Danby DBC031D4BSSPR Owner's manual

Type
Owner's manual
s.01.
OWNER’S USE AND
GUIDE D’UTILISATION
ET SOIN DE PROPRI-
CAUTION
Read and follow all safety rules
and operating instructions
before first use of this product.
PRÉCAUTION
Veuillez lire attentivement les
consignes de sécurité et les
instructions d’utilisation avant
l’utilisation initiale de ce produit.
Danby Products Limited, Guelph, Ontario Canada N1H 6Z9
Danby Products Inc., Findlay, Ohio USA 45840
1-844-455-6097
CARE GUIDE
ÈTAIRE
DBC031D1BSSPR
25.09.14
Silhouette 08212014
1-844-455-609 7
DO NOT RETURN THIS UNIT TO
THE RETAILER WITHOUT FURTHER
INSTRUCTIONS
Dear Valued Customer: We hope your Silhouette appliance fullls all of your entertaining
needs. Your satisfaction is our priority. Please contact our Customer Care Center toll-free
via 1.844.455.6097 for any inquiries you may have about your new purchase.
NE PAS RETOURNER CET APPAREIL
AU DÉTAILLANT JUSQUÀ NOUVEL
ORDRE
Cher client : nous espérons que votre appareil Silhouette répond adéquatement à tous vos
besoins de divertissement. Notre priorité étant de vous satisfaire, si vous avez des questions
ou des préoccupations relativement à votre nouvelle acquisition, veuillez communiquer avec
notre Centre de service à la clientèle au numéro sans frais 1.844.455.6097.
NO DEVUELVA ESTA UNIDAD AL
VENDEDOR SIN ANTES RECIBIR
INSTRUCCIONES ADICIONALES
Estimado cliente: Esperamos que su aparato “Silhouette” pueda satisfacer todas sus
necesidades. Su satisfacción es nuestra prioridad. Por favor, póngase en contacto con
nuestro Centro de Atención al Cliente al número gratuito 1.844.455.6097, para cualquier
consulta o pregunta que usted pueda tener acerca de su nueva compra.
CONTENTS
CAUTION:
Read and follow all safety rules and operating
instructions before rst use of this product.
AVERTISSEMENT :
Veuillez lire attentivement les consignes de
sécurité et les instructions d’utilisation avant
l’utilisation initiale de ce produit.
TABLE DES MATIÈRES
BEVERAGE CENTRE
Owners Use and Care Guide...........................................................1-11
• Safety Instructions
• Before Use
• Installation Instructions
• Features
• Operating Instructions
Care and Maintenance
• Troubleshooting
• Warranty
CENTRE DE BREUVAGES
Guide d’utiliser et soin propriètaire..............................................12-22
Consignes de sécurité
• Avant l’utilisation
• Notice d’installation
• Caractéristiques
• Consinges d’utilisation
Soins et entretien
• Dépannage
• Garantie
Model • Modèle
DBC031D1BSSPR
Welcome
Note the information below; you will need this information to obtain service under warranty.
To receive service, you must provide the original receipt.
Model Number:
Serial Number:
Date of Purchase:
NEED HELP?
Before you call for service, here are a few things you can do to help
us serve you better:
Read this Owners Use and Care Guide:
It contains instructions to help you use and maintain your
appliance properly.
If you received a damaged appliance:
Immediately contact the retailer (or builder) that sold you the
appliance.
Save time and money:
Check the Troubleshooting section at the end of the guide before call-
ing. This section helps you solve common problems that may occur.
If you do need service, you can relax, knowing help is only a phone
call away.
We are proud of our quality products, and we believe in dependable service, like you will find in this Owner’s Use and Care
Guide, and like you will receive from our friendly customer service department. Best of all, you will experience these values
each and every time you use your appliance. That is important, because your new appliance will be a part of your family for
a long time.
1-844-455-6097
1
Important Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of
electrical shock by providing an escape wire for the electrical current.
ELECTRICAL REQUIREMENTS
WARNING
ELECTRICAL RATING: The serial rating plate indicates the
voltage and frequency the appliance is designed for.
To avoid installation / operation dif culties, read these instructions thoroughly.
This appliance must be grounded. Connect only to a properly grounded outlet. See “Grounding Instructions” section.
Do not operate this appliance if it has a damaged power cord or plug, if it is not working properly, or if the appliance
has been damaged or dropped.
Never allow children to operate, play with, or crawl inside the appliance.
Never clean appliance parts with ammable uids. The fumes can create a re hazard or explosion.
Do not store or use gasoline or any other ammable vapors or liquids in the vicinity of this or any other appliance.
The fumes can create a re hazard or explosion.
Do not splice the power cord that is equipped with this appliance.
Keep power cord away from heated surfaces.
Do not immerse power cord, plug or the appliance itself in water.
Do not use this product near water for example, in a wet basement, near a swimming pool or near a sink.
Do not use corrosive chemicals or vapors in this appliance.
Use this appliance only for its intended use, as described in this manual.
Store beverages in sealed containers only.
See door surface cleaning instructions in the Care and Maintenance section of this manual.
Do not cover or block any openings on the appliance.
Do not store perishable food items such as (but not limited to) meats and dairy products in your beverage centre.
This appliance is intended for household use only. Do not attempt to operate or store this appliance outdoors.
This appliance should be serviced only by quali ed service personnel. Contact the nearest authorized service facility
for examination, repair or adjustment.
IMPORTANT WARNING
An empty beverage centre is a very dangerous attraction to children. Remove either the gasket or lid
from unused appliances, or take some other action that will guarantee it harmless.
DANGER: Risk of child entrapment. Before you throw away your old beverage centre:
Take off doors.
Leave the shelves in place so that children may not easily climb in.
DON’T WAIT! DO IT NOW!
Please ensure that component parts shall be replaced with like components and that servicing shall be done by
factory authorized service personnel, so as to minimize the risk of possible ignition due to incorrect parts or
improper service.
2
GROUNDING INSTRUCTIONS
This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an
outlet that is properly installed and grounded.
This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock
by providing an escape wire for the electric current.
WARNING - Improper use of the grounding plug can result in a risk of electric shock. Consult a quali ed electrician or
service agent if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is
properly grounded.
If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
For best operation, plug this appliance into its own electrical outlet to prevent ickering of lights, blowing of fuse or trip-
ping of circuit breaker
DO NOT USE AN EXTENSION CORD
Use an exclusive 115V wall outlet. Do not connect your appliance to extension cords or together with another appliance
in the same wall outlet. Do not splice the cord. Do not under any circumstances cut or remove the third (ground) prong
from the power cord. Do not use and adapter plug with this appliance.
SAVE THESE INSTRUCTIONS!
Important Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Installation Instructions
FOR YOUR SAFETY
While performing installations described in this section, gloves and goggles or safety glasses should be worn. Two
people should be used when moving the beverage centre.
Remove interior and exterior packaging prior to installation.
Before connecting the appliance to a power source, let it stand upright for approximately 2 hours; this will reduce the
possibility of a malfunction in the cooling system from handling during transportation.
Place your beverage centre on a oor that is strong enough to support it when it is fully loaded. To level your bever-
age centre, adjust the front leveling leg at the bottom of the unit.
Locate the beverage centre away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sun-
light and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the
unit to perform improperly.
Avoid locating the unit in moist areas.
Plug the beverage centre into an exclusive, properly installed-grounded wall outlet. Do not under any circumstanc-
es cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding
should be directed toward a certi ed electrician or an authorized service centre.
Do not cover shelves with aluminum foil or any other material which may prevent air circulation.
In order for the cabinet to remain ef cient do not over load it.
Do not open the door unless necessary.
Should the beverage centre be stored without use for long periods, it is suggested, after careful cleaning, to leave the
door ajar. This will allow air to circulate inside the cabinet in order to avoid possible formations of condensation, mold
and odors.
3
LOCATION
Selecting the proper location will ensure peak performance levels for your appliance. Choose a location where the unit
will not be exposed to heat emitting sources (e.g. a replace or a barbeque). The beverage centre should not be exposed
to direct sunlight. Do not use product near water, for example in a wet basement, near a swimming pool or sink.
NOTE: This unit is front breathing. Do not
block the front air vent. Blockage of the vent
will result in high operating temperatures and
system failure.
4
LEVELING INSTRUCTIONS
Beneath the beverage centre there are two leveling legs that are located on either
side of the vent. It is important that your beverage center is level. To level the unit:
1. Move the beverage centre to its nal location.
2. Have someone gently lean against the front of the beverage center to take some
weight off the leveling legs.
3. Turn the leveling legs clockwise to raise the beverage centre or counter-clock-
wise to lower it. Continue in this manner until the beverage centre is level.
Fig A
Raises
the Leg
(lowers
the unit)
Lowers
the Leg
(raises
the unit)
Installation Instructions
PREPARING THE ENCLOSURE
Tools you will need:
While performing installations described in this section, gloves and safety glasses or goggles should be worn.
Electrical Requirements:
The appliance must be connected to an individual, properly grounded electrical outlet, protected by a 15 or 20 ampere
circuit breaker or time delay fuse.
It is recommended that you do not install the unit into a corner (i.e. directly beside a wall). This is to allow the door to
have a greater than 90° opening swing. A limited door swing may lead to damaging the door gasket, however, if it is
necessary to install the unit in a corner, be sure to allow 2-4 inches of clearance at each side.
The rough cabinet opening must be on a level oor area and at least 23 1/16” (58.6 cm) deep by 15 1/16” (38.6 cm)
wide (min). The opening should also have a height of at least 34 9/16” (86.8 cm).
The electrical outlet may be positioned from within either side of the adjacent cabinetry, or the rear of the shaded area
(as shown in Fig. 2).
If the electrical outlet is located inside the adjacent cabinetry, cut a 1-1/2” (3.81 cm) diameter hole to admit the power
cord. If the cabinet wall is metal, the hole edge must be covered with a bushing or grommet.
Tape measure
Carpenter square
Electric drill with hole bit
Gloves
Level
Safety goggles
Flashlight
Operating Instructions
FEATURES
7
5
1
3
2
6
4
5
Installation Instructions
PREPARING THE ENCLOSURE (continued)
15
1
/
16
” min
1
1
/
2
dia hole
*If electrical outlet
is in adjacent cabinetry
1
3
/
16
34
9
/
16
From underside
of countertop
to floor
6”
23
1
/16”
min
Cabinet is
square
and plumb
Electrical Access
Fig. 2
Important: The listed depth requirement for the installation is assuming that the electrical outlet is located in the adjacent
cabinetry or is ush mounted in the rear wall, not surface mounted in the enclosure.
1. Tempered Glass Door: Low-E glass, used to
re ect and absorb heat.
2. Electronic Display and Controls: For viewing
and regulating the temperature of the beverage
centre.
3. Magnetic Door Gaskets: Tight tting seals
retain all the cooling power and humidity levels.
4. Glass Shelves
5. Vertical Tower Bar Handle
6. Front Mounted Exhaust: Allows for integrated
(built-in) applications.
7. Leveling Legs
8. Interior Light (not shown): Cool White LED
lighting illuminates the interior without the heat
of an incandescent bulb.
CONTROL PANEL
6
Indicator light illuminates to signify the cooling mode is currently
in operation.
Control the interior light ON/OFF.
To turn appliance on/off (press and hold this button for approxi-
mately 3 seconds).
Used to raise (warm) the temperature by 1° increments.
Used to lower (cool) the temperature by 1° increments.
Adjacent indicator light denotes which scale of temperature is
being displayed.
°C / °F
Setting the Temperature Controls
When you plug in your beverage centre for the rst
time the temperature will automatically be set to
12°C (54°F). The default setting is °F.
Each depression of the
or
button will
allow you to adjust the temperature in 1° incre-
ments.
To switch the display between °F and °C, de-
press the
and
simultaneously for approxi-
mately 3-5 seconds.
Operating Instructions
FUNCTION INSTRUCTION
Door Ajar Alarm Function
If the door is not closed completely the alarm will sound after 5 minutes. Please close the door completely to avoid the
loss of cold energy.
Temperature Memory Function
If power is lost the set temperature will be saved by the unit. Once the power is back on the unit will return to the
same set temperature.
Temperature Alarm Function
“HI” is shown on the display panel and the alarm will sound after one hour. It is to inform you that the inner tempera-
ture is too high, please check the reason.
“LO” is shown on the display panel and the alarm will sound and the malfunction indicator light will appear at the same
time.
If too many bottles/cans are put in at once or the door has not been closed tightly, the unit will display the “HI” signal in the
display panel. This is normal, please wait 5 minutes after you close the door and “HI” will disappear.
It is normal that the cabinet shows “HI” or “LO” from time to time. If it occurs frequently or lasts for a long time, you can
restart the unit by unplugging it. If the problem occurs once again after restart, please contact customer service.
Operating Instructions
7
BEVERAGE STORAGE
In order to achieve the maximum storage capacity of sixty-six (66) cans and four
(4) bottles, it will be necessary to position the cans alternately on the upper three
glass shelves, as shown in Figure B. This will allow for the storage of twenty-two
(22) 355 ml cans per shelf in each of the top three shelves. The bottom can hold
an additional four (4) bottles (Fig. C).
IMPORTANT
The maximum* capacity of the unit is 66 (355 ml) bev-
erage cans and 4 (750 ml) bottles.
Store beverages in sealed containers only.
*When stocked as per instructions
SHELVES
To remove glass shelves:
1. Lift the back of the shelf up so the shelf pegs are above the lower rail.
2. Slide the shelf out of the unit with the pegs on the upper rail (Fig. D).
Important: Do not cover the gap on the glass shelves with aluminum foil or any
other material that will prevent adequate air circulation within the cabinet.
Fig B
Fig C
D .giF
Operating Instructions
8
DOOR REVERSAL
Fig 1A
Fig 1B
Fig 1DFig 1C
Fig 1E
1. Bottom Hinge (Right)
2. Screws
3. Door Axis
4. Screws
5. Reed Switch
6. Top Hinge (Right)
7. Screws
8. Top Hinge (Left)
9. Decorative Nail
10. Bottom Hinge (Left)
1. Open the door to a 90° angle, take out 2 screws from the lower door axis (3), remove the door (refer to Fig. 1A), then
pull out the door and door axis (Fig. 1A).
2. Put the door safely down, unscrew 2 screws (4) at the bottom and remove the Reed switch (5), then install (5) at the
top of the door frame (Fig 1A and 1B).
3. Take out 3 screws (7) from the top hinge (right) (6) and remove the right top hinge (Fig. 1C).
4. Remove the decorative nail (9) from the top left of the cabinet and install the spare top hinge (left) (8) at the top left of
the cabinet with 3 screws (Fig. 1D).
5. According to the above procedure, install the spare lower hinge (left) (10) onto the lower left cabinet (Fig. 1E).
6. Once the door has been moved, install the door the same way that it was removed and ensure the door is properly
aligned.
7. Block the hole at the top right of the cabinet with the spare decorative nail.
Please note: Do not lay the unit on its back.
Care and Maintenance
CLEANING YOUR BEVERAGE CENTRE
POWER FAILURE
Most power failures are corrected within a few hours and should not affect the temperature of your appliance if you
minimize the number of times the door is opened. If the power is going to be off for a longer period of time, you need
to take the proper steps to protect your contents.
VACATION TIME
• Short vacations: Leave the beverage centre operating during vacations of less than three (3) weeks.
• Long vacations: If the appliance will not be used for several months, remove all items and turn off the appliance.
Clean and dry the interior thoroughly. To prevent odor and mold growth, leave the door open slightly, blocking it open
if necessary.
ENERGY SAVING TIP
The unit should be located in the coolest area of the room, away from heat producing appliances, and out of direct
sunlight.
MOVING YOUR BEVERAGE CENTRE
Remove all items.
Securely tape down all loose items (shelves) inside your appliance.
Turn the adjustable leg up to the base to avoid damage.
Tape the door shut.
Be sure the appliance stays secure in the upright position during transportation. Also protect the outside of the appli-
ance with a blanket or similar item.
9
Cleaning the Inside:
• Walls, oor, inside window and shelves - Some water deposits and dust can be removed with a dry paper towel,
others may require a damp cloth.
Cleaning the Outside:
Outer Case - It is important to keep the area clean where the door seals against the cabinet. Clean this area with a
soapy cloth. Rinse with a damp cloth and let dry.
Control Panel and Door - Wipe with a damp cloth and dry thoroughly. Do not use cleaning sprays, large amounts of
soap and water, abrasive or sharp objects on the panel, they can damage it. Some paper towels may also scratch the
control panel and glass on the door.
Door Surface - Use only mild, non-abrasive detergents applied with a clean sponge or soft cloth. Rinse well with
damp cloth.
NOTE: Do not use cleaners containing ammonia or alcohol on the appliance. Ammonia or alcohol can damage the ap-
pearance of the appliance.
NOTE: Never use any commercial / abrasive cleaners or sharp objects on any part of the appliance.
Troubleshooting
Occasionally, a problem is minor and a service call may not be necessary- use this troubleshooting guide for a possible
solution. If the unit continues to operate improperly, call an authorized service depot or our Toll Free Number 1-844-455-
6097 for assistance.
PROBLEM POSSIBLE CAUSE SOLUTIONS
No power A fuse in your home may be
blown or the circuit breaker
tripped
• Power surge
Plug not fully inserted into wall
outlet
Replace fuse or reset circuit
breaker
Unplug the beverage centre, wait
a few seconds and then plug it
back in
Make sure the 3-prong plug is
fully inserted into the outlet
Cabinet temperature is too
high
Temperature is set too high
Door is not shut properly or
opened excessively
Exhaust vent is obstructed
Recently added a large quantity of
warm beverages to the cabinet
Verify the temperature control
setting, adjust if neccessary
Ensure that the door is fully
closed and that the gasket is
sealing against the cabinet. Open
the doors only as needed and for
short periods of time
Verify there is nothing blocking
the front mounted exhausting vent
Limit the quantity of warm bev-
erages being introduced to the
cabinet at the same time. Attempt
to stagger the load introduction if
possible
Alarm beeping and “HI” is
displayed on the control
panel
Recently added a large quantity
of warm bottles or cans to the
cabinet
The door is not closed tightly
System leak, evaporator fan fail-
ure or compressor fan failure
Limit the quantity of warm items
being introduced to the cabinet
Be sure the door is closed tightly
Contact a service centre, to stop
the beeping, unplug the unit
Alarm beeping and “LO”
is displayed in the control
panel
Sensor failure, evaporator tem-
perature is too low
Contact a service centre, to stop
the beeping, unplug the unit
Condensation on the cabi-
net and/or doors
High humidity conditions in the
home
Door not shut properly or opened
excessively
The condensation will subside
once humidity conditions return to
normal
Ensure that the door is fully
closed and that the gasket is seal-
ing against the cabinet. Open the
door only as needed and for short
periods of time
10
LIMITED IN-HOME APPLIANCE WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating
conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter
“Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.
First Year
During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s
option, at no charge to the ORIGINAL purchaser.
To obtain
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance
Service
requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at
their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service
must be performed by a qualied service technician.
If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all
obligations of Danby under this warranty shall be void.
Boundaries of
If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be
In Home Service
delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for
warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he
responsibility of the purchaser.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due
to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its
authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees
under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages
to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of
the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions
(extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).
Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our
AUTHORIZED SERVICE DEPOT.
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: (519) 837-0920 FAX: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: (419) 425-8627 FAX: (419) 425-8629
04/09
1-800-263-2629
Warranty Service
In-home
If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest
service center your unit must be delivered to the nearest authorized Danby Service Depot, as service
must only be performed by a technician qualified and certified for warranty service by Danby. Transpor-
tation charges to and from the service location are not protected by this warranty and are the responsi-
bility of the purchaser.
During the first twenty four (24) months, any functional parts of this product found to be defective, will be
repaired or replaced, at warrantor’s option, at no charge to the ORIGINAL purchaser.
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized
Service Depot. Any appliance requiring service outside the limited boundaries of “In Home Service” ,it
will be the consumer’s responsibility to transport the appliance (at their own expense) to the original
retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Service” below.
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby
service depot, where service must be performed by a qualified service technician. If service is performed
on the units by anyone other than an authorized service depot, or the unit is used for commercial
application, all obligations of Danby under this warranty shall be void.
First 24 months
To obtain
service
Boundaries of
in-home service
LIMITED IN-HOME APPLIANCE WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is
used under the normal operating conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or
Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other
contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or
implied, made or intended by Danby or its authorized distributors and all other warranties, conditions, representations or
guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation
or statute is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages to persons
or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit
and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for
damages to persons or property caused by the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating
conditions (extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for
outdoor application). Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event
warranty service is required, present this document to our AUTHORIZED SERVICE DEPOT.
Warranty Service
In-home
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: (519) 837-0920 FAX: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: (419) 425-8627 FAX: (419) 425-8629
1-844-455-6097
05/14
Model Modèle
For service, contact your nearest service
depot or call:
1-844-455-6097
to recommend a depot in
your area.
Pour obtenir de l’assistance, commu-
niquez avec votre centre de service le
plus rapproché ou composez le :
1-844-455-6097
pour localiser le dépositaire de votre
région
Danby Products Limited, Guelph, Ontario Canada N1H 6Z9
Danby Products Inc., Findlay, Ohio USA 45840
Printed in China
Imprimé en Chine
The model number can be found on the serial plate located on the
back panel of the unit.
All repair parts available for purchase or special order when you visit
your nearest service depot. To request service and/or the location of
the service depot nearest you, call toll free.
When requesting service or ordering parts, always provide the follow-
ing information:
3URGXFW7\SH
0RGHO1XPEHU
3DUW'HVFULSWLRQ
3DUW1XPEHU
Le numéro de modèle se trouve sur la plaque d’information sur la
paroi arrière de l’appareil.
Toutes les pièces de recharge ou commandes speciales sont
disponibles de votre centre regional de service autorise. Pour exiger le
service et-ou le nom de votre centre de service regional, signalez le
QXPpURVDQVIUDLV
Ayez les renseignements suivants à la portée de la main lors de la
commande de pièce ou service :
*HQUHGHSURGXLW
1XPpURGHPRGqOH
'HVFULSWLRQGHODSLqFH
1XPpURGHSLqFH
DBC031D1BSSPR
BEVERAGE CENTRE
CENTRE DE BREUVAGES
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26

Danby DBC031D4BSSPR Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages