Samsung SCC-C6435P/TRK User manual

User’s Guide

SCC-C6433(P)/C6435(P)

SmartDome Camera

ENG RUS POL

2

3

This symbol indicates that dangerous

voltage consisting a risk of electric

shock is present within this unit.

This symbol indicates that there are

important operating and maintenance

instructions in the literature

accompanying this unit.

WARNING

•

To reduce the risk of re or electric shock, do

not expose this appliance to rain or moisture.

•

WARNING

1.

Be sure to use only the standard adapter

that is specied in the specication sheet.

Using any other adapter could cause re,

electrical shock, or damage to the product.

2.

Incorrectly connecting the power supply or

replacing battery may cause explosion, re,

electric shock, or damage to the product.

3.

Do not connect multiple cameras to a single

adapter. Exceeding the capacity may cause

abnormal heat generation or re.

4. Securely plug the power cord into the

power receptacle. Insecure connection

may cause re.

5. When installing the camera, fasten it

securely and rmly. A falling camera may

cause personal injury.

6.

Do not place conductive objects (e.g.

screwdrivers, coins, metal things, etc.) or

containers lled with water on top of the

camera. Doing so may cause personal injury

due to re, electric shock, or falling objects.

7. Do not install the unit in humid, dusty, or

sooty locations. Doing so may cause re

or electric shock.

8. If any unusual smells or smoke come

from the unit, stop using the product. In

such case, immediately disconnect the

power source and contact the service

centre. Continued use

in such a condition may cause re or

electric shock.

Safety Precautions

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

2

ENG

3

9. If this product fails to operate normally,

contact the nearest service centre. Never

disassemble or modify this product

in any way. (SAMSUNG is not liable

for problems caused by unauthorized

modications or attempted repair.)

10. When cleaning, do not spray water

directly onto parts of the product. Doing

so may cause re or electric shock.

CAUTION

1. Do not drop objects on the product or

apply strong shock to it. Keep away from

a location subject to excessive vibration

or magnetic interference.

2. Do not install in a location subject to

high temperature (over 122°F), low

temperature (below 14°F), or high

humidity. Doing so may cause re or

electric shock.

3. If you want to relocate the already

installed product, be sure to turn off the

power and then move or reinstall it.

4. Remove the power plug from the outlet

when then there is a lightning.

Neglecting to do so may cause re or

damage to the product.

5. Keep out of direct sunlight and heat

radiation sources. It may cause re.

6. Install it in a place with good ventilation.

7. Avoid aiming the camera directly towards

extremely bright objects such as sun,

as this may damage the CCD image

sensor.

8. Apparatus shall not be exposed to

dripping or splashing and no objects

lled with liquids, such as vases, shall be

placed on the apparatus.

9.

The Mains plug is used as a disconnect device

and shall stay readily operable at any time.

4

5

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources

such as radiators, heat registers, or

other apparatus (including ampliers)

that produce heat.

9. Do not defeat the safety purpose of

the polarized or grounding-type plug.

A polarized plug has two blades with

one wider than the other. A grounding

type plug has two blades and a third

grounding prong. The wide blade or the

third prong is provided for your safety.

If the provided plug does not t into

your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being

walked on or pinched particularly at

plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories

specied by the manufacturer.

12. Use only with cart, stand, tripod, bracket,

or table specied by the manufacturer, or

sold with the apparatus.

13. Unplug this apparatus. When a cart is

used, use caution when moving the

cart/apparatus combination to avoid

injury from tip-over.

14. Refer all servicing to qualied service

personnel. Servicing is required when

the apparatus has been damaged in any

way, such as power-supply cord or plug

is damaged, liquid has been spilled or

objects have fallen into the apparatus,

the apparatus has been exposed to rain

or moisture, does not operate normally,

or been dropped.

4

ENG

5

Overview ...........................................................................................

8

About this guide ............................................................................8

Product overview ...........................................................................8

Main features .................................................................................8

Components ...................................................................................8

CHECKING COMPONENTS IN THE PACKAGE .......................8

NAMES OF EACH PART ...........................................................9

Installation .....................................................................................

10

Before installation .......................................................................10

THINGS TO KEEP IN MIND DURING INSTALLATION AND USE

.....10

Initial settings ..............................................................................10

CAMERA ADDRESS SETUP ...................................................10

SETTING COMMUNICATION PROTOCOL ............................. 11

BAUD RATE SETTING ............................................................12

SETTING RS-422A/RS-485 TERMINATION ...........................13

Adapter cable connection ...........................................................15

Cable connection .........................................................................16

Installation precautions ..............................................................19

Separately sold products for installation ..................................19

Installing the camera ...................................................................24

Camera Setup ................................................................................

28

Camera set ...................................................................................32

CAMERA ID .............................................................................32

V-SYNC ....................................................................................32

DAY/NIGHT ..............................................................................33

MOTION DET ...........................................................................36

ZOOM SPEED .........................................................................39

Contents

6

7

DIGITAL ZOOM ........................................................................39

DISPLAY ZOOM .......................................................................40

DISPLAY P/T ............................................................................41

EXIT .........................................................................................41

Video set ......................................................................................42

IRIS ..........................................................................................42

ALC ..........................................................................................42

SHUTTER ................................................................................45

AGC..........................................................................................46

MOTION ...................................................................................47

WHITE BAL ..............................................................................48

FOCUS MODE .........................................................................49

SPECIAL ..................................................................................50

EXIT .........................................................................................52

Preset ...........................................................................................53

Zone set ........................................................................................55

PRIVACY ZONE .......................................................................55

ZONE DIR SET ........................................................................56

ZONE AREA SET .....................................................................57

Auto set ........................................................................................60

AUTO PAN ...............................................................................60

PATTERN .................................................................................62

SCAN .......................................................................................63

AUTO PLAY..............................................................................64

Alarm set ......................................................................................65

ALARM PRIORITY SET ...........................................................66

ALARM IN SET ........................................................................66

ALARM OUT SET ....................................................................66

6

ENG

7

AUTO SET ...............................................................................66

AUX OUT CONTROL ...............................................................66

Other set ......................................................................................67

PROPORTIONAL P/T ..............................................................67

TURBO P/T ..............................................................................67

AUTO CAL ...............................................................................67

D-FLIP ......................................................................................68

CAM RESET ............................................................................68

LANGUAGE .............................................................................68

PASSWORD .............................................................................69

RS-485 .....................................................................................70

Clock set ......................................................................................70

System info ..................................................................................71

Shortcut keys ...............................................................................72

Product Specications ...............................................................

75

8

9

Overview

❚

About this guide

This user guide includes basic instructions for

the product. It is recommended that all users

read this guide before use.

This guide is divided as follows:



“Overview” introduces the user guide and product

related information.



“Installation” explains how to set and install the

product.



“Camera Setup” presents the structure of the

Setup menu for the SCC-C6435(P)/6433(P)

including a detailed explanation of the functions

performed in each submenu.



“Product Speci cations” provides the

specications of the product.

❚

Product overview

This camera is a zoom lens built in smart

dome camera which provides you with the

best monitoring function in connection with

CCTV at banks or companies. This camera is

a high quality surveillance camera using x32

zoom lens and digital zoom IC, it can catch

clear images up to 510 times.

This camera uses an Alarm function for alert

situations and moving camera in the direction

you want, ZOOM-IN and ZOOM-OUT

functions can be remote controlled.

Note

SCC-C6433(P) does not support for WDR function.

❚

Main features



Power: DC 12V/AC 24V



Special functions



WDR to cover the full screen irregardless of its

brightness



DAY/NIGHT to improve the sensitivity by

automatic conversion into the black and white

mode at night or in the environment with low

illumination



White Balance to control the brightness to the

illumination



Backlight Compensation under spotlight or

utmost bright illumination



Auto Focus to automatically adjust the focus

to the subject movement



Privacy zone to hide a specic area for

personal privacy



PAN/TILT for precise control at high speed

❚

Components

CHECKING COMPONENTS IN THE PACKAGE

Please check your camera and accessories

are included in the package. Those

components are as shown below:

SCC-C6435(P)/C6433(P) Camera Holder Adapter

User’s Guide Screws

8

ENG

9

NAMES OF EACH PART

Your camera has the following components:

1. Camera Holder Adapter

2. Camera Body

3. Zoom Lens

4. Cover-dome

5. Alarm Output: N/O, COM, N/C, AO-2, AO-1, GND

6. Alarm Input (1~8): AI-8, AI-7, AI-6, AI-5,GND, AI-4, AI-3, AI-2, AI-1, GND

7. RS-485

: TXD+, TXD-, RXD+, RXD-

8. Power Input: 24V, EARTH, 24V

9. Video Output

10

11

❚

Before installation

THINGS TO KEEP IN MIND DURING INSTALLATION AND USE

• Do not disassemble the camera on your own.

• Always be careful when handling the camera. Do not strike the camera by your sts or shake

it. Please be careful not to be careless when storing and operating it.

• Do not place or operate the camera in any wet environment such as rain or wet surfaces.

•

Do not clean the camera with rough sandpaper. Please always use a dry cloth when cleaning it.

•

Put the camera in a cool area free from direct sunlight. Otherwise, the camera may be damaged.

❚

Initial setting

CAMERA ADDRESS SETUP

Use SW703, SW704, or SW705 for Camera Address setup. You may allocate up to 255

addresses by using SW703 to set the 3rd digit, SW704 the 2nd digit, and SW705 the 1st digit.

EX) In case of Camera Address 1, see the following gure for setup.

Installation

SW703 SW704 SW705

10

ENG

11

SETTING COMMUNICATION PROTOCOL

Use number 1~4 PIN of SW702 to set communication Protocol.

A : SAMSUNG HALF

B : SAMSUNG FULL

Comp

PIN1 PIN2 PIN3 PIN4

A OFF

OFF OFF OFF

B ON

OFF OFF OFF

C OFF

ON OFF OFF

D ON

ON OFF OFF

E OFF

OFF ON OFF

F ON

OFF ON OFF

G OFF

ON ON OFF

H ON

ON ON OFF

I OFF

OFF OFF ON

J ON

OFF OFF ON

K OFF

ON OFF ON

L ON

ON OFF ON

M OFF

OFF ON ON

N ON

OFF ON ON

O OFF

ON ON ON

P ON

ON ON ON

X100 X10 X1

12

13

BAUD RATE SETTING

Use PIN 5 and 6 of SW702.

The factory default setting is set to 9600BPS.

BAUD RATE PIN 5

PIN 6

4800 BPS ON

ON

9600 BPS OFF

ON

19200 BPS ON

OFF

38400 BPS OFF

OFF

12

ENG

13

SETTING RS-422A/RS-485 TERMINATION

As it is shown in the structure map, when Controller and RS-422A/RS-485 is connected,

it should be terminated according to the Cable feature of impedance on the each end of the

transmitting line to transfer the signals in long distance by controlling the reection of the signals

to the lowest.

Termination: using numbers 1 and 2 PIN, turn to ON and it will be terminated.

<RS-485 Half Duplex Organization>

Controller

Division n < 32

Termination

SW1-ON

CAM n

CAM n-1

CAM 2CAM 1

TX+(DATA+)

TX-(DATA-)

RX- RX+RX+ RX- RX+ RX- RX+ RX-

14

15

Note

A communication error may occur if you connect multiple cameras that are assigned the same address

in the network.

Controller

CAM 1

<RS-422A/RS-485 Full Duplex Organization>

CAM 2

CAM n-1

CAM n

Division

n < 32

Division

SW1-ON

SW2-ON

14

ENG

15

❚

Adapter cable connection

SCC-C6435 Adapter Board

16

17

❚

Cable connection

1. First, connect one end of the BNC video cable connector to the Video Output Terminal

(VIDEO OUT).

2. Then, connect the other end of the connector to the Video Input Terminal of the monitor.

Video terminal on the

rear of monitor

BNC Cable

16

ENG

17

3. Connect the Power Adapter to the Power Cable of the camera.

4. Adjust the switch on the Power Adapter to the proper voltage. Then, connect the Power

Adapter's plug to the Power Connector.

7





)

5

3

"

&

7





7

&"

3

5)

7

Power Selection Switch

under the Power Adaptor

Power Selection Switch

under the Power Adaptor

18

19

5. Connect the Remote Control Terminal of the camera and the external Controller.

59%

59%

39%

39%

Adapter Cable

Controller

18

ENG

19

❚

Installation precautions

1. Make sure that the installation site can sufciently support a minimum of four times the net

weight of the SCC-C6435(P)/6433(P) SmartDome camera and other accessories.

2. Install in an area where the space above the ceiling board is over 18 cm (7 in.) high.

3. Use the supplied screws to fasten the camera to the bracket assembly.

4. Keep persons away from the installation area, as there is a risk of falling objects.

Also, move valuables to a safe location before installation.

❚

Separately sold products for installation

Depending on the installation site, it may be convenient to use one of the following products.

1. CEILING MOUNT BRACKET (

SADT-101EC)

This bracket is used for installing the SmartDome camera in the plenum above the drop

ceiling.

20

21

2. WALL MOUNT ADAPTOR (SADT-104WM)

This adaptor is used for installing the SmartDome camera on an indoor wall.

3. HANGING MOUNT ADAPTOR (

SADT-100HM)

This adaptor is used for installing the SmartDome camera to an outdoor wall or a ceiling and

used with CEILING MOUNT ADAPTOR(SADT-100CM).

Page is loading ...

Samsung SCC-C6435P/TRK User manual

Samsung SCC-C6435P/TRK User manual

in other languages

Related papers

Other documents