Whalen ATBK-P2-US / SC-ATBK User manual

Brand
Whalen
Model
ATBK-P2-US / SC-ATBK
Category
TV stands
Type
User manual
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Mfg., Inc. Page 1 Factory No. 70-14295
Astoria Bookcase
Model # ATBK-P2
ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS,
SHARP POINTS, SHARP EDGES AS RECEIVED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to
the store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our website 24 hours a day, 7 days a week for product assistance at:
www.whalenfurniture.com
Or e-mail your request to parts@whalenfurniture.com
LOT NUMBER:
DATE PURCHASED: / /
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 2 Factory No. 70-14295
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will
repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture
product is designed to meet your highest expectations. We guarantee that you will immediately
see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary
from State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m. PST, Monday to Friday
WWW.WHALENFURNITURE.COM
MANUFACTURER: Whalen Furniture
CATALOG: Astoria Bookcase (ATBK-P2)
DATE OF MANUFACTURE: January 2012
MADE IN CHINA
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH PRODUCTS HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 80 lb. (36.3 kg)
MAXIMUM RECOMMENDED WEIGHT LOADS
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 3 Factory No. 70-14295
Parts and Hardware List
Please read completely through the instructions and verify that all parts listed are present before
beginning assembly.
A- Top Wood Frame (1) B- Middle Wood Frame (1)
C- Bottom Wood Frame (1) D- Top Back Stretcher (1)
E- Left Wood Leg (1) F- Right Wood Leg (1)
G- Top Long Metal Support (2) H- Top Short Metal Support (2)
I- Bottom Left Metal Support (1) J- Bottom Right Metal Support (1)
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 4 Factory No. 70-14295
Parts and Hardware List
Please read completely through the instructions and verify that all parts listed are present before
beginning assembly.
K- Front Bottom Metal Support (2) L- Metal Bar (2)
M- Top Glass (1) N- Glass Shelf (2)
(1) 3/4” Bolt (4+1 extra) (2) 1-1/4” Bolt (19+1 extra) (3) 1-3/4” Bolt (4+1 extra)
(4) Small Bolt (4+1 extra) (5) Lock Washer (27+1 extra) (6) Flat Washer (27+1 extra)
(7) Wood Dowel Allen Wrench Touch-up Pen Tipping Restraint Hardware Kit (2)
(2+1 extra) (2) (1) (Inside Plastic Bag)
Tools required: Allen Wrench (provided) and Phillips Screwdriver (not provided).
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 5 Factory No. 70-14295
Assembly Instructions
Note: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make it easier during assembly of unit.
1. Unpack the unit and confirm that you have all the hardware and required parts listed.
2. Insert 2 Wood Dowels (7) all the way into the end holes on Top Back Stretcher (D).
3. Using the dowels as a guide, align and attach the Top Back Stretcher (D) to Top Wood Frame (A)
using three 1-1/4” Bolts (2) with Washers (5 & 6) through the cleat holes into the threaded inserts
included on the Top Wood Frame. See detail #1.
Required hardware in this step
‘
Description: (2) 1-1/4” Bolt (5) Lock Washer (6) Flat Washer (7) Wood Dowel
Sketch
Qty. (3 pcs) (3 pcs) (3 pcs) (2 pcs)
Tools required: Allen Wrench
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 6 Factory No. 70-14295
Assembly Instructions
4. Align & attach Top Metal Supports (G & H) onto the Wood Top Frame (A) as shown in detail #2.
Make sure that the metal bracket on the top of each Top Metal Support points toward the Top Back
Stretcher (D). Insert and screw 3/4" Bolts (1) with the Washers (5 & 6) through the metal bracket of
the Top Metal Supports and loosely tighten into the threaded inserts on the Wood Top Frame (A).
Required hardware in this step
Description: (1) 3/4” Bolt (5) Lock Washer (6) Flat Washer
Sketch
Qty. (4 pcs) (4 pcs) (4 pcs)
Tools required: Allen Wrench
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 7 Factory No. 70-14295
Assembly Instructions
5. Align and attach Left and Right Wood Legs (E & F) to the Top Back Stretcher (D) making sure the
thru holes of Wood Legs align with the sockets of the Top Metal Supports (G & H) properly. Insert
and screw four 1-1/4” Bolts (2) with Washers (5 & 6) through the pre-drilled holes on Top Back
Stretcher (D) and loosely into the threaded inserts on the Wood Legs (E & F). Make sure the threaded
inserts on the side of the Wood Legs is facing inside. See detail #3.
Required hardware in this step
‘
Description: (2) 1-1/4” Bolt (5) Lock Washer (6) Flat Washer
Sketch
Qty. (4 pcs) (4 pcs) (4 pcs)
Tools required: Allen Wrench
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 8 Factory No. 70-14295
Assembly Instructions
6. Pick up one Front Bottom Metal Support (K) and attach onto the Right Wood Leg (F) by inserting
one 1-3/4” Bolt (3) with Washers (5 & 6) through the metal bracket of the Bottom Metal Support
though the Right Wood Leg and loosely tighten into the sockets on the Top Long Metal Support (G).
See detail #4. Make sure that the top edges of the Front Bottom Metal Support and Right Wood Leg
are even with each other.
7. Proceed to attach Bottom Right Metal Support (J) onto the Right Wood Leg (F) by using one 1-3/4”
Bolt (3) with Washers (5 & 6). Make sure the threaded inserts on the side of Bottom Right Metal
Support facing inside and the top edges are even with each other. DO NOT tighten the bolt in this
step. See detail #4.
8. Repeat last two steps to attach the other Front Bottom Metal Support (K) and Bottom Left Metal
Support (I) onto the Left Wood Leg (E).
Required hardware in this step
‘
Description: (3) 1-3/4” Bolt (5) Lock Washer (6) Flat Washer
Sketch
Qty. (4 pcs) (4 pcs) (4 pcs)
Tools required: Allen Wrench
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 9 Factory No. 70-14295
Assembly Instructions
9. Fit the Middle Wood Frame (B) between the Wood Legs (E & F) and Bottom Metal Supports (I & J)
ensuring the pre-drilled holes on both cleats align with the threaded inserts properly and back edge of
Middle Wood Frame is even with the Top Back Stretcher (D). Attach the Middle Wood Frame in
place by using four 1-1/4” Bolts (2) with Washers (5 & 6) through the pre-drilled holes on cleats. See
detail #5.
Required hardware in this step
‘
Description: (2) 1-1/4” Bolt (5) Lock Washer (6) Flat Washer
Sketch
Qty. (4 pcs) (4 pcs) (4 pcs)
Tools required: Allen Wrench
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 10 Factory No. 70-14295
Assembly Instructions
10. Align and attach Bottom Wood Frame (C) to the top of last assembly by inserting the 1-1/4” Bolts (2)
with Washers (5 & 6) through the countersunk holes on the Bottom Wood Frame into the Legs.
Tighten the bolts with the Allen Wrench provided. See detail #6.
Required hardware in this step
‘
Description: (2) 1-1/4” Bolt (5) Lock Washer (6) Flat Washer
Sketch
Qty. (8 pcs) (8 pcs) (8 pcs)
Tools required: Allen Wrench
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 11 Factory No. 70-14295
Assembly Instructions
11. Align and attach 2 Metal Bars (L) between the Wood Bottom Frame (C) and the Top Back Stretcher
(D) for extra support using the Small Bolts (4) and tighten with Phillips Screwdriver. See detail #7.
12. Go back and securely tighten all bolts with the Allen Wrench provided.
Required hardware in this step
‘
Description: (4) Small Bolt
Sketch
Qty. (4 pcs)
Tools required: Phillips Screwdriver
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 12 Factory No. 70-14295
Assembly Instructions
13. Carefully flip around the unit upright.
14. Place Top Glass (M) and Glass Shelves (N) onto the grooves on the Wood Fames respectively as
shown in detail #8. Make sure the black side of glass is down.
Note: If glass is scratched you can minimize the damage by using a BLACK marker and
filling in scratched area from underneath.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
If the glass is chipped or broken, stop using the product and consult the manufacturer or supplier.
1) Do not place very hot or very cold items on the glass surface(s) unless adequately thick
tablemats are used to prevent such items from coming into contact with the glass.
2) Do not sit or stand upon the glass surface(s).
3) Do not use the glass as a chopping surface. Do not strike the glass with hard or pointed items.
4) When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap
if necessary; do not use washing powders or any other substances containing abrasive since
these substances scratch glass.
Model # ATBK-P2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 13 Factory No. 70-14295
TIPPING RESTRAINT HARDWAR
Note: We have included two Tipping Restraint Hardware bags for this unit. You must install this hardware to
prevent accidents or injuries from falling unit.
When properly installed, this restraint can provide protection against the unexpected tipping of the unit due
to small tremors, bumps or climbing. We strongly recommend mounting this hardware to a wall stud and
your unit.
Please carefully read the instructions printed on the bag.
Note: You must install the Tipping Restraint Hardware with the unit in use to prevent any accidents or
damage to the unit.
Tools required: Phillips Screwdriver, Mallet, Power Drill, 3/8” Drill Bit
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
Using solvents of any kind on your furniture may damage your furniture’s finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
Stains or marks from crayons or ink markers will be difficult to remove.
In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
Check bolts/screws periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate controlled environment. Extreme temperature and humidity
changes can cause warping, shrinking and splitting of wood. It is advised to keep furniture away from direct
sunlight as may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and
helpful tips will enhance your furniture as it ages.
A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
Allen Wrench
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Whalen ATBK-P2-US / SC-ATBK User manual

Brand
Whalen
Model
ATBK-P2-US / SC-ATBK
Category
TV stands
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents