CONCORD PROTON is a versatile and safe baby carrier that can be used for newborns and infants up to 10 kg. It features a 4-position adjustable carrying handle, a backrest that can be adjusted to a flat position for use in a car, and a removable sunshade with ventilation. The carrier can be securely attached to compatible CONCORD buggy frames using the included adaptors. For use in a car, the carrier must be secured with the vehicle's safety belt and the backrest must be in the lowest position.
CONCORD PROTON is a versatile and safe baby carrier that can be used for newborns and infants up to 10 kg. It features a 4-position adjustable carrying handle, a backrest that can be adjusted to a flat position for use in a car, and a removable sunshade with ventilation. The carrier can be securely attached to compatible CONCORD buggy frames using the included adaptors. For use in a car, the carrier must be secured with the vehicle's safety belt and the backrest must be in the lowest position.
28
29
Veränderungen oder Verschlechterungen des Produkts, die durch den
vertragsmäßigen Gebrauch herbeigeführt werden (Abnutzung) sind kein
Garantiefall. Durch Leistungen des Herstellers im Garantiefall wird die Garantie
nicht verlängert.
_ ENGLISH
FEATURES 30
THANK YOU! 32
NOTES 33
ADJUSTING THE CARRYING HANDLE 36
ADJUSTING THE BACKREST 38
SECURING ON THE FRAME OF A CONCORD BUGGY 40
USE IN A CAR 42
USING THE SUNSHADE 48
VENTILATION 49
CARE AND MAINTENANCE 50
GENERAL INFORMATION 51
WARRANTY 52
29
30
31
_ FEATURES
01 Adjustment lever
02 Release button
03 Sunshade
04 Carrying handle
06 Receiver for
belt adaptor
07 Rotary knob
09 Zip for securing
the sunshade
08 Zip for sun shade
ventilation
05 Safety belt
10 Cover with
zip and pocket
11 Belt adaptor
12 Buggy adaptor
13 Ventilation lever
32
33
_ NOTES
IMPORTANT
• Please read the instructions for use thoroughly before using the CONCORD
PROTON and keep them carefully for later reference.
• Never leave the child unattended.
• Only one child at a time should be laid in the CONCORD PROTON baby
carrier.
• The CONCORD PROTON baby carrier is suitable for children with a
maximum body weight of 10 kg.
• Only use the CONCORD PROTON baby carrier together with compatible
buggy frames made by Concord (equipped with the ProFix system).
• Always use the safety belt when the child is lying in the CONCORD
PROTON baby carrier. Check before each car journey that the safety belt is
_ THANK YOU!
We are delighted that you have chosen a quality Concord product.
You are sure to be convinced by this product‘s versatility and safety. We hope
you enjoy using your new CONCORD PROTON.
34
35
correctly positioned and is sufficiently taut.
• Use only original Concord restraint system components. The use of
accessories that are not authorised by the manufacturer can seriously
compromise the child’s safety.
• Any modification you make to the baby carrier or its belt system can
seriously impair the safety of the product and must therefore be avoided.
• Ensure before each journey that any items of luggage or other articles
that could cause injury to passengers in the event of emergency braking are
adequately secured or stowed away.
• The CONCORD PROTON baby carrier must always be secured using the
vehicle safety belt, even if there is no child in it. In the event of emergency
braking, the unsecured carrier could cause injury to persons inside the
vehicle.
• Never hold the child in your arms when travelling or seat it outside the baby
carrier. Even if the vehicle is only travelling at 40 km/h, the child can easily
be catapulted forwards in the event of emergency braking.
• After an accident it is possible that the CONCORD PROTON baby carrier
might be damaged; we recommend that it should always be replaced with
a new one.
• Dispose of the plastic packaging immediately. It can endanger the lives of
children.
Not following the instructions described here can impair the child’s safety.
36
37
_ ADJUSTING THE CARRYING HANDLE
The carrying handle (04) on the CONCORD PROTON baby carrier can be
adjusted to four positions. To adjust the carrying handle, pull the lever (01)
on the baby carrier handle. Now move the carrying handle in the required
direction until it clicks into the appropriate position:
• to the front (P1)
• upright for carrying or for transportation in the car (P2)
• to the rear for folding back the sunshade (P3)
• and horizontal at the back (P4). Please note: the handle does not click into
place in this position.
P1P3
P2
P4
38
39
_ ADJUSTING THE BACKREST
The CONCORD PROTON baby carrier has a backrest that can be fluidly
adjusted using the rotary knob (07). You can pull the rotary knob out to make it
easier to turn.
ATTENTION
If you wish to use the baby carrier in its function as a child restraint system in
the car, you must always adjust the backrest to its lowest position (flat).
40
41
_ SECURING ON THE FRAME OF A CONCORD
BUGGY (equipped with the ProFix system)
To secure the CONCORD PROTON baby carrier to a frame, position the baby
carrier such that the child’s head is facing forwards (in the direction of travel)
and insert the adaptors (12) into the receivers provided on the frame so that
they click audibly into position.
To release the baby carrier from its fastenings, press and hold the release
button (02) on the carrying handle and pull the carrier up and away from the
frame.
42
43
_ USE IN A CAR
• Move the backrest on the CONCORD PROTON baby carrier to its lowest
position (flat).
• Adjust the carrying handle to position P2 (vertically upright).
• The baby carrier must only be placed on the rear seat of the car. There are
three ways to install the baby carrier: in the centre, using the diagonal belts
of the two outer seats, or on one of the outer seats using the outer and a
centre diagonal belt. You can only secure the baby carrier with two diagonal
belts running in diametrically opposed directions (such as on the two outer
seats on the car’s rear seat bench). We recommend when installing the
baby carrier on one of the two outer seats that it should be positioned such
that the child’s head is pointing towards the centre of the car and is
therefore as far as possible from the car door.
44
45
• Secure the two diagonal belts
relevant to the seat you have chosen
in their respective belt buckle so that
the belts lie evenly and closed on
the back seat bench.
• Place the baby carrier on the back
seat bench.
• Open the belt adaptor (11) by
pushing the safety catch to the side.
• Pull the diagonal lap belts out until
you can feed them from the bottom
upwards into the belt adaptors.
• Close the side safety catches on the
adaptors again.
• The diagonal belts now run from
above through the closed vehicle
belt buckles, then through the
closed belt adaptors (from bottom
to top) into the bracket on the
vehicle.
46
47
• Now pull the entire restraint system
taut by pulling the diagonal shoulder
belts upwards until the belts are taut
along their entire length.
• The belts must not be twisted or
creased at any point along their
length.
• Lay the child at full length in the
baby carrier and check that it is lying
comfortably. Position the stomach
belt (05) carefully around the child’s
pelvis and waist and tighten it
carefully.
• To release the restraint system,
open the safety catches on the belt
adaptors.
• To remove the belt adaptors from
the baby carrier, pull the plastic
cover out so that you can easily
unhook the belt adaptor.
If you encounter any difficulties, please
contact your specialist dealer. He will
be happy to assist.
48
49
_ USING THE SUNSHADE
The sunshade (03) on the CONCORD PROTON baby carrier can be removed
separately. To do this, simply open the zips (09) on the left and right of the
carrying handle. For improved ventilation you can open the zip (08) in the back
of the sunshade.
_ VENTILATION
You will find a lever (13) on the bottom of the baby carrier with which to open
and close the ventilation slots in the base of the carrier.
50
51
_ CARE AND MAINTENANCE
Clean plastic parts with lukewarm water and washing up liquid and then dry
them carefully.
The cover may be removed and washed at a max. temperature of 30° C,
preferably by hand. Then leave the cover to air dry in a shady place. The seat
cover should not be given prolonged exposure to sunlight as this could impair
the fabric colour.
_ GENERAL INFORMATION
• This is a “universal“ child restraint system. It has been tested and approved
pursuant to ECE Regulation 44, Amendment series 03 for general use in
vehicles and will fit in most, but not all cars.
• It may be assumed that the system has been fitted correctly if the vehicle
manufacturer states in the owner’s handbook that the vehicle is suitable for
fitting a “universal“ child restraint system for the relevant age group.
• This restraint system has been classified pursuant to stricter conditions of
the “universal“ class than previous models which do not bear this label.
• If you have any doubts at all, please ask the manufacturer of the child
restraint system or your retailer.
• Only suitable for vehicles with three-point seat belts, which have been
tested and approved pursuant to ECE Regulation 16 or an equivalent
standard.
52
53
_ WARRANTY
The warranty period shall commence at the time of purchase. The warranty
period shall correspond to the duration of the applicable statutory warranty
period for the sale of child seats in the respective end user country.
Depending on the wishes of the manufacturer, the warranty shall cover
rectification, replacement or a price reduction.
The warranty is only valid for the initial purchaser. Should a defect occur,
warranty rights shall only apply if the specialist retailer is notified of the defect
immediately after its initial occurrence. If the specialist retailer cannot solve
the problem, then it must return the product with an exact description of the
problem and official proof of purchase. The manufacturer shall assume no
liability for damage to products which it did not supply.
The warranty shall lapse if:
• the product was altered
• the product is not returned complete with proof of purchase to the retailer
within 14 days of the defect occurring
• the defect occurred due to incorrect operation or maintenance or anything
else deemed to be the fault of the user, or when the user instructions have
not been adhered to
• repairs to the product have been carried out by third parties
• the defect has occurred as the result of an accident
• the serial number has been damaged or removed
Alteration to or deterioration of the product which occurs due to normal wear
and tear is not covered by the warranty. Any corrective action taken by the
manufacturer in response to a warranty claim does not extend the duration of
warranty.
54
55
_ FRANÇAIS
VUE D‘ENSEMBLE 56
TOUS NOS REMERCIEMENTS ! 58
CONSIGNES 59
RÉGLAGE DE L‘ANSE 62
RÉGLAGE DU DOSSIER 64
FIXATION SUR LE CHÂSSIS D‘UNE POUSSETTE CONCORD 66
UTILISATION EN VOITURE 68
UTILISATION DU TOIT OUVRANT 74
AÉRATION 75
MAINTENANCE ET ENTRETIEN 76
GÉNÉRALITÉS 77
GARANTIE 78
55
420
Concord GmbH
Industriestraße 25
95346 Stadtsteinach
Germany
Phone +49 (0)9225.9550-0
Fax +49 (0)9225.9550-55
www.concord.de
_ DEUTSCH
_ ENGLISH
_ FRANÇAIS
_ ESPAÑOL
_ ITALIANO
_ PORTUGUÊS
_ NEDERLANDS
_ MAGYAR
Einbau- und Bedienungsanleitung
Instructions for attachment and use
Directives d‘installation et mode d‘emploi
Instrucciones de montaje y de uso
Istruzioni per l‘uso e il montaggio
Manual de montagem e de utilização
Inbouw- en bedieningshandleiding
Beszerelési és kezelési útmutató
_ ČESKY
_ NORSK
_ DANSK
_ SLOVENSKO
_ POLSKI
_ TÜRKÇE
_ SLOVENSKY
_ HRVATSKI
Návod k montáži a obsluze
Bruksanvisning og monteringsveiledning
Monterings- og betjeningsvejledning
Navodila za vgradnjo in uporabo
Instrukcja montażu i obsługi
Montaj ve Kullanma Kılavuzu
Návod na montáž a obsluhu
Naputak za montažu i uporabu
PR 02/0807
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
CONCORD PROTON is a versatile and safe baby carrier that can be used for newborns and infants up to 10 kg. It features a 4-position adjustable carrying handle, a backrest that can be adjusted to a flat position for use in a car, and a removable sunshade with ventilation. The carrier can be securely attached to compatible CONCORD buggy frames using the included adaptors. For use in a car, the carrier must be secured with the vehicle's safety belt and the backrest must be in the lowest position.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
CONCORD ION User manual
-
-
CONCORD Spin User manual
-
CONCORD air.safe Owner's manual
-
-
-
CONCORD TRANSFORMER T User manual
-
-
CONCORD TRANSFORMER-X-BAG User manual
-
Other documents
-
B&B PIPE & INDUSTRIAL TOOLS PN 2013 Operator's And Safety Manual
-
Chipolino Car seat Archie Operating instructions
-
Mountain Buggy safe rotate Operating instructions
-
Britax High Chair Verve User manual
-
Orbit baby G3 User manual
-
Mountain Buggy Protect Capsule Base Instructions Manual
-
Orbit baby G3 User manual
-
CYBEX Cloud Q User manual
-
kiddy EVO-LUNA I-SIZE Directions For Use Manual
-
Nuna TAVO trvl system User manual
