Flymo Flymo EasiLife Go 250 User manual

Brand: Flymo

Model: Flymo EasiLife Go 250

Type: User manual

This manual is also suitable for

Flymo EasiLife Go 500

Operator‘s manual

Robotic Lawn mower

EasiLife GO

Easier by Design

www.flymo.com/uk

FRONTCOVER_Flymo_EasiLife.indd 1

Contents
Introduction
1 Introduction........................................................... 3
2 Product overview...................................................4
3 Symbols on the product........................................ 5
4 Symbols on the battery......................................... 5
5 General manual instructions................................. 5
6 Keypad.................................................................. 5
7 LED status indicator on the keypad...................... 6
Safety
1 Safety information................................................. 8
2 Safety definitions...................................................9
3 Safety instructions for operation............................9
Installation
1 Introduction - Installation..................................... 12
2 Main components for installation.........................12
3 General preparations.......................................... 12
4 Before the installation of the wires...................... 12
5 Installation of the product.................................... 17
6 To put the wire into position with stakes............. 19
7 To bury the boundary wire or the guide wire.......19
8 To extend the boundary wire or the guide wire... 19
9 After the installation of the product......................20
10 To do the product settings.................................20
Operation
1 To use the ON/OFF button..................................23
2 To start the product............................................. 23
3 Operating modes.................................................23
4 To stop the product............................................. 25
5 To switch off the product..................................... 25
6 To charge the battery.......................................... 25
7 Adjust the cutting height......................................25
Maintenance
1 Introduction - maintenance..................................27
2 Clean the product................................................27
3 Replace the blades............................................. 28
4 Firmware update................................................. 28
5 Update of the Flymo EasiLife app....................... 29
6 Battery.................................................................29
7 Winter service..................................................... 30
Troubleshooting
1 Introduction - troubleshooting..............................31
2 Fault messages...................................................31
3 Information and warning messages.................... 35
4 Indicator lamp in the charging station................. 36
5 Symptoms........................................................... 37
6 Find breaks in the loop wire................................ 38
Transportation, storage and disposal
1 Transportation..................................................... 41
2 Storage................................................................41
3 Disposal.............................................................. 41
Technical data
1 Technical data.....................................................42
2 Registered trademarks........................................43
Warranty
1 Warranty terms....................................................44
EC Declaration of Conformity
1 EC Declaration of Conformity............................45
1622 - 001 - 03.03.2021

1 Introduction

1.1 Introduction

Serial number:

PIN code:

Product registration key:

The serial number is on the product carton and on the product rating plate. Refer to

Product overview on page 4

• Use the serial number to register your product on www.flymo.com/uk.

1.1.1 Support

For support about the Flymo product, speak to your

Flymo service.

1.1.2 Product description

Note: Flymo regularly updates the appearance and

function of the products. Refer to

Support on page 3

The product is a robotic lawn mower. The product has a

battery power source and cuts the grass automatically. It

continuously alternates between mowing and charging.

The movement pattern is random, which means that the

lawn is mowed evenly and with less wear. The boundary

wire and the guide wire controls the movement of the

product within the work area. Sensors in the product

senses when it is approaching the boundary wire. The

front of the product always passes the boundary wire by

a specific distance before the product turns around.

When the product hits an obstacle or approaches the

boundary wire the product selects a new direction.

The operator selects the operation settings in the Flymo

EasiLife app or with the keys on the keypad. The app

and the LED status indicator lamps show the selected

and possible operation settings, and the operation mode

of the product.

1.1.2.1 Mowing technique

The product is emission free, easy to use and saves

energy. The frequent cutting technique improves the

grass quality and decreases the use of fertilizers.

Collection of grass is not necessary.

1.1.2.2 Find the charging station

The product operates until the battery state of charge is

low. Then it follows the guide wire to the charging

station. The guide wire is laid from the charging station

towards, for instance, a remote part of the work area or

through a narrow passage. The guide wire is connected

with the boundary wire and makes it much easier and

faster for the product to find the charging station.

1.1.2.3 Flymo EasiLife app

The product can be operated with the keypad on the

product and use the factory settings of the product.

To adjust the settings of the product the Flymo EasiLife

app is used. The product can be controlled remotely with

Bluetooth

within short range.

1622 - 001 - 03.03.2021 Introduction - 3

1.2 Product overview

2021

1. ON/OFF button

2. Keypad

3. Stop button

4. Top cover

5. Body

6. Front wheels

7. Charging station

8. Contact plates

9. LED for operation check of the charging station,

boundary wire and guide wire

10. Handle

11. Chassis box with electronics, battery and motors

12. Cutting system

13. Blade disc

14. Rear wheel

15. Hex key

16. Rating plate

17. Stakes

18. Connector for the loop wire

19. Couplers for loop wire

20. Screws for securing the charging station

21. Power supply

22. Loop wire for boundary loop and guide wire

23. Measurement gauge for help when installing the

boundary wire (the measurement gauge is broken

loose from the box)

Located on the body of the product on the other side of the top cover.

The appearance may differ depending on market.

4 - Introduction 1622 - 001 - 03.03.2021

24. Low-voltage cable

25. Operator’s Manual and Quick Guide

1.3 Symbols on the product

These symbols can be found on the product. Study them

carefully.

WARNING: Read the user in-

structions before operating

the product.

WARNING: Disable the prod-

uct before working on or lift-

ing the product.

WARNING: Keep a safe dis-

tance from the product when

operating. Keep your hands

and feet away from the rotat-

ing blades.

WARNING: Do not ride on

the product. Do not put your

hands or feet close to or un-

der the product.

Use a detachable power sup-

ply as defined on the rating

plate next to the symbol.

This product conforms to the

applicable EC Directives.

It is not permitted to dispose this product

as normal household waste. Ensure that

the product is recycled in accordance with

local legal requirements.

The low-voltage cable must not be

shortened, extended or spliced.

Do not use a trimmer nearby the low-

voltage cable. Be careful when trimming

edges where the cables are placed.

1.4 Symbols on the battery

Read the user instructions.

Do not discard the battery into fire and do

not expose the battery to a heat source.

Do not immerse the battery into water.

1.5 General manual instructions

The following system is used in the Operator’s Manual

to make it easier to use:

• Text written in

italics

is a text that is shown in the

display or is a reference to another section in the

Operator’s Manual.

• Text written in bold is one of the buttons on the

product.

1.6 Keypad

Use the keypad on the product to select an operating

mode for the product. Push the button for 1 second or 3

seconds to set an operating mode, refer to

Operating

modes on page 23

. The buttons on the keypad with

flashing lights are the available operating modes for the

product that you can select. You must enter the PIN

code for the product before you can select an operating

mode.

• Use the ON/OFF button (A) to switch on and

switch off the product.

• Use the Park button (B) to send the product to the

charging station.

• Use the OK button (C) to confirm the settings you

select in the menus.

• Use the GO/Schedule button (D) to start the

product and set a schedule. The schedule will start

at this current time each day and the product will

operate to its maximum cutting time each day.

• Use the GO button (E) to start the operation of the

product.

1622 - 001 - 03.03.2021

Introduction - 5

B D

1.7 LED status indicator on the keypad

The LED status indicator on the keypad shows the status of the product. There are 2 light modes on the LED status

indicator, flashing light (A) and solid light (B).

Standby Idle

6 - Introduction 1622 - 001 - 03.03.2021

Waiting for PIN code Wrong PIN code

Cutting according to set

Schedule

Cutting, either in operating mode

Override schedule

Secondary area

Parked

Error

1622 - 001 - 03.03.2021 Introduction - 7

2 Safety

2.1 Safety information

2.1.1 IMPORTANT. READ CAREFULLY

BEFORE USE. KEEP FOR FUTURE

REFERENCE

The operator is responsible for accidents or hazards occurring to

other people or property.

This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities (that

could affect a safe handling of the product), or lack of experience

and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person

responsible for their safety.

This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Local regulations

may restrict the age of the operator. Cleaning and maintenance

shall not be made by children without supervision.

Never connect the power supply to an outlet if the plug or cord is

damaged. Worn or damaged cord increase the risk of electric

shock.

Only charge the battery in the included charging station. Incorrect

use may result in electric shock, overheating or leaking of

corrosive liquid from the battery. In the event of leakage of

electrolyte, flush with water/neutralizing agent. Seek medical help if

it comes in contact with the eyes.

Use only original batteries recommended by the manufacturer.

Product safety cannot be guaranteed with other than original

batteries. Do not use non-rechargeable batteries.

- Safety 1622 - 001 - 03.03.2021

The appliance must be disconnected from the supply mains when

removing the battery.

WARNING: The product

can be dangerous if used

incorrectly.

WARNING: Do not use

the product when

persons, especially

children, or animals are

in the work area.

WARNING: Keep your

hands and feet away

from the rotating blades.

Never put your hands or

feet close to or under the

product when it is

switched on.

WARNING: In the event

of an injury or accident

seek medical help.

2.2 Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING:

Used if there is a risk of

injury or death for the operator or bystanders

if the instructions in the manual are not

obeyed.

CAUTION: Used if there is a risk of

damage to the product, other materials or

the adjacent area if the instructions in the

manual are not obeyed.

Note: Used to give more information that is necessary

in a given situation.

2.3 Safety instructions for operation

2.3.1 Use

• The product may only be used with the equipment

recommended by the manufacturer. All other types

of use are incorrect. The manufacturer’s

instructions with regard to operation/maintenance

must be followed precisely.

• Warning signs shall be placed around the work

area of the product if it is used in public areas. The

signs shall have the following text: Warning!

Automatic lawnmower! Keep away from the

machine! Supervise children!

Warning!

Automatic lawnmower!

Keep away from the machine!

Supervise children!

Warning!

Automatic lawnmower!

Keep away from the machine!

Supervise children!

• Use the park mode, refer to

Park on page 24

switch off the product when persons, especially

children, or animals are in the work area. It is

recommended to program the product for use

during hours when the area is free from activity.

Refer to

Park / Schedule on page 24

. Consider

that certain animals, e.g. hedgehogs, are active at

night. They can potentially be harmed by the

product.

• Do not install the charging station, including any

accessory, at a location that is below, or within 60

cm / 24 in. from, any combustible material. Do not

install the power supply unit in easily flammable

surroundings. In case of malfunction, heating of

the charging station and the power supply may

occur and create a potential risk of fire.

1622 - 001 - 03.03.2021

Safety - 9

• The product may only be operated, maintained and

repaired by persons that are fully conversant with

its special characteristics and safety regulations.

Please read the Operator’s Manual carefully and

make sure you understand the instructions before

using the product.

• It is not permitted to modify the original design of

the product. All modifications are made at your

own risk.

• Check that there are no foreign objects such as

stones, branches, tools or toys on the lawn. If the

blades hit foreign objects the blades can be

damaged. Always switch off the product with the

ON/OFF button before clearing a blockage. Inspect

the product for damage before staring the product

again.

• If the product starts to vibrate abnormally. Always

switch off the product with the ON/OFF button and

inspect for damage before staring the product

again.

• Start the product according to the instructions.

When the product is switched on, make sure to

keep your hands and feet away from the rotating

blades. Never put your hands and feet under the

product.

• Never touch moving hazardous parts, such as the

blade disc, before it has come to a complete stop.

• Never lift up the product or carry it around when it

is switched on.

• Do not let persons who do not know how the

product works and behaves use it.

• The product must never be allowed to collide with

persons or other living creatures. If a person or

other living creature comes in the product’s way it

shall be stopped immediately. Refer to

To stop the

product on page 25

• Do not put anything on top of the product or its

charging station.

• Do not allow the product to be used with a

defective guard, blade disc or body. Neither should

it be used with defective blades, screws, nuts or

cables. Never connect a damaged cable, or touch

a damaged cable before it is disconnected from

the supply.

• Do not use the product if the ON/OFF button and

STOP button does not work.

• Always switch off the product using the ON/OFF

button when the product is not in use. The product

can only start when the product has been switched

on with the ON/OFF button and the correct PIN

code has been entered.

• Flymo does not guarantee full compatibility

between the product and other types of wireless

systems such as remote controls, radio

transmitters, hearing loops, underground electric

animal fencing or similar.

• Metal objects in the ground (for example reinforced

concrete or anti-mole nets) can result in a

stoppage. The metal objects can cause

interference with the loop signal which then can

lead to a stoppage.

• Operation and storage temperature range is 0-50

°C / 32-122 °F. Temperature range for charging is

0-45 °C / 32-113 °F. Too high temperatures might

cause damage to the product.

2.3.2 Battery safety

WARNING: Lithium-ion batteries can

explode or cause fire if disassembled, short-

circuited, exposed to water, fire, or high

temperatures. Handle carefully, do not

dismantle, open the battery or use any type

of electrical/mechanical abuse. Avoid

storage in direct sunlight.

For more information about the battery, refer to

Battery

on page 29

2.3.3 How to lift and move the product

WARNING:

The product must be

switched off before lifting it. The product is

disabled when the indicator lamp on the

ON/OFF button is not lit.

CAUTION: Do not lift the product when

it is parked in the charging station. It can

damage the charging station and/or the

product. Push STOP and pull the product

out of the charging station before lifting it.

To safely move from or within the work area:

1. Push the STOP button to stop the product.

- Safety 1622 - 001 - 03.03.2021

2. Push the ON/OFF button for 3 seconds to switch

off the product.

3. Make sure that the product is disabled. The

indicator lamp on the ON/OFF button is not lit

when the product is disabled. Refer to

LED status

indicator on the keypad on page 6

4. Carry the product by the handle with the blade disc

away from your body.

2.3.4 Maintenance

WARNING: The product must be

switched off before maintenance is done.

The product is disabled when the indicator

lamp on the ON/OFF button is not lit.

WARNING: Use the plug to disconnect

the charging station before cleaning or

maintenance of the charging station or the

loop wire.

CAUTION: Do not use a high-pressure

washer to clean the product. Do not use

solvents for cleaning.

Examine the product weekly and replace damaged or

worn parts. Refer to

Maintenance on page 27

2.3.5 In the event of a thunderstorm

To reduce the risk of damage to electrical components

in the product and the charging station, we recommend

that all connections to the charging station are

disconnected (power supply, boundary wire and guide

wire) if there is a risk of a thunderstorm.

1. Mark the wires to simplify reconnecting. The

charging station’s connections are marked R, L

and GUIDE.

2. Disconnect all connected wires and the power

supply.

3. Connect all the wires and the power supply if there

is no longer a risk of thunder. It is important that

each wire is connected to the right place.

1622 - 001 - 03.03.2021

Safety - 11

3 Installation

3.1 Introduction - Installation

Refer to www.flymo.com/uk for more information about

installation and instruction videos.

We recommend you to update the firmware before you

install the product to make sure that the product has the

latest firmware. Refer to

Firmware update on page 28

WARNING: Read and understand the

safety chapter before you install the product.

CAUTION: Use original spare parts and

installation material.

3.2 Main components for installation

The installation involves the following components:

• A robotic lawn mower that mows the lawn

automatically.

• A charging station, which has 3 functions:

• To send control signals along the boundary

wire.

• To send control signals along the guide wire

so that the product can follow the guide to

specific remote areas in the garden and can

find its way back to the charging station.

• To charge the product.

• A power supply, which is connected to the

charging station and a 100-240V power outlet.

• Loop wire, which is laid around the work area and

around objects and plants that the product must

not run into. The loop wire is used both as

boundary wire and guide wire.

3.3 General preparations

CAUTION: Holes with water in the lawn

can cause damage to the product.

Note: Read through the Installation chapter before

beginning the installation. How the installation is done

affects how the product performs. It is therefore

important to plan the installation carefully.

• Make a blueprint of the work area and include all

obstacles. This makes it easier to see the ideal

positions for the charging station, the boundary

wire and the guide wire.

• Make a mark on the blueprint where to put the

charging station, the boundary wire and the guide

wire.

• Make a mark on the blueprint where the guide wire

connects to the boundary wire. Refer to

To install

the guide wire on page 18

• Fill in holes in the lawn.

• Cut the grass before you install the product. Make

sure that the grass is maximum 4 cm / 1.6 in.

Note: The first weeks after installation the perceived

sound level when cutting the grass may be higher than

expected. When the product has cut the grass for some

time, the perceived sound level is much lower.

3.4 Before the installation of the wires

You can select to attach the wires with stakes or bury

them. You can use the 2 procedures for the same work

area.

CAUTION: If you use a dethatcher in

the work area, bury the boundary wire and

the guide wire to prevent them from

damage.

3.4.1 To examine where to put the charging

station

• Keep a minimum 2 m / 6.6 ft. of free space in front

of the charging station. Refer to

To examine where

to put the guide wire on page 16

• Keep a minimum of 30 cm / 12 in. of free space to

the right and left of the center of the charging

station.

60- cm / 24- in.

• Put the charging station near a power outlet.

• Put the charging station on a level surface.

• The baseplate of the charging station must not be

bent.

- Installation 1622 - 001 - 03.03.2021

Max 3 cm/1.2"

Max +/- 2 cm / 0.8 in.

• If the work area has two parts separated with a

steep slope, we recommend to put the charging

station in the lower section.

• Put the charging station in an area with protection

from the sun.

• If the charging station is installed on an island,

make sure to connect the guide wire to the island.

Refer to

To make an island on page 15

3.4.2 To examine where to put the power

supply

WARNING:

Do not cut or extend the

low-voltage cable. There is a risk of

electrical shock.

CAUTION: Make sure that the blades

on the product do not cut the low-voltage

cable.

CAUTION: Do not put the low-voltage

cable in a coil or below the charging station

plate. The coil causes interference with the

signal from the charging station.

• Put the power supply in an area with a roof and

protection from the sun and rain.

• Put the power supply in an area with good airflow.

• Use a residual-current device (RCD) with a tripping

current of maximum 30 mA when you connect the

power supply to the power outlet.

Low-voltage cables of different lengths are available as

accessories.

3.4.3 To examine where to put the

boundary wire

CAUTION: There must be a barrier of

minimum 15 cm / 6 in. in height between the

boundary wire and water bodies, slopes,

precipices or public roads. This will prevent

damage to the product.

CAUTION: Do not let the product

operate on gravel.

CAUTION: Do not make sharp bends

when you install the boundary wire.

CAUTION: For careful operation

without noise, isolate all obstacles such as

trees, roots and stones.

The boundary wire should be put as a loop around the

work area. Sensors in the product senses when the

product approaches the boundary wire, and the product

selects another direction. All parts of the work area must

be maximum 15 m / 50 ft. from the boundary wire.

To make the connection easier between the guide wire

and the boundary wire, it is recommended to make an

eyelet where the guide wire will be connected. Make the

1622 - 001 - 03.03.2021

Installation - 13

eyelet with approximately 20 cm / 8 in. of the boundary

wire.

Note: Make a blueprint of the work area before you

install the boundary wire and guide wire.

• Put the boundary wire around all of the work area

(A). Adapt the distance between the boundary wire

and obstacles.

• Put the boundary wire 35 cm / 14 in. (B) from an

obstacle that is more than 3.5 cm / 1.4 in. high.

35 cm /14

> 3.5 cm / 1.4

• Put the boundary wire 30 cm / 12 in. (C) from an

obstacle that is 1-3.5 cm / 0.4-1.4 in. high.

1-3.5 cm / 0.4-1.4"

30 cm / 12"

• Put the boundary wire 10 cm / 4 in. (D) from an

obstacle that is less than 1 cm / 0.4 in. high.

10 cm / 4"

max 1 cm / 0.4"

• If you have a paving stone path that is in level with

the lawn, put the boundary wire below the paving

stone.

Note:

If the paving stone is minimum 30 cm / 12

in. wide, use the factory setting for the

Drive Past

Wire

function to cut all the grass adjacent to the

paving stone. Refer to

Drive Past Wire function on

page 21

• If you make an island, put the boundary wire that

runs to and from the island near together (E). Put

the wires in the same stake. Refer to

To make an

island on page 15

• Make an eyelet (F) where the guide wire is to be

connected to the boundary wire.

- Installation 1622 - 001 - 03.03.2021

3.4.3.1 To put the boundary wire in a slope

The product can operate in 25% slopes. Slopes that are

too steep must be isolated with the boundary wire. The

gradient (%) is calculated as height per m. Example: 10

cm / 100 cm = 10%.

10 cm/ 4"

100 cm/ 40"

10%

• For slopes steeper than 25% inside the work area,

isolate the slope with boundary wire.

• For slopes steeper than 10% along the outer edge

of the lawn, put the boundary wire 20 cm / 8 in. (A)

from the edge.

>10%

0-25%

• For slopes adjacent to a public road, put a barrier

of minimum 15 cm / 6 in. along the outer edge of

the slope. You can use a wall or a fence as a

barrier.

3.4.3.2 Passages

A passage is a section that has boundary wire on each

side and that connects 2 parts of the work area. The

distance between the boundary wire on each side in the

passage must be a minimum of 60 cm / 24 in.

Note:

If a passage is less than 2 m / 6.5 ft. wide,

install a guide wire through the passage.

The recommended minimum distance between the

guide wire and the boundary wire is 30 cm / 12 in. The

product always runs to the left of the guide wire as seen

facing the charging station. It is recommended to have

as much free area as possible to the left of the guide

wire (A).

>1 m / 3.3 ft

>30 cm / 12"

>60 cm / 24"

3.4.3.3 To make an island

CAUTION: Do not put a section of

boundary wire across the other. The

sections of boundary wire must be parallel.

CAUTION: Do not put the guide wire

across the boundary wire.

CAUTION: Isolate or remove obstacles

that are less than 15 cm / 5.9 in. in height.

Isolate or remove obstacles that slope

slightly, for example, stones, trees or roots.

This will prevent damage to the blades of

the product.

To make an island, isolate areas in the work area with

the boundary wire. We recommend to isolate all stable

objects in the work area.

1622 - 001 - 03.03.2021

Installation - 15

Some obstacles are resistant to a collision, for example,

trees or bushes that are more than 15 cm / 5.9 in. in

height. The product will collide with the obstacle and

then select a new direction.

• Put the boundary wire to and around the obstacle

to make an island.

• Put the 2 sections of boundary wire to and from the

island close together. This will make the product

run across the wire.

• Put the 2 sections of boundary wire in the same

stake.

0 cm / 0

3.4.3.4 To make a secondary area

Make a secondary area (B) if the work area has 2 areas

that are not connected with a passage. The work area

with the charging station is the main area (A).

Note:

The product must be manually moved between

the main area and the secondary area.

• Put the boundary wire around the secondary area

(B) to make an island. Refer to

To make an island

on page 15

Note:

The boundary wire must be put as 1 loop

around all of the work area (A + B).

Note: When the product cuts grass in the

secondary area, the

Secondary area

mode must

be selected. Refer to

Secondary area on page

3.4.4 To examine where to put the guide

wire

Put the guide wire from the charging station through the

work area and connect it to the boundary wire.

C E

• Put the guide wire in a line at a minimum of 1 m /

3.3 ft. in front of the charging station (A).

• Put the guide wire minimum 30 cm / 1 ft. from the

boundary wire (B).

• Starting point (C). Refer to

Starting point on page

• Minimum distance 60 cm / 2 ft. perpendicular to the

guide wire (D).

• Where the guide wire is connected to the boundary

wire (E).

• Guide corridor (F). The product always runs to the

left of the guide wire as seen facing the charging

station. Make sure that the guide wire has as much

free area as possible to the left of the guide wire.

The guide corridor can be maximum 1.2 m / 4 ft.

Note:

The product always runs in the guide

corridor but changes the distance to the guide

wire.

3.4.5 Work area examples

• If the charging station is put in a small area (A),

make sure that the distance to the boundary wire is

at a minimum 2 m / 6.6 ft. in front of the charging

station.

- Installation 1622 - 001 - 03.03.2021

• If the work area has a passage (B) with no guide

wire installed, the minimum distance between the

boundary wires is 2 m / 6.5 ft. With a guide wire

installed through the passage, the minimum

distance between the boundary wires is 60 cm / 24

in. Use the

PassageSense

function to cut this

passage, Refer to

Lawn Coverage and

PassageSense on page 21

• If the work area has areas which are connected by

a narrow passage (B), you can set the product to

first follow and then leave the guide wire after a

certain distance (C). The settings can be changed

Lawn Coverage and PassageSense on page

• If the work area includes a secondary area (D),

refer to

Secondary area on page 24

. Put the

product in the secondary area and select

Secondary area mode

3.5 Installation of the product

3.5.1 Installation tools

• Hammer/plastic mallet: To simplify putting the

stakes into the ground.

• Edge cutter/straight spade: To bury the boundary

wire.

• Combination pliers: For cutting the boundary wire

and pressing the connectors together.

• Adjustable plier: For pressing the couplers

together.

3.5.2 To install the charging station

WARNING: Obey national regulations

about electrical safety.

WARNING: The product is only to be

used with the power supply unit supplied by

Flymo.

WARNING: Do not put the power

supply at a height where there is a risk it can

be put in water. Do not put the power supply

on the ground.

WARNING: Do not encapsulate the

power supply. Condensed water can harm

the power supply and increase the risk of

electrical shock.

WARNING: Risk of Electric Shock.

Install only to a residual-current device

(RCD) with a tripping current of maximum 30

mA when connecting the power supply to

the power outlet. Applicable to USA/Canada.

If power supply is installed outdoors: Risk of

Electric Shock. Install only to a covered

Class A GFCI receptacle (RCD) that has an

enclosure that is weatherproof with the

attachment plug cap inserted or removed.

CAUTION: Do not make new holes in

the charging station plate.

CAUTION: Do not put your feet on the

baseplate of the charging station.

WARNING: The power supply cable

and extension cable must be outside the

work area to avoid damage to the cables.

When connecting the power supply, only use a power

outlet that is connected to a residual-current device

(RCD).

1. Read and understand the instructions about where

to put the charging station. Refer to

To examine

where to put the charging station on page 12

2. Put the charging station in the selected area.

1622 - 001 - 03.03.2021

Installation - 17

Note: Do not attach the charging station with the

screws to the ground until the guide wire is

installed. Refer to

To install the guide wire on page

3. Connect the low-voltage cable to the charging

station.

4. Put the power supply at a minimum height of 30

cm / 12 in.

min 30 cm / 12”

5. Connect the power supply cable to a 100-240V

power outlet.

Note: When the charging station is connected, it

is possible to charge the product. Put the product

in the charging station while the boundary and

guide wires are being laid. Switch on the product to

start charging the product. Refer to

To use the

ON/OFF button on page 23

. Do not continue with

any product settings before the installation is

complete.

6. Put the low-voltage cable in the ground with stakes

or bury the cable. Refer to

To put the wire into

position with stakes on page 19

To bury the

boundary wire or the guide wire on page 19

7. Connect the wires to the charging station after the

installation of boundary wire and guide wire is

complete. Refer to

To install the boundary wire on

page 18

and

To install the guide wire on page

8. Attach the charging station to the ground with the

supplied screws after the guide wire is installed.

Refer to

To install the guide wire on page 18

3.5.3 To install the boundary wire

CAUTION:

Do not put remaining wire in

a coil. The coil causes interference with the

product.

1. Put the boundary wire around all of the work area.

Start and complete the installation behind the

charging station.

2. Open the connector and put the boundary wire in

the connector.

3. Close the connector with a pair of pliers.

4. Cut the boundary wire 1-2 cm / 0.4-0.8 in. above

each connector.

5. Push the right connector onto the metal pin on the

charging station with the mark "R".

6. Push the left connector onto the metal pin on the

charging station with the mark "L".

3.5.4 To install the guide wire

CAUTION: Twinned cables, or a screw

terminal block that is insulated with

insulation tape are not satisfactory splices.

Soil moisture will cause the wire to oxidize

and after a time result in a broken circuit.

1. Open the connector and put the wire in the

connector.

2. Close the connector with a pair of pliers.

3. Cut the guide wire 1-2 cm / 0.4-0.8 in. above each

connector.

4. Push the guide wire through the slot in the

charging station plate.

5. Push the connector onto the metal pin on the

charging station with the mark "G".

6. Disconnect the charging station from the power

outlet.

7. Put the end of the guide wire at the eyelet on the

boundary wire.

8. Cut the boundary wire with a pair of wire cutters.

9. Connect the guide wire to the boundary wire with a

coupler.

- Installation 1622 - 001 - 03.03.2021

a) Put the 2 ends of the boundary wire and the

end of the guide wire into the coupler.

Note: Make sure that you can see the ends

of the wires through the transparent area of

the coupler.

b) Push down the cover on the coupler with

adjustable pliers to attach the wires in the

coupler.

10. Attach the guide wire to the ground with stakes or

bury the guide wire in the ground. Refer to

To put

the wire into position with stakes on page 19

To bury the boundary wire or the guide wire on

page 19

11. Connect the charging station to the power outlet.

3.6 To put the wire into position with

stakes

CAUTION:

Make sure that the stakes

hold the boundary wire and the guide wire

against the ground.

CAUTION: Cutting the grass too low

right after installation can damage the wire

insulation. Damage to the insulation may not

cause disruptions until several weeks or

months later.

1. Put the boundary wire and the guide wire on the

ground.

2. Put the stakes at a maximum of 100 cm / 40 in.

distance from each other.

3. Attach the stakes to the ground with a hammer or

a plastic mallet.

Note: The wire is overgrown with grass and not visible

after a few weeks.

3.7 To bury the boundary wire or the

guide wire

• Cut a groove in the ground with an edge cutter or a

straight shovel.

• Put the boundary wire or the guide wire 1-20 cm /

0.4-8 in. into the ground.

3.8 To extend the boundary wire or the

guide wire

Note: Extend the boundary wire or the guide wire if it

is too short for the work area. Use original spare parts,

for example couplers.

1. Disconnect the charging station from the power

outlet.

2. Cut the boundary wire or the guide wire with a pair

of wire cutters where it is necessary to install the

extension.

3. Add wire where it is necessary to install the

extension.

4. Put the boundary wire or the guide wire into

position.

5. Put the wire ends into a coupler.

Note:

Make sure that you can see the ends of

the boundary wire or the guide wire through the

transparent area of the coupler.

6. Push down the cover on the coupler with

adjustable pliers to attach the wires in the coupler.

1622 - 001 - 03.03.2021

Installation - 19

7. Put the boundary wire or the guide wire into

position with stakes.

8. Connect the charging station to the power outlet.

3.9 After the installation of the product

3.9.1 To do a visual check of the charging

station

1. Make sure that the indicator LED lamp on the

charging station has a green light.

2. If the indicator LED lamp does not have a green

light, do a check of the installation. Refer to

Indicator lamp in the charging station on page 36

and

To install the charging station on page 17

3.10 To do the product settings

Use the Flymo EasiLife app to set all the settings for the

product. The functions have factory settings that are

applicable for almost all work areas, but the settings can

be adapted to the conditions for each work area.

3.10.1 To download and pair with the Flymo

EasiLife app

The Flymo EasiLife app is a free app for your mobile

device. The Flymo EasiLife app is used for the settings

and operation of the product. The short-range interaction

with the product is called Bluetooth

. When pairing

between the product and app has been confirmed, you

have access to the menus and functions as long as you

are within short-range (Bluetooth

1. Download the Flymo EasiLife app on your mobile

device.

2. Switch off the product and switch it on again.

3. Pair the Flymo EasiLife app with the product.

Note: The Bluetooth

pairing mode is active for

3 minutes.

4. Enter the PIN code. Refer to

PIN code on page

3.10.2 To do the Schedule settings

You can set the schedule in 3 different procedures:

• Use the Flymo assisted scheduling where you

enter the size of your work area and the

scheduling wizard shows an applicable schedule.

• Use the Manual scheduling to set or adjust the

schedule manually.

• Use the GO/Schedule button to set a daily

schedule that starts this current time each day and

the product will operate to its maximum cutting

time each day. Refer to

To set the product to

operate in Main area and make a daily schedule

on page 23

CAUTION: Do not cut the lawn more

than it is necessary to prevent wear on the

product and the lawn.

3.10.2.1 Make an estimate of the necessary operating

time

If the work area is less than maximum product capacity,

the schedule must be set to decrease the wear on the

lawn and the product. The product has a maximum

cutting time each day. You can set the operating time of

the product in the schedule. The operating time includes

cutting, searching and charging. The operating time can

be different because of many reasons, for example the

layout of the work area, the grass growth and age of the

battery. When the product has operated to the maximum

cutting time in a day, the message

Today's mowing

complete

is shown in the display of the app.

The recommended operating times for some work area

examples are shown in the table below. If the result is

not satisfactory, increase the operating time.

Area, m

Recommended operating

time, h

250 4-5

500 10-11

20 - Installation 1622 - 001 - 03.03.2021

Page is loading ...

Flymo Flymo EasiLife Go 250 User manual

Brand: Flymo

Model: Flymo EasiLife Go 250

Type: User manual

This manual is also suitable for

Flymo EasiLife Go 500

Download PDF

report

Flymo Flymo EasiLife Go 250 User manual

This manual is also suitable for

Flymo Flymo EasiLife Go 250 User manual

Related papers

Other documents