iToma CKS507 User manual

TO PREVENT FIRE OR SHOCK HAZARD , DO NOT USE THIS PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN

BE FULLY INSERTED AND THERE ISNO BLADE EXPOSURE .TO PREVENT FIRE OR

SHOCK HAZARD , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

11.) Use only with the cart, stand, tripod,bracket,or table specified by the manufac-

turer,or sold with the apparatus . When a cart is used, use caution when moving

the cart/apparatus combination to avoid injury from tip-over.

12.) The AC adaptormust not be exposed to dripping or splashing and noobjects

filled with liquids, such as vases, shall be placed on apparatus.

13. ) The AC plug is used as a disconnect device and it must remain

readily accessible during intended use. In order to disconnect the

apparatus from the AC power completely, the AC plug must be

removed from the AC outlet completely.

10.) Refer all servicing to qualified service personnel. Servicing is required when the

apparatus hasbeen damaged in any way,such as power-supply cord or plug is

damaged, liquid has been spilledor objects have fallen into the apparatus,the

apparatus has been exposed to rain or moisture,does not operate normally, or

has been dropped.

plug has twoblades with one wider than the other. A grounding type

1.) Read these instructions . Keep these instructions . Follow all instructions.

Heed all warnings.

2.) Do not use this apparatus near water.

3.) Clean only with dry cloth.

4.) Do not block any ventilation openings. Install in accordance with themanu-

facturer's instructions.

5.) Do not install near any heat sources such as radiators, heaters, stoves, or

other apparatus(including amplifiers) that produce heat.

6.) Do not defeat the safety purpose of the polarized or grounding-type plug.A

polarized

the obsolete outlet.

7.) Protect the power cord from being walked on or pinched particularly at plugs,

conveniencereceptaclesand the point where they exit from the apparatus.

8.) Only use attachments / accessories specified by the manufacturer.

9.) Unplug this apparatus during lightning storms or when unused for long

periods of time.

plug has two blades and a third grounding prong. The wide blade or the third

prong is provided for your safety.

If the provided plug does notﬁt into your outlet, ask an electrician for replace

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only

with the same or equivalent type.

14.) The battery must not be exposed to excessive heat such as sunshine, fire, etc.

Warning

Important Safety Instructions

Remove the radio from the carton and remove all packing material from the radio.

Save the packing material,if possible,in case the radio ever needs to be serviced

or transported.The original carton and packing material is the only safe way to

pack your radio to protect it from damage in transit.

Remove any descriptive labels or stickers on the front or top of the cabinet.

Do not remove any labels or stickers from the back or bottom of the cabinet.

Note the serial number on the bottom of your radio and write this number in the

space provided on the Warranty page of this manual.

Place your radio on a level surface such as a table,desk or shelf,convenient to

an AC outlet,out of direct sunlight,and away from sources of excess heat,dirt,

dust,moisture, humidity, or vibration.

Unwind the Line cord connecting the AC adapter and extend it to its full length.

The FM antenna is built in to this cord.It must be fully extended to provide the best

FM reception.

Unpacking And Set Up

Protect Your Furniture

This model is equipped with non-skid rubber 'feet' to prevent the product from

moving when you operate the controls.These'feet'are made from non-migrating

rubber material specially formulated to avoid leaving any marks or stains on your

furniture. However certain types of oil based furniture polishes, wood preservati-

ves, or cleaning sprays may cause the rubber 'feet' to soften,and leave marks or a

rubber residue on the furniture.To prevent any damage to your furniture we

strongly recommend that you purchase small self-adhesive felt pads, available at

hardware stores and home improvement centers everywhere, and apply these

pads to the bottom of the rubber'feet'before you place the product on fine wooden

furniture.

Power Source

This radio is designed to operate on normal 120V 60Hz AC power only. Do not

attempt to operate the radio on any other power source. You could cause damage

to the radio that is not covered by your warranty. This radio should be connected

to an AC outlet that is always'live'. Do not connect it to an outlet that is controlled

by a wall switch. When the power to the radio is interrupted, the built in lithium

battery takes over to maintain the time and alarm settings. To maximize the life of

the lithium battery keep the radio connected to a 'live' AC outlet at all times.

• Operate controls and switches as

described in the manual.

• Before turning on the power,

make certain that the AC adapter

is properly installed.

• When moving the set, be sure to

first disconnect the AC adapter.

• Avoid installing this unit in places

exposed to direct sunlight or close to

heat radiating appliances such as:

electric heaters, on top of other stereo

equipment that radiates theat, places

lacking ventilation, dusty areas, places

subject to constant vibration and/or

humid or moist areas.

• CKS507 clock radio x 1

• AC Power Adapter 110V-240AC 50/60Hz,DC 5V x1

• User Manual x 1

Preparation For Use

Important Notes

What Inside

TOP PANEL

TIME ZONE

VOL

TIME

SET

MEM.

AL2AL1

STO.

SLEEP

BACK PANEL

22 2420 23

ANT.

AUX IN

USB CHAR.

DC 5V IN

POWER Button

ALARM 1 Radio /Buzzer Indicator

ALARM 2 Radio /Buzzer Indicator

PM Indicator

DAY of WEEK Indicator

AUX Indicator

LOW BATTERY Indicator

MH Indicator

ALARM1/STORE Button

TIME SET Button

SLEEP/TIME ZONE Button

11.

10.

12.

ALARM2/MEMORY Button

13.

SNOOZE/DIMMER Button

21.

22.

20.

19.

18.

17.

16.

15.

14.

FM ANTENNA

SOURCE Button

DC JACK Input

USB CHARGING Port

NIGHT LIGHT Button

SET/TURN UP Button

VOLUME- Button

SET/TURN DOWN Button

VOLUME+ Button

BACKUP BATTERY

Compartment

(located on back of unit)

23.

AUX IN Jack

24.

FRONT PANEL

Location of Controls and Indications

OFF : Only time was shown on the display

Power Source

When the clock is connected to the AC outlet for the first time the

display will default Stand by mode.

ON : Radio or Auxiliary mode

Press the button to ON/OFF the unit

Display radio frequency

“AUX” means into Auxiliary Mode

Preparation for Use

AC adapter’Plug

AC outlet

Please refer to AUX IN function in later page

All Daylight Saving and Leap Year adjustment are made automati-

cally by the InteliSet computer as follow：

Start of Daylight Saving time：

At 2:00 AM on the 2nd Sunday in March, the clock will automatica-

lly advance to 3:00 AM

End of Daylight Saving time：

At 3:00 AM on the 1st Sunday in November, the clock will automa-

tically reset to 2:00 AM

Leap Year：

At 12:00 Midnight on February 28th, the calendar display will

change to''2.29''.

Initial Time Setting

IMPORTANT : The first time you connect your new InteliSet Clock

radio to the AC outlet the internal computer will automatically set the

time correctly for the Eastern Time Zone,which is the initial default

setting.The display will scan for a few seconds and then show the

correct Day and Tme in the Eastern zone . If you live in the Eastern

Time Zone which is identical to what is displayed when pressing and

holding the TIME ZONE button , your clock will automatically be

correctly set . Otherwise you must change the default zone display

to your own zone.After resetting the time zone this one time,it will

not be necessary to repeat,even after a power interruption.

There are 7 time zones programmed into your clock radio as follows:

UTC-6 - Atlantic Time - ZONE 1 UTC-5 - Eastern Time - ZONE 2

UTC-4 - Central Time - ZONE 3 UTC-3 - Mountain Time - ZONE 4

UTC-2 - Pacific Time - ZONE 5 UTC-1 - Yukon (Alaska) - ZONE 6

UTC - Hawaiian Time - ZONE 7

Under the Standby Mode (OFF)

VOL+

VOL-

TIME ZONE

Press and hold

SLEEP

Setting the Time Zone

Daylight Saving and Leap Year

Adjustments

Resetting time

Date TimeYear

Press and Hold “TIME SET” until the Year Display blink

Press “TIME SET” and the Month/Date Display will blink

Press “TIME SET” and the Time Display

will blink

Press “ ” “ ” to adjust Year

Press “ ” to adjust Month

Press “ ” to adjust Date

Press “ ” to adjust Hour

Press “ ” to adjust Minutes

If you want to change the Time Zone, please refer to "SETTING

THE TIME ZONE”

VOL+

VOL-

TIME ZONE

UP or DOWN

TIME

SET

Date and Year Display:

Year, Month/Date,Time

Check the current time:

Press st1

YEAR

MONTH/DATE

Press nd2

TIME

Press rd3

VOL+

VOL-

TIME ZONE

TIME

SET

Setting the Time

Please press the Power button to turn OFF the unit

before operating

Press and hold

When it is in standby mode,

Adjustment the Wake up times and Alarm Week Mode

Hour Minutes

Minutes

VOL+

VOL-

TIME ZONE

Hour

Press and hold

Week mode

AL1

STO.

Setting the Alarm

Please press the Power button to turn OFF the unit

before operating

Press and Hold "AL1" or "AL2",then press SOURCE button " "

to adjust: Single Day (Monday, Tuesday, Wednesday, ....Sunday),

Weekdays (Monday to Friday),

Weekends (Saturday and Sunday) ,

Everydays (Monday to Sunday).

Everydays

AL 1 or AL2 On AL 1 or AL2 Off

VOL+

VOL-

TIME ZONE

When the Alarm mode is ON and active,press SNOOZE button

will temporarily turn OFF the alarm sound,but it will be active

again after every 9 minutes until 1 hour(Press the Power button

to turn OFF the SNOOZE mode when alarm is active)

To completely turn off the alarm,keep pressing the AL1

or AL2 until the Buzzer or Music light is OFF.

Keep pressing AL1 or AL2 to turn ON the Alarm Mode.

When Buzzer lights on,the wake up Buzzer alarm will be ON.

When Radio lights on,the wake up Radio alarm will be ON.

Snooze Setting

Press and Hold “AL1”or “AL2”,then press VOL+ or VOL- to

adjust the alarm volume level.

Adjust The Alarm Volume Level

UP or DOWN

VOL+

VOL-

TIME ZONE

AL1

STO.

Press

Power on:

Switch to Radio Mode

(Press SOURCE button)

Tuning the Stations

(Either press TUNE UP or TUNE DOWN)

VOL+

VOL-

TIME ZONE

Please press the Power button to turn ON the unit

and press SOURCE button to change to Radio

Mode before operating

VOL+

VOL-

TIME ZONE

When station was found, it will stop automatically, press and hold

for 2 second again, it will go for the next station.

Scanning the Stations

(Press the TUNE UP button for 2 seconds)

Listen to the Radio

Press 2s

VOL+

VOL-

TIME ZONE

Press

Recall favorable stations from memory

Press the AL2/MEM. button, Program number will be shown on

the display, press TUNE UP or TUNE DOWN to select your

stored program number and listen to your favorable station.Keep

the clock radio away from other electronic devices to avoid radio

interference.For better reception,fully extend and adjust the

position of the FM antenna.

VOL+

VOL-

TIME ZONE

MEM.

AL2

Storing favorable stations to memory

(10 stations can be stored)

UP or DOWN

VOL+

VOL-

TIME ZONE

At Radio Mode, press and hold TUNE UP or TUNE DOWN

button to search for your desired station.

Press the AL1/STO. button, Program Number "P01" will be

blinking on the display, press TUNE UP or TUNE DOWN

to change the program number from "P01" to "P10", once you

have selected the desired program number, press the AL1/

STO. again and the favorable station will be stored to the

selected program number.

VOL+

VOL-

TIME ZONE

AL1

STO.

Press

Press exit sleep mode off

Countdown display(Show once per every 10 minutes)

Press the SLEEP button and you will see from 10,

20, to 90 minutes then OFF, Timer will count down

from the selected minutes by listening to Radio.

Please press the Power button to turn ON the unit to

either Radio or Auxiliary Mode before operating

VOL+

VOL-

TIME ZONE

Sleep mode setting

VOL+

VOL-

TIME ZONE

SLEEP

When the brightness of the surrounding environment changes,

Dimmer Control will automatically adjust the brightness of LED

Display.Brightness of LED Display can also be adjusted by

pressing the SNOOZE / DIMMER button, there are 3-steps of

brightness can be chosen (HIGH - MEDIUM - LOW). Please be

reminded that the changes of brightness will not be effective if

the surrounding environment is very dark.

Dimmer Control(press1/press2/press3)

Low

VOL+

VOL-

TIME ZONE

Auto-tuning

High

VOL+

VOL-

TIME ZONE

Auto-tuning

Sleep Mode

3-Steps Auto Dimmer Control

Press

Press SOURCE button until "AUX" appear on LED display,

connect your audio or mobile device and play music through the

clock with 3.5mm earphone jack.

VOL+

VOL-

TIME ZONE

VOL+

VOL-

TIME ZONE

Night Light turn on / off

AUX IN (Auxiliary Input)

You can connect your device to this unit for charging

Note: Output 5V up to 1.5A for charging

mobile phone or portable

digital audio player.

USB for Charging

Press

The battery backup is intended for short power outages only.The

unit’s primary functions cannot run on the battery backup alone.

This unit uses a button cell battery that will last up to 1 year and

maintains the time.

Changing the Lithium Battery

When the LOW BATTERY sign blinks , you should change

the battery that is used for backup clock and alarm setting .

Resetting The Clock After A Total Memory Loss

If you do not change the built in lithium battery within a reasonable

period of time afteryou see the warning indicator, the lithium

battery may become exhausted and will no longer be able to sup-

ply back up power to the clock radio internal computer.If the unit is

disconnected from the AC outlet after the battery is exhausted, or

if a power interruption occurs, the clock radio memory will be lost

and the clock will need to be reset when the power is restored.

Care Of Cabinets

If the cabinet becomes dusty,wipe it with a soft cloth.If the cabinet

becomes smudged or dirty, clean it with a soft, slightly dampened

cloth . Never allow water or any liquid to get inside the cabinet.

Never use any abrasive cleaners or cleaning pads as these will

damage the finish of your radio.

Lithium Battery Precautions

• Dispose of the old battery properly.Do not leave it lying around

where a young child or pet could play with or swallow it. If the

battery is swallowed, contact a physician immediately.

• The battery may explode if mistreated. Do not attempt to

recharge it or disassemble it.

Do not dispose of the old battery in a fire.

The apparatus must not be exposed to dripping or splashing and

objects filled with liquids, such as vases, must not be placed on

the apparatus.

This marking indicates that this product should not be

disposed of with other household wastes throughout the

country .To prevent possible harm to the environment or

human health from uncontrolled waste disposal,recycle

this unit responsibly so as to promote the re-use of

material resources . To return your used device , please

use return and collection systems or contact the retailer

where the product was purchased as they know how to

safely recycle this product.

Care and Maintenance

Press and Hold “TIME SET” until the Year Display blink

Press “TIME SET” and the Month/Date Display will blink

Press “TIME SET” and the Time Display

will blink

Press “ ” “ ” to adjust Year

Press “ ” to adjust Month

Press “ ” to adjust Date

Press “ ” to adjust Hour

Press “ ” to adjust Minutes

VOL+

VOL-

TIME ZONE

UP or DOWN

TIME

SET

Press and hold

iTOMA (Hong Kong) Company Limited (iTOMA) warrants to be

original consumer of this iTOMA product that it will furnish a

replacement for, or, at its sole option, repair any part which proves

(upon inspection by iTOMA)to be defective under normal use

within 1 year of the original purchase date.This warranty does not

apply to appearance items,including,but not limited to, antennas,

knobs, cabinets, or cases, and in the case of batteries, for damage

caused by leaking batteries. It also does not apply to the product,

or to any part thereof, that has been damaged through misuse or

negligence.Furthermore,this warranty will become invalid if,in the

judgment of iTOMA the product or any part thereof has been

installed incorrectly, repaired or altered by other than iTOMA

Service Department.This warranty gives you specific legal rights

and you may also have other rights which vary from state to state.

Some states do not allow the exclusion or limitation of incidental or

consequential damages or limitations on how long an implied

warranty lasts, so the above exclusions and limitation may not

apply to you.

Power adapter............................................................. DC5V IN

USB output.................................................................. 5V

FM Frequency...................................................

Back up battery (time back up)...................................

Output power...............................................................

Speaker Impedance............................................................

Unit size..........................................

1.5A

87. 5 - 108MHz

1xCR2032

300mW

158W X 90H X 55D (mm)

PLEASE SAVE THIS CARD TOGETHER WITH ORIGINAL DATED

PROOF OF PURCHASE FOR YOUR RECORDS AND FOR

CUSTOMER SERVICE.

info@itoma.com.hk

Please contact iTOMA (Hong Kong) Company Limited,

For Service, Warranty, or Product Information,

Speciﬁcations

1-Year Limited Warranty

Daylight Saving Time is NOT observed in Hawaii, American Samoa, Guam,

Puerto Rico, the Virgin Islands and in, most of Arizona, with exception of the

Navajo Indian Reservation in Arizona. Beginning in 2007, this Clock Radio

will automatically advance by one hour at the beginning of Daylight Saving

Time on the second Sunday in March. And it will automatically return to

Standard Time on the first Sunday in November. If you live in an area that

does not observe Daylight Saving Time it will be necessary for you to

manually set the clock back one hour at the beginning of the Daylight Saving

Time, and forward one hour at the end of Daylight Saving Time. A simple way

to do this is to change the TIME ZONE setting. Set the clock to the next higher

numbered time zone at the beginning of Daylight Saving Time, and set the

clock back to your correct time zone at the end of Daylight Saving Time.

IMPORTANT NOTICE

iToma CKS507 User manual

Related papers

Other documents