Yukon RANGER 28041 Operating instructions

Brand: Yukon

Model: RANGER 28041

Category: Drive recorders

Type: Operating instructions

OPERATING MANUAL

Please read this manual before using your RANGER.

RANGER is equipped with a built-in, high power IR-illuminator that has a gradual IR adjustment and

memory controller, which provides effective viewing in most night conditions. The unit can be

attached to a standard tripod that uses a 1/4 inch mounting thread. RANGER has a built-in video-out

connector which can be used to pair the device with a monitor or to record video via a recording

device (such as a video camera). For the best image quality, it is recommended to set up the unit on a

tripod before attaching the video cables and recording devices.

The unit is equipped with a special connector that allows RANGER to be powered by a 12 volt car

outlet. It operates for up to 10 hours using 6 AA batteries. The RANGER has an ergonomically-

designed, water resistant, durable plastic body that helps protect the unit and creates versatility.

Yukon's RANGER is ideal for the following applications:

• Surveillance

• Hunting & camping

• Sports and night navigation and observation

• Commercial and personal fishing and boating

• Rescue, recovery, security and law enforcement

• Surveillance and video recording in continuously changing light conditions from dawn to

absolute darkness

BATTERY INSTALLATION

1. Remove the battery compartment cover (1).

2. Pull out the battery container (3) using the attached strap (2).

3. Slide batteries into the battery container (3). Pay attention to «+» (positive) and «-» (negative) symbols

marked on the walls of the container.

4. Insert the battery container (3) back into the battery compartment. Make sure the battery container is

re-inserted properly particularly watching for the orientation of the battery container contacts.

5. Return the battery compartment cover (1) to its original position.

Attention! It is strongly recommended to use only SINGLE-TYPE batteries otherwise the

device's operating time drastically decreases.

OPERATING INSTRUCTIONS

1. Remove the lens caps from the objective lens (4) and from the long-range IR-illuminator (5).

2. Press the button marked «ON» (6) to turn on the device. A stable green light indicates that the device

is ready for use. A flashing green light indicates that the battery power level is low. A flashing red light

indicates that the battery is empty.

3. Locate an object within 20 to 30 meters.

4. Adjust the sensitivity of the device (visually it is determined as image brightness) by turning the

adjustment wheel (11).

5. Rotate the eyepiece's lever (7) and the objective (4) until you see a sharp image. When you turn the

device on, the auxiliary short-range IR-illuminator is turned on automatically. Press the «IR» button (8)

to turn the main IR-illuminator on. Choose the operation modes of the IR-illuminator: press and hold

the «+» (9) or «-» (10) buttons to increase or decrease respectively the power of the IR-illuminator. The

use of the IR-illuminator in the optimal mode prolongs operating time. If the device is focused on an

object closer than 15 metres, the emission spot of the main IR-illuminator (bright light circle) will be

shifted to the right side of the display.

6. When changing the viewing distance, try to see a sharp and high-quality image by rotating the

objective (4) and the sensitivity adjustment wheel (11) and by changing the operating modes of the IR-

illuminator. Do not rotate the eyepiece's lever (7) the device is already individually adjusted.

7. Plug the output video cable into the RANGER's video-output jack (12) to transmit the observed

image to an external LCD monitor. When the RANGER is coupled with video equipment, the

observed image can be recorded.

8. To connect the RANGER to a vehicle's 12V auxiliary power port, plug the car adapter into the

RANGER's power input jack (13) and connect the other end of the cable to the vehicle's auxiliary

power port.

9. To connect the RANGER to a household outlet, use a variable power switching adapter.

Be careful, observe the polarity shown on the inner side of the battery cover.

NOTE. When the batteries are in the container and the external power source is turned on, the

device operates on the external power source. If you unplug the external power source, you

have to press the «ON» button to make the device operate on the batteries.

CARE AND STORAGE

• Do not subject the digital NV device to shock or impact. Do not drop.

• Turn off the device when not in use and when moving the unit.

• The device can be used in daylight as well as nighttime conditions.

• After using the device in cold temperatures, please, wait up to 5 hours before using the device

in the warm temperatures. This helps prevent condensation on the lenses.

• Do not leave the device in direct sunlight or rain.

• Water, sand, dust, and salt can damage the device.

• Do not cover the vent grid (14) of the IR-illuminator. Please keep the grid clean to insure

proper performance of the IR illuminator.

• The device can be powered with 6 nickel cadmium batteries as well as 6 AA batteries.

• The power level of the main and auxiliary IR-illuminators when turning the device on with the

«ON» button (6) and switching the IR-illuminators with the «IR» button (8) corresponds to the

value previously set with the «+» (9) or «-» (10) buttons.

• Do not connect stray devices (headphones, for example) to the «Video» port. This may put the

device out of action.

• When focusing on the display (you can see the fine black net) 7 light or dark spots on the

whole field of view in the image plane are acceptable.

• The main IR-illuminator can not be focused.

CLEANING

• Do not scratch the external lens surfaces or touch them with your fingers.

• Clean the device's lenses with optic/camera lens tissue or a clean cloth moistened with alcohol.

You may use your breath to mist the surface of the glass prior to wiping. Clean the device's

surfaces with alcohol if necessary and dry thoroughly.

• The RANGER's plastic surfaces do not require special treatment. If necessary, clean the unit's

surfaces with a clean, soft cloth and a petroleum-based jelly and dry thoroughly.

Important Note

Do not pour alcohol directly on the lenses.

Do not clean lenses and unit surfaces with any paper, such as newspaper, notebook paper, etc.: this can

damage the coating.

STORAGE

• Remove the unit's batteries if the device will not be used for longer than 2 months.

• Always store the RANGER in its case.

• Always store the RANGER in a dry, well-ventilated area away from heating/air conditioning

vents and other heating devices. Temperature should be greater than +50F (+10oC), and

humidity should not exceed 70%.

TROUBLESHOOTING

The Table lists possible problems that you may encounter with your equipment. If the equipment

problem is not listed or the corrective actions listed do not correct the issue, notify the manufacturer.

PROBLEM TEST OF INSPECTION CORRECTIVE ACTION

1. Monocular fails to activate

Visual

Check for defective, missing or

improperly installed batteries or the

battery container.

Turn unit OFF and then ON

Replace or install batteries or

the battery container correctly.

2. IR Illuminator fails to

activate

The «-» button (10) is in its extreme

position.

The sensitivity adjustment wheel

(11) is in its extreme position.

Press the «+» (9) button and

hold for 5-8 seconds.

Adjust sensitivity of the device.

3. Poor image quality

Check the objective lens and

eyepiece, making sure they are

focused according to the

instructions listed in section:

OPERATING INSTRUCTIONS.

Check for fog or dirt on the lens.

Follow the instructions to

adjust the device.

4. There are several light or

black dots (pixels) on the

display of the device.

Presence of dots is caused by

matrix production technology and

is not a defect.

No action needed.

Yukon RANGER 28041 Operating instructions

Brand: Yukon

Model: RANGER 28041

Category: Drive recorders

Type: Operating instructions

Download PDF

report

Yukon RANGER 28041 Operating instructions

Yukon RANGER 28041 Operating instructions

Related papers

Other documents