Lexmark C910 Finisher Compatibility Manual

Card Stock & Label Guide

Laser Printers

October 2012 www.lexmark.com

Edition notice

October 2012

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL,

INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED

TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of

express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these

changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any

time.

References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all

countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product,

program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual

property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services,

except those expressly designated by the manufacturer, are the user’s responsibility.

For Lexmark technical support, visit

http://support.lexmark.com.

For information on supplies and downloads, visit

www.lexmark.com.

Trademarks

Lexmark, Lexmark with diamond design, MarkVision, Optra, and Prebate are trademarks of Lexmark International, Inc., registered in the

United States and/or other countries.

Diamond Fine and WinWriter are trademarks of Lexmark International, Inc.

All other trademarks are the property of their respective owners.

GOVERNMENT END USERS

The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer

Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as

applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software

and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only

those rights as are granted to all other end users pursuant to the terms and conditions herein.

Contents

Edition notice...............................................................................................2

Overview.....................................................................................................7

Introduction..............................................................................................................................................7

General information.....................................................................................8

Paper and label industry............................................................................................................................8

Printing volumes........................................................................................................................................8

Testing print material................................................................................................................................8

Design factors............................................................................................................................................9

Pick roller technology..............................................................................................................................11

Maintenance procedures........................................................................................................................14

Troubleshooting......................................................................................................................................14

Card stock..................................................................................................16

Weight.....................................................................................................................................................16

Grain orientation.....................................................................................................................................17

Coatings...................................................................................................................................................18

Offset powders........................................................................................................................................19

Labels.........................................................................................................20

Label characteristics................................................................................................................................20

Printing on labels.....................................................................................................................................20

Duplexing paper labels............................................................................................................................20

Primary rib pattern design guidelines for reference edge alignment.....................................................22

Label components...................................................................................................................................23

Label design guidelines...........................................................................................................................25

Printer specifications..................................................................................32

Lexmark C500n........................................................................................................................................32

Lexmark C510..........................................................................................................................................33

Lexmark C520, C522, and C524...............................................................................................................34

Lexmark C530, C532, and C534...............................................................................................................36

Lexmark C540, C543, C544, and C546dtn...............................................................................................38

Lexmark C720..........................................................................................................................................40

Contents 3

Lexmark C734 and C736..........................................................................................................................42

Lexmark C746 and C748..........................................................................................................................44

Lexmark C750..........................................................................................................................................46

Lexmark C752..........................................................................................................................................48

Lexmark C760 and C762..........................................................................................................................51

Lexmark C770, C772, C780, and C782.....................................................................................................53

Lexmark C792e, C792de, C792dte, and C792dhe...................................................................................54

Lexmark C910..........................................................................................................................................56

Lexmark C912..........................................................................................................................................58

Lexmark C920..........................................................................................................................................59

Lexmark C925..........................................................................................................................................61

Lexmark C935..........................................................................................................................................62

Lexmark C950..........................................................................................................................................64

Lexmark CS310n, CS310dn, CS410n, CS410dn, and CS510de.................................................................65

Lexmark CX310n, CX310dn, CX410e, CX410de, CX410dte, CX510de, CX510dhe, and CX510dthe.........67

Lexmark E120..........................................................................................................................................69

Lexmark E220..........................................................................................................................................70

Lexmark E230, E232, E234(n), E330, and E332n.....................................................................................71

Lexmark E238, E240, E240n, E340, and E342n........................................................................................72

Lexmark E250, E350, and E450n.............................................................................................................73

Lexmark E260, E260d, E260dn, E360d, E360dn, E460dn, E460dw, and E462dtn...................................74

Lexmark E320, E322................................................................................................................................75

Lexmark E321, E323................................................................................................................................76

Lexmark MS310d, MS310dn, MS410d, MS410dn, MS510dn, MS610dn, and MS610de........................77

Lexmark MS710 and MS711....................................................................................................................79

Lexmark MS810, MS811, and MS812......................................................................................................82

Lexmark MX310dn, MX410de, MX510de, MX511de, MX511dhe, MX610de, MX611de, and

MX611dhe...........................................................................................................................................84

Lexmark MX710, MX711, MX810, MX811, and MX812..........................................................................86

Lexmark T420..........................................................................................................................................89

Lexmark T430..........................................................................................................................................91

Lexmark T520, T522................................................................................................................................93

Lexmark T620, T622................................................................................................................................96

Lexmark T630, T632, T634......................................................................................................................99

Lexmark T640, T642, T644....................................................................................................................102

Lexmark T650, T652, T654, and T656dne..............................................................................................104

Lexmark W812.......................................................................................................................................107

Contents 4

Lexmark W820.......................................................................................................................................108

Lexmark W840.......................................................................................................................................109

Lexmark W850.......................................................................................................................................111

Lexmark X203n and X204n....................................................................................................................113

Lexmark X215........................................................................................................................................114

Lexmark X264dn, X363dn, X364dn, and X364dw..................................................................................116

Lexmark X422........................................................................................................................................118

Lexmark X463de, X464de, X466dte, and X466dtwe.............................................................................119

Lexmark X500 and X502n......................................................................................................................121

Lexmark X543, X544, and X546dtn........................................................................................................122

Lexmark X548........................................................................................................................................124

Lexmark X560........................................................................................................................................125

Lexmark X642e......................................................................................................................................127

Lexmark X644e, X646e..........................................................................................................................129

Lexmark X651de, X652de, X654de, X656de, and X658de.....................................................................132

Lexmark X734, X736, and X738.............................................................................................................135

Lexmark X746 and X748........................................................................................................................137

Lexmark X782........................................................................................................................................139

Lexmark X792de, X792dte, X792dtfe, X792dtpe, X792dtme, and X792dtse........................................141

Lexmark X850, X852e, and X854e.........................................................................................................143

Lexmark X860e, X862e, and X864e.......................................................................................................145

Lexmark X925........................................................................................................................................147

Lexmark X940 and X945........................................................................................................................149

Lexmark X950........................................................................................................................................150

Optra plus, 4039, 4029, 4019, WinWriter 600 printers.........................................................................151

Optra C..................................................................................................................................................155

Optra C710............................................................................................................................................155

Optra Color 1200...................................................................................................................................157

Optra E, Ep.............................................................................................................................................158

Optra E310, E312...................................................................................................................................159

Optra Es special media printer..............................................................................................................160

Optra K 1220.........................................................................................................................................161

Optra M410, M412................................................................................................................................162

Optra N..................................................................................................................................................164

Optra S...................................................................................................................................................165

Optra SC 1275........................................................................................................................................168

Optra T..................................................................................................................................................169

Contents 5

Optra W810...........................................................................................................................................172

Glossary...................................................................................................174

Index........................................................................................................178

Contents 6

Overview

Introduction

This document provides guidelines to help you select appropriate print materials for the following Lexmark laser

printers.

Series Printer models

4019 All

4029 All

4039 10 plus All

4039 12C All

C series C500, C510, C520, C522, C524, C530, C532, C534, C540, C546dtn, C543, C544, C720, C734, C736,

C746, C748, C750, C752, C760, C762, C770, C772, C780, C782, C792e, C792de, C792dte, C792dhe,

C910, C912, C920, C925, C935, C950, CS310n, CS310dn, CS410n, CS410dn, CS510de, CX310n,

CX310dn, CX410e, CX410de, CX410dte, CX510de, CX510dhe, CX510dthe

E series E120, E220, E230, E232, E234(n), E238, E240, E250, E260, E320, E321, E322, E323, E330, E332n,

E340, E342n, E350, E360, E450, E460, E462dtn

M series MS310d, MS310dn, MS410d, MS410dn, MS510dn, MS610dn, MS610de, MS710, MS711, MS810,

MS811, MS812, MX310dn, MX410de, MX510de, MX610de, MX611de, MX611dhe, MX710, MX711,

MX810, MX811, MX812

Optra

TM

All

T series T420, T430, T520, T522, T620, T622, T630, T632, T634, T640, T642, T644, T650, T652, T654, T656dne

W series W812, W820, W840, W850

WinWriter

TM

600

4035 5W

X series X203, X204, X215, X264, X363, X364, X422, X463, X464, X466, X500, X502, X543, X544, X546dtn,

X548, X560(n), X642e, X644e, X646e, X651, X652, X654, X656, X658, X734, X736, X738, X746, X748,

X782, X792de, X792dte, X792dtfe, X792dtpe, X792dtme, X792dtse, X850, X852e, X854e, X860e,

X862e, X864e, X925, X940, X945, X950

The information supplied here supersedes other information relating to card stock and labels included with your printer.

See other printer documentation for detailed information about the paper, envelopes, and transparencies suitable for

your printer.

In addition to printer‑specific media recommendations, this document also explains design factors to consider when

purchasing all types of print materials. For definitions of industry terms, see “Glossary” on page 174. If you have specific

stock or design questions, then contact your print materials supplier.

See your printer documentation for general printing information and terms. For technical assistance contact numbers,

see the printer registration card, information on the printer CD, or visit the Lexmark Web site at

http://support.lexmark.com.

Note: Always test print materials thoroughly before buying large quantities. Doing so will help you avoid unexpected

problems when you begin regular printing.

Overview 7

General information

Paper and label industry

The paper and label industry includes manufacturers, converters, and distributors.

• Manufacturers produce the base stock. If the base is for labels, then manufacturers may ship it on large rolls or in

a cut‑sheet form.

• Converters take the base stock and convert it into cut‑sheet products. Converters may work from rolls with or

without the adhesive applied. They may also take a base stock and convert it to meet their customers' specifications.

The conversion process includes, but is not limited to, cutting the stock to size, perforating the stock, die‑cutting,

and applying inks and topcoats. Converters work with their customers to convert the base material into a cut‑sheet

product designed for use in laser printers.

• Distributors are generally the direct link to the customer.

As needs and prices change, distributors may work with different converters and converters may work with different

manufacturers. Most businesses follow accepted industry conventions, but specifications, standards, formulations, and

processes may vary with time or with different companies.

As a result, labels or paper that worked well in the past may suddenly create printing problems because of a change in

material or process.

Some large businesses perform all three functions, from manufacturing to distribution. These companies may offer

greater expertise and product consistency than companies that concentrate on one facet of the process.

Printing volumes

Printing numerous sheets of card stock or labels in a short period of time can create printing problems. Continuous

printing on labels, for example, may result in more frequent service calls. The glue on the labels can be squeezed out

by the rollers in the printer and contaminate other printer parts. Most labels and card stock have cuts or perforations

that can be abrasive if not ironed or flattened.

Special media, in general, have rough coatings and are thicker.

Proper printer maintenance can help you avoid these problems. For information about maintaining your printer, see

“Maintenance procedures” on page 14.

Testing print material

Consider the following factors when choosing print materials:

• Physical characteristics of the base stock and the manufacturing processes, which are dependent on the vendor,

may change over time.

• The quality of print materials can also affect printer reliability and downtime. Using materials from converters or

vendors who are unfamiliar with laser printing may result in unsatisfactory print quality or other printing problems.

Once a design is finalized, test the print material before placing a large order to avoid costly mistakes.

General information 8

Your print materials supplier should be able to help develop your application or solve a problem you have with an

existing application. In addition, Lexmark has worked with several suppliers and has business partners in this field. For

technical assistance contact numbers, see the printer registration card, information on the printer CD, or visit the

Lexmark Web site at

http://support.lexmark.com.

Design factors

Print materials all have measurable characteristics that you need to consider when selecting or designing forms for

your particular application.

Basis weight

Basis weight is a term used to describe the weight in pounds of 500 sheets of paper (one ream). However, the weight

is determined based on the standard size of the paper, which may not be the purchased size. For example, the standard

size of 20‑lb bond paper is 17 x 22 inches, and a ream of 17 x 22‑inch 20‑lb bond paper weighs 20 pounds. If the

17 x 22‑inch 20‑lb bond paper was cut, creating four reams of 8.5 x 11‑inch paper, each ream would be labeled 20‑lb

bond paper but would only weigh five pounds.

If the same paper weighed 24 pounds, it would be called 24‑lb bond. The 24‑lb bond paper is thicker, heavier, and more

dense than the 20‑lb bond. Thicker paper means less paper can be placed in a tray, and paper that is heavier and more

dense may cause paper jams or feed reliability problems in some printers. Check the supported paper weights table

located in the printer documentation to verify that the paper basis weight being used is acceptable.

Not all basis weights are related to the same standard sheet size: for example, 70‑lb material can be lighter than 40‑lb

material if it is based on larger base size paper. The metric measurement of grams per square meter (g/m

2

) is a more

consistent way to compare weights and has been standardized by the International Organization for Standardization

(ISO). For more information, locate your printer in the “Printer specifications” chapter.

Your printer can accept a wide range of stock weights, but materials either too light or too heavy can cause printing

problems. Heavy and/or thicker materials may not heat quickly enough in the fuser, resulting in poor print quality. They

may also feed less reliably or skew due to their weight or rigidity. Conversely, lighter materials can wrinkle and jam in

the printer due to low beam strength (stiffness).

Depending on the orientation of the stock as it feeds through the printer, you may need to request that heavier materials

be cut grain short or grain long to provide flexibility in paper path turns. For more precise recommendations, locate

your printer in the “Printer specifications” chapter.

Dimensions

All printers have print material dimension limitations. See the printer documentation that came with your printer for

details. You can sometimes redesign forms to overcome these limitations. For example, if you use forms that are shorter

than the minimum length supported by your printer, you may be able to link two forms together when printing multiple

forms. An optional Universally Adjustable Tray designed for the Optra S, Optra T, and Lexmark T printer families prints

on a range of paper sizes including A6 and 3 x 5‑inch index cards, 3 x 7‑inch punch cards, and 4 x 6‑inch postcards.

Environment

Lexmark printers meet or exceed all industry emission regulations and standards. Continuous printing on some papers

or other media may create fumes that are not a problem with occasional printing. Make sure your printer is located in

a well‑ventilated area.

Temperature and humidity can have a major impact on printing. Even small changes (such as from day to night) can

greatly affect feed reliability if the print material is just within the range of acceptability.

General information 9

We recommend that you condition stock while it is still in the original wrapper. To condition stock, store it in the same

environment as the printer for 24–48 hours before printing to let the stock stabilize at the new conditions. You may

need to extend this time by several days if the storage or transportation environment is very different from the printer

environment. Thick stock may also require a longer conditioning period because of the mass of the material.

If you remove the wrapper from the stock before you are ready to load it in the printer, the stock may develop uneven

moisture content that can cause curl. Prior to loading your stock, we recommend that curl not exceed 3 mm (0.125 in.).

Lighter materials, such as paper labels and some integrated forms, are more likely to have printing problems if curl is

present.

Most label manufacturers recommend printing in a temperature range of 18–24°C (65–75°F) with relative humidity of

40–60%. Lexmark printers are designed to operate in a temperature range of 15.5–32°C (60 to 90°F) with relative

humidity of 8 to 80%. Printing in an environment outside these recommendations may cause jams, feeding problems,

reduced print quality, and predispensing (peeling) labels.

Inks (preprinted stock)

Preprinted stock introduces semi‑liquid and volatile components to the high temperatures and pressure used in the

laser printing process. Preprinted inks and colorations must withstand a fuser temperature up to 225°C (437°F) and

pressure up to 25 psi without contaminating the printer or creating hazardous fumes.

Thermography inks are not recommended. Thermography inks have a waxy feel and the printed image appears raised

above the surface of the print material. These inks can melt and damage the fuser assembly.

Preprinted inks must also be abrasion resistant to reduce ink dust and ink contamination in the printer. If you are

printing over a preprinted area, the ink must be receptive to toner to ensure adequate fusing.

All preprinted inks must be thoroughly dry before using printed materials. However, we do not recommend using offset

powders or other foreign materials to speed drying. Check with your converter, or the manufacturer or vendor of the

ink you plan to use, to determine if the ink is compatible with laser printers that heat the ink to 225°C (437°F).

Perforations and die‑cuts

If your form has perforations, the perforation line should stop 1.6 mm (0.06 in.) from each edge of the form to avoid

separating the form in the printer path, resulting in a jam. The location of the perforation affects initial pick strength.

Perforations closer to the edge may increase the number of jams. For pressure‑sensitive materials such as labels,

minimize the number of perforations that go through the backing material, or liner, since these can also affect the

strength of the form.

Perforations should be ironed so the print material lies flat, reducing nesting of forms. Edges should be smooth and

clean with no roll‑over. Laser

‑

perfs (also known as micro

‑

perfs or data

‑

perfs) provide greater stability and are preferred.

These smaller perforations do not normally nest or create excessive paper dust and debris. Make sure paper chaff and

dust created during the conversion process are removed before packaging.

If perforations tent, or crease at the perforation line, the perfs may break, causing a paper jam. Tenting may increase

skew, cause double‑sheet feeding, or smear the toner on the print material before fusing, resulting in poor print quality.

To reduce tenting, use micro‑perfs. If the print material is lightly snapped as it moves through the printer, the

perforations should hold without breaking.

Die

‑

cutting is used to create shapes in a label or a card stock design. When designing labels, round all corners to prevent

delamination of the labels, and avoid cuts through the liner (anvil cuts). Back splits and pop‑out windows are also not

recommended.

If perforations or die‑cuts are part of the design of the print material, ties are recommended. These small uncut areas

(approximately 1.6 mm or 0.06 in.) help stabilize the form and prevent tearing at perforations and die‑cuts during

printing.

General information 10

For areas with die‑cuts or perforations that create a small end product, or where die‑cuts or perforations intersect, ties

on the corners of the design provide added stability. Ties may be located anywhere along perforations or die‑cuts. For

pressure‑sensitive products, ties help prevent the labels from peeling off the liner while in the printer. Ties cannot,

however, be used to compensate for inadequate release strength of the adhesive in label designs.

For specific perforation and die‑cut guidelines for your printer, locate your printer in the “Printer specifications” chapter.

Debossing and embossing

Avoid debossing and embossing materials. Embossing leads to nesting and double‑sheet feeds, and the fusing process

significantly reduces the height of the raised image. Printing too close to embossments results in poor print quality and

poor fuse grade.

Metallics

We do not recommend using metallics in forms, whether in inks or other materials, due to their conductivity and their

ability to bleed charge. This can interfere with toner transfer and cause poor print quality.

Basic form design

When designing forms, include a non‑print area of 8.38 mm (0.33 in.) at the top and bottom of the form and 6.35 mm

(0.25 in.) on both sides of the form.

In general, portrait orientation is the preferred layout, especially if you are printing bar codes. If your forms require

landscape orientation, be aware that variations in paper path speed may produce spacing variations when printing bar

codes.

Note: We do not warrant uninterrupted or error‑free operation of a product. Warranty service does not include

repair of failures caused by:

• modification or attachments

• accidents or misuse

• unsuitable physical or operating environment

• maintenance by any unauthorized (non‑Lexmark) servicer

• operation of a product beyond the limit of its duty cycle

• failure to have installed a maintenance kit as specified (if applicable)

• use of printing media outside of Lexmark specifications

• use of non‑Lexmark supplies (such as toner cartridges and/or inkjet cartridges)

• use of non‑Lexmark product or component

Pick roller technology

Some printers have an auto compensator which feeds paper more reliably than the corner buckler system used by

earlier printer models. The auto compensator has two rollers that touch the media. Avoid placing deep perforations in

these areas since the media may nest, causing multiple sheets to feed. Perforations that could cause nesting and tenting

should fall outside the pick roller area on the leading edge of the media. This is different from the 0.50‑inch space we

recommend leaving at the top of the form for printers with a corner buckler system. You may want to use micro‑perfs

to avoid nesting problems. For more information, see “Perforations and die‑cuts” on page 10.

General information 11

For the following printers, make sure perforations fall outside the 0.3–0.79‑inch area on the leading edge of the media:

Optra S, Optra T, T520, T522, T620, T622, T630, T632, T634, T640, T642, T644, T650, T652, T654, T656dne, X203, X204,

X264, X363, X364, X463, X464, X466, X543, X544, X546dtn, X560n, X642e, X644e, X646e, X651, X652, X654, X656, X658,

X734, X736, X738.

General information 12

For the following printers, make sure perforations fall outside the 0.31–1.05‑inch area on the leading edge of the media:

C520, C522, C524, C530, C532, C534, C540, C543, C544, C546dtn, C734, C736, C750, C752, C760, C762, C770, C772,

C780, C782, C792e, C792de, C792dte, C792dhe, CS310n, CS310dn, CS410n, CS410dn, CS510de, CX310n, CX310dn,

CX410e, CX410de, CX410dte, CX510de, CX510dhe, CX510dthe, X792de, X792dte, X792dtfe, X792dtpe, X792dtme, and

X792dtse.

General information 13

For the following printers, make sure perforations fall outside the 0.12–0.91‑inch area on the leading edge of the media:

MS710, MS711, MS810, MS811, MS812, MX710, MX711, MX810, MX811, and MX812.

Pick Roller Location

0.12 in.

0.91 in.

0.56 in.

1.08 in.

2.76 in.

3.28 in.

Direction of Feed

Maintenance procedures

Note: These procedures apply only to mono laser printers.

If print quality begins to degrade when printing on vinyl labels, then do the following:

1 Print on five sheets of paper.

2 Wait approximately five seconds.

3 Print on five more sheets of paper.

To maintain printer feeding reliability, repeat this cleaning process every time you replace the toner cartridge.

Note: Failure to follow maintenance procedures for your printer could cause jams, poor print quality, feeding

problems, and fuser problems.

Troubleshooting

The following table provides solutions to some common card stock and label problems. For more troubleshooting

information, see your printer documentation.

General information 14

Problem Solution

Print on heavy stock is

blurred or out of focus.

Make sure the Paper Type setting is correct for your print material.

Note: Card stock in excess of 203 g/m

2

(54‑lb bond) may not produce acceptable print

results.

Print on five sheets of paper, wait for approximately five seconds, and then print five more

sheets of paper to remove any toner that may have accumulated.

Toner rubs off the page. Make sure the Paper Type setting is correct for your print material.

Use material that is lighter than 300 g/m

2

.

Print on five sheets of paper, wait for approximately five seconds, and then print five more

sheets of paper to remove any toner that may have accumulated.

Printing shows voids. Change the Paper Type to Plain Paper.

Print on five sheets of paper, wait for approximately five seconds, and then print five more

sheets of paper to remove any toner that may have accumulated.

General information 15

Card stock

Card stock is a rigid, stiff material that can have a wide variety of constructions. Orientation of paper fibers (grain

direction), moisture content, thickness, texture, and other properties can significantly impact printing, as can

preprinting, perforation, creasing, and other features common to forms. For example, preprinting introduces

semi‑liquid, volatile components that must withstand the high temperatures used in laser printing. Perforation and

creasing may cause nesting, or interlocking, which can cause paper jams and double-sheet feeds.

In general, we recommend a single‑ply construction of 100% chemically‑pulped wood with a vellum finish. Before

purchasing large quantities of card stock, make sure you test samples of the print material in your printer.

Weight

The weight of card stock significantly affects the print quality and feed reliability of the stock. Specify the correct basis

weight of a stock. For more information, see “Basis weight” on page 9.

Basis weight is the weight in pounds of one ream, or 500 sheets, of paper. Since the sheet size varies from one type of

stock to another, basis weights are not always easily comparable. For example, an office supply store has 8.5 x 11‑size

cover stock (80 lb Bristol) and 8.5 x 11‑size card stock (90 lb Index) side by side on the shelf. Both papers are manufactured

by the same company, and a basis weight comparison indicates the card stock (90 lb Index) is heavier than the cover

stock (80 lb Bristol). In this case, however, the cover stock (80 lb Bristol) is actually heavier than the card stock (90 lb

Index).

Before the two types of paper were cut into 8.5 x 11‑size pages, the card stock was a larger sheet size than the sheet

size of the cover stock. When the papers were cut during the manufacturing process into 8.5 x 11‑size pages, more

reams (500 sheets) of paper were received from the card stock sheets than from the cover stock sheets. This makes

the weight of the cover stock heavier than the weight of the card stock.

It is easier to compare the cover stock metric weight (g/m

2

) against card stock metric weight (g/m

2

). If you look at the

metric weights of the two stocks in the previous example, it is immediately evident that 80 lb Bristol cover stock

(176 g/m

2

) is heavier than 90 lb Index card stock (163 g/m

2

).

Not all printers are able to print on cover stock. This is because cover stock is usually thicker and not able to make the

turns in the printer paper path. This causes paper jams and sometimes causes the paper to feed incorrectly. Also, when

using a laser printer, toner is pulled onto the paper through an electrical charge. If the paper is too thick, then there

may not be enough voltage to pull the toner onto the paper properly, resulting in poor print quality.

To determine if your printer supports cover stock, see the section for your printer in the "Printer specifications" chapter

and review the supported paper type information. You can also view the supported paper types in the documentation

that came with your printer.

Use the following table to compare the weights of various types of card stock.

Card stock 16

Card stock weights comparison

Metric

equivalent

(g/m

2

)

Basis weight (lbs/ream)

Bond

431.8 x

558.8 mm

(17 x 22 in.)

Offset

635 x

965.2 mm

(25 x 38 in.)

Cover

508 x

660.4 mm

(20 x 26 in.)

Printing Bristol

571.5 x 889 mm

(22.5 x 35 in.)

Index Bristol

647.7 x 774.7 mm

(25.5 x 30.5 in.)

Tag

609.6 x

914.4 mm

(24 x 36 in.)

75 20 50 — — — 50

90 24 60 — — — —

105 28 70 — — — —

108 29 — 40 — — —

118 31 80 — — — —

120 32 — — — 67 74

131 35 90 — — — —

135 36 — 50 — — —

148 39 100 — — — —

163 43 — 60 — 90 100

176 47 120 65 — — —

199 53 — — 110 110 —

203 54 — — — — 125

Card stock weights may vary ± 5%.

Depending on the printer, material thicker than 0.30 mm (0.012 in.) may present feed reliability problems, and material

thicker than 0.17 mm (0.007 in.) may reduce print quality. Contact your supplier to determine the weight of any card

stock you currently use.

See the individual printer specifications in this document for more information about the card stock weights your printer

supports.

Grain orientation

Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain short, running the width of

the paper, or grain long, running the length of the paper.

The orientation of the grain contributes to the rigidity of card stock and affects feed reliability. The recommended grain

orientation depends on the weight of the stock and whether the printer feeds the stock short edge first or long edge

first. For lighter card stocks, grain long is recommended to reduce potential curl problems. Curl may decrease the ability

of the form to move reliably through the printer.

Most printers feed paper short edge first. If your printer supports larger paper sizes, such as 11 x 17 in. or A3, it may

feed some paper sizes long edge first. See your printer documentation for more information.

For materials fed short edge first:

Card stock 17

Grain short is recommended for stock heavier than 135 g/m

2

Feed

directio

n

Grain

direction

Grain long is recommended for stock lighter than 135 g/m

2

Feed

directio

n

Grain

direction

For materials fed long edge first:

Grain long is recommended for stock heavier than 135 g/m

2

Feed

direction

Grain

direction

Grain short is recommended for stock lighter than 135 g/m

2

Feed

direction

Grain

direction

See the individual printer specifications in “Printer specifications” on page 32 for more information about the

recommended grain direction for card stock you use with your printer.

Coatings

Surface texture and coatings on card stock significantly affect toner adhesion (fuse grade), print quality, and feed

reliability. We recommend a vellum finish for the best printing performance. We do not recommend glossy coatings

and slick surfaces or surfaces that mimic laid finishes (glossy paper, not glossy card stock, is acceptable for some printers).

Paper smoothness also affects print quality. If the paper is too rough, the toner does not fuse to the paper properly; if

the paper is too smooth, it can affect feed reliability. We recommend smoothness to be between 100 and 400 Sheffield

points (150–250 is optimal). Using media higher than 300 Sheffield could result in printing degradation.

Card stock 18

Offset powders

We do not recommend using offset powders or other foreign materials to speed drying. Offset powders are used by

print shops to prevent printed pages from sticking together. Powder is usually sprayed on the printed page right before

it reaches the stacker on the offset printing press. This powder provides an intermediate layer between two sheets of

paper, preventing ink from transferring from one sheet to another.

Card stock 19

Labels

Labels , or pressure‑sensitive materials, are multi‑ply materials that contain various combinations of face sheets

(printable stock), adhesives, and removable protective backings (liners). These layers can result in thick materials that

are difficult to handle.

Labels are among the most difficult print materials for any printer to reliably feed and print. Factors such as heat,

pressure, and paper path could make printing on labels quite challenging. For example, temperatures near 225°C (437°F)

[temperatures vary between printers; check the section for your specific printer] and pressures to 25 psi can be

necessary for the fusing process. Heavy label stock can absorb heat, which in turn affects toner adhesion and print

quality and causes problems such as delamination.

Note: To prevent labels from peeling off or delaminating, make sure the release strength of the labels is sufficient to

withstand the temperature and pressure extremes generated during printing.

Label characteristics

The materials used to construct labels have a wide range of properties that can affect printing. Volatile components

are in the label materials and in the adhesive itself. We recommend that volatile emissions from the label, up to 160°C

(320°F), should be a minimal amount. The volatile components, which have low boiling point, produce emissions when

heated in the fuser and could emit vapors that can damage the printer.

Preprinted inks can also cause printer contamination, and may be present on one or both sides of the label sheet.

Follow the recommended label design guidelines to prevent labels from peeling off, which could cause jams. The label

or adhesive could also melt if the sheet is jammed in the fuser.

Review label designs with a converter or a vendor who has extensive knowledge about labels and laser printers to

ensure that you are using the proper type of labels.

Before purchasing large quantities of labels, make sure you extensively test the labels with your printer.

Printing on labels

Print on full label sheets only. Sheets with missing labels could peel off during printing and result in a paper jam. Partial

sheets can also leave adhesive marks on the printer and cartridge, which could void the printer and cartridge service

warranties.

Do not feed labels through the printer more than once. Doing so may contaminate the cartridge and other components

with adhesive.

Depending on your printer model and the number of labels being printed, printing labels may require special printer

maintenance. For specific maintenance information, see the documentation that came with your printer.

For more information about printing on labels, see the section for your printer in the “Printer specifications” chapter.

Duplexing paper labels

Labels are not typically duplexed because of their special construction. However, printing on both sides of the label

sheet may be possible if certain design, construction, and usage guidelines are followed.

Labels 20

Page is loading ...

Lexmark C910 Finisher Compatibility Manual

Lexmark C910 Finisher Compatibility Manual

Related papers

Other documents