Hitachi 62VS69A User manual

Brand: Hitachi

Model: 62VS69A

Category: TVs & monitors

Type: User manual

This manual is also suitable for

No. 0220

50VS69A/LC67

55VS69A/LC67

62VS69A/LC67

R/C: CLU-4351UG2

NTSC

A C

hassis

SERVICE MANUAL

SERVICE MANUAL REVISION HISTORY INFORMATION

DATE REVISON # REASON

June, 9 SM00001 FIRST ISSUE OF MANUAL

ATSC

JUNE 2006 HHEA-MANUFACTURING DIVISION

LCD REAR PROJECTION TELEVISION

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

LC67

CH 1

Part Numbers Added

2006.12.13

2006.11.27

Part numbers corrected

CH 2

2007.05.12

Drawing numbers corrected

CH 3

JUNE 2006 HHEA-MANUFACTURING DIVISION

No. 0220

LC6X

A C

hassis

CONTENTS

SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

PRODUCT SAFETY NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

SERVICING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

AGENCY REGULATORY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

ACKNOWLEDGMENTS AND TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

FEATURES & SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

BASIC SETUP & OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

TROUBLESHOOTING FLOWCHARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

CONNECTION DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

FINAL WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

QUICK DISASSEMBLY GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

FINAL ASSEMBLY GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

WAVEFORMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

DC VOLTAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

CIRCUIT SCHEMATIC DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

PRINTED CIRCUIT BOARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107

QUICK REFERENCE PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of

electric shock do not perform any servicing other than that contained in the operating instructions

unless you are qualified to do so. Before servicing this chassis, it is important that the service

technician read the “IMPORTANT SAFETY INSTRUCTIONS” in this service manual.

SAFETY NOTICE

USE ISOLATION TRANSFORMER WHEN SERVICING

Components having special safety characteristics are identified by a on the schematics and on the parts list in this

Service Data and its supplements and bulletins. Before servicing the chassis, it is important that the service technician

read and follow the “Important Safety Instructions” in this Service Manual.

TO GO TO A CHAPTER, CLICK ON ITS HEADING BELOW

SERVICE MANUAL

NTSC

ATSC

LC67

50VS69A/LC67

55VS69A/LC67

62VS69A/LC67

R/C: CLU-4351UG2

LCD REAR PROJECTION TELEVISION

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

NOTICE: Comply with all cautions and safety-related notes

located on or inside the cover case and on the chassis or plasma

module.

WARNING: Since the chassis of this receiver is connected to

one side of the AC power supply during operation, whenever the

receiver is plugged in service should not be attempted by any-

one unfamiliar with the precautions necessary when working on

this type of receiver.

1. When service is required, an isolation transformer should be

inserted between power line and the receiver before any

service is performed on a “HOT” chassis receiver.

2. When replacing a chassis in the receiver, all the protective

devices must be put back in place, such as barriers, non-

metallic knobs, insulating cover-shields, and isolation

resistors, capacitors, etc.

3. When service is required, observe the original lead dress.

4. Always use manufacturer’s replacement components. Critical

components as indicated on the circuit diagram should not be

replaced by another manufacturer’s. Furthermore, where a

short circuit has occurred, replace those components that

indicate evidence of over heating.

5. Before returning a serviced receiver to the customer, the

service technician must thoroughly test the unit to be certain

that it is completely safe to operate without danger of electrical

shock, and be sure that no protective device built into the

receiver by the manufacturer has become defective, or

inadvertently defeated during servicing.

Therefore, the following checks should be performed for the

continued protection of the customer and service technician.

Leakage Current Cold Check

With the AC plug removed from the 120V AC 60Hz source,

place a jumper across Line 1 and Line 2 of the three plug

prongs, do not connect with the third prong, which is physical

ground.

Using an insulation tester (DC500V), connect one of its leads

to the AC plug jumper and touch with the other lead each

exposed metal part (antennas, screwheads, metal overlays,

control shafts, etc.), particularly any exposed metal part

having a return path to the chassis should have a resistor

reading over 4MΩ. Any resistance value below this range

indicates an abnormality which requires corrective action. An

exposed metal part not having a return path to the chassis will

indicate an open circuit.

SAFETY PRECAUTIONS

Leakage Current Hot Check

AC LEAKAGE TEST

ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED

ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD

AND MUST BE CORRECTED BEFORE RETURNING THE

RECEIVER TO THE CUSTOMER.

LEAKAGE

CURRENT

TESTER

(READING

SHOULD NOT

BE ABOVE 0.5MIU)

EARTH

GROUND

TEST ALL

EXPOSED

METAL SURFACES

DEVICE

UNDER

TEST

3-WIRE CORD

ALSO TEST WITH PLUG

REVERSED

(USING AC ADAPTER

PLUS AS REQUIRED)

Plug the AC line cord directly into a 120V AC outlet. (Do not use an

isolation transformer during this test.) Use a leakage current

tester or a metering system that complies with the American

National Standards Institute (ANSI) C101.0 Leakage Current

for Appliances. In the case of the PDP monitor set the AC

switch first in the ON position and then in the OFF position,

measure from across Line 1 and Line 2 of the three plug

prongs, do not connect with the third prong, which is physical

ground, to all exposed metal parts of the instrument

(antennas, handle bracket, metal cabinet, screw heads,

metallic overlays, control shafts, etc.), especially any exposed

metal parts that offer an electrical return path to the chassis.

Any current measured must not exceed 0.5 MIU. Reverse the

instrument power cord plug in the outlet and repeat test.

LC67

TABLE OF CONTENTS

Many electrical and mechanical parts in HITACHI television

receivers have special safety-related characteristics. These are

often not evident from visual inspection nor can the protection

afforded by them necessarily be obtained by using replacement

components rated for higher voltage, wattage, etc. Replacement

parts which have these special safety characteristics are identified

in this Service Manual.

Electrical components having such features are identified with an

! mark in the schematics and parts list in this Service Manual.

The use of a substitute replacement component which does not

have the same safety characteristics as the HITACHI-recom-

mended replacement component, shown in the parts list in this

Service Manual, may create shock, fire, or other hazards.

Production safety is continuously under review and new instruc-

tions are issued from time to time. For the latest information,

always consult the current HITACHI Service Manual. A subscrip-

tion to, or additional copies of HITACHI Service Manuals may be

obtained at a nominal charge from HITACHI Sales Corporation.

Ultraviolet Radiation

OPTIC UNIT: The primary source of Ultraviolet Radiation in this

receiver is the optic unit. The optic unit utilized in this chassis is

specially constructed to limit Ultraviolet Radiation emissions. For

continued Ultraviolet Radiation protection, the replacement optic

unit must be the same type as the original HITACHI-approved

type.

Service Personnel - WARNING

Eye damage may result from directly viewing the light produced by

the lamp used in this product. Always turn off lamp before open-

ing optic unit. Ultraviolet radiation eye protection required during

servicing.

When troubleshooting and making test measurements in a receiv-

er with an excessive high voltage problem, avoid being unneces-

sarily close to the optic unit and the high voltage component.

Do not operate the chassis longer than is necessary to locate the

cause of excessive voltage.

This Service Manual is intended for qualified service techni-

cians; it is not meant for the casual do-it-yourselfer. Qualified

technicians have the necessary test equipment and tools, and

have been trained to properly and safely repair complex prod-

ucts such as those covered by this manual. Improperly per-

formed repairs can adversely affect the safety and reliability of

the product and may void warranty. Consumers should not risk

trying to do the necessary repairs and should refer to a quali-

fied service technician.

WARNING

Lead in solder used in this product is listed by the California Health

and Welfare agency as a known reproductive toxicant which may

cause birth defects or other reproductive harm (California Health

and Safety Code, Section 25249.5).

When servicing or handling circuit boards and other compo-

nents which contain lead in solder, avoid unprotected skin

contact with solder. Also, when soldering do not inhale any

smoke or fumes produced.

SAFETY NOTICE

USE ISOLATION TRANSFORMER

WHEN SERVICING

Components having special safety characteristics identi-

fied by

on the parts list in this service manual and its

supplements and bulletins. Before servicing this product, it

is important that the service technician read and follow the

“Safety Precautions” and the “Product Safety Notices” in

this Service Manual.

For continued ultraviolet protection, replace optic unit with

original type or HITACHI equivalent type.

POWER SOURCE

This television receiver is designed to operate on 120

Volts/60Hz, AC house current. Insert the power cord into

a 120 Volts/60Hz outlet.

NEVER CONNECT THE TV TO OTHER THAN THE

SPECIFIED VOLTAGE OR TO DIRECT CURRENT.

CAUTION!

The following symbol near the fuse indicates fast operat-

ing fuse (to be replaced). Fuse ratings appear within the

symbol.

Example:

The rating of fuse F902 is 6.0A-125V.

Replace with the same type of fuse for continued protec-

tion against fire.

The lamp in this product contains Mercury.

Dispose of properly in accordance with applicable

environmental laws. For Recycling and Disposal

information, contact your respective governmen-

tal agencies or the Electronic Industries Alliance

at www.eiae.org (in the U.S.) or Electronic

Product Stewardship Canada at www.epsc.ca (in

Canada).

PRODUCT SAFETY NOTICE

125V

NOTE:

F902

LC67

TABLE OF CONTENTS

CAUTION: Before servicing instruments covered by this service

data and its supplements and addenda, read and follow the SAFE-

TY PRECAUTIONS on page 2 of this publication.

NOTE: If unforseen circumstances create conflict between the fol-

lowing SERVICING PRECAUTIONS and any of the SAFETY INS-

TRUCTIONS on page 2 of this publication, always follow the SAFE

TY INSTRUCTIONS.

Remember: Safety First.

General Servicing Guidelines

1. Always unplug the instrument AC power cord from the AC power

source before:

a. Removing or reinstalling any component, circuit board,

module, or any other instrument assembly.

b. Disconnecting or reconnecting any instrument electrical

plug or other electrical connection.

c. Connecting a test substitute in parallel with an electrolyt-

ic capacitor in the instrument.

CAUTION: A wrong part substitution or incorrect

polarity installation of electrolytic

capacitors may result in an

explosion hazard.

2. Do not spray chemicals on or near this instrument or any of its

assemblies.

3. Unless specified otherwise in these service data, clean electri-

cal contacts by applying the following mixture to the contacts

with a pipe cleaner, cotton-tipped stick or comparable nonabra-

sive applicator: 10% (by volume) Acetone and 90% (by volume)

ispropyle alchohol (90%-99% strength).

CAUTION: This is a flammable mixture. Unless specified

otherwise in these service data, lubrication of

contacts is not required.

4. Do not defeat any plug/socket B+ voltage interlocks with which

instruments covered by this service data might be equipped.

5. Do not apply AC power to this instrument and/or any of its elec-

trical assemblies unless all solid-state device heat-sinks are cor-

rectly installed.

6. Always connect the test instrument ground lead to the appropri-

ate instrument chassis ground before connecting the test instru-

ment positive lead. Always remove the test instrument ground

lead last.

7. Use with this instrument only the test fixtures specified in this

service data.

CAUTION: Do not connect the test fixture ground strap to

any heatsink in this instrument.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily

by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES

devices are integrated circuits and some field-effect transistors and

semiconductor “chip” components. The following techniques should

be used to help reduce the incidence of component damage caused

by static electricity.

1. Immediately before handling any semiconductor component or

semiconductor-equipped assembly, drain off any electrostatic

charge on your body by touching a known earth ground.

Alternatively, obtain and wear a commercially available dis-

charging wrist strap device, which should be removed for poten-

tial shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES

devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge build-up or expo-

sure of the assembly.

3. Use only a grounded-tip soldering iron to solder or desolder ES

devices.

4. Use only an anti-static type solder removal device. Some sol-

der removal devices not classified as “anti-static” can generate

electrical charges sufficient to damage ES device.

5. Do not use freon-propelled chemicals. These can generate

electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective

package until immediately before you are ready to install it.

(Most replacement ES devices are packaged with leads electri-

cally shorted together by conductive foam, aluminum foil or

comparable conductive material.)

7. Immediately before removing the protective material from the

leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be

installed.

CAUTION: Be sure no power is applied to the chassis or

circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replace-

ment ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot

from a carpeted floor can generate static electricity sufficient to

damage an ES device.)

TABLE OF CONTENTS

SERVICING PRECAUTIONS

LC67

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate

tip size and shape that will maintain tip temperature within the

range 500°F to 600°F.

2. Use an appropriate gauge of resin-core solder composed of 60

parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well-tinned.

4. Thoroughly clean the surfaces to be soldered. Use a small wire-

bristle (0.5 inch or 1.25 cm) brush with a metal handle. Do not

use freon-propelled spray-on cleaners.

5. Use the following desoldering technique.

a. Allow the soldering iron tip to reach normal temperature

(500°F to 600°F).

b. Heat the component lead until the solder melts. Quickly

draw away the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique.

a. Allow the sodering iron tip to reach normal temperature

(500°F to 600°F).

b. First, hold the soldering iron tip and solder strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it

there only until the solder flows onto and around both the

component lead and the foil.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil or components.

d. Closely inspect the solder area and remove any excess

or splashed solder with a small wire-bristle brush.

IC Removal/Replacement

Some Hitachi unitized chassis circuit boards have slotted holes

(oblong) through which the IC leads are inserted and then bent flat

against the circuit foil. When holes are the slotted type, the follow-

ing technique should be used to remove and replace the IC. When

working with boards using the familiar round hole, use the standard

technique as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gent-

ly prying up on the lead with the soldering iron tip as the solder

melts.

2. Draw away the melted solder with an anti-static suction-type sol

der removal device (or with solder braid) before removing the

IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and

solder it.

3. Clean the soldered areas with a small wire-bristle brush. (It is

not necessary to reapply acrylic coating to areas.)

“Small-signal” Discrete Transistor Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as

possible to the component body.

2. Bend into a “U” shape the end of each of three leads remain-

ing on the circuit board.

3. Bend into a “U” shape the replacement transistor leads.

4. Connect to replacement transistor leads to the corresponding

leads extending from the circuit board and crimp the “U” with

long nose pliers to insure metal to metal contact, then solder

each connection.

Power Output Transistor Devices Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heatsink mounting screw (if so equipped).

3. Carefully remove the transistor from the circuit board.

4. Insert new transistor in circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heatsink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as pos-

silbe to diode body.

2. Bend the two remaining leads perpendicularly to the circuit

board.

3. Observing diode polarity, wrap each lead of the new diode

around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of

the two “original leads”. If they are not shiny, reheat them

and, if necessary, apply additional solder.

Use Soldering Iron to Pry Leads

SERVICING PRECAUTIONS

LC67

SERVICING PRECAUTIONS

Fuses and conventional Resistor Removal/Replacement

1. Clip each fuse or resistor lead at top of circuit board hollow

stake.

2. Securely crimp leads of replacement component around stake

1/8 inch from top.

3. Solder the connections.

CAUTION: Maintain original spacing between the replaced

component and adjacent components and the

circuit board, to prevent excessive component

temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit board

will weaken the adhesive that bonds the foil to the circuit board,

causing the foil to separate from, or “lift-off” the board. The follow-

ing guidelines and procedures should be followed whenever this

condition is encountered.

In Critical Copper Pattern Areas

High component/copper pattern density and/or special voltage/cur-

rent characteristics make the spacing and integrity of copper pattern

in some circuit board areas more critical than in others. The circuit

foil in these area is designated as Critical Copper Pattern. Because

Critical Copper Pattern requires special soldering techniques to

ensure the maintenance of reliability and safety standards, contact

your Hitachi personnel.

At IC Connections

To repair defective copper pattern at IC connections, use the follow-

ing procedure to install a jumper wire on the copper pattern side of

the circuit board. (Use this technique only on IC connections.)

1. Carefully remove the damaged copper pattern with a sharp

knife. (Remove only as much copper as absolutely necessary.)

2. Carefully scratch away the solder resist and acrylic coating (if

used) from the end of the remaining copper pattern.

3. Bend a small “U” in one end of a small-gauge jumper wire and

carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the cut-away copper

pattern and let it overlap the previously scraped end of the good

copper pattern. Solder the overlapped area, and clip off any

excess jumper wire.

At Other Connections

Use the following technique to repair defective copper pattern at

connections other than IC Pins. This technique involves the instal-

lation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife.

Remove at least 1/4 inch of copper, to ensure hazardous condi-

tion will not exist if the jumper wire opens.

2. Trace along the copper pattern from both wire sides of the pat-

tern break and locate the nearest component directly connected

to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the nearest com-

ponent on one side of the pattern break to the lead of the near-

est component on the other side. Carefully crimp and solder the

connections.

CAUTION: Be sure the insulated jumper wire is dressed so

that it does not touch components or sharp

edges.

Frequency Synthesis (FS) Tuning Systems

1. Always unplug the instrument AC power cord before discon-

necting or reconnecting FS tuning system cables and before

removing or inserting FS tuning system modules.

2. The FS tuner must never be disconnected from the FS tuning

control module while the power is applied to the instrument.

3. When troubleshooting intermittent problems that might be

caused by defective cable connection(s) to the FS tuning sys-

tem, remove the instrument AC power as soon as the defective

connector is found and finish confirming the bad connection with

a continuity test. This procedure will reduce the probability of

electrical overstress of the FS system semi-conductor compo-

nents.

CRIMP AND

SOLDER

BARE JUMPER

WIRE

Install Jumper Wire and Solder

DEFECTIVE

COPPER

REMOVED

Insulated Jumper Wire

LC67

Leadless Chip Components

(surface mount)

Chip components must be replaced with identical chips due

to critical foil track spacing. There are no holes in the board

to mount standard transistors or diodes. Some chip capaci-

tor or resistor board solder pads may have holes through the

board, however the hole diameter limits standard resistor

replacement to 1/8 watt. Standard capacitors may also be

limited for the same reason. It is recommended that identi-

cal chip components be used. .

Chip resistors have a three digit numerical resistance code

-1st and 2nd significant digits and a multiplier. Example: 162

= 1600 or 1.6K resistor, 0 = 0 (jumper).

Chip capacitors generally do not have the value indicated on

the capacitor. The color of the component indicates the gen-

eral range of the capacitance.

Chip transistors are identified by a two letter code. The first

letter indicates the type and the second letter, the grade of

transistor.

Chip diodes have a two letter identification code as per the

code chart and are a dual diode pack with either

common anode or common cathode. Check the parts list for

correct diode number.

Component Removal

1. Use solder wick to remove solder from component end

caps or terminals.

2. Without pulling up, carefully twist the component with

tweezers to break the adhesive.

3. Do not reuse removed leadless or chip components

since they are subject to stress fracture during removal.

Chip Component Installation

1. Put a small amount of solder on the board soldering

pads.

2. Hold the chip component against the soldering pads

with tweezers or with a miniature alligator clip and apply

heat to the pad area with a 30 watt iron until solder

flows. Do not apply heat for more than 3 seconds

How to Replace Flat-lC

—Required Tools—

• Soldering iron • iron wire or small awl

• De-solder braids • Magnifier

1. Remove the solder from all of the pins of a Flat-lC by

using a de-solder braid.

2. Put the iron wire under the pins of the Flat-lC and pull it

in the direction indicated while heating the pins using a

soldering iron. A small awl can be used instead of the

iron wire.

3. Remove the solder from all of the pads of the Flat-

lC by using

a de-solder braid.

4. Position the new Flat-lC in place (apply the pins of the

Flat-lC to the soldering pads where the pins need to be

soldered). Properly determine the

positions of the soldering pads

and pins by correctly aligning the

polarity symbol.

6. Check with a magnifier for solder bridge between the

pins or for dry joint between pins and soldering pads. To

remove a solder bridge, use a de-solder braid as shown

in the figure below.

NOTE: These components are affixed with glue. Be careful not to break or damage any foil under the

component or at the pins of the ICs when removing. Usually applying heat to the component for a short

time while twisting with tweezers will break the component loose.

Chip Components

TYPE

GRADE

SOLDER

CAPS

TRANSISTOR

CAPACITOR

1ST DIGIT

2ND DIGIT

MULTIPLIER

= 1600 = 1.6K

ANODES

MH DIODE

RESISTOR

SOLDER CAPS

COMMON CATHODE

Flat-IC

De-Solder

Braid

Soldering

Iron

Soldering

Iron

Soldering

Iron

Soldering

Iron

Soldering

Iron

Soldering

Iron

De-Solder

Braid

Flat-IC

Solder

Bridge

Solder

De-Solder

Braid

Iron

Wire

Pull

Awl

Polarity Symbol

5. Solder all pins to the soldering pads using a fine tipped

soldering iron.

LC67

SERVICING PRECAUTIONS

Information for service about lead-free solder Introduction

Hitachi introduced lead-free solder to conserve the "Earth Environment".

Please refer to the following before servicing.

(1) Characteristic of lead-free solder

Melting point of lead free solder is 40-50

C higher than solder containing lead.

(2) Solder for service

Following composition is recommended.

" Sn - 3.0Ag - 0.5Cu " , or " Sn - 0.7 Cu "

Lead solder can be used, but there is a possibility of failure due to insufficient strength of the solder.

Caution when using solder containing lead.

Please remove previous solder as much as possible from the soldering point.

When soldering, please perfectly melt the lead-free solder to mix well with the previous solder.

(3) Soldering iron for lead-free solder.

Melting point of lead-free solder is higher than solder containing lead.

Use of a soldering tool "with temperature control" and "with much thermal capacitance" is recommended.

(Recommended temperature control : 320

C - 450

Recommended temperature

PWB with chip parts

320

C +/- 30

PWB without chip parts

380

C +/- 30

Chassis, metal, shield etc.

420

C +/- 30

(4) Identification of lead-free PWB

2004 models >> lead-free solder is introduced

2006 models >> lead-free solder apply

On lead-free PWB, "F" is added at the beginning of stamp on PWB. (e.g. DW2U-POD F)

LC67

AGENCY REGULATORY

INFORMATION

TABLE OF CONTENTS

LC67

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

FCC Information

This device complies with part15 of the FCC Rules.Operation is subject to the following two conditions :

(1) This device may not cause harmful interference and (2) This device must accept any interference

received, including interference that may cause undesired operation.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not

expressly approved by Hitachi America ,Ltd. Home Electronics Division may void the user’s authority to

Cables

Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to

maintain compliance with FCC Rules and Regulations.

Any cables that are supplied with the system must be replaced with identical cables in order to assure

compliance with FCC rules. Order Hitachi spares as replacement cables.

AGENCY REGULATORY INFORMATION

operate the equipment.

This LCD

Rear Projection Televisionreceiver will display television closed captioning,(or),in

accordance with paragraph 15.119 and 15.122 of the FCC rules.

Note

Cable Compatible Television Apparatus- Tèlèvision câblocompatible, Canada.

INDUSTRY CANADA AGENCY REGULATORY INFORMATION

HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI Licensing

LLC.

㪚㪦㪧㪰㪩㪠㪞㪟㪫㩷㪺㩷㪈㪐㪐㪐㪄㪉㪇㪇㪍㩷㪤㪦㪥㪫㪘㪭㪠㪪㪫㪘㩷㪪㪦㪝㪫㪮㪘㪩㪜㪃㩷㪠㪥㪚㪅㩷㪘㪣㪣㩷㪩㪠㪞㪟㪫㪪㩷㪩㪜㪪㪜㪩㪭㪜㪛㪅

ACKNOWLEDGMENTS

AND TRADEMARKS

This LCD Television complies with VESA DDC2B specifications, Plug & Play

is a system with computer, peripherals (including monitors) and operating

system. It works when the monitor is connected to a DDC ready computer that

is running an operating system software that is capable for the plug & play.

When a Plug and Play PC is powered on, it sends a command to the Monitor

requesting identification. The Monitor sends back a string of data including its

characteristics.

TRADEMARK ACKNOWLEDGMENT

DDC is a trademark of Video Electronics Standard Association.

IBM PC/AT and VGA are registered trademarkds of International Business Machines Corporation of the U.S.A.

Apple and Macintosh are registered trademarks of Apple Computer, Inc.

VESA is a trademark of a nonprofit organization, Video Electronics Standard Association.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Cable Compatible Television Apparatus- Tèlèvision câblocompatible, Canada.

*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

LC67

TABLE OF CONTENTS

The LC6x are LCD-based rear projection TV receiver. The LC6x are optimized for high

definition and standard definition video signals. These include video enhancement

functions (luminance and chroma transient improvement, noise reduction system), PinP/

PoutP/ Multi-windowed picture function. It combines the video signal processing electronics,

high contrast ratio) optical engine and high intensity UHP lamp enclosed in the slim &

compact designed plastic cabinet. These also include ATSC receiver and POD function.

The differences between each set are shown b

elow.

No. Model name ATSC POD IEEE1394

/5C

RS232C

V-CHIPS

1 62VS69A X X – X X

2 55VS69A X X – X X

3 50VS69A X X – X X

These incorporate cooling fan system to prevent from overheating.

The power consumption in stand-by mode should not exceed the value shown below.

Maximum rating No. MODEL

NAME

[W] [A]

Average

rating [W]

POD

[W]

*1)

Stand-by

[W]

*2)

Chassis

62VS69A

177 2.8 171 14.9 0.6

LC67

55VS69A

177 2.8 171 14.9 0.6

LC67

50VS69A

177 2.8 171 14.9 0.6

LC67

*1) It should be ≤ 15W to comply with Energy Star

*2) It should be ≤ 1.0W to comply with Energy Star

INTRODUCTION

LC67

TABLE OF CONTENTS

This HITACHI Service Manual is intended for the qualified service personnel and it contains

the necessary information for troubleshooting the LCD Rear Projection Television set in case of malfunction.

POWER RATINGS:

TABLE OF CONTENTS

LC67

Features:

Screen mode availability varies by input format

HDTV Televisions display HDTV only when an HDTV source is available.

All specifications, weights, and dimensions are subject to change without

prior notice. Please access www.hitachi.com/tv for detailed specifications

and dimensions for custom installations.

UltraVision Digital is a registered trademark of Hitachi Home Electronics

(America), Inc.

HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI Licensing

LLC.

*Manufactured under license from Dolby Laboratories. “Dolby” and the

double-D symbol are trademarks of Dolby Laboratories.

New Easy-to-Use On-Sc reen Menu Control (3

Language)

• Preprogrammed Remote Control

• Power Management: ON/OFF via signal detection

• Picture Enhancement

• Input Signal Identification

• CableCARD compatible - Contact your local cable

operator for more information

• HDMI (High Definition Multimedia Interface)(High

Bandwidth Digital Content Protection V1.1

Compatible)

• Technology

Video:

• Superfine Picture Quality; 1280 Line Horizontal

Resolution

• Video Input Sensor

• 3 Color Temperature Presets: High, Standard ,

Medium.

• Multiple Screen Fill Modes

(4:3 Standard/Expanded/Zoom1/

Zoom2/16:9 Standard/Zoom)

• 4MB 10-bit 3D Y/C Comb Filter

•

Picture Modes (Day-Normal, Day-Dynamic and Night)

•

Inputs:

Downloadable V-Chip

•

Power Input . . . . . . . . . . . . . . . . . . . . .AC

• Surround Sound

120V, 60Hz

• Television System . . . . . . . . . . . . . . . NTSC Standard

• Power Consumption

- Refer to rear panel at the back of the TV set

ATSC Standard (8 VSB, 64-QAM, 256-QAM)

Stand-by Power .. ............................ Less than 1 Watt

• Antenna input impedance . . . . . . . . . . . . . . . .75 Ohm

• Channel coverage . . . . . . . . . . . . . . . . . . . . . . . 191ch.

DIMENSIONS

50VS69A 55VS69A 62VS69A

Hei

ht (in.)

31 15/16 34 13/16 38 13/16

(mm)

812.0 884.0 985.0

Wid

th (in.)

46 5/16 50 11/16 56 13/

(mm)

1,177.0 1,288.0 1443.0

pth (in.)

17 5/16 17 11/16 19 1/2

(mm)

439.0 449.0 495.0

Wei

ght (lbs.)

79 86 104

(kg.)

36 39 47

TE:

Due

to improvements, specifications in this

opera

ting guide are subject to change

without

notice.

VHF-Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ~ 13

UHF-Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ~ 69

CATV Mid Band . . . . . . . . . . . . . . . . . . . . . . A-5 ~ A-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-I

Super Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J-W

Hyper Band . . . . . . . . . . . . . . . . . . . . . . . W+1 - W+28

Ultra Band . . . . . . . . . . . . . . . . . . . . . . . W+29 - W+94

• Video . . . . . . . . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm

• S-Video

Luminance (Y) . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm

Chrominance (C) . . . . . . . . . . . . . 0.286Vp-p, 75 Ohm

• Component Video

Luminance (Y) . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm

Chrominance (P

) . . . . . . . . . . . 0.7Vp-p, 75 Ohm

• Audio input Impedance . . . . . . . . . . . . . . . . 270k Ohm

• Average input level . . . . . . . . . . . . . . . . . . . 470mVrms

• HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (19 PIN)

Outputs:

• Video1.0Vp-p. 75 Ohm

• Audio . . . . . . . . . . . . . . . . . . . . . . .470mVrms, 1k Ohm

• Optical Out (Digital Audio) . . . . . .1 Optical Connector

Audio:

• MTS Stereo/SAP

• Bass Boost

• 24W

• Soft Mute (50%)

Supplied Accessories:

• Remote Control

• Batteries

Optional Accessories:

• For U.S. Models: Please access our website:

www.hitachi.us/tv

INPUTS/OUTPUTS

• Wideband Component Y, Pb,Pr . . . . . . . . . . . . . . . . 3

• Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

• SVideo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

• Antenna (RF) Input . . . . . . . . . . . . . . . . . . . . . . . . . . 1

• Audio Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

• Monitor Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

• Optical Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

• CableCARD Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

• Upgrade Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . 1

• HDMI. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

•

Features & Specifications

SPECIFICATIONS

A/V TERMINALS

REAR

No. MODEL

NAME

A/V

S-video

COMP

HDMI

Monitor

Out

Monitor

S Out

A Out

Cent In

L(mono)

ANT

Optical

Out

Card

1 62VS69A 4 2 2 2 1 1 1 1 1 1 1

2 55VS69A 4 2 2 2 1 1 1 1 1 1 1

3 50VS69A 4 2 2 2 1 1 1 1 1 1 1

4 50C20A 4 2 2 2 1 1 1 1 1 1 1

REAR FRONT (or SIDE)

No.

MODEL

NAME

POD

Card

RS232C

A/V

COMP

1 62VS69A 1 1 1 1

2 55VS69A 1 1 1 1

3 50VS69A 1 1 1 1

4 50C20A 1 1 1 1

Remark: *1 “Monitor out” and “Audio to HiFi” share one terminal and are switched by user menu.

STRUCTURAL DIMENSIONS

No. Model name Width Height Depth Weight

(mm) (mm) (mm) (kg)

62VS69A 1443 985 495 47

2 55VS69A 1288 884 449 39

3 50VS69A 1177 812 439 36

4 50C20A 1387 901 415 41

LC67

MAIN PARTS

(1) LCD panel

LC6x occupies 3 LCD panels (for Red, Green and Blue color).

No. Item Description

1 Product name

Blue: L3D07H-51G01B / L3D07H-52G01B

Red: L3D07H-51G01R / L3D07H-52G01R

Green: L3D07H-51G01G / L3D07H-52G01G

2 System type TFT Active matrix

3 Pixels 1284 (H) x 724 (V)

4 Panel size 0.7”

5 Dot pitch 12 µm

6 Life time More than 20,000h (@Ta ≤ 35°C, worst UV filter combination)

The LCD panel is a UV light sensitive device. The UV ray which illuminates

LCD panel should be cut with three UV filters with 50% cut wavelength of

430nm+430nm+430nm (nominal) and 427nm+427nm+426nm (worst

combination).

(2) Lamp

No. Item Description

1 Input electricity 120W

2 Manufacture Philips

3 Model name UHP 100W/120W

1.0 PH1 P22

4 Type UHP lamp

5 Arc length 1.0mm

6 Life time

(50% survival

rate)

More than 6,000h

7 Applied model

62VS69A

55VS69A

50VS69A

50C20A

Mercury legislation: Apply Hg mark on body

SPECIFICATIONS

LC67

Screen Size　(WxH) 1

Aspect Ratio 2

Set Dimension WxHxD(mm) 3

Set Weight　(kg) 4

Device 5 3 Panels System

Image size

Active dots 6 Excess dot:4dot(H),4dot(V) included

Lens 7

Screen pitch H-lenchi 8

Fresnel

Shield 9

View Hor.(Half brightness) 10

angle Ver.(Half brightness) 11

Mirror

Brightness[cd/㎡]12

ATSC FE 13

With POD 14

15 ATSC/NTSC 1 Tuner(LC67)

Comb Filter 16

Color Temp. 17 High/Med/Std

Output power 18

L/R SPEAKERs 19

DOLBY 20

Sound function 21

Signal processing system

ＰｉｎＰ 23

ＯＳＤ 24

MENU LANGUAGE 25

Photo display 26

3/2 Pulldown 27

Fill Mode 28

Memory by inputs 29

EPG 30

Downloadable V Chip 31

Energy Star 32

AV NET 33

Remote Control 34

VIDEO INPUT 35

S-VIDEO INPUT 36

COMPONENT VIDEO 37

TV as Center 38

Digital Interface 39

IEEE-1394/5C 40

RS-232C 41

DV 42

IR BLASTER OUT 43

MONITOR OUT 44

S-VIDEO OUTPUT 45

AUDIO TO Hi-Fi 46

Lamp 47

Lamp life time 48 Residual ratio 50％

Direction of lamp taking out

Exchange lamp 50

Acoustic noise 51 1m away from PTV

23dB(Front)

Others

UHP 120W(Philips) UHP 120W(Philips)

6,000hr 6,000hr

Rear side Rear side

23dB(Front)

Output

power

X Monitorout X Monitorout

- R-1

HDMI R-1 HDMI R-2

In / Out terminal

Input

R-4 F-1 R-4 F-1

R-2 F-1 R-2

R-2 R-2 F-1

X L/Mono X L/Mono

TVUG TVUG

-X

Auto / Off Auto / Off

6mode 6mode

Feature

Seine + FC4 + FC6 Seine2A + Seine2D

Digital/analog SPLIT Digital Tuner/Ext SPLIT

05 OSD A 06 OSD A

3 Language 3 Language

Audio

12W + 12W 12W + 12W

2W2T 2W2T

Dby AC3 Dwnmix Dby AC3 Dwnmix

SRS/BBE Surround/BassBoost

ATSC/NTSC

Video

3DYC 3DYC

4mode 3mode

62"/360(typ),290(min) 62"/360(typ),290(min)

F / E

NTSC Tuner 1

50"/550(typ),440(min)

（100% white） 55"/455(typ),365(min) 55"/455(typ),365(min)

±37°

±7.5° ±9.1°

1st surface 1st surface

F.NO 2.67 F.NO 2.67

Screen

0.150mm 0.246mm

0.058mm 0.033mm

±32°

55",62"/ 39, 47 50",55",62"/ 36, 39, 47

Panel

EPSON LCD Panel(720P) EPSON LCD Panel (720P)

0.7" WIDE 0.7" WIDE

1284(H) x724(V) 1284(H) x724(V)

Dimension

50"/1177*812*439　

55"/1288*884*449　 55"/1288*884*449　

62"/1443*985*495　 62"/1443*985*495　

50"/1107x623mm　

55"/1218x686mm 55"/1218x686mm

62"/1373x772mm　 62"/1373x772mm

16：916：9

Remarks

Items 55/62VS69 LC57F 50/55/62VS69A LC67

LCD PTV Model name 50/55/62VS69A

Feature Specification

PREVIOUS MODEL COMPARISON TABL

LC67

7. Picture format for each input source

Aspect, Black Side Panel, Vertical Position, PIP Mode

7.1 Aspect

(1) Auto Aspect: OFF

Input Signal Aspect Mode

Format Aspect Video ID

HDMI Info

16:9

Standard

16:9

Zoom

4:3

Standard

4:3

Expanded

4:3

Zoom 1

4:3

Zoom 2

ANT Analog Video NTSC 4x3 - YES YES YES YES YES YES

16x9 - YES YES - YES - - ANT Digital YP

1080i

4x3 - - - YES YES YES YES

1080i

720p

16x9 - YES YES - YES - -

16x9 16x9

Letter Letter

4x3 4x3

480p

480i

- No information

HDMI

VGA 4x3 -

YES YES YES YES YES YES

16x9 16x9

Letter Letter

4x3 4x3

Input 1

Input 2

S-Video

Video

NTSC

- No information

YES YES YES YES YES YES

1080i

720p

16x9 - YES YES - YES - -

16x9 16x9

Letter Letter

4x3 4x3

480p

480i

- No information

YES YES YES YES YES YES

16x9 16x9

Letter Letter

4x3 4x3

Input 3

Input 4

Video

NTSC

- No information

YES YES YES YES YES YES

Input 5

Same as above

Horizontal Expansion 100% 133% 75% 100% 100% 133%

Vertical Expansion 100% 133% 100% 110% 133% 176%

(2) Auto Aspect: ON

Input Signal Aspect Mode

Format Aspect Video ID

HDMI Info

16:9

Standard

16:9

Zoom

4:3

Standard

4:3

Expanded

4:3

Zoom 1

4:3

Zoom 2

ANT Analog Video NTSC 4x3 - YES YES YES YES YES YES

16x9 - YES YES - YES - - ANT Digital YP

1080i

4x3 - - - YES YES YES YES

1080i

720p

16x9 - YES YES - YES - -

16x9 16x9 YES Initial YES - - - -

Letter Letter - - YES YES YES Initial YES

4x3 4x3 - - YES YES Initial YES YES

480p

480i

- No information YES YES YES YES YES YES

HDMI

VGA 4x3 - - - YES Initial YES YES YES

16x9 16x9 YES Initial YES - - - -

Letter Letter - - YES YES YES Initial YES

4x3 4x3 - - YES YES Initial YES YES

Input 1

Input 2

S-Video

Video

NTSC

- No information YES YES YES YES YES YES

1080i

720p

16x9 - YES YES - YES - -

16x9 16x9 YES Initial YES - - - -

Letter Letter - - YES YES YES Initial YES

4x3 4x3 - - YES YES Initial YES YES

480p

480i

- No information YES YES YES YES YES YES

16x9 16x9 YES Initial YES - - - -

Letter Letter - - YES YES YES Initial YES

4x3 4x3 - - YES YES Initial YES YES

Input 3

Input 4

Video

NTSC

- No information YES YES YES YES YES YES

Input 5 Same as above

Horizontal Expansion 100% 133% 75% 100% 100% 133%

Vertical Expansion 100% 133% 100% 110% 133% 176%

Display Specifications

LC67

(3) Expansion

4x3 Format 16x9 Format

16:9

Standard

4x3

16x9

16:9

Standard

4:3

Standard

4x3

4:3

Standard

16x9

4:3

Zoom1

16x9

75%

4:3

Zoom2

16x9

56%

75%

16:9

Zoom

16x9

75%

4:3

Expanded

4x3

90%

4x3

4:3

Zoom1

75%

4:3

Zoom2

4x3

56%

75%

4x3

16:9

Zoom

75%

4:3

Expanded

16x9

90%

1080i

720p

16x9

4:3

Expanded

90%

75%

100

110

120

130

140

150

160

170

180

0 102030405060708090100

4:3 Expanded Mode

Horizontal Position

Horizontal

Expansion

Ratio

)

113%

162%

4:3

Expanded

113%

162%

16x9

Format

100%

4x3

Format

100%

Display Specifications (cont...)

LC67

7.2 Aspect Key Operation

(1) ANT Analog Channel

(2) ANT Digital Channel

(a) Aspect: 16x9

(b) Aspect: 4x3

4:3

Zoom1

16:9

Zoom

4:3

Expanded

16:9

Standard

4:3

Zoom2

4:3

Standard

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

4:3

Zoom1

4:3

Expanded

4:3

Zoom2

4:3

Standard

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

16:9

Zoom

16:9

Standard

Aspect

Key

Aspect

Key

4:3

Expanded

Aspect

Key

(3) HDMI/YPBPR: 1080i/720p

(4) HDMI/YPBPR: 480p/480i, S-Video/Video

(4-1) Auto Aspect OFF

(4-2) Auto Aspect ON

(a)

Video ID/HDMI Info: 16x9

4:3

Zoom1

16:9

Zoom

4:3

Expanded

16:9

Standard

4:3

Zoom2

4:3

Standard

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

Video ID: 16x9

Power ON Initial

16:9

Zoom

16:9

Standard

Aspect

Key

Aspect

Key

16:9

Zoom

16:9

Standard

Aspect

Key

Aspect

Key

4:3

Expanded

Aspect

Key

Display Specifications (cont...)

LC67

(b) Video ID/HDMI Info: Letter

(d) No Video ID, No HDMI Info

4:3

Zoom2

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

4:3

Zoom1

4:3

Standard

4:3

Expanded

Video ID: Lette

Power ON Initial

4:3

Zoom1

16:9

Zoom

4:3

Expanded

16:9

Standard

4:3

Zoom2

4:3

Standard

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

Video ID: 4x3

Power ON Initial

4:3

Zoom1

4:3

Expanded

4:3

Zoom2

4:3

Standard

Aspect

Key

Aspect

Key

Aspect

Key

Aspect

Key

7.3 Vertical Position Operation

Vertical Position Input

16:9

Standard

16:9

Zoom

4:3

Standard

4:3

Expanded

4:3

Zoom 1

4:3

Zoom 2

Last

Mode

ANT Analog Video NTSC 4x3

0 step

Gray out

±10 step

(±30 lines)

±0 step

Gray out

±10 step

(±10 lines)

±10 step

(±3 lines)

±10 step

(±50 lines)

16x9 ±0 step

Gray out

±10 step

(±30 lines)

- ±10 step

(±10 lines)

- - ANT Digital YP

1080i

4x3 - - ±0 step

Gray out

±10 step

(±10 lines)

±10 step

(±30 lines)

±10 step

(±50 lines)

1080i

720p

16x9 ±0 step

Gray out

±10 step

(±30 lines)

- ±10 step

(±10 lines)

- -

480p

VGA

HDMI

480i

16x9

4x3

±0 step

Gray out

±10 step

(±30 lines)

±0 step

Gray out

±10 step

(±10 lines)

±10 step

(±30 lines)

±10 step

(±50 lines)

Input 1

S-Video

Video

NTSC 16x9

4x3

±0 step

Gray out

±10 step

(±30 lines)

±0 step

Gray out

±10 step

(±10 lines)

±10 step

(±30 lines)

±10 step

(±50 lines)

Input 2 Same as above

1080i

720p

16x9 ±0 step

Gray out

±10 step

(±30 lines)

- ±10 step

(±10 lines)

- -

480p

480i

16x9

4x3

±0 step

Gray out

±10 step

(±30 lines)

±0 step

Gray out

±10 step

(±10 lines)

±10 step

(±30 lines)

±10 step

(±50 lines)

Input 3

Video

NTSC 16x9

4x3

±0 step

Gray out

±10 step

(±30 lines)

±0 step

Gray out

±10 step

(±10 lines)

±10 step

(±30 lines)

±10 step

(±50 lines)

1080i

720p

16x9 ±0 step

Gray out

±10 step

(±30 lines)

- ±10 step

(±10 lines)

- -

480p

480i

16x9

4x3

±0 step

Gray out

±10 step

(±30 lines)

±0 step

Gray out

±10 step

(±10 lines)

±10 step

(±30 lines)

±10 step

(±50 lines)

Input 4

Video

NTSC 16x9

4x3

±0 step

Gray out

±10 step

(±30 lines)

±0 step

Gray out

±10 step

(±10 lines)

±10 step

(±30 lines)

±10 step

(±50 lines)

Input 5 Same as above

PIP Mode

SPLIT/POP/PIP

SURF/STROBE

±0 step

Gray out

7.4 Black Side Panel Operation

4:3

Standard

4:3

Standard

Gray Side

Panel

Black

Side

Black Side Panel OFF

(Power ON Initial)

Black Side Panel ON

Black Side Panel

Display Specifications (cont...)

Page is loading ...

Hitachi 62VS69A User manual

Brand: Hitachi

Model: 62VS69A

Category: TVs & monitors

Type: User manual

This manual is also suitable for

Download PDF

report

Hitachi 62VS69A User manual

This manual is also suitable for

Hitachi 62VS69A User manual

Related papers

Other documents