Art USB Dual Pre User manual

Brand: Art

Model: USB Dual Pre

Category: Musical Equipment

Type: User manual

This manual is also suitable for

The Art USB DUAL PRE PROJECT SERIES is a versatile audio interface that seamlessly blends analog and digital audio worlds, allowing you to connect microphones, instruments, and more to your computer via USB. With its pristine preamps, flexible power options, and comprehensive monitoring capabilities, it's ideal for home recording, podcasting, and live sound applications. Record and monitor with ease, harnessing the power of your computer's DAW to elevate your audio productions.

USB Dual Pre

User’s Manual

IMPORTANT SAFETY INSTRUCTION – READ FIRST

This symbol, whenever it appears, This symbol, wherever it appears, alerts you

alerts you to the presence of uninsulated to important operating and maintenance

dangerous voltage inside the enclosure-voltage instructions in the accompanying literature.

that may be sufficient to constitute a risk of shock. Please read the manual.

Read instructions:

Retain these safety and operating instructions for future reference. Heed all warnings printed here and on the

equipment. Follow the operating instructions printed in this user manual.

Do not open:

There are no user serviceable parts inside. Refer any service work to qualified technical personnel only.

Power sources:

Connect the units power supply to mains power only of the type described in this user manual or marked on

the power supply.

Power supply:

Use the power supply with sealed mains plug appropriate for your local mains supply as provided with the

equipment. If the provided supply does not fit into your outlet consult your service agent. Route the power cord

so that it is not likely to be walked on, stretched or pinched by items placed upon or against it.

Grounding:

Do not defeat the grounding and polarization means of the power supply.

Moisture:

To reduce the risk of fire or electrical shock do not expose the unit to moisture or use in damp or wet

conditions. Do not place container of liquid on unit.

Heat:

Do not locate the unit close to excessive heat or direct sunlight, as this could cause a fire hazard. Locate the

unit away from any equipment, which produces heat such as: power supplies, power amplifiers and heaters.

Environment:

Protect from excessive dirt, dust, heat, and vibration when operating and storing. Avoid tobacco ash, drink

spillage and smoke, especially that associated with smoke machines.

Handling:

Protect the controls from damage during transit. Use adequate padding if you need to ship the unit. To avoid

injury to yourself or damage to the equipment, take care when lifting, moving, or carrying the unit.

Servicing:

Unplug power immediately if equipment is exposed to moisture, the power supply becomes damaged during a

lightning storm or if smoke odor or noise is noted. Refer servicing to qualified technical personnel only.

Installation:

Install the unit in accordance with the instructions printed in the user manual.

INTRODUCTION:

The USB Dual Pre is a full-featured high quality dual portable preamplifier and computer interface

packed into a compact rugged case. It is designed to work over a wide variety of applications from

remote field recording to desktop/studio tracking. Each of the two low noise input channels has up to

48 dB of clean gain with signal present and clip LED indicators. Inputs can be either XLR balanced or

1/4-inch TRS. Each of the 1/4-inch TRS outputs is buffered low impedance balanced.

The USB Dual Pre can be externally powered from the mains via a supplied 12 Volt DC adapter, or

from an internal 9 Volt battery, or from the USB bus itself, or any combination of these power sources.

When running off of the battery alone, you should get in excess of 50 hours of operation when

phantom power is off. Battery life drops to around 20 hours (depending on microphone) when

phantom powering from the battery alone (still enough time to get through a session).

The built-in low noise +48 Volt phantom power supply allows you to power up to 2 microphones as

well as the preamplifier when running from any power sources including the USB bus.

For monitoring, an 1/8-inch TRS mini headphone jack with level and monitor mix controls on the rear

allow for latency free local monitoring of the inputs while recording as well as playback monitoring of

the USB bus. The monitor mix is also routed to the ¼-inch TRS balanced outputs. This lets you use

the 1/4-inch outputs as either a preamplifier out or as the monitor feed to your powered monitors.

The USB interface is fully compliant with the USB 1.1 specification and uses USB adaptive mode for

playback and USB asynchronous mode for record. It will work with the USB audio device drivers built

into Windows 98SE/ME/2000/XP/Vista and Apple OS9.1/OSX computers with native USB support.

No special drivers are needed.

The compact black anodized all aluminum case with rubber sides makes for a rugged design. The

USB Dual Pre will provide years of trouble free service and its high quality audio channels and

versatile powering options make the USB Dual Pre the obvious choice in a wide variety of

applications from Podcasting/Broadcasting to Tracking and Monitoring.

With the USB Dual Pre, your laptop, and a pair of quality condenser microphones you can do some

serious remote recording.

Key Features Include:

• USB Connectivity to Desktop and Laptop Computers

• Low Noise Fully Balanced XLR and 1/4-inch TRS “Combo” Inputs

• Up to 48 dB of Clean Gain

• Built-in Low Noise +48 Volt Phantom Power Supply

• Latency Free Monitoring Mix and Level Controls

• Independent Channel Gain Controls

• 1/4-inch TRS Balanced Monitor and 1/8-inch Headphone Monitor Outputs

• Compact, Stackable all Aluminum Chassis

• Flexible 3-way Power from USB, External Supply, or 9 Volt Battery

CONNECTIONS:

Left and Right “Combo” jacks on the front allow for either XLR or 1/4-inch TRS input connections.

The XLR Input connections are used primarily for balanced microphone input. Pin 2 is positive, pin 3

is negative, and pin 1 is ground. +48 Volt phantom power (when enabled) is supplied to pins 2 and 3

and pin 1 acts the ground return. Do not lift pin 1 when using phantom power. If you are using the

XLR Inputs with a balanced low line level signal or a microphone that does not require phantom

power, make sure that phantom power is turned off. Maximum gain from the balanced XLR Inputs to

the balanced 1/4-inch TRS Monitor Outputs is 48 dB. These inputs can handle microphone signals up

to +6dBu before clipping.

The 1/4-inch Input connections are used for instrument or low line level balanced or unbalanced

signals. The high fixed input impedance works well with guitar and other passive instrument pickups.

You can use an unbalanced or balanced plug with this connection. Maximum gain from the 1/4-inch

input to the balanced 1/4-inch TRS Monitor Output is 48 dB with a balanced source and 42 dB with an

unbalanced source. When the Gain control is at minimum, this input can handle signals up to +6dBu.

The 1/4-inch Monitor Output jacks are active balanced with the Tip positive, Ring negative, and

Sleeve ground. With an output impedance of 600 Ohms and a maximum output level of +10dBu it can

provide clean balanced signals for long cable runs. Normally you would use this output to go directly

into a power amplifier, powered monitors, recording system, or a mixer’s balanced line or insert

inputs. Though we do not recommend it, if you have to go directly into the balanced microphone input

on a mixer make sure that phantom power is off at the mixer. The mixers input pad and level controls

should be set for minimum gain, and the Monitor Level control on the USB Dual Pre should be set at

a low enough level to prevent overdriving the mixers input section.

The 1/8-inch Headphone Monitor Output jack is stereo unbalanced TRS and has an output

impedance of 50 Ohms. It can accommodate a wide variety of headphone models. Maximum output

level is +4dBu.

The power connector on the rear allows for powering from the 12 Volt DC @ 150mA external supply

that is provided with the product. The USB Dual Pre can operate from any external power source that

provides 7.5 Volts to 12 Volts, AC or DC @ 150mA or more. Battery and USB bus powering are also

possible when AC power is not available.

The USB connector is USB 1.1 compliant and should be used to connect directly to one of the USB

connections on your computer. This connection also powers the USB circuitry inside the USB Dual

Pre and will power the whole product if no other power source is available or active. To your

computer this connection looks like a “USB Audio CODEC” and your computer then controls the

sample rate.

Since the USB connection will be carrying high quality digital audio to and from your computer as well

as bus powering the USB interface, we suggest that you use a high quality shielded USB cable for

best performance. Ideally you should connect directly to one of the USB inputs on your computer.

Connecting through a shared hub can reduce power and bandwidth that is available for each USB

device and should be avoided when possible. Though the USB Dual Pre is compatible with USB 1.1

and 2.0, USB 2.0 is preferred for the cabling and computer connection as it allows for more system

bandwidth. If you must use a hub, it should be a powered USB 2.0 compliant hub for best results,

This is especially important if you plan on using multiple units for more channels of simultaneous

digital audio input.

Both analog output jacks and the USB Out can be used at the same time, which is handy when you

want to run to a mixer and instrument amp in a live situation, or when connecting to a computer or

recording system and locally monitoring your source with headphones.

For a typical recording application where you want to add tracks of audio using the USB bus to your

computer, while monitoring the mix externally for low latency, we suggest the following: Connect your

instrument and/or microphone to the USB Dual Pre inputs, then connect to your computer with a

USB cable. Use the 1/4-inch monitor output jacks to feed your powered monitors or analog monitor

system and/or use the 1/8-inch jack for local headphone monitoring. Then use the Monitor Mix control

to locally adjust between the new tracks and the computer playback signal. The new track that you

are recording will be in real time and have no latency in your monitoring system.

CONTROLS and OPERATION:

The Left Gain and Right Gain Controls directly adjust the input amplifiers giving you control over the

dynamic range of your source. You get from 0 to 48dB of gain depending on settings. Set the controls

counterclockwise to minimum gain when connecting the inputs.

The Monitor Mix control allows you to directly blend between the internal preamplifier signals and the

playback signals from your computer. When recording new tracks only or just using the USB Dual

Pre as a microphone or instrument preamplifier set the Mix control to “Preamp”. When using the USB

Dual Pre for USB to audio output monitoring of your computers playback signal, you would set the

Mix control to “Computer”. When set in the middle you get a blend of the direct preamp signal and

signals coming from your computer.

Some recording programs and computer systems provide what is called a “Play-Through” function.

This can be performed through software or hardware. When Play-Through is set to ON, the computer

will output the audio that is being recorded. There is a short delay, or latency with this audio signal.

There is also a potential for the computer’s audio inputs and outputs to be connected together

thereby forming a feedback loop. This can accidentally create very loud and disturbing sounds.

Therefore “Play-Through” is usually set to OFF as the “default” setting in both software and hardware.

If Software/Hardware Play-Through is set to ON and the Monitor Mix is set in the middle, then you will

most likely hear the original preamp signal together with the computer audio signal slightly delayed,

thereby creating an echo effect. This is normal behavior, so while using various Monitor Mix settings it

may be preferable to leave Play-Through set to OFF.

The Monitor Level control adjusts overall monitor level after the mix circuitry and before the monitor

output amplifiers. This control affects the signal levels at both the 1/8-inch headphone and 1/4-inch

balanced monitor output jacks.

The Phantom power switch, on the rear, applies +48 Volt phantom power to the XLR input jacks for

powering microphones, if needed. It is slow at turning on and off and is current limited to protect

sensitive microphones and reduce audible pops. Ideally, when connecting a microphone that requires

phantom power, you should first turn down gain, next connect the microphone, next switch on the

phantom power, and finally bring the gain back up to the desired level. This minimizes pops in your

system and stress on the microphone.

The Power switch, on the rear, is used to turn on power from the battery or external power supply.

Turning this switch off disables these two power sources but if the USB bus is still active then the

USB Dual Pre will be powered by the USB bus alone and the red power LED will still light to indicate

that USB power from your computer is still on. When the switch is in the on position and all three

power sources are available, the USB interface will be powered by the USB bus but the preamp and

phantom power sections will draw their power from the external AC power source or from the battery

if an external source is not available. Normally in a desktop, studio, or home recording setting the

power modes would not be an issue. When used in a portable or remote recording situation the USB

Dual Pre, a laptop computer, a pair of microphones, and a set of headphones, become your entire

system. In this setting you can either power everything from your laptop or if you have a 9 Volt battery

installed and the Power switch is on, power to the preamp and phantom powering sections will come

from the battery and the laptop will only be powering the USB interface. This helps to maximize your

remote recording time.

LED metering circuitry on each channel aids in setting gain and has a fast attack to help indicate any

clipping. The metering is located in the signal chain just after the preamp circuitry to help in setting

signal levels going to your computer. The Monitor controls come after the metering so that you can

use the meters to set the overall input gain on each channel for best recording dynamic range and

then trim the Monitor Mix and Level to the monitor system you are driving. The red “Clip” LED comes

on just before clipping (2dB before digital clipping and 6 dB before analog clipping) and should light

on musical peaks only. The green “Signal” LED comes on around 10dB before the “Clip” LED and

indicates how far below clipping your signal is. The “Signal” LED has a longer release time and

should be on much of the time during performance and if not it indicates that your signal or input gain

may be too low for best results.

A brief note from customer service:

Once in a while a customer will call and say: I think my ART preamp is "noisy". What's wrong?

If you experience unwanted "noise" in your system when you use a stand-alone preamp, please

consider what your signal is and where you're sending it. Some people send the signal from their

preamp to a mic input (they figure, "well, I'm using a mic!") on the board or recorder. This is in fact

incorrect and could create higher overall noise. ART preamps are actually intended to output a nice

fat LINE LEVEL signal. If you send that line level signal to a recorder or mixer's Mic input, that circuit

will usually add more gain to the signal. Gain on top of gain will indeed result in noise. Please treat

the output signal as line level and you'll be pleasantly surprised at your new clean and warm sound.

The same rule applies for guitar and bass players that use ART preamps as their front end. Send the

signal from your preamp to a low gain input on your amp, or even a "loop return" jack which allows

you to bypass the amp's solid state preamp altogether.

USB OPERATION:

Connect your analog jacks and external power supply first. If you are using one of the analog outputs

for local low latency monitoring, connect that to your monitor system or headphones. Next, set the

front panel controls for proper operation as per the previous sections. Then connect the USB cable to

the appropriate input on your computer and lastly to the USB connector on the USB Dual Pre.

Once the USB connection is made and your computer is on, the USB interface circuitry will be

your computer “Default Audio Device” to be “USB Audio CODEC”. Usually the computer will do this

automatically whenever a USB device is first connected, but it is sometimes necessary to make the

selection manually. The same settings may need to be made in your particular audio application as

well (Check your application instructions). These settings should be made while the two units are

connected and powered on. Select one of the following sound recording (input) settings:

WINDOWS 98SE: Settings => Control Panel => Multimedia

Choose the preferred device: “USB Audio Device”

WINDOWS XP: Settings => Control Panel => Sounds and Audio Devices => Audio.

Choose the mixer device: “USB Audio CODEC”

or Programs =>Accessories =>Entertainment =>Volume Control=> Options=> Properties

Choose the mixer device: “USB Audio CODEC”.

WINDOWS VIsta: Settings => Control Panel => Sound => Playback Tab and Record Tab.

Choose: “USB Audio CODEC”

Mac OS9.1+: Control Panels => Sound.

Choose: “USB Audio CODEC”

Mac OS10+: System Preferences => Sound.

Choose: “USB Audio CODEC”

Your computer audio output “Speaker” is now set to be the “USB Audio CODEC” and playback audio

is routed to the USB Dual Pre. This must be done while the USB Dual Pre is connected to the

computer and powered on. After the above settings are made, your computer will automatically

reconfigure itself back to these settings every time the USB Dual Pre is reconnected to the computer.

At this point your recording software will select and control which channels are being recorded and

which channels are being monitored. There are many computer recording software packages

available today that allow for multi-track recording. If you are using multiple units and connecting

more than one over the USB bus, they will appear as “USB Audio CODEC 1”, “USB Audio CODEC

2”, etc. in your recording application. Please refer to your recording software documentation for the

best way to assign channels and set recording and monitoring parameters.

Latency, the time delay between your audio input and the USB output to your computer, is very short

(under 2 milliseconds) in the USB Dual Pre. The latency of your recording software and computer

software drivers can be much more than this. Typically on a Mac the core audio interface has low

latency so this is usually not an issue. USB audio drivers that come with Windows can have enough

latency to cause a discrete delay when monitoring live. If this becomes an issue there are low latency

ASIO drivers available that can greatly reduce your Windows audio latency. Two current resources

for low latency ASIO drivers that will work with the USB Dual Pre are: www.asio4all.com

and

www.usb-audio.com

APPLICATIONS:

Microphone Pre Amplifier:

The USB Dual Pre can be used as a high quality microphone preamplifier suitable for

all dynamic, condenser, and ribbon microphones. Most conventional mixers utilize budget

minded microphone preamps and while very functional, they do not sound all that great. The

USB Dual Pre serves as a quality upgrade that will give you more flexibility and a more robust

tone than standard mixer preamps.

Simply plug a microphone into the XLR input. Apply phantom power if using a

condenser. Then dial up the gain and you are ready to go. Refer to the LEDs on the front for a

visual measure of input gain, and then route the output to a mixer, workstation, or computer via

the 1/4-inch or USB output. The overall analog output level can be adjusted right at the unit.

Since the USB Dual Pre can be battery powered or run totally off the USB bus, it is

ideal as a portable microphone preamp for remote performance or laptop recording.

Phantom Power Supply:

Many mixers, workstations, and computer interface boxes will not supply +48 Volt

phantom power on all microphone inputs. This is a critical feature if you plan to use a

condenser microphone. The USB Dual Pre is a perfect solution to this problem, letting you

connect any microphones to your existing mixer or computer. Operation is identical to what is

covered above. Once again portable laptop recording with high quality condenser microphones

that require real phantom power is possible.

Instrument DI:

The USB Dual Pre will work well as a very functional DI for Bass, Acoustic Guitar and

virtually any other instrument with a 1/4-inch or XLR output. Many people prefer the sound of

ART preamps for responsiveness instead of standard DI’s and preamps. You will also enjoy

more flexibility and control over a standard DI.

Operation is simple, insert the output of the instrument into the input of the USB Dual

Pre. Make sure the volume on the bass or guitar is up most of the way. If you are using any

effects, make sure that the overall output is not greatly increased when the effect is on. Adjust

the input gain knob and refer to the LEDs on the front for a visual measure of input gain. Then

route the output to a mixer, workstation or computer via the 1/4-inch, or USB output. The

overall output can be adjusted at the unit. Both analog outputs and the USB port may be used

at the same time so the 1/4-inch can be routed to an amplifier or monitor system and the USB

to a computer. Using the built-in monitor mixer for monitoring during the record process gives

you the most flexibility.

WARRANTY INFORMATION:

Limited Warranty

Applied Research and Technology will provide warranty and service for this unit in accordance with the

following warrants:

Applied Research and Technology, (A R T) warrants to the original purchaser that this product and the

components thereof will be free from defects in workmanship and materials for a period of one

year from the

date of purchase. Applied Research and Technology will, without charge, repair or replace, at its option,

defective product or component parts upon prepaid delivery to the factory service department or authorized

service center, accompanied by proof of purchase date in the form of a valid sales receipt.

Exclusions

This warranty does not apply in the event of misuse or abuse of the product or as a result of unauthorized

alterations or repairs. This warranty is void if the serial number is altered, defaced, or removed.

A R T reserves the right to make changes in design or make additions to or improvements upon this product

without any obligation to install the same on products previously manufactured.

A R T shall not be liable for any consequential damages, including without limitation damages resulting from

loss of use. Some states do not allow limitations of incidental or consequential damages, so the above

limitation or exclusion may not apply to you. This warranty gives you specific rights and you may have other

rights, which vary from state to state.

For units purchased outside the United States, an authorized distributor of Applied Research and Technology

will provide service.

SERVICE:

The following information is provided in the unlikely event that your unit requires service.

1) Be sure that the unit is the cause of the problem. Check to make sure the unit has power, all cables are

connected correctly, and the cables themselves are in working condition. You may want to consult with your

dealer for assistance in troubleshooting or testing your particular configuration.

2) If you believe the ART unit is at fault, go to www.artproaudio.com

. You may contact Customer Service for

more assistance, or directly request a Return Authorization for service in the “resources” area of the website.

3) If you are returning the unit for service, pack the unit in its original carton or a reasonable substitute. The

original packaging may not be suitable as a shipping carton, so consider putting the packaged unit in another

box for shipping. Print the RA number clearly on the outside of the shipping box.

4) Include, with your unit, a note with the RA number and your contact information including a daytime phone

number, preferably attached to the top of the unit.

SPECIFICATIONS:

Frequency Response: 20 Hz – 20K Hz (+0, -1 dB)

THD: <0.01% @ 1K Hz

CMRR: >60 dB

Channel Separation: >75 dB

Signal to Noise Ratio: >90 dB (Ref 0 dBu)

Equivalent Input Noise: -120 dBu typical (XLR balanced, gain @ maximum)

Input Impedance: >300K Ohms 1/4-inch input, >4K Ohms XLR input

Output Impedance: 600 Ohms (balanced 1/4-inch), 50 Ohms (headphone 1/8-inch)

Maximum Signal Level: +6 dBu in, +10 dBu out (balanced), +4 dBu out (single ended)

Maximum Gain: +48 dB (balanced in-out)

Phantom Power: Switch selectable, +48Volts DC, filtered, current limited

Input Connections: XLR / 1/4-inch TRS “Combo” jack balanced or unbalanced

Output Connection: 1/4-inchTRS balanced, 1/8-inch TRS headphone mini jack

A/D-D/A: 16 Bit, 44.1K Hz or 48K Hz, USB selectable from computer

0.4 ms A/D latency @ 44.1K Hz

Computer Interface: USB 1.1 compliant, Windows 98SE/ME/2000/XP/Vista,

Apple OS9.1/OSX computers with native USB support

Chassis Type: All aluminum black anodized with integral rubber sides

Power Requirements: 7.5-12V DC @ <150mA (external) or USB bus powered or

9V Battery @ 20mA typical, 50mA max. (phantom power)

Dimensions: 1.75inch H x 4.6inch W x 4.7inch D (44.5mm x 117mm x 119mm)

Weight: 1.3 lbs. (0.59 kg)

Note: 0 dBu = 0.775Vrms

ART maintains a policy of constant product improvement.

Therefore, specifications are subject to change without notice.

Go to www.artproaudio.com

for the latest information and support on the USB Dual Pre.

www.artproaudio.com

E-mail: [email protected]

USB Dual Pre 179-5004-101

Art USB Dual Pre User manual

Brand: Art

Model: USB Dual Pre

Category: Musical Equipment

Type: User manual

This manual is also suitable for

Download PDF

report

Art USB Dual Pre User manual

This manual is also suitable for

Art USB Dual Pre User manual

Related papers

Other documents