Lightolier IS:26049 User manual

Brand: Lightolier

Model: IS:26049

Type: User manual

Lightolier IS:26049 is a track lighting Invisible Coupler that is used to join two pieces of track together mechanically and electrically. It can be used with the ProSpec™ Track System.

Features:

Joins two pieces of track together
Provides electrical connection between the two tracks
Concealed design
Easy to install

Benefits:

Allows for flexible track layout
Provides a secure and reliable connection
Maintains the aesthetics of the track system

Possible Use Cases:

Connecting two tracks to extend the length of the track system
Creating a corner or angle in the track layout

Lightolier IS:26049 is a track lighting Invisible Coupler that is used to join two pieces of track together mechanically and electrically. It can be used with the ProSpec™ Track System.

Features:

Joins two pieces of track together
Provides electrical connection between the two tracks
Concealed design
Easy to install

Benefits:

Allows for flexible track layout
Provides a secure and reliable connection
Maintains the aesthetics of the track system

Possible Use Cases:

Connecting two tracks to extend the length of the track system
Creating a corner or angle in the track layout

FALL RIVER, MASSACHUSETTS 02720

MONTREAL, QUEBEC, CANADA

INSTRUCTION SHEET NO.

0197 Page 1 of 1

READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY

INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC™ TRACK ITEM.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal

code specifications. To assure full compliance with codes and regulations, check with your local electrical

inspector before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

IS:26049

Installation Instructions for Invisible Coupler. For use with ProSpec

™

Track System Only.

Track Unit

Copper Wire

Contact Blade

Fig. 1

Track Unit

Fig. 2

Invisible

Coupler

Align Arrows

Fig. 4

Secured Screws

Track Unit

Bottom Cover

Secure Screws if accessible

after Track is mounted.

Spline

The Mini Coupler is used to join two pieced of track together

mechanically and electrically. Power cannot be feed into the Mini

Coupler.

Caution:

• Turn off power at fuse box before installing the invisible

coupler and track.

• Do not attempt to feed power to the invisible coupler.

INSTALLING CONNECTOR INTO TRACK SECTION

1. Remove Dead End Cover if necessary by pulling it out of Track

(save Dead End Cover). Fig 1.

2. Push Coupler into track until the arrows line up with the track

edge. Ensure that the contact blades are aligning with the copper

wires in the track during assembly. (Fig 2 & Fig 3)

3. Tighten the Locking Screw, (Fig 3)

4. Insert metal spline into the track approximately half the distance

of the metal spline length (Fig 5). Note orientation of spline in

channel.

5. Insert the assembled track and coupler into the mating track.

Ensure that the contact blades are aligning with the copper wires

in the track (Fig 2). Push together until there are no gaps between

the track unit sections. (Fig 4)

6. Check arrows on bottom of coupler. If arrows are not in line with

the edge of the track, realign the coupler until the arrows are in

line with the track edges.

7. Tighten locking screws. Note: if there is access from above the

track after it is mounted (ie. track stem installation) secure the

spline to the mating track using the (2) additional screws. Do not

use the additional two screws if there is no access. The track will

have to be removed from the structure to remove the invisible

coupler.

8. Snap the bottom cover into the track sections.

Remove Dead End

Invisible

Coupler

Track Unit

Locking Screw

Fig. 3

Fig. 5

Tighten Screws

Spline

Track Unit

Lightolier IS:26049 User manual

Brand: Lightolier

Model: IS:26049

Type: User manual

Lightolier IS:26049 is a track lighting Invisible Coupler that is used to join two pieces of track together mechanically and electrically. It can be used with the ProSpec™ Track System.

Features: