AT&T Universal Remote A10 User manual

Brand: AT&T

Model: Universal Remote A10

Category: Remote controls

Type: User manual

This manual is also suitable for

AT&T Universal Remote A10 is an advanced remote control that lets you ditch the clutter and juggle fewer remotes. Simplify your home entertainment experience with easy setup and control. Here are some of its key highlights:

Easy setup - follow the simple steps in the provided guide, and you'll be good to go in minutes
Control multiple devices - consolidate all your remotes into one to manage your TV, DVD, and AUX effortlessly
Find your remote - no more scrambling to find your remote. Press the AT&T globe button on the base station, and your remote will flash and sound an alarm
Recharge conveniently - place your remote in the base station for hassle-free charging; quick charge in 30 minutes or fully charge overnight

Easy setup - follow the simple steps in the provided guide, and you'll be good to go in minutes
Control multiple devices - consolidate all your remotes into one to manage your TV, DVD, and AUX effortlessly
Find your remote - no more scrambling to find your remote. Press the AT&T globe button on the base station, and your remote will flash and sound an alarm
Recharge conveniently - place your remote in the base station for hassle-free charging; quick charge in 30 minutes or fully charge overnight

4. How to manually program the remote

STEP 1. Power on the device you want to program

STEP 2. Locate the 4-digit code from the provided

code list.

STEP 3. Press and hold the mode key (TV, DVD, or AUX)

and while holding the mode key, press the ok key.

STEP 4. Release both the mode key and the OK key.

All the mode keys ﬂ ash but the selected

mode key stays on.

STEP 5. Enter the 4-digit code from the code list. The

selected mode key light blinks for each digit

entry and remains off after the entry of the

fourth digit

STEP 6. Point the remote control at the selected device

and press the power key once. The device

should turn off if you have found the correct

4-digit code.

STEP 7. If there are multiple codes and one does not

work, repeat steps 1-5 using the next code

until you ﬁ nd the correct one. If it still does not

work as intended, please refer to your users

manual.

TV________ DVD________ AUX________

3. How to charge the remote control

STEP 1. Place the remote control in the Base

Station.

STEP 2. Make sure that the charging points are in

full contact by seeing the charging lights

move.

NOTE: It is not necessary to charge the remote

control often, but remember to place it in

the Base Station at least one overnight

session per month if possible. Quick

charge the remote in 30 minutes or fully

charge the remote in 12 hours.

Save your codes.

5. How to use the Find Feature

STEP 1. If you have misplaced the remote

control, simply press the AT&T globe

on the Base Station (the remote control

will ﬂ ash several keys and play a ring

tone)

STEP 2. Once you have located the remote

control, press any button to stop the

sound and ﬂ ashing keys.

Charging Lights

AT&T U-verse Advanced series

A10 Remote Control

1. How to connect the Base Station

STEP 1. Determine where you would like to

place the Base Station.

STEP 2A. If the location is less than 3 feet from

the U-verse receiver, connect the

“square” end of the supplied USB cable

to the Base Station and the “rectangle”

end to the back of the U-verse receiver.

STEP 2B. If the location is more than 3 feet from

the U-verse receiver, connect one end

of the supplied plug-in power supply to

the Base Station and the other end to a

near by wall socket.

2. How to set the clock

STEP 1. Use the +H and the +M buttons on the

bottom of the Base Station to set the

hours and minutes of the clock.

STEP 2. With the remote control in the Base Sta-

-tion, press and hold the ﬁ nd button which

will cause the clock to dim as desired.

Press and hold ﬁ nd button again to make

clock brighter as desired.

Quick User Guide

AT&T Universal Remote A10 User manual

Brand: AT&T

Model: Universal Remote A10

Category: Remote controls

Type: User manual

This manual is also suitable for

Easy setup - follow the simple steps in the provided guide, and you'll be good to go in minutes
Control multiple devices - consolidate all your remotes into one to manage your TV, DVD, and AUX effortlessly
Find your remote - no more scrambling to find your remote. Press the AT&T globe button on the base station, and your remote will flash and sound an alarm
Recharge conveniently - place your remote in the base station for hassle-free charging; quick charge in 30 minutes or fully charge overnight

Download PDF

report

AT&T Universal Remote A10 User manual

This manual is also suitable for

AT&T Universal Remote A10 User manual

Related papers

Other documents