KRAUS KEF-15301CH Installation guide

Brand
KRAUS
Model
KEF-15301CH
Category
Car kits
Type
Installation guide
INSTALLATION MANUAL
Aplos™ Single Handle Basin
Bathroom Faucet
KEF-15301
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. August 16, 2016
2
Thank you for your purchase
We would like to take this opportunity to thank you for choosing Kraus.
We hope that you are completely satised with your purchase, and enjoy it for years
to come. If you have any questions, or require technical assistance, please contact
us at 800.775.0703 and one of our representatives will be happy to help.
For more information about Kraus products, please visit:
www.kraususa.com
In order to activate your warranty and get faster access to customer support, please
register your new Kraus product at:
www.kraususa.com/registration
Sincerely,
Kraus USA Customer Service
3
PRIOR TO INSTALLATION
• Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing of damaged, please contact Kraus Customer Service at 800-
775-0703 for a replacement.
• Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
• Place a bucket under angle stops. Turn on to ush any debris prior to installing
new plumbing. Shut o angle stops
• Pre-drilled hole size requirement: 1-3/8” (min) – 1-1/2” (max)
• Max countertop thickness: 1-3/4”
Tools you will need:
Adjustable Wrench Phillips Screwdriver
Safety Goggles Bucket
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7
º
(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅
1 3/4”
(
∅
45mm)
∅
1 15/16”
(
∅
50mm)
9/16”-18UNEF
27mm ~ 41.3mm
1 1/16” ~ 1 5/8”
∅
1 15/16”
(
∅
50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
4
A
F
E
D
C4
C3
C2
C1
B
Diagram and Parts List
A. Faucet Body
B. Waterlines
C. Mounting Hardware Assembly
C1. Rubber O-Washer
C2. Metal O-Washer
C3. Mounting Nut
C4. Mounting Screw
D. Drain
E. Aerator
F. Aerator Key
5
max30
(1-1/8”)
Ø35mm
(1-3/8”)
(5-3/4")
96mm
146mm
(3-3/4”)
120mm
(4-3/4”)
(2-1/4”)
58mm
G1/2
Faucet Dimensions
6
Step1: Remove mounting hardware
Remove mounting hardware
assembly (C)
Step 2: Install hot & cold waterlines
Step5
Step4
C1
C2
C3
C4
16
17
18
13
6
Step 2 Step 3
Install waterlines (B)
• Hot Side: Left
• Cold Side: Right
Installer Tip: HAND TIGHTEN
ONLY
B
Step 3: Install faucet
Step 3
Step6
C1
C2
C3
C4
9
10
8A
8B
8C
8D
Place faucet body (A) through
1-3/8” hole in countertop. Attach
mounting hardware assembly (C)
and secure
A
7
Step1: Remove mounting hardware
Remove mounting hardware
assembly (C)
Step 2: Install hot & cold waterlines
Step5
Step4
C1
C2
C3
C4
16
17
18
13
6
Step 2 Step 3
Install waterlines (B)
• Hot Side: Left
• Cold Side: Right
Installer Tip: HAND TIGHTEN
ONLY
B
Step 3: Install faucet
Step 3
Step6
C1
C2
C3
C4
9
10
8A
8B
8C
8D
Place faucet body (A) through
1-3/8” hole in countertop. Attach
mounting hardware assembly (C)
and secure
A
8
Step 4: Install drain
1. Remove waste stopper (d) from drain (e). Remove drain body (j),
mounting nut (i), plastic washer (h), and concave washer (g) from
drain (e)
2. Insert lift pole rod (a) through the hole in the back of the faucet body
(A). Attach lift pole extension (c) to lift pole rod (a) by using connector
(b). Secure tightly
3. Install drain (e), with rubber washer (f) attached, into the drain hole.
From underneath countertop, attach concave washer (g), plastic
washer (h), and mounting nut (i) to drain (e), and secure tightly to
sink. Thread drain body (j) onto drain (e). Hand-tighten
4. Insert waste stopper (d) into drain (e). Make sure hole in brass screw
on waste stopper (d) is aligned with drain body (j) opening
5. Remove retaining nut (o) from drain body (j). Leave top hat washer
(m) inside drain body (j)
6.
retaining nut (o) to drain body (j)
7.
(c) to engage
8.
connector (l). Adjust and tighten elbow connector (l) with Phillips
head screwdriver
Insert shortest end of drain-o-pole (k) into drain body (j). Attach
washer (n) and retaining nut (o) through drain-o pole (k). Secure
Align drain body (j) to enable drain-o pole (k) and lift pole extension
Connect lift pole extension (c) and drain-o pole (k) using elbow
Step 4: (Continued)
Step4
d
e
f
c
b
a
A
g
h
i
p
j
m
n
o
l
k
9
Step 4: Install drain
1. Remove waste stopper (d) from drain (e). Remove drain body (j),
mounting nut (i), plastic washer (h), and concave washer (g) from
drain (e)
2. Insert lift pole rod (a) through the hole in the back of the faucet body
(A). Attach lift pole extension (c) to lift pole rod (a) by using connector
(b). Secure tightly
3. Install drain (e), with rubber washer (f) attached, into the drain hole.
From underneath countertop, attach concave washer (g), plastic
washer (h), and mounting nut (i) to drain (e), and secure tightly to
sink. Thread drain body (j) onto drain (e). Hand-tighten
4. Insert waste stopper (d) into drain (e). Make sure hole in brass screw
on waste stopper (d) is aligned with drain body (j) opening
5. Remove retaining nut (o) from drain body (j). Leave top hat washer
(m) inside drain body (j)
6.
retaining nut (o) to drain body (j)
7.
(c) to engage
8.
connector (l). Adjust and tighten elbow connector (l) with Phillips
head screwdriver
Insert shortest end of drain-o-pole (k) into drain body (j). Attach
washer (n) and retaining nut (o) through drain-o pole (k). Secure
Align drain body (j) to enable drain-o pole (k) and lift pole extension
Connect lift pole extension (c) and drain-o pole (k) using elbow
Step 4: (Continued)
d
e
f
c
b
a
A
g
h
i
p
j
m
n
o
l
k
10
Step 6: Flush faucet
Step 5: Connect waterlines to main valve
Step5
Step6
Step6
8A
8B
8C
8D
9
10
Attach waterlines (C) to angle
stops and tighten until snug. Turn
on angle stops and check for leaks
Installer Tip: Make sure grid
(DO NOT TURN FAUCET ON)
of waterlines prior to installing
washer is installed at the end
C
* Grid Washer
Turn faucet on for one minute to
check ow
11
Step 6: Flush faucet
Step 5: Connect waterlines to main valve
Step5
Step6
Step6
8A
8B
8C
8D
9
10
Attach waterlines (C) to angle
stops and tighten until snug. Turn
on angle stops and check for leaks
Installer Tip: Make sure grid
(DO NOT TURN FAUCET ON)
of waterlines prior to installing
washer is installed at the end
C
* Grid Washer
Turn faucet on for one minute to
check ow
Replacement Part List - KEF-15301
12
13
14
7
8
9
10
11
15
1B 1A
2
3
4
5
6
1. A. Cap
B. Set Screw
2. Handle Cap
3. Cartridge Cover
4. Locking Nut
5. O-Ring
6. Cartridge
7. Base O-Ring
8. Rubber O-Washer
9. Metal O-Washer
10. Mounting Nut
11. Mounting Screws
12. Aerator
13. Aerator Key
14. Waterlines
15. Drain
16. Hex Wrench
12
Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PROBLEM CAUSE ACTION
Leakage under the handle Locking nut (4) has
come loose
Remove cap (1a). Loosen
set screw (1b) with hex
wrench (16). Remove
metal handle (2). Unscrew
cartridge cover (3) (by
hand only). Tighten
locking nut (4) with an
adjustable wrench
Aerator (12) drips or has
inconsistent water flow
pattern
Aerator (12) is dirty or not
seated properly
Unscrew aerator (12) with
aerator key (13) and clean
out debris
Drain (15) is leaking Washers may be
compromised or installed
incorrectly
Check washers to make
sure they are installed
correctly and not cracked
Water will not shut off
completely
Cartridge (6) may need to
be adjusted or replaced
Remove cap (1a). Loosen
set screw (1b) with hex
wrench. Remove metal
handle (2). Unscrew
cartridge cover (3) (by
hand only). Unscrew
the locking nut (4) with
an adjustable wrench.
Remove ceramic disc
cartridge (6). Check for
cracks
13
Codes/Standards Applicable:
NSF/ANSI 372
NSF/ANSI 61
ASME A112.18.1M
1.2GPM 4.5L/min maximum
GREEN
Water Eciency
LEAD FREE
I
A
P
M
O
R
&
T
TM
HELP LINE
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
[email protected]
If you are a plumbing contractor or trade professional please contact a Kraus Pro
Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
[email protected]
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
Partnersupport@kraususa.com
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
14
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
2
3
10
9
11
12
13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
4
5
7
6
8
4
5
6
7
8
Ø1 3/8”~
Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10
11
Close
Open
Left
Hot Water
Push
25˚
90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12
13
2
3
4
5
6
7
8
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
15
www.kraususa.com
Receive Proof of Ownership
Access Customer Care & Installation Help
Get Exclusive Kraus Oers & Promotions
Scan to Register Online
or visit http://www.kraususa.com/registration
Please take a moment to share your experience.
Visit http://www.kraususa.com/review to let us know what you think
about your new Kraus product.
Contact Us to Learn More
1.800.775.0703 / www.kraususa.com / [email protected]
Like & Follow KrausUSA
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
www.kraususa.com
REGISTER YOUR PRODUCT TODAY
We’re always looking for ways to improve.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

KRAUS KEF-15301CH Installation guide

Brand
KRAUS
Model
KEF-15301CH
Category
Car kits
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents