Moog Videolarm MR5CS-3 Product Instructions

Brand: Moog Videolarm

Model: MR5CS-3

Type: Product Instructions

This manual is also suitable for

HOUSING INSTALLATION:

1. Carefully remove all equipment from the box.

2. Cut a 7.75" diameter hole in the ceiling in the desired

location.

3. Twist the trim ring and remove it from the housing.

4. Run power and video/control connections through the

opening on the side of the housing (Figure 1).

Figure 1

Wiring access

hole

TABLE OF CONTENTS

1noitpircseD

2snoitac

icepS lacirtcelE

Installing the Housing Assembly 1

2trahC edoC roloC gniriW

Setting Protocol for the Unit 3

Setting the Address for the Unit 3

4sgnitteS nevirD uneM

6sgnitteS hctiwspiD

Safeguards and Warranty Information 7

DESCRIPTION:

MR5CS-9 is Recessed Drop Ceiling Housing with Videolarm

S-view pan/tilt. Upper housing is constructed of 20 and 18

gauge steel, while the lower dome is formed from optically

clear polycarbonate (1 F-stop light reduction for tinted lower

dome). The housing can be installed in its entirety from

below the ceiling. The steel top measures 5.5” (h) x 7.5”

(d). The lower dome will be held in place by a white plastic

trim ring. The MR5CS-9 is designed to be installed in either

sheetrock or drop ceilings. The (2) spring clips allow for

adjustment to the ceiling material thickness.

STANDARD INSTALLATION PROCEDURE

INCLUDES MODELS: MR5CS-9 / MR5TS-9

Figure 2

Add wire

supports

around clips

in drop ceiling

applications

PRODUCT INSTRUCTIONS

REVISION DATE:

02-03-2009

SPECIFICATION NUMBER: 5363

MODEL: MR5CS-9

250

120

400

180

141

600

300

225

130

112

960

480

358

225

179

143

119

102

800

571

350

285

228

190

163

140

126

114

103

1300

905

525

452

362

301

258

215

201

181

164

150

139

129

120

113

106

100

1440

830

720

576

480

411

340

320

288

261

240

221

205

192

180

169

160

151

144

5.5

100

110

120

130

140

150

160

170

180

190

200

Maximum distance from transformer to load

Total vA

consumed

Wire Gauge

24k VAC Wiring Distances

The following are the recommended maximum distances for 24 VAC

with a 10% voltage drop (10% is generally the maximum allowable

voltage drop for AC powered devices).

Wiring Color Code

Power and Control Inputs

ANALOG

POWER

1 Camera Power (24 VAC) Red

2 Camera Power (24 VAC) Orange

CONTROL (not used for Network)

eulBAXR584-SR1

teloiVBXR584-SR2

yarGAXT584-SR3

etihWBXT584-SR4

NETWORK (IP)

POWER

1 Camera Power (24 VAC) Red

2 Camera Power (24 VAC) Orange

ALARM (Network)

eulBGND1

teloiVGND2

yarGAlarm OUT3

etihWAlarm IN4

Check the supplied wiring chart to be sure that

you have the proper gauge wire for the distance

that you intend to run your power wires.

5. Insert the housing into the ceiling. The spring clips will

depress as it goes into the opening, then ex back to

allow the housing to rest against the inside of the ceiling

(Figure 2).

6. Complete wiring - per wiring diagrams.

7. Install pan/tilt per Figure 3. Insert two pins into pan/tilt

base. Press other end down and secure captive bolt.

8. Complete installation by re-install dome and trim ring

assembly.

Figure 3

- 2 -

Factory Settings

DO NOT ADJUST

PC Board

located here

SETTING THE ADDRESS FOR THE UNIT

Each pan/tilt must have its own unique address. The factory

default address is 001 . To change this address use the 8 position

dip switch located on the PC Board on the side of the pan/tilt (Figure

4), referring to the chart in the back of this manual. The address is

set with the rocker style dip switches, which are non-volatile. The

address cannot be changed unless the dip switches are moved, or

unless the Remote Address feature in the VLC485 software is used.

Address

Dip Switches

SETTING PROTOCOL FOR THE UNIT

There are no user settings for protocol selection. The S View 2™ will

respond to Pelco D, Pelco P, or Videolarm VL422 protocol automati-

cally (1 start bit, 1 stop bit, 8 data bits, no parity).

NETWORK INSTALLATION

In addition to the video server serial number, you will also need an IP

address. This address should be obtained from your network system

administrator.

Pages 9 through 12 of the SView Network Video Server Administra-

tion (SNVS Admin) Manual describe how to set up the IP address.

Choose the method most appropriate for your system

CONFIGURING THE VIDEO SERVER

Pages 13 to 27 of the SNVS Admin Manual describe how to con-

¿JXUHWKHYLGHRVHUYHU7KHUHDUH:L]DUGVDYDLODEOHEXWZHGRQRW

recommend that they be used as we have experienced some prob-

lems with them. Instead, perform the following steps using the SNVS

Admin Manual and the online help system as a reference.

• Start a browser and enter the IP address of the dome into the

ORFDWLRQDGGUHVV¿HOG7KH$;,62(09LGHR6HUYHUZLQGRZ

should open up.

• Click on the ADMIN button.

Pan/Tilt Setup

Your camera system should come with the proper settings for pan

DQGWLOWDOUHDG\FRQ¿JXUHG7KHLQVWUXFWLRQVEHORZVKRXOGRQO\EH

QHHGHGLI\RXQHHGWRUHFRQ¿JXUHWKHXQLWDIWHUUHVWRULQJWKHIDFWRU\

defaults.

• Click on the COM1 icon. Note: COM1 selects the RS-485 port,

&20VHOHFWVWKH56SRUW<RXUFDPHUDV\VWHPLVFRQ¿JXUHG

for RS-485.

• Under purpose, select “Pan Tilt”

• Click on the “Pan Tilt” icon. Under Driver for Pan Tilt set the driver

to PelcoDD5-C. Click Save. A dialog box will tell you that you

need to restart the server. Click OK.

• Click on the COM1 icon. Make sure the settings are 9600 Baud,

eight (8) data bits, one (1) stop bit, and Parity None. Click Save.

• Click on the Video icon. Under Pan Tilt Serial Port, select COM1

– Pelco DD5-C.

 &OLFNRQ³'ULYHU6SHFL¿F6HWWLQJV´LFRQ,GHQWLI\WKHFDPHUDDVWKH

address assigned at the pan/tilt unit via the DIP switch.

• The picture speed is the maximum speed that the camera will

move when you click in the picture. Picture time is how long the

motion will last before stopping. The move speed and time control

WKHHTXLYDOHQWVHWWLQJVZKHQWKHDUURZEXWWRQVDUHXVHG:H

have found the following values reasonable: Picture Speed 63,

Picture Time 100, Move Speed 63, Move time 80. This allows

ODUJHPRYHPHQWVXVLQJWKHDUURZFRQWUROVDQG¿QHDGMXVWPHQWV

by clicking inside the picture. Zoom and focus time control how

long the command is applied. A Zoom of 1000 and Focus of 2000

was reasonable. Iris speed is not used as the iris is controlled by

discrete steps. Click Apply then Close.

Appearance and Presets

• Click on image settings. Set up a date/time display or text caption

WKDWZLOOEHGLVSOD\HGZLWKWKHFDPHUDSLFWXUHLIGHVLUHG$GMXVW

the resolution and compression based on the network bandwidth

limitations and picture quality needed. Click OK.

• Click on Preset Positions. For each preset desired, use the pan,

WLOWDQG]RRPFRQWUROVWRSRVLWLRQWKHFDPHUDHQWHULQDQDPHIRU

the preset and press Save. You may also save one of the presets

DVD+RPHSRVLWLRQZKLFKLVQDPHGKRPH:KHQDOOWKHSUH-

sets have been saved, click on Close.

• Click on Video Server. Date and time allow you to set the current

WLPHDQGWLPH]RQH6HFXULW\DOORZV\RXWRDGGXVHUVDQGVHWSDVV-

words. Layout controls the look of the video server page. If you

click on Factory Default it will wipe out all the work that you have

done so far, so only use it if you really want to start over.

• For use of the Network page, refer to the SNVS Admin Manual.

Video Server Operation

5HIHUWRWKH6196$GPLQ0DQXDOIRU9LGHR6HUYHUVSHFL¿FIXQFWLRQV

Camera System Operation

To operate the camera system from your browser, click on View Ap-

plication. The arrow keys provide the ability to pan, tilt or both. The

FHQWHU+NH\ZLOOJRWRWKH+RPH3UHVHWLIWKHUHLVRQH7KH]RRP

and focus bars are proportional to how far from the center that you

click. The Iris will close or open one step each time the bar is clicked.

The AUTO buttons next to the Focus and Iris bars are not currently

functional.

Day/Night Camera

:KHQWKHOLJKWOHYHOLVORZWKHFDPHUDZLOOVZLWFKRXWWKHLQIUDUHG¿OWHU

and go to black and white mode. This feature can be permanently

turned off, on, or set to automatic mode by using the menu in the On

Screen Display.

Zones

7KHUHDUH]RQHVWKDWPD\EHSURJUDPPHGLQWKH69LHZ(DFK

]RQHPD\EHVHWDVDSULYDF\]RQHZLWKWKHYLGHRRII7KH]RQHWLWOHLI

programmed and enabled, will be displayed regardless of whether the

]RQHLVSURJUDPPHGIRUSULYDF\RUQRW

IMPORTANT NOTE: You will need the serial number of the video

VHUYHUIRUXVHDVWKH(WKHUQHW0$&DGGUHVV

This address is located on a label inside the

GRPHDVZHOODVRQWKHVKLSSLQJODEHO:ULWHLW

down for use in the network installation.

- 3 -

Presets

The SView 2 has 64 presets that can be used individually or as part of

an autotour. You can move to a preset by dropping down the preset

box and clicking on the desired preset. The camera will move rapidly

WRWKHSDQWLOWDQG]RRPSRVLWLRQGH¿QHGE\WKHSUHVHW

Presets are stored by going into the Admin functions, selecting Video

DQG¿QDOO\3UHVHW3RVLWLRQV)LUVWSRVLWLRQWKHFDPHUDWRWKHGHVLUHG

location using the Pan, Tilt and Zoom controls. Then place the cur-

sor in the “Current Position” box and type a descriptive name for the

position. Press “Save” when the name is correct. Repeat for each

preset desired.

7KHUHDUHWZRSUHVHWVZLWKSUHVH¿QHGIXQFWLRQV7KH¿UVWSUHVHWLV

used to select autotour. The second preset will select the camera

system menus.

Preset Numbering

7KH¿UVWSUHVHWWKDWLVHQWHUHGE\WKHXVHUIROORZLQJ0HQXZLOOFRU-

respond to Preset 4 in the PTZ. The next will be 5, etc. Care must be

taken when removing presets as you may leave a gap in the numbering

sequence. (See the section on Autotour above.) If you always remove

presets starting with the last one, the gaps will not occur.

Autotour

The Autotour function causes the camera to automatically go, in se-

quence, to each preset that has been programmed into the PTZ. The

dwell time at each preset position can be individually set to be from 0

to 99 seconds. See the Menu Driven Settings section to learn how to

set dwell time. The Autotour will continue until a pan or tilt command is

given. If the unit loses power while in Autotour, Autotour will be resumed

when power is restored.

Note that when a preset is removed via the Admin functions, it is not

actually deleted from the PTZ unit. Therefore once a preset has been

GH¿QHGLWZLOOFRQWLQXHWREHYLVLWHGGXULQJ$XWRWRXUHYHQLILWLVUHPRYHG

,IWKHODVWSUHVHWLVUHPRYHGDQGWKHQDQRWKHULVGH¿QHGLWZLOOUHSODFH

that preset in the PTZ. However, if you remove a preset that is not the

ODVWSUHVHWWKHQGH¿QHDQHZRQHLWPD\DGGDQHZSUHVHWWRWKH37=

rather than replace the previous one.

Controlling the dwell time during Autotuors is done via the menu functions.

See the Menu Driven Settings for the operation of this feature.

Restoring Autotour and Menu presets

If the Autotour and/or Menu preset is accidentally removed, the following

steps can be used to restore them.

Under Admin, select the Video icon then the “Preset Positions” icon.

From the “Preset positions:” drop down box, select each preset one at

DWLPHWKHQSUHVVWKH5HPRYHEXWWRQ:KHQWKHRQO\HQWU\OHIWLV³1RQH´

all the presets have been removed. Now go to the “Current position:”

box, type “Autotour” and press Save. Then type “Menu” and press save.

You should now see “None”, “Autotour”, and “Menu” in the drop down

boxes. Select “Menu” in the “Goto preset position” drop down box and

press Go to verify that these presets have been entered correctly. You

may then set up the desired PTZ preset positions.

Accessing the Dome Menus

The Menu function provides access to additional dome functions includ-

LQJRQVFUHHQWH[W&DPHUDDGMXVWPHQW]RQHVGZHOOWLPHVDQGV\VWHP

LQIRUPDWLRQ:KHQWKH0HQXIXQFWLRQLVVHOHFWHGWKHVFUHHQEODQNV

and 0000 is displayed on the bottom left of the screen. The up/down

controls change the current digit and the right/left controls move from

digit to digit. The password to access the menus is 6387. The password

is examined when selecting pan left at digit one or pan right at digit 4.

If the password is correct, the menus will be displayed. If the password

is incorrect, the dome will return to normal operation.

$WDQ\SRLQWLQWKHPHQXV\VWHPLIQRLQSXWSDQWLOW]RRPLVUHFHLYHG

for 30 seconds, the dome will exit the menus and return to normal

operation.

MENU DRIVEN SETTINGS

:KHQ\RXDUHLQWKH0DLQ0HQXSDQDQGWLOWIXQFWLRQVZLOOQRWFRQWURO

the motion of the pan/tilt (except where noted). Instead, “Tilt Up” or

“Tilt Down” will be used to navigate up or down along the main menu.

"Pan Right” and “Pan Left” will be used to select between the main

menu selection and the sub menu. The “Zoom In” and “Zoom Out”

are used to turn the selected functions on or off.

DISPLAY - This controls the display of the compass heading and

allows the user to calibrate the compass heading. PAN RIGHT to

DFFHVVWKHVXEPHQX7,/7'2:1WRDFFHVVHDFKLWHP3$1/()7

to return to the main menu.

COMPASS - The display show “COMPASS ON” or “COMPASS

2))´3UHVV³]RRPLQ´WRWXUQWKHFRPSDVVKHDGLQJRQDQG³]RRP

out’ to turn the compass display off.

SET NORTH3UHVV³]RRPLQ´EXWWRQWRVHWFDOLEUDWLRQ7KH

display will show “OK”.

POSITION - This displays the pan and tilt positions of the camera.

3UHVV]RRPLQWRWXUQWKLVRQ]RRPRXWWRWXUQLWRII

ADDRESS7KLVGLVSOD\VWKHFDPHUDDGGUHVV3UHVV]RRPLQWR

WXUQWKLVRQ]RRPRXWWRWXUQLWRII

TEMP - This displays the temperature sensor data on the tilt

ERDUG3UHVV]RRPLQWRWXUQWKLVRQ]RRPRXWWRWXUQLWRII

NOTE: This reading will be higher than the actual ambient

temperature in the dome. This is for diagnostic use only.

PRESSURE - This displays the pressure sensor data for units

HTXLSSHGZLWKDSUHVVXUHVHQVRU3UHVV]RRPLQWRWXUQWKLVRQ

]RRPRXWWRWXUQLWRII

- 4 -

SHOW$OORZVWKHWLWOHWREHGLVSOD\HG3UHVV]RRPLQWR

WXUQWKLVRQ]RRPRXWWRWXUQLWRII

PRIVATE'HWHUPLQHVLIWKLVZLOOEHDSULYDF\]RQH3UHVV]RRP

LQWRWXUQWKLVRQ]RRPRXWWRWXUQLWRII

RLIMIT6HWVWKHSDQULJKWOLPLWIRUWKH]RQH7KHFXUUHQWSDQ

OLPLWZLOOEHGLVSOD\HG3UHVV]RRPRXWWKHSLFWXUHZLOOUHDSSHDU

and you will have pan control. Pan to the desired location. Press

]RRPLQWRVHOHFW7KHQHZSDQOLPLWZLOODSSHDU

LLIMIT6HWVWKHSDQOHIWOLPLWIRUWKH]RQH7KHFXUUHQWSDQOLPLW

ZLOOEHGLVSOD\HG3UHVV]RRPRXWWKHSLFWXUHZLOOUHDSSHDUDQG

you will have pan control. Pan to the desired location. Press

]RRPLQWRVHOHFW7KHQHZSDQOLPLWZLOODSSHDU

NOTE: The picture will displayed whenever you are in RLIMIT

or LLIMIT. When you toggle to any other sub-menu the

picture will disappear.

CAMERA - 7KH³&$0(5$´VXEPHQXLVXVHGWRFRQWUROVHYHUDORI

the camera’s parameters. PAN RIGHT to access the sub-menu. TILT

'2:1WRDFFHVVHDFKLWHP

NOTE: :KHQWKLVVXEPHQXLVDFFHVVHGWKHFDPHUDSLFWXUHZLOO

UHWXUQWRDOORZDGMXVWPHQWV

STABILIZER6WDELOL]HUZKHUHHTXLSSHGFRPSHQVDWHVIRUVPDOO

PRYHPHQWVRUYLEUDWLRQVZKHQWKHFDPHUDLV³]RRPHGLQ´3UHVV

]RRPLQWRWXUQWKLVRQ]RRPRXWWRWXUQLWRII

DAY/NIGHT - This is used to control the low light mode of the

camera. There are three choices:

AUTO - The camera will automatically switch into day/night

mode for low light conditions.

DAY - The camera will be in the day mode continuously.

NIGHT - The camera will be in the night mode continuously.

3UHVV]RRPLQWRF\FOHWKURXJKWKHFKRLFHV3

SHUTTER - Selects between auto and manual shutter speeds.

3UHVV]RRPLQWRF\FOHXSWKURXJKWKHVHOHFWLRQVRU]RRPRXW

to cycle down.

BACKLIGHT&RQWUROVEDFNOLJKWFRPSHQVDWLRQ3UHVV]RRPLQ

WRWXUQWKLVRQ]RRPRXWWRWXUQLWRII

AGC - Selects automatic AGC or minimum AGC (0db). Press

]RRPLQWRWXUQWKLVRQ]RRPRXWWRWXUQLWRII

DIGI ZOOM7XUQVWKHGLJLWDO]RRPRQDQGRII3UHVV]RRPLQ

WRWXUQWKLVRQ]RRPRXWWRWXUQLWRII

ALARM - 7RJHWWRWKLVVHFWLRQWLOWGRZQIURPWKH&$0(5$PHQX

This menu allows the user to control the operation of the alarm input.

,IWKHDODUPLVHQDEOHGWKHFDPHUDZLOOJRWRSUHVHW3UHVV]RRP

LQWRHQDEOHSUHVV]RRPRXWWRGLVDEOH

ZONES - 8SWR]RQHVPD\EHVHOHFWHGHDFK]RQHKDVDQXPEHU

RISDUDPHWHUVDVVRFLDWHGZLWKLW3DQ5LJKWWRDFFHVV=RQHV=21(

1" will display.

7LOWXSRU7LOWGRZQWRVHOHFWWKH]RQHGHVLUHG2QFHWKH]RQHLV

selected, "Pan Right" to access the sub-menu.

TITLE - Displays the current title.

SET TITLE7KLVLVXVHGWRVHWWKHWLWOHRIWKH]RQH7KHFXUUHQW

]RQHWLWOHZLOOEHGLVSOD\HGDWWKHERWWRPRIWKHVFUHHQZLWKDW

question mark (?) at the cursor position. Use pan right or left to

FKDQJHWKHFXUVRUSRVLWLRQ:KHQWKHGHVLUHGSRVLWLRQKDVEHHQ

selected, use tilt up and tilt down to select the character to be

GLVSOD\HG3UHVV]RRPLQWRVHWWKHWLWOHDQGH[LWWKHVXEPHQX

3UHVVLQJ]RRPRXWZLOOUHVWRUHWKHRULJLQDOWLWOH

SYSTEM INFO - Displays the Pan Version, Tilt Version, Current Pan

Position and Current Tilt Position.

PRESETS - Allows the selection of the dwell times for each of the 64

SUHVHWV:KHQWKLVVXEPHQXLVVHOHFWHGWKHGZHOOWLPHIRUHDFKRI

the 64 presets is displayed.

NOTE: If a preset has not been saved, the dwell time for that

preset will only be displayed as ".."

REMINDER: A dwell time of more than "0" can only be selected if

a preset has been saved.

Press "tilt up" or "tilt down" to select the desired preset.

Pan right and the dwell time selection will appear. Press "tilt up"

or "tilt down" to change the time.

- 5 -

Pan left to return to the Presets Selection sub-menu. Pan left

again to return to the Main Menu.

OTHER FEATURES:

Error Messages

7KH³&200(5525´PHVVDJHZLOOEHGLVSOD\HGDWWKHWRSRIWKH

screen whenever the S View 2™ detects frame errors in the receive

GDWDVXFKDVZKHQWKH5;$DQG5;%ZLUHVDUHUHYHUVHGZKHQXVLQJ

RS485/422 or when the baud rate is incorrect.

7KH³&$0(5$(5525´PHVVDJHZLOOEHGLVSOD\HGDWWKHWRSRIWKH

screen whenever there is an error in communicating with the camera.

DIPSWITCH SETTINGS:

Address Dip switch settings, refer to Table 1 on next page.

EXIT - Pan left to exit the Main Menu.

Table 1: Pan/Tilt Address Dip Switch Settings

ADDRESS SW8 SW7 SW6 SW5 SW4 SW3 SW2 SW1

0 OFF OFF OFF OFF OFF OFF OFF OFF

1 OFF OFF OFF OFF OFF OFF OFF ON

2 OFF OFF OFF OFF OFF OFF ON OFF

3 OFF OFF OFF OFF OFF OFF ON ON

4 OFF OFF OFF OFF OFF ON OFF OFF

5 OFF OFF OFF OFF OFF ON OFF ON

6 OFF OFF OFF OFF OFF ON ON OFF

7 OFF OFF OFF OFF OFF ON ON ON

8 OFF OFF OFF OFF ON OFF OFF OFF

9 OFF OFF OFF OFF ON OFF OFF ON

10 OFF OFF OFF OFF ON OFF ON OFF

11 OFF OFF OFF OFF ON OFF ON ON

12 OFF OFF OFF OFF ON ON OFF OFF

13 OFF OFF OFF OFF ON ON OFF ON

14 OFF OFF OFF OFF ON ON ON OFF

15 OFF OFF OFF OFF ON ON ON ON

16 OFF OFF OFF ON OFF OFF OFF OFF

17 OFF OFF OFF ON OFF OFF OFF ON

18 OFF OFF OFF ON OFF OFF ON OFF

19 OFF OFF OFF ON OFF OFF ON ON

20 OFF OFF OFF ON OFF ON OFF OFF

21 OFF OFF OFF ON OFF ON OFF ON

22 OFF OFF OFF ON OFF ON ON OFF

23 OFF OFF OFF ON OFF ON ON ON

24 OFF OFF OFF ON ON OFF OFF OFF

25 OFF OFF OFF ON ON OFF OFF ON

26 OFF OFF OFF ON ON OFF ON OFF

27 OFF OFF OFF ON ON OFF ON ON

28 OFF OFF OFF ON ON ON OFF OFF

29 OFF OFF OFF ON ON ON OFF ON

30 OFF OFF OFF ON ON ON ON OFF

31 OFF OFF OFF ON ON ON ON ON

32 OFF OFF ON OFF OFF OFF OFF OFF

33 OFF OFF ON OFF OFF OFF OFF ON

34 OFF OFF ON OFF OFF OFF ON OFF

35 OFF OFF ON OFF OFF OFF ON ON

36 OFF OFF ON OFF OFF ON OFF OFF

37 OFF OFF ON OFF OFF ON OFF ON

38 OFF OFF ON OFF OFF ON ON OFF

39 OFF OFF ON OFF OFF ON ON ON

40 OFF OFF ON OFF ON OFF OFF OFF

41 OFF OFF ON OFF ON OFF OFF ON

42 OFF OFF ON OFF ON OFF ON OFF

43 OFF OFF ON OFF ON OFF ON ON

44 OFF OFF ON OFF ON ON OFF OFF

45 OFF OFF ON OFF ON ON OFF ON

46 OFF OFF ON OFF ON ON ON OFF

47 OFF OFF ON OFF ON ON ON ON

48 OFF OFF ON ON OFF OFF OFF OFF

- 6 -

CAUTION

RISK OF

ELECTRIC SHOCK!

CAUTION: TO REDUCE THE RISK OF

ELECTRICAL SHOCK, DO NOT EXPOSE

COMPONENTS TO WATER OR MOISTURE.

SAFETY PRECAUTIONSIMPORTANT SAFEGUARDS

1. Read Instructions - All the safety and operating instructions should be read

before the unit is operated.

2. Retain Instructions - The safety and operating instructions should be retained

for future reference.

3. Heed Warnings - All warnings on the unit and in the operating instructions

should be adhered to.

4. Follow Instructions - All operating & user instructions should be followed.

5. Electrical Connections - Only a qualiﬁed electrician should make electrical

connections.

6. Attachments - Do not use attachments not recommended by the product

manufacturer as they may cause hazards.

7. Cable Runs - All cable runs must be within permissible distance.

8. Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining

the weight of the unit. Accordingly:

a. Installation should be made by a qualiﬁed installer.

b. Installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to install the unit,

taking into account both the composition of the mounting surface and

the weight of the unit. Be sure to periodically examine the unit and the

supporting structure to make sure that the integrity of the installation

is intact. Failure to comply with the foregoing could result in the unit

separating from the support structure and falling, with resultant damages

or injury to anyone or anything struck by the falling unit.

UNPACKING

Unpack carefully. Electronic components can be damaged if improperly handled

or dropped. If an item appears to

have been damaged in shipment, replace it

properly in its carton and notify the shipper. Be sure to save:

1. The shipping carton and packaging material. They are the safest material in

which to make future shipments of the equipment.

2. These Installation and Operating Instructions.

The lightning ﬂash with an arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of non-insulated "dangerous voltage" within the

product's enclosure that may be of sufﬁcient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to presence of important operating

and maintenance (servicing) instructions in the literature

accompanying the appliance.

24 HOUR TECHNICAL SUPPORT

1-800-554-1124

SERVICE

If the unit ever needs repair service, customer should contact Videolarm

(1-800-554-1124) for return authorization & shipping instructions.

TECHNICAL SUPPORT

Videolarm has set-up a 24 hour technical support line for their customers.

LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS

VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship, as follows:

PRODUCT CATEGORY PARTS LABOR

All Enclosures and Electronics Five (5) Years Five (5) Years

Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan

Poles/PoleEvators Three (3) Years Three (3) Years

Warrior/Q-View/I.R. Illuminators Five (5) Years Five (5) Years

Controllers Five (5) Years Five (5) Years

Power Supplies Five (5) Years Five (5) Years

Accesso

ry Brackets Five (5) Years Five (5) Years

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Videolarm Inc. Decatur GA.

The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with a RMA # (Return Materials

Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support Team at 800.554.1124, extension 101.

Videolarm will return the repaired Product freight prepaid to Purchaser. Videolarm is not obligated to provide Purchaser with a substitute unit during the warranty

period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or parts charges.

The limi

ted warranty stated in these product instructions is subject to all of the following terms and conditions:

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice

with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the warranty period.

If after investigation Videolarm determines that the reported problem was not covered by the warranty, Purchaser shall pay Videolarm for the cost of investigating

the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period as to the entire

Product. The speciﬁc warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part

or the

remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair

any Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during

the warranty period which is subjected to any of the following: abuse, improper use: negligence, accident, lightning damage or other acts of God (i.e., hurricanes,

earthquakes), modiﬁcation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to foll

ow the maintenance

procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the Product.

Furthermore, Videolarm shall have no liability where a schedule is speciﬁed for regular replacement or maintenance or cleaning of certain parts (based on usage)

and the end-user has failed to follow such schedule; attempted repair by non-qualiﬁed personnel; operation of the Product outside of the published environmental

and electrical parameters, or if such Product’s original identiﬁcation (trademark, serial number) markings have been defaced, altered, or removed. Videolarm

excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser.

All software and accompanying documentation furnished with, or as part of the Product

is furnished “AS IS” (i.e., without any warranty of any kind), except where

expressly provided otherwise in any documentation or license agreement furnished with the Product.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH REGARD TO ANY CLAIM

OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. VIDEOLARM HEREBY DISCLAIMS

ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-VIDEOLARM PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS

PURCHASER CHOOSES TO CONNECT TO PRODUCT.

LIMITATION OF LIABILITY THE LIABILITY OF VIDEOLARM, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER,

REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH

SUCH CLAIM IS MADE. IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT

LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

/ tour operation

**6 months if used in autoscan

/ tour operation

**6 months if used in autoscan

/ tour operation

SView Series Five (5) Years Five (5) Years