksforeasyconnectiontoDMXorDALIchain

(In/Outmethod).

DMX connection 0-10V connection Power connection

PCB Function PCB Function PCB Function

0V - Shield 0V 0V + Power +

D+ Signal(+)   D+ +10V    - Power-

D- Signal(-)

3. DMX and DALI address setting and control

The DIP switch, located next to the connection blocks, allows to set a method of control, run test and also allows

toswitchthexturetotheupdatemodeincaseofsoftwareupdate.

DIP 10 - if switched to ON=test light

DIP11-selectionofxturecontrol:OFF=DMX512orDALI,ON=0-10V

DIP12-changefromOFFtoONpositionswitchesthexturetotheupdatemode.

DMX control

TheDMXstartaddress,istherstchannelusedtoreceiveinstructionsfromtheDMXcontroller.Theaddress

maybeanychannelfrom1to512.DMXaddresscanbeseteitherbyDIPswitchorbyRDM.DMXaddress

setbyRDMoverwritesaddresssetbyDIPswitchandviceversa.ThegreenLEDonPCBsignalswayofDMX

addresssettting:

 LEDlights-DMXaddressissetbymeansoftheDIPswitch.

 LEDdoesnotlight-DMXaddressissetbymeansofRDM.

DIP 11 has to be set in OFF position.

ExampleofDMXaddresses:

DALI control

AddressingofthextureismadebymeansofanexternalDALIcontroller.TheexternalDALIcontrollerhasto

sendactivatingcommand(8=ON)ifyouneedtostartthepermanentcontrolofthexture(xturewillnotrespond

toDMXcommands)anddeactivatingcommand(0=OFF)tostopcontrolofthexture.

DIP 11 has to be set in OFF position.

Note:IfDIP11=OFF(xtureiscontrolledbyDMXorDALI),therstcomingcommandswitchesthexturetothe

correspondingoperationmode(DMXoperationbyaDMXcommand,DALIoperationbyaDALIcommand).E.g.

thexturestaysinaDALIoperationandcomingDMXcommandswitchesthexturetoDMXoperation.Next

commandisaDALIcommandandswitchesthexturetotheDALIoperationetc.Ifyouneedthepermanent

DALIoperation,youhavetosendaDALIcommand8tothexture.

0-10V control

DIP 11 has to be set in ON position. 0-10V operation has priority to DALI commands.

4. RDM

ThisxturesupportsRDMoperation.RDM(RemoteDeviceManagement)isabi-directionalcommunication

protocolforuseinDMX512controlsystems,itisthenewopenstandardforDMX512devicecongurationand

status monitoring.

RDMallowsyoutosetDMXaddressandreadoutsoftwareversionofthexture.

5. Anti-glare ring installation

Inserttheantiglarering(1)intothextureuntilthreelocks(2)snapintoslots(3).

6. Adapter ring installation

1.Removebothspringfasteners(2)byunscrewingthefourscrewsM4x10(1).

2.Slidetheadapterring(4)ontothehousingofthexture.Screwthenewfasteners(3)onthehousing.

UseoriginalscrewsM4x10(1).

7. DMX protocol

Channel

Value Function Type of control

0-255

Dimmer

Light intensity coarse 0% -->100% proportional

8. Technical specications

Inputvoltage:     24VDC

Max.powerconsumption:   40W

Beamangle:     67°,80°withanti-glarering

Colourtemperature:    2700K,3200K,4000K,5000K,6500K

Control:     DMX,DALI,0-10V

      RDMcompatible

DMXchannels:     1

TypicalLumenmaintenance:   70%@50,000hours

Ledlifeexpectancy:    minimum50,000hours

Operatingambienttemp.range:  -20°C/+45°C(-4F/+113F)

Operatingtemperature:   75°C@Ambient+35°C(167°F@Ambient+95°F)

Totalheatdissipation:    136BTU/h(calculated)

Cooling:     convection

Totalheatdissipation:    136BTU/h(calculated)

Housing:     alluminium

Weight:     1.8kg

Installationmethod:    viatwospringfasteners

ICrating:     non-ICrated

Power/DMX/DALIconnection:   screwconnectionblockDegsonDG306-5.0-02P

      (Wirerange:22-14AWG(UL),1.5mm

(IEC))

Max.distancebetweenAmbianeand

ArcPowerforAmbiane:   1m(for2x18AWGcable)

Protectionfactor:    IP20(withoutdiuserglass),IP20/IP54(withDiuserGlass)

AmbianewithoutDiuserGlass    AmbianewithDiuserGlass

9. Optional Accessories

ArcPowerforAmbiane(P/N10063035)

Anti-GlareRing(P/N10980386)

DiuserGlassFrosted(P/N10980387)

AdapterRing(230-255mm)(P/N10980388)

10. Maintenance

Keepthextureclean,especiallylightsourceandtheribbedhousing.

11. Dimensions

mm [inch]

Version1.4August28,2017

Specications are subject to change without notice.

Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o. Palackeho 416/20 CZ 75701 Valasske Mezirici

Anolis Ambiane™ User manual

Anolis Ambiane™ User manual

Anolis Ambiane™ User manual

Related papers

Other documents