RAB Lighting WFR6R129FA120WB Operating instructions

RAB Lighting
Brand
RAB Lighting
Model
WFR6R129FA120WB
Type
Operating instructions

This manual is also suitable for

IMPORTANT
WHAT’S IN THE BOX
Fixture (1)
DIAMETER: XX mm
INSTRUCTIONS
TOOLS NEEDED
Edge-Lit Wafer Downlight FA
Driver box (1)
Template (1)
This Edge-Lit Wafer requires very few tools for installation.
A screwdriver and a pair of wirecutters will help to install.
OPTIONAL ACCESSORIES
DLPLATE/SJ
New construction plate for Stud/Joist
DLPLATE/T
New construction or remodel plate for
T-grid ceilings
TO PREVENT ELECTRICAL SHOCK, POWER SHOULD BE TURNED OFF AT THE FUSE BOX BEFORE INSTALLATION.
SAFETY WARNINGS:
Read all product labels and directions.
input rating of the luminaire.
local codes. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• INSTALLATION SHOULD ONLY BE PERFORMED AFTER POWER TO THE FIXTURE HAS BEEN DISCONNECTED.
• These instructions shall be included on an information sheet packaged with each unit.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
WFR6RXX9FA120WS
WFR6RXX9FA120WB
Lumi Sticker (1)
DO NOT TO INSTALL OR OPERATE FLUORESCENT LAMPS IN THIS LUMINAIRE.
AT T TEMP
THIS LUMINAIRE HAS BEEN MODIFIED TO OPERATE LED LAMPS.
REPLACE ONLY WITH RAB Lighting Inc.
RABLIGHTING.COM 888 722-1000
MODEL#
v
Easy Answers
4. Insert the electrical supply cable through the knockout and
secure with a cable connector. Wire driver box (Fig.3), white - white,
black - black, green - green/ground. (For 0-10V dimming circuits,
grey - grey, purple - purple)
INSTALLATION INTRODUCTIONS
ig: 6
5. Place all wiring and connections back in to the box, close the
cover and select desired CCT. (Fig.4)
6. Place the driver box into the ceiling and Connect the
xture to
driver box.
F
Fig: 5
F
(Fig.5)
against the ceiling.
7
(Fig.6)
INSTRUCTIONS
Edge-Lit Wafer Downlight FA
Edge-Lit Wafer
Downlight FA
Fig: 3
3. Open the driver box and remove the knockout(s). (Fig.2)
1. Turn power OFF from the electrical panel before installation.
2. Use template inside box to cut hole in ceiling.(Fig.1)
Fig: 1
Fig: 2
F
Cable connector
power supply
black wire
white wire
green wire
Fig: 4
INSTALLATION INTRODUCTIONS (cont’d)
DIMENSIONAL DRAWINGS
5 1/8”
6 3/4”
7 5/8”
1 3/8”
5 1/2”
3 7/8”
1 3/8”
1/2”
5 1/8”
6 7/8”
7 3/4”
1 3/8”
5 1/2”
3 7/8”
1 3/8”
3/8”
  • Page 1 1
  • Page 2 2

RAB Lighting WFR6R129FA120WB Operating instructions

RAB Lighting
Brand
RAB Lighting
Model
WFR6R129FA120WB
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents