QSC E10 Quick start guide

Type
Quick start guide

This manual is also suitable for

E Series
Quick Start Guide
Input Configuration
E Series two-way loudspeakers and subwoofers are designed for externally powered operation. Pass-throughs permit connection to multiple loudspeakers. The
two-way models feature internal passive crossovers for full-range operation. To use them with subwoofers, use an active crossover and separate amplification to
split the subwoofer frequencies and the remainder of the audio spectrum.
PLD and GXD Series amplifiers have E Series voicings available in their presets and loudspeaker profiles. TouchMix digital mixers also have E Series voicings
available, for use in systems that don't have PLD or GXD Series amplifiers.
E Series E10, E12, E15, E215 Block Diagram and Input Plate
— Figure 1 —
LF
E215 only
DEEP LPF
HPF
HF
LPF
LF
NL4
Barrier
Strip
NL4
1
1
1
1
2
2
2
2
E Series E18sw, E218sw Block Diagram and Input Plate
— Figure 2 —
LF
LF
NL4
Barrier
Strip
NL4
1
1
1
1
E218-sw only
2
2
2
2
TD-000525-00-C
*TD-000525-00*
2
TD-000525-00-C
Connections
Full Range Stereo System
— Figure 3 —
GXD Preset
ST SAT FULLRANGE
R
Input
L
NL4
Amplifier
1
1
2
2
NL4
Speaker
1
1
2
2
NL4
Amplifier
1
1
2
2
NL4
Speaker
1
1
2
2
Single Channel, Sub / Satellite Option 1
— Figure 4 —
Input
GXD Preset
SUB SAT nn HZ
NL4
Amplifier
1
1
2
2
NL4
Speaker
1
1
2
2
NL4
Amplifier
1
1
2
2
NL4
Speaker
1
1
2
2
GXD Series power amplier preset:
P6 ST E10 (stereo E10)
P10 ST E12 (stereo E12)
P12 ST E12 DANCE (stereo E12 dance)
P14 ST E15 (stereo E15)
P16 ST E15 DANCE (stereo E15 dance)
GXD Series power amplier preset:
P3 SUB SAT 80HZ
3
TD-000525-00-C
Single Channel, Sub / Satellite Option 2
— Figure 5 —
GXD Preset
SUB SAT nn HZ
Input
Cross-wired 1 - 2, 2 - 1
NL4
Amplifier
1
1
2
2
NL4
Speaker
1
1
2
2
NL4
Amplifier
1
1
2
2
NL4
Speaker
1
1
2
2
Dual Channel, Sub / Satellite System
— Figure 6 —
GXD Preset
ST SUB nn HZ
To Left
Subwoofer
To Right
Subwoofer
GXD Preset
ST SAT nn HZ
To Right
Satellite
To Left
Satellite
R
Input
L
NL4
Amplifier
NL4
Speaker
1
1
2
2
1
1
2
2
NL4
Amplifier
1
1
2
2
NL4
Speaker
1
1
2
2
GXD Series power amplier preset:
P7 ST E10 + SUB
P8 ST E10 DANCE + SUB
P11 ST E12 + SUB
P12 ST E12 DANCE + SUB
P15 ST E15 + SUB
P 17 ST E15 DANCE + SUB
GXD Series power amplier preset:
P3 SUB SAT 80HZ
GXD Series power
amplier preset:
P18 ST E18 SUBS
4
TD-000525-00-C
Dual Channel, Sub / Satellite System with 4-channel PLD
— Figure 7 —
PLD Series power amplier
preset:
F11 Dual bi-amp mode
PLD Series power amplier
loudspeaker proles:
CH A
E18sw
E218sw
CH B
E10 +SUB
E12 +SUB
E12 dance +SUB
E15 +SUB
E15 dance +SUB
E215 +SUB
E215 dance + SUB
CH C
E18sw
E218sw
CH D
E10 +SUB
E12 +SUB
E12 dance +SUB
E15 +SUB
E15 dance +SUB
E215 +SUB
E215 dance + SUB
5
TD-000525-00-C
Pole Mounting
The E Series loudspeakers (E10, E12, E15) can be mounted above the E18sw or
E218sw subwoofer using the 24-inch pole included with the subwoofer.
NOTE: The E215 loudspeaker does not offer a pole mounting option.
WARNING!:
This pole, if used inappropriately, may
result in the loudspeaker system being top-heavy and
hazardous. Ensure that your system will resist tipping
and that it sits on a solid, level surface.
WARNING!:
Always use two persons to lift the
loudspeaker onto the pole.
Do not move a subwoofer if a loudspeaker and pole are
mounted on it.
Refer to — Figure 8
1. Place the subwoofer (1) on a solid level surface positioned where you want
to use it.
2. Screw the threaded end of the 24-inch mounting pole (3) clockwise into the
pole-mounting bracket (2) on top of the subwoofer. Hand tighten only.
3. Select one of the two pole mount cups on the E Series loudspeaker:
The rear cup (4) has no tilt.
The front cup (5) gives a downward tilt of 10°.
4. Carefully place the loudspeaker onto the pole.
Installation Options
The following options require purchasing an accessory kit designed for the
E Series loudspeakers.
Yoke Mounting the Loudspeakers
A yoke accessory allows the E10, E12, or E15 to be mounted on a surface, such
as a wall or ceiling. The E18-sw and E218-sw subwoofers cannot be yoke-
mounted. Each model has a corresponding yoke accessory kit:
E10 Yoke Accessory Kit
E10 Yoke
E12 Yoke Accessory Kit
E12 Yoke
E15 Yoke Accessory Kit
E15 Yoke
Suspending the Loudspeakers
A pair of E10, E12, and E15 loudspeakers can be suspended using the M8 Suspension Kit
M8 KIT A
, which contains six eye bolts and six washers.
To suspend an E215 loudspeaker, use the M10 KIT-W, which contains three eye bolts.
The E18sw and E218sw subwoofers cannot be suspended.
Always consult a licensed and qualified rigger or structural engineer before suspending any loudspeaker.
Subwoofer Casters and Kits
Optional casters are available to install on the subwoofer models to make them more mobile and ideal for use in portable sound systems.
The E18sw subwoofer uses a kit of four 3-inch casters with 16 mounting screws, QSC part number FG-000972-00 (one kit needed per subwoofer).
The E218sw subwoofer uses a kit of two locking and two non-locking 4-inch casters with 16 mounting screws, QSC part number FG-901156-00 (one kit needed per
subwoofer).
— Figure 8 —
6
TD-000525-00-C
Mailing Address:
QSC, LLC
1675 MacArthur Boulevard
Costa Mesa, CA 92626-1468 USA
Telephone Numbers:
Main Number: +1 (714) 754-6175
Sales & Marketing: +1 (714) 957-7100 or toll free (USA only) (800) 854-4079
Customer Service: +1 (714) 957-7150 or toll free (USA only) (800) 772-2834
Facsimile Numbers:
Sales & Marketing FAX: +1 (714) 754-6174
Customer Service FAX: +1 (714) 754-6173
World Wide Web:
www.qsc.com
E-mail:
© 2016 QSC, LLC. All rights reserved. QSC and the QSC logo are registered trademarks of QSC, LLC in the U.S. Patent and
Trademark office and other countries. All other trademarks are the property of their respective owners.
http://patents.qsc.com.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

QSC E10 Quick start guide

Type
Quick start guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI