SciCan HYDRIM L110w G4 User manual

HYDRIM

®

L110w G4

INSTRUMENT WASHER

Operator’s Manual

Manuel de l’utilisateur

Table of Contents

1. Introduction ......................1

2. Important Information ..............2

3. Disclaimers ......................3

4. Installation Instructions.............4

5. Instructions for Use ...............9

5.1 Instrument Reprocessing

Recommendations ..................9

5.2 Cycle Description Chart .............10

5.3 Hints and tips for best cleaning results . 11

5.4 Recommended load congurations ....12

5.5 Baskets and Accessories............14

5.6 Touchscreen Overview .............15

5.7 Set up menu overview ..............16

5.8 - 5.22 Setup menu options ...........17

5.23 Connecting to a network ............22

5.24 Connecting to a wireless network .....22

5.25 Activating the HYDRIM L110w G4.....23

5.26 Interrupting / aborting a cycle ........24

5.27 Additional user

and setup menu functions ...........25

5.28 Opening the Door in

Case of Power Failure ..............26

5.29 Storing and Retrieving

Cycle Information ..................27

5.30 Printer / Data Logger Setup ..........29

6. Care and Maintenance ...........30

6.1 Replacing the HIP™

Cleaning Solution ................. 30

6.2 Relling the Water Softener

Salt Reservoir...................... 32

6.3 Cleaning the HYDRIM L110w G4 .....32

6.4 Filter and Wash Arm Maintenance ....33

6.5 Preparing the unit for shipping .......33

6.6 Annual maintenance ...............34

7. Troubleshooting .................36

8. Specications ..................38

9. Serial Number Plate .............38

10. Warranty ......................39

HYDRIM and STATIM are registered trademarks of SciCan Ltd. BRAVO,

HIP, and SysTM are a trademarks of SciCan Ltd. All other trademarks referred

to in this manual are the property of their respective owners.

For all service and repair inquiries:

In Canada 1-800-870-7777

United States: 1-800-572-1211

Germany:

+49 (0)7561 98343 - 0

International: (416) 446-4500

Email: [email protected]

Manufactured by:

SciCan Ltd.

1440 Don Mills Road,

Toronto ON M3B 3P9

CANADA

Phone: (416) 445-1600

Fax: (416) 445-2727

Toll free: 1-800-667-7733

EU Representative

SciCan GmbH

Wangener Strasse 78

88299 Leutkirch GERMANY

Tel.: +49 (0)7561 98343 - 0

Fax: +49 (0)7561 98343 - 699

SciCan Inc.

701 Technology Drive

Canonsburg, PA 15317 USA

Phone: +1 724 820 1600

Fax: +1 724 820 1479

Toll free: 1-800-572-1211

SciCan Medtech

Alpenstrasse 16

CH-6300 ZUG SWITZERLAND

Phone: +41 (0) 41 727 7027

Fax: +41 (0) 41 727 7029

Thank you for selecting the HYDRIM L110w G4 instrument washer. The HYDRIM

complements the STATIM

®

and BRAVO™ autoclaves by quickly and hygienically

preparing soiled instruments for sterilization. To ensure years of safe, trouble-free service,

carefully review this Operator’s Manual before operating the unit. The HYDRIM L110w G4

is suitable only for the applications listed in this manual. Using the HYDRIM for other

purposes may be dangerous. The manufacturer cannot be held responsible for damage

caused by improper use.

Operational, maintenance and replacement instructions must be followed for the product

to perform as designed. All trademarks referred to in this manual are the property of their

respective owners. Contents of this manual are subject to change without notice to reect

changes and improvements to the HYDRIM product.

The HYDRIM L110w G4 should only be installed and serviced by a qualied contractor

as it is an Installation Category 2 device. Before connecting the unit, the installer should

check that the voltage and frequency of the electrical supply correspond with the details

in the installation instructions. The unit must only be plugged into a grounded outlet.

Please note that this unit is completely isolated from the electrical supply only when it is

unplugged or the circuit breaker is turned OFF. This must be done before any repair work

is carried out.

The HYDRIM L110w G4 uses HIP™ Cleaning Solution exclusively. The unit will not

perform as described if other detergents / cleaning products are used. Other detergents /

cleaning products may damage the unit, the instruments, cause excessive foaming, and

void the warranty. Do not use solvents in this unit. Do not allow small children or

unauthorized personnel access to this unit or its controls.

1. Introduction

1

2. Important Information

The following symbols appear in this book.

Caution, there is a potential hazard to the operator.

This situation may lead to a mechanical failure.

This is important information.

2

Do not permit any person other than authorized personnel to supply parts for service or

maintenance for your HYDRIM. SciCan is not liable for incidental, special or consequential

damages caused by any maintenance or services performed on the HYDRIM by unauthorized

personnel, or for the use of equipment or parts manufactured by a third party, including lost prots,

any commercial loss, economic loss, or loss arising from personal injury.

Never remove any unit panels and never insert objects through holes or openings in the cabinetry.

Doing so may damage the unit and/or pose a hazard to the operator.

If the unit is used in a manner other than that specied, the protection provided by the equipment

may be impaired.

Cleaning solutions may irritate. Avoid contact with eyes, skin and mouth.

Never sit, stand or lean on the open door. The unit may tip forward causing injury.

Always turn the unit OFF before adding softener salt, adding solutions or performing routine

maintenance to the unit.

The owner shall not allow any personnel other than the trained and authorized personnel

to operate the unit.

SciCan recommends leaving the unit turned ON at all times, in particular over times when no staff

is in the ofce or when no water shut-off mechanism is installed. Leaving the unit turned ON will

activate the drain pump if water is leaking into the chamber as a result of any faulty circumstance.

For further information or questions about the HYDRIM L110w G4, contact your authorized dealer.

3. Disclaimers

3

Installation:

Installation should be undertaken by a

SciCan approved technician. The use of

an unapproved installer may invalidate

the warranty.

If the HYDRIM is installed in a Sterilization

Center, the manufacturer of the Sterilization

Center should allow a 10mm / 1/2” space

at the top, back and both sides of the HYDRIM.

This will facilitate installation, and service

access to the HYDRIM.

Do not move the HYDRIM into place by

maneuvering the open wash chamber door.

This may cause to door to become misaligned

and leak.

During installation, all consumables should

have been added to the machine as appropriate.

It is important that this be done before starting

the machine.

4. Installation Instructions

To open the wash chamber door, plug in the unit,

turn it on and press the unlock symbol.

Alternatively, remove the screw in the kickplate

and pull the ring. See section 5.28.

Tools and supplies required for installation:

• Slot screwdriver

• Channel locks

Specications:

Voltage: 208 – 240 V

Frequency: 60 Hz

Rated load: 2.5 kW

Circuit

breaker: 15 A

per phase

Height: 850 mm / 33.5”

Width: 598 mm / 23.54”

Depth: 600 mm / 23.75”

Depth with

door open: 1200 mm / 47”

Weight: 80 kg / 176 lbs

Max. Running Noise: 78 dBA

Utility Hook-ups

For safety reasons, do not install

the HYDRIM without the top cover.

4

Levelling the HYDRIM:

The unit is standing on three supports: rollers (wheels) at the

back and two legs at the front.

1. Remove the front kickplate. Push the HYDRIM

into place while lifting the strap at the front to allow the unit

to roll on the rollers.

2. Adjust the front legs as required until the

HYDRIM is level.

3. The rear two legs are used only if the oor is uneven or

cannot provide support to the rollers.

4. Tuck the strap under the machine before

replacing the kickplate, so as not to interfere

with the exhaust air vents.

RO water

inlet hose

hot water

inlet hose

power

connector

ethernet

connector

printer

connector

drain hose

fuse holder

cold water

inlet hose

Rear of Unit

Hose / Length / Max. Distance Water Shut-off

Cord Diameter Distance from Pressure valve

inlet / drain

Hot Inlet 1.9 m / 6 ft. 1.5 m / 5 ft. 1-10 bar / Yes

3/4” 14.5-145 psi

Cold Inlet 1.9 m / 6 ft. 1.5 m / 5 ft. 1-10 bar / Yes

3/4” 14.5-145 psi

R/O Inlet 1.9 m / 6 ft. 1.5 m / 5 ft. 1-10 bar / Yes

3/4” 14.5-145 psi

Drain 1.5 m / 5 ft. — — —

3/4”

Electrical 1.8 m — — —

AWG 14-3

4. Installation Instructions

Connecting the water inlet hoses:

Connect the hot and cold water inlet hoses to the hot and cold water supply.

Drain requirements:

Connect the drain hose to the drain outlet. The drain hose can be attached to existing drain

lines using a 3.5 cm / 1.5” or larger standpipe / P-trap combination. If the hose is connected

directly to the drain line, ttings and adapters should not reduce water ow. The drain hose

should be attached to the main drain at a point no more than 1 metre /3 ft. above the base of

the HYDRIM. A oor drain is acceptable (check local codes).

Electrical requirements:

Connect the electrical cord to the power supply. The HYDRIM must have a dedicated circuit

equipped with a 15A fuse. The outlet must be grounded.

Additional Information:

• The HYDRIM unit is heavy. Use a forklift or dolly and exercise caution when moving it.

• The HYDRIM should be serviced on site.

• The HYDRIM is equipped with an air gap / anti-suction device to prevent backow of dirty

water into the water supply. No other air gap device is necessary.

• If you need to extend the water inlet and drain hoses, ensure that you use commercial grade

plumbing hose.

• The maximum length of the drain hose is 3.3 m / 13 ft.

Installing the water softener salt:

Unscrew the salt container lid and pour 1 litre / 1 quart of water into

the water softener. Add 1 kg / 2.2 lbs of water softening salt in the

same manner. Screw the salt container cap on tightly.

Handling and installing the HIP™ cleaning solution

The HIP™ cleaning solution is used in dilute form as a detergent for the cleaning

of surgical instruments in the HYDRIM range of washers and washer disinfectors. It is a

colourless and almost odourless liquid which is completely soluble in water.

The pH range of the concentrated solution is between 9.3 to 9.8 and the solution is

therefore alkaline. It is therefore advised that certain precautionary measures are observed

when handling and during the loading of the solution into the machine, and when removing

and disposing of the empty box.

5

4. Installation Instructions

Recommended precautionary measures with regard to safe handling of HIP™ cleaning solution.

• Always wear undamaged gloves made of natural or butyl rubber, nitrile, or neoprene

(Surgical gloves are ideal).

• Always wear eye protection.

• Protect exposed skin on arms.

• If solution is spilled on clothing, remove the item of clothing and wash affected skin

with plenty of water, in accordance with the Material Safety Data Sheet requirements.

• Use good industrial hygiene practices in handling this material. When handling,

do not eat or drink.

• After handling the product, remove and dispose of gloves and wash hands prior to

removing eye protection.

• Do not use the personal protective equipment you use for clinical activities to handle

HIP™ products.

• Always ensure that personal protective equipment, if contaminated with HIP™

cleaning solution, is cleaned, or disposed of as appropriate.

For comprehensive data on HIP™ cleaning solution, please visit SciCan.com to

view or download a PDF of the Material Safety Data Sheet.

To install the HIP™ cleaning solution box, follow these steps:

salt container

Installing Cleaning Solution:

Install HIP™ Cleaning Solution as follows:

Technician Installation Test: Turn on the shut-off valves. Run a cycle, checking for leaks in

the plumbing connections.

6

Water quality

The quality of the water being used in the HYDRIM to clean the instruments is very critical

to achieving satisfactory cleaning results and to protecting the instruments and the internal

parts of the unit from deterioration.

Drinking water typically contains many dissolved solids. The amount of dissolved solids

greatly depends on the local natural geological conditions and they can cause stains, spots

and corrosion on instruments and on the internal parts of the HYDRIM. Among others, Iron,

Manganese, Chloride, and Calcium Carbonate (CaCO

3

) are the dominant dissolved solids

that affect the cleaning results when using a washer.

Iron and Manganese can cause orange and brown or black stains on the instruments and

on the internal parts of the HYDRIM. Chloride is usually responsible for causing stains,

spotting, pitting and scaling. If the instruments or the inner parts of the HYDRIM L110w G4,

such as the chamber, show any of these spots or stains, a water test may be required to

determine the cause. The installation of a water treatment system may be required to

reduce the amount of dissolved solids in the water and to improve the cleaning

performance of the HYDRIM.

Calcium Carbonate is the principle cause of water hardness and leaves white spots or

scales. The HYDRIM is equipped with a built-in water softening system that must be

adjusted according to the local water hardness. Please see the next section of this manual

for recommended regeneration settings.

Before using the HYDRIM, SciCan recommends testing the water and recording

the results for water hardness, pH value, and water conductivity for future reference.

IMPORTANT: The HYDRIM's water softening system reduces the water hardness by

taking out Calcium Carbonate. If your water testing results show that your water hardness

is outside the unit's range of adjustment, or if other dissolved solids in the water cause

stains or deposits on the instruments or chamber, an external water treatment system may

be required.

4. Installation Instructions

7

4. Installation Instructions

Testing water quality

The HYDRIM L110w G4 is equipped with

a built-in water softening system that must

be adjusted according to the local water

hardness. To read local water hardness,

proceed as follows:

1. The water test kit included with your

HYDRIM contains three water

hardness test strips in bags. Take a

water sample from the location where

the machine will be installed.

2. Open one of the bags, remove the

test strip and dip it into the water.

3. Compare the color of the strip with

the chart on the back of the bag

Determine the water hardness according

to the chart on the water test kit envelope.

4. Power the unit on and select the

Settings key from the main menu.

5. Go to the Setup Menu and select

“Set Regeneration”.

6. Using the up and down arrows, set the

water softener regeneration level

according to the water hardness table

in this section. If your water hardness

falls between two settings, select the

higher setting.

7. Unscrew the water softener container

lid from the bottom right of the chamber

and pour at least 1.0 litres (0.26 gal) of water

into the water softener container. Then ﬁll the

salt container to the top (maximum 1 kg/

2.2 lbs.) with salt. Close by screwing the lid

tightly back into place and run a complete

cycle with no instruments. An improper seal can lead to corrosion.

*Please note: The water test strip is only accurate up to 250 ppm. If the reading on the test strip exceeds

250 ppm and/or if the location in which the HYDRIM is installed has known water quality problems, having

a more detailed and accurate water test done by a test lab is strongly recommended.

Water Hardness Conversion and salt regeneration levels

°dH

US

GPG

PPM

(mg CaCO3 / Litre)

Regen.

1 1.0 18

2 2.1 36

3 3.1 54

Very Soft

4 4.2 71

5 5.2 89

5.6 5.8 100

1

6 6.3 107

6.2 6.4 110

7 7.3 125

8 8.3 143

2

8.4 8.8 150

9 9.4 161

10 10.4 178

10.1 10.5 180

11 11.5 196

3

11.2 11.7 200

11.8 12.3 210

Typically

No Treatment

Necessary

(values from 18-143)

External Treatment

Required

(values >535)

Additional

Water

Treatment

Required

May Require External Treatment

(values from 150-535)

12 12.5 214

13 13.6 232

4

14 14.6 250*

15 15.6 268

16 16.7 286

5

16.8 17.5 300

17 17.7 303

18 18.8 321

19 19.8 339

6

19.6 20.5 350

20 20.9 357

20.2 21.0 360

21 21.9 375

22 22.9 393

22.4 23.4 400

23 24.0 411

24 25.0 428

25 26.1 446

7

25.2 26.3 450

26 27.1 464

27 28.2 482

28 29.2 500

28.6 29.8 510

29 30.2 518

30 31. 3 535

≥30.3

≥31.6

≥540

8

5.1 Instrument Reprocessing Recommendations

The HYDRIM L110w G4 is designed to clean general dental and medical instruments.

Terminal sterilization MUST follow processing in the HYDRIM L110w G4.

Prior to placing instruments in the HYDRIM, consult the instrument manufacturer’s reprocessing

instructions.

Examples of medical and dental instruments suitable for cleaning in the HYDRIM L110w G4

include:

• Stainless steel scalers, spatulas and hemostats.

• Stainless steel retractors, needle holders, skin hooks, tissue forceps, scissors, curettes, and

other stainless steel instruments free of deep cavities.

For best results, instruments processed in the HYDRIM L110w G4 should

have the following properties:

• Heat resistance to a temperature of up to 70°C / 158°F

• Corrosion resistance in the presence of heat and alkalinity.

Burs, microkeratomes, phaco tubing, beroptics and electrical equipment should not be processed

in the HYDRIM.

Nickel-plated instruments, or instruments containing aluminum or colour anodized aluminum

as well as single use instruments are not suited for processing in the HYDRIM.

HIP™ (HYDRIM Cleaning Solution with Instrument Protection) has been carefully formulated to

provide outstanding material compatibility with a wide range of metals and coatings. However,

some manufacturers’ instruments or instrument coatings may not be compatible.

Please consult the instrument manufacturer for their recommended cleaning procedures.

In general, it is not recommended to process carbon steel and chrome plated instruments

in the HYDRIM.

All hinged instruments should be placed in open position in open baskets or in the hinged

instrument rack (SciCan part number 01-110409S) in P3 Heavy-Duty cycle.

When processing small or light objects in the HYDRIM use the basket with lid (SciCan part number

01-109966S).

Only the outer surfaces of dental handpieces can be cleaned in the HYDRIM L110w G4 with

the handpiece holder (9 handpieces, PN 01-113113S or 21 Handpieces, PN 01-113112S).

Set-able materials, such as cements, amalgam, and composites need to be removed from the

instruments after use at chairside. The HYDRIM will not be able to clean them off the instruments.

.

5. Instructions for Use

9

5. Instructions for Use

5.2 Cycle Description Chart

10

* This is not a wash cycle. Always run a wash cycle following the rinse & hold cycle.

** Cycle times depend on the temperature and pressure of incoming water.

*** Rinse times are adjustable up to 10 minutes by an authorized technician.

Cycle Prewash Wash

Intermediate

Rinse

Rinse Dry

Total Time

**

w/o Drying

Water

Consumption

P0 – Machine

Cleaning Cycle

No initial draining.

<30ºC/86°F

(cold)

3 minutes

N/A N/A

<30ºC (cold)

2 minutes

N/A

7

minutes

16 L

4.23 Gal

P1 – Rinse and

Hold Cycle*

Use to prevent

soil from drying on

instruments when they

will not be washed

within one hour.

<30ºC/86°F

(cold)

3 minutes

N/A N/A

60ºC/140°F

1 minute

N/A

17

minutes

16 L

4.23 Gal

P2 – Regular

Cycle

Use for moderately

soiled loose

instruments.

N/A

50ºC/122°F

5-15 minutes

(default 5

minutes)

<60ºC/140°F

1 minute

60ºC/140°F***

1-10 minutes

(default 1 minute)

1-20

minutes

(default 10

minutes)

25

minutes

24L

6.34 Gal

P3 – Heavy Duty

Cycle

Use for heavily soiled

instruments and

cassettes.

<30ºC/86°F

(cold)

3 minutes

50ºC/122°F

5-15 minutes

(default 9

minutes)

<60ºC/140°F

1 minute

60ºC/140°F

1 minute

1-20 minutes

(default 10

minutes)

34

minutes

32L

8.45 Gal

5.3 Hints and tips for best cleaning results

Remove all cement, composite material and amalgam from instruments at chairside prior to

processing in the Hydrim.

• Use only accessories, such as baskets, cassettes, trolleys and racks to hold instruments

that are designed for the HYDRIM L110w G4.

• Use accessories for their intended purpose only. For example, do not place hinged

instruments in cassettes. Use the hinged instrument rack instead.

• Disassemble instruments if possible.

• Do not overlap instruments. Each instrument must be kept separate.

• All instruments must be placed in the instrument washer in such a way as to allow good

rinsing of all surfaces. Any surface that is shielded from water and detergent cannot

be cleaned.

• Open hinged instruments widely when placed in baskets or hinged instrument rack

(PN 01-110409S). Closed hinged instruments cannot be cleaned.

• Place suction tubes in the rack for vertical instruments and ensure that water can ﬂow

unrestricted in and out of the tubes. Do not place suction tubes horizontally in a basket

or in a cassette. For instruments containing lumens, such as dental handpieces, only the

external surfaces are cleaned.

• Place trays and other concave shaped items at an angle to ensure water can run off

surfaces easily.

• Do not overload the HYDRIM.

• Verify the Hydrim setup:

– Ensure that the washer spray arms are free of any blockage and can rotate freely.

– Ensure that the mesh ﬁlters in the chamber drain are free from debris.

• To achieve best cleaning results, instruments should be processed in the HYDRIM as

soon as possible. If immediate cleaning is not possible, it is recommended to process

the instruments using the P1 Rinse and Hold program immediately after use on

the patient.

• Visually inspect instruments for cleanliness and integrity (corrosion, material changes)

after cleaning and repair or replace instruments if necessary.

• If process enforced is activated, the operator must conﬁrm that the instruments are

visually clean after a complete cycle is ﬁnished.

11

5. Instructions for Use

5.4 Recommended load congurations

The intended purpose of the L110w G4 washer is a clinical general instrument washer,

predominantly aimed at the general dental and medical markets. There will be many

combinations of instruments that can be processed in the L110w G4 unit depending on:

• Size of practice

• Types of procedures undertaken at any one time

• Specialization of practice

• Instrument management protocols

It is difcult to illustrate all the possible combinations av ailable, so below we have given

examples of the most common typical basket loadings, the recommended loading

of general instruments, and the worst case loading, for which the unit has been type

tested and validated.

Handle all instruments with care to prevent personal injuries through punctures for

example. Follow local health and safety regulations for preventing accidents, bodily

harm and personal injuries.

Observe the instrument manufacturer’s recommendations for cleaning and care.

When loading the unit, arrange loose instruments so that they do not touch one

another. Instruments with concave surfaces or cavities should be placed so that water

can drain freely.

12

Sample loading:

Example 1 – solid straight & hinged instruments

Example 2 – solid straight instruments

5. Instructions for Use

13

Example 7 – instrument trays

Example 6 – instrument sets in cassettes – half load

Example 5 – instrument sets in cassettes – full load

Example 4 – small & disassembled instruments

For example: Two piece mirrors, scalpel knife handles, etc.

For example: Bone ﬁ les, pluggers, curettes, excavators, etc.

Example 3 – hinged instruments, solid instruments and open hollow instruments

For example:

Scalers, curettes,

dental elevators,

single part mirrors,

suction tubes etc.

For example:

Rongeurs, forceps,

scissors etc.

The following are optional:

STATIM 5000 basket.

Part-number

01-107241

Long Basket.

Part-number

01-108232

Full Size Basket.

Part-number

01-111598

14

5. Instructions for Use

Rack for four 11” x 14”

cassettes, for upper

or lower trolley. Full size (1/1).

Part-number

01-109965S

Hinged instrument rack.

Part-number

01-110409S

STATIM 2000 basket.

Part-number

01-107240

Rack for ve 8” x11”

cassettes, for upper

or lower trolley. Full size (1/1).

Part-number

01-109963S

Rack for ve medium

size cassettes, for upper

or lower trolley. Half-size (1/2).

Part-number

01-109964S

Basket with lid.

Quarter size (1/4).

Part-number

01-109966S

Hygiene basket for

loose instruments.

Quarter size (1/4).

Part-number

01-109967S

5.5 Baskets and Accessories

The following are included with the HYDRIM:

5. Instructions for Use

Settings

Unlock door

Water softener,

detergent level,

and door status

Network connectivity

(green when active)

Programs

USB status

(green when active)

5.6 Touchscreen overview

15

5. Instructions for Use

User Technician Setup

5.7 Set up menu overview

Set EOL CR/LF

Set Regeneration

LCD Contrast

Theme

Remote Screen

Instructions

Instructions Delay

Remote Access

Prepare for Shipping

Baud RateLanguage

Country

Date/Time

Unit No.

Network Setup

Screen Saver

Temperature C/F

Set Button Beep

Beep Volume

Set Printer

Cleaning

Set Drying Time

Set Wash Time

Cycle Count

Process Enforced

User

16

5.8 Setting the language

The messages displayed by your HYDRIM can be presented in a number of different

languages. To change the current language, follow these steps:

1.

2. Scroll to

Language

and select.

3. From the LANGUAGE screen, press to scroll through the list of languages.

When you have found the desired language, press

to save your selection and return

to the Setup menu.

5.9 Setting the country

1.

2. Scroll to

Country

and select.

3. Using the keypad, type the name of the country and press

EN

to select. Press

to save and return to the Setup menu.

5.10 Setting the time

1.

2. Scroll to

Date / Time

and select TIME.

3. From the TIME screen, use the keypad to set the time. Press

EN

to save and

to return to the Setup menu.

NOTE: If the HYDRIM is connected to a network, it is important to also enter the correct

Time Zone. Enter the Time submenu, select Time Zone and scroll and select your local

time zone.

4. To change your unit to display 12-hour time format (24-hour time format is the default

setting), go to the Setup menu and use

to scroll to TIME 12/24, select it and

toggle to 12. Press

to save and return to the Setup menu.

5. To activate daylight savings time (DST), go to the Setup menu and use

to scroll

to DST ON/OFF and select. Use

to toggle DST ON or OFF and press the

to save and return to the Setup menu. If connected to the network, the time will

automatically adjust to DST.

17

5. Instructions for Use

5.11 Setting the date

1.

2. Scroll to

Date / Time

and select DATE.

3. From the DATE screen, use the keypad to set the date. Press

EN

to save and

to return to the Setup menu.

4. To change the format in which the date appears, return to the Setup menu and use

to scroll to DATE FORMAT. Select it, and follow the prompts to have

the date displayed in the desired format. Press

to save and return to

the Setup menu.

5.12 Assigning unit identi er number

1.

2. Scroll to

Unit No

and select.

3. Using the keypad, select a maximum of 3 digits to be used as the unit’s identiﬁ er

number. Press

EN

to save and to return to the Setup menu.

5.13 Adjusting the screensaver delay

To change the length of time before the screensaver is activated, follow these steps:

1.

2. Scroll to

Screensaver

and select.

3. Use to scroll through your time options. When you have found the amount of

time you require, press it. Press

to save and return to the Setup menu.

5.14 Adjusting the temperature display

1.

2. Scroll to

Temperature C/F

and select.

3. Use to choose between having information displayed in degrees Celsius or

Fahrenheit. Press

to save and return to the Setup menu.

18

5. Instructions for Use

Page is loading ...

SciCan HYDRIM L110w G4 User manual

SciCan HYDRIM L110w G4 User manual

in other languages

Related papers

Other documents