Revell Concerta M10 Owner's manual

Brand: Revell

Model: Concerta M10

Category: Soundbar speakers

Type: Owner's manual

Revel

M10

Owner’s Manual

HSGP1052-M10_OM 9/12/08 12:18 PM Page 1

Revel

Concerta

™

M10 Owner’s Manual

Table of Contents

3 Introduction

4 Planning Your System

4 Placement

4 Installation

5 Tabletop/Shelf Placement Assembly

8 Wall-Mounting the M10,

Using the Included Wall Bracket

9 Wiring the Speaker

9 Maintenance and Service

10 Specifications

HSGP1052-M10_OM 9/12/08 12:18 PM Page 2

Introduction

Revel

Concerta

™

M10

The Revel

Concerta

™

M10 satellite speaker continues

the longstanding Revel commitment to accurate sound

reproduction. The proprietary transducers utilizing Micro

Ceramic Composite (MCC) diaphragms, precision dividing

networks, sophisticated high-frequency waveguides and

rigid enclosures all combine to deliver uncompromising

performance in any stereo or multichannel home theater

system. In addition, these speakers are magnetically

shielded for safe placement near a CRT television.

Unpacking the Speaker

Carefully unpack the speaker. If you suspect damage

from transit, report it immediately to your dealer and/or

delivery service. Keep the shipping carton and packing

materials for future use. Open the package and verify

the following contents:

(1) Satellite speaker

(1) Table stand

plate

(1) Bottom foot

(1) Small collar

(1) Medium collar

(1) Large collar

(2) Wall-mount end caps

(attached to satellite)

(1) Flat-head Phillips screw

1/4-20 x 1-1/4"

(1) Pan-head Phillips screw

1/4-20 x 3/4"

(6) Flat-head Phillips screws

1/4-20 x 7/8"

(2) Pan-head Phillips screws

1/4-20 x 1"

(3) 1/4-20 Flat washers (3) 1/4-20 Nuts

(1) Allen wrench

Part A

Part B

(1) Wall bracket

with wall

bracket cover

HSGP1052-M10_OM 9/12/08 12:18 PM Page 3

Planning Your System

Before deciding where to best place your speakers,

survey your room and study Figures 1 and 2.

Figure 1: In this overhead view of a typical 5-channel

installation, satellites are used to reproduce sound

for the front and surround channels. A dedicated

loudspeaker reproduces the center channel, and a

subwoofer reproduces low frequencies below the

crossover point.

Figure 2: This overhead view shows a typical home

theater plan. Left/right rear channels are for a

7-channel system. The center rear channel is for

a 6-channel system.

Note: The Revel Concerta M10 is ideally suited

for use with a subwoofer. Contact your Revel

dealer for recommendations on subwoofer

models for your application.

Listening Position

Center Channel

(above or below video screen)

Left

Front

Channel

Right

Front

Channel

Subwoofer

Right

Surround

Channel

Left

Surround

Channel

Placement

Note: The satellite speakers can be placed

directly on a shelf or tabletop, using one of

the three included shelf stands, or mounted

on a wall using the included wall brackets.

Optional floor stands are also available.

Please contact your dealer.

Left and Right Front Channels

For left and right front channels, place one satellite to the

left and another to the right of the television, as shown in

Figure 1. Since the speakers are magnetically shielded,

you can place them close to a CRT TV without worrying

about the magnetic field distorting the picture.

Surround Channels

For left and right surround channels, place one speaker

on the left and another on the right, to the side of or

slightly behind the listening area. The surround speakers

should ideally be mounted at a height of between 4 feet

and 7 feet.

In 6- or 7-channel configurations, place the rear channel(s)

behind the listening position, as shown in Figure 2.

Installation

Please read through this owner’s manual completely

before attempting to install or connect the speakers.

It is understandable that you may be anxious to play your

new system, so every effort has been made to simplify

the installation and connections of the Revel Concerta

M10 loudspeakers.

Before proceeding, you should decide how you would like

to install the M10 loudspeakers. They may be mounted on

the included tabletop/shelf stands, mounted on the wall

using the included wall bracket, or mounted to the

optional floor stands.

Listening Position

Left

Front

Channel

Right

Front

Channel

Subwoofer

Right

Surround

Channel

Left

Surround

Channel

Left

Surround

Channel

Right

Surround

Channel

Center

Surround

Channel

Center Channel

(above or below video screen)

HSGP1052-M10_OM 9/12/08 12:18 PM Page 4

Step One

Choose one of the three shelf stands on which to mount

the satellite. If you decide to place the stand next to a

television, the television’s height should be taken into

consideration. If you choose the shortest stand, follow

steps two to four on page 6. If you choose either of the

taller stands, follow steps two to five on page 7.

Large

27"

30-1/2"

muideMllamS

23-3/8"

7/8"

27"

Tabletop/Shelf

Placement Assembly

HSGP1052-M10_OM 9/12/08 12:18 PM Page 5

Step Three

For Small Table Stand Assembly

Assemble the table stand plate, the small section and

the foot. Place three nuts (provided) in the base of the

foot and secure them in place by inserting three screws

(provided) through the top of the table stand plate.

Step Four

For Small Table Stand Assembly

Run the speaker wire through the base, and screw the

foot assembly to the speaker assembly.

Step Two

For Small Table Stand Assembly

Using the included Allen wrench, remove the bottom end

cap of the speaker by unscrewing the single center

screw on the bottom.

Note: The bottom is the end closest to the

Revel logo on the front grille and the speaker

connections on the rear.

Satellite speaker

Revel logo

End cap

1/4-20 x 3/4"

Screw

1/4-20 x 1-1/4"

Flat-head screw

Speaker wire

(3) 1/4-20 Nuts

Table stand plate

Small section/collar

Foot

(3) 1/4-20 x 7/8"

Flat-head screws

HSGP1052-M10_OM 9/12/08 12:18 PM Page 6

Step Four

For Medium and Large Table Stand Assembly

Use the screw and washer to attach the medium or large

base assembly to the speaker assembly, as shown.

Step Five

For Medium and Large Table Stand Assembly

Run the speaker wire through the table stand plate. Use

three screws (provided) to attach the plate to the bottom

of the base assembly.

Step Two

For Medium and Large Table Stand Assembly

Using the included Allen wrench, remove the bottom end

cap of the loudspeaker by unscrewing the single center

screw on the bottom.

Note: The bottom is the end closest to the

Revel logo on the front grille and the speaker

connections on the rear.

Step Three

For Medium and Large Table Stand Assembly

Run the speaker wire through the collar. Using three

screws, attach the table stand plate to the medium or

large section, as shown.

Satellite speaker

Revel logo

End cap

1/4-20 x 3/4"

Screw

(3) 1/4-20 x 7/8"

Flat-head screws

Speaker wire

1/4-20 x 1"

Pan-head screw

Flat washer

Flat washers

1/4-20 x 1"

Pan-head screw

1/4-20 x 3/4"

an-head screw

(3) 1/4-20 x 7/8"

Flat-head screws

Speaker wire

HSGP1052-M10_OM 9/12/08 12:18 PM Page 7

Wall-Mounting the M10

Using the Included Wall Bracket

The customer is responsible

for the proper selection and

use of mounting hardware,

and for correctly and safely

wall-mounting the speakers.

Step One

Remove the wall-bracket cover

by removing the four wall

bracket screws on the ends,

as shown.

Step Two

Run the speaker wire behind

the wall bracket and out

through the hole at the

bottom. After deciding where

to place the satellite speaker,

attach the wall bracket (in a

vertical position) to the wall,

using the appropriate screws

and anchors.

Step Three

Run the speaker wires out

through the bottom hole of the

wall bracket cover. Resecure

in place, as shown, with four

of the wall bracket screws.

Step Four

Using the included Allen wrench, remove the bottom end

cap of the speaker by unscrewing the single center screw

on bottom.

Note: The bottom is the end closest to the

Revel logo on the front grille and the speaker

connections on the rear.

Step Five

Connect the wires (see page 9).

Replace the end caps while

capturing the wall bracket in

between parts A and B and

securing it in place.

Tighten until snug.

Mounting screws

and anchors

not included

Bottom hole

Wall bracket

End cap

Satellite speaker

Revel logo

End cap

1/4-20 x 3/4"

Screw

Wall-mount

end cap A

Wall-mount

end cap B

HSGP1052-M10_OM 9/12/08 12:18 PM Page 8

Step Six

The wall-bracket design allows for rotation of the speakers

at angles up to 30º of center. Position the speakers so that

they face toward the primary listening position, before

fully tightening.

Wiring the Speaker

After placing the speaker, you are ready to connect it

to your system. First, turn off all audio-system power.

Use high-quality speaker wire to make the connections.

Consult the owner’s manuals included with your amplifier

or receiver, for connection and operation procedures.

Surround Modes

When using the system in a Dolby

Digital or DTS

home

theater system, make sure the receiver or processor is

set to “Small” for all M10 loudspeakers.

Some receivers/processors offer a choice of crossover

frequencies. Select 110Hz as the crossover frequency

for all M10 loudspeakers in the system.

Some Dolby Digital-equipped receivers/processors offer

different setup options for each source or surround

mode, e.g., CD-stereo, DVD, Dolby, Pro Logic

. In each

case, follow your equipment’s instructions to ensure that

the subwoofer output is turned on and that the speakers

are set to “Small” or to a crossover frequency of 110Hz

in each mode.

Wiring and Polarity

The M10 speaker has gold-plated terminals that can

accept bare wire.To ensure proper polarity, connect

each + terminal on the back of the amplifier or receiver

to the respective + (red) terminal on each speaker, as

shown in Figure 3. Connect the – (black) terminals in

a similar way. See the owner’s manuals that were

included with your amplifier or receiver to confirm

connection procedures.

Figure 3: This example shows how to connect bare

wires to the terminals. Banana plugs may also be

inserted directly into the rear of the connector.

1. Loosen the terminals.

2. Inset bare ends; tighten terminals.

Important! DO NOT reverse polarities (+ to – or

– to +) when making connections. Doing so will

degrade the imaging and bass response of the

home theater system.

After correctly placing and wiring the M10 and the rest

of your speaker system, adjust the levels for all of the

channels as recommended by the manufacturer of your

receiver/processor.

Maintenance

and Service

When needed, use a soft cloth to remove any fingerprints

or to wipe off dust. Do not use any cleaning products or

polish. Clean the grille by gentle vacuuming.

If your M10 loudspeaker should ever need service,

please contact your local dealer or distributor, or

visit www.revelspeakers.com for the location of a

service center.

–+

HSGP1052-M10_OM 9/12/08 12:18 PM Page 9

Revel

Concerta

™

M10

Frequency Response (±3dB) 110Hz – 21kHz

Recommended Amplifier Power Range 10 – 150 Watts

Sensitivity (2.83V @ 1m, 2π anechoic) 89dB

Nominal Impedance 8 Ohms

Crossover Frequency 2-1/2-Way high-order at 400Hz and 2.2kHz

Low-Frequency Drivers Dual 3" (76mm) woofers with Micro Ceramic Composite (MCC) cones

LF Extension –3dB @ 110Hz, –6dB @ 100Hz, –10dB @ 80Hz

Mid-Frequency Drivers Dual 3" (76mm) midrange transducers with Micro Ceramic Composite (MCC) cones

High-Frequency Driver 1" (25mm) tweeter with waveguide and Micro Ceramic Composite (MCC) dome

External Dimensions 22-15/16" x 4-1/4" x 4-1/2"

(H x W x D) (582mm x 107mm x 113mm)

Weight (Net) 6.75 lb (3.1kg)

Specifications

4.24

22.94

4.49

Declaration of Conformity

We, Harman Consumer Group, Inc.

2, route de Tours

72500 Ch

teau du Loir

France

declare in own responsibility that the product described

in this owner’s manual is in compliance with technical

standards:

EN 61000-6-3:2001

EN 61000-6-1:2001

Laurent Rault

Harman Consumer Group, Inc.

teau du Loir, France 8/08

22.6

1.8

4.32

23.4

6.25

5.5

4.5

30.5

.91

HSGP1052-M10_OM 9/12/08 12:18 PM Page 10

A valid serial number is required for warranty coverage.

This Revel warranty protects the original retail purchaser for

a period of five (5) years (parts and labor) from any failure

as a result of original manufacturing defects, so long as:

1. The Revel products were purchased within the 50

United States, its territories or Canada.

2. The dealer from whom the Revel products were

purchased was authorized to sell such products at

the time of the original purchase.

3. The original, dated Bill of Sale is presented whenever

service is required during the warranty period.

The balance of this warranty is transferable only if the used

product is purchased from an authorized Revel dealer. This

warranty is only valid for service within the United States,

its territories and Canada; please contact an authorized

Revel dealer for warranty and service information.

Any Revel product not performing satisfactorily may be

returned to the factory for evaluation. Return authorization

must first be obtained by either calling or writing Customer

Service prior to shipping the product. The customer is

responsible for shipping charges to the factory.

Customer Service will pay return shipping charges within

the United States only in the event that the product is

found to be defective, as mentioned above. There are

other stipulations that may apply to shipping charges.

There is no other express warranty on this product. Neither

this warranty nor any other warranty, express or implied,

including implied warranties of merchantability and fitness,

shall extend beyond the warranty period. No responsibility

is assumed for any incidental or consequential damages,

so that the above exclusion or limitation may not apply.

This warranty provides specific legal rights. Other states

may provide additional rights. This warranty is applicable in

the United States, its territories and Canada. Outside of the

United States, its territories and Canada, please contact an

authorized Revel dealer for warranty and service information.

The information this document contains is subject to change

without notice. In the event that there are differences between

this warranty and the provisions of any advertisements,

documentation, product brochures or packaging cartons,

the terms of this warranty will prevail.

For customer service and product shipment information,

go to www.revelspeakers.com.

Limited Warranty

HSGP1052-M10_OM 9/12/08 12:18 PM Page 11

www.revelspeakers.com

250 Crossways Park Drive, Woodbury, NY 11797

8500 Balboa Boulevard, Northridge, CA 91329

516.594.0300

Technical Support: 516.682.3744

Part No. ML-80325-01

Revel, the Revel logo and Concerta are trademarks

of Harman International Industries, Incorporated,

in the United States and/or other countries.

Dolby and Pro Logic are registered trademarks of

Dolby Laboratories.

DTS is a registered trademark of DTS, Inc.

Features, specifications and appearance are subject

to change without notice.

HSGP1052-M10_OM 9/12/08 12:18 PM Page 12

Revell Concerta M10 Owner's manual

Brand: Revell

Model: Concerta M10

Category: Soundbar speakers

Type: Owner's manual

Download PDF

report

Revell Concerta M10 Owner's manual

Revell Concerta M10 Owner's manual

Related papers

Other documents