Assembly Instruction
Customer Service
Tel/Fax: 281.500.9372
Toll Free: 773.299.8111 (Mon - Fri 9am - 5pm)
Email: [email protected]
WARNING:
>This unit has been designed to support the
maximum loads shown. Exceeding these
load limits could cause sagging, instability,
product collapse, and/or serious injury.
>DO NOT allow children to climb on unit.
>Put heavier items on lower shelves.
its Space. its Budget
www.furinno.com
Fix the side unit to table using Screw(1).
Tighten Cam-Lock Nut(12)uisng screwdriver.
STEP 10
Install Insert Cap(8)to Panel(D)using hammer.
Fix Cam-Lock Screw(11)into pre-drilled holes.
STEP 7
Tighten Leg(10)to Panel(E)using Top Cap(9).
STEP 8
Tighten Pole(6),(7)and Leg(10)to Panel(D)(E)(F).
STEP 9
Recommended Maximum Weight
Furinno Compact Computer Desk
1118120140430
MODEL : 11181
39”(W) x 33.6”(H) x 15.6”(D)DIMENSION :
20
*Unit in Pound(lbs)
10
10
10
Tools RequiredNo Tools Required
Recomm. 1 Person
(11)x4pcs
(8)x1pcs
unfinished surface
unfinished surface
(6)x1pcs
(10)x1pcs
(7)x1pcs
(9)x2pcs
(10)x2pcs
(1)x6pcs
Recomm. 2 Person
Approx. 5 minutesApprox. 10 minutesApprox. 15 minutesApprox. 30 minutes
STEP 5
5.1 Attach assembled unit to Panel(A).
5.2 Tighten Cam-Lock Nut(12)using screwdriver.
5.3 Fix L-Bracket(4)using Screw(2).
Install Nail Leg(5)to the bottom of Panel(B,C)
using hammer.
STEP 6
STEP 3
Attach Panel(G)(H)to Panel(B)(C)using Screw(1). Screw Cam-Lock Screw(11)into pre-drilled holes
on Panel(A).
STEP 4
STEP 1
Insert Dowel(3)and Cam-Lock Nut(12)to Panel(B,C,I).
Note: Arrow on Cam-Lock Nut(12)should be
pointing towards hole.**
STEP 2
Install L-Bracket(4)on Panel(H)using Screw(2).
(12)x2pcs
(3)x1pcs
(12)x2pcs
(11)x4pcs
(2)x1pcs
(4)x1pcs
(3)x2pcs
(2)x1pcs
(1)x8pcs
USEFUL HINTS BEFORE YOU START:
1. Read each step carefully before starting.
2. It is important that each step is performed in correct order to avoid difficulties.
3. Identify, sort and count the parts before assembly.
4. Assemble your furniture on packaging cardboard to prevent scratch or damage.
5. Clean the product with mild cleanser using soft damped cloth. Do not use harsh or abrasive cleanser.
6. Using uncompatible hardware might cause damage to product.
1
2
3
14pcs
4pcs
4pcs
A 1pcs
Top Panel
Plastic Dowel
No Hardware List Qty No QtyParts List
Long Screw
Short Screw
4
5
6
2pcs
4pcs
1pcs
Long Pole
L-Bracket
Nail Leg
7
8
9
1pcs
1pcs
2pcs
Top Cap
Short Pole
Insert Cap
10
11
12
3pcs
6pcs
6pcs
Cam-Lock Nut
Leg
Cam-Lock Screw
B
C
1pcs
1pcs
Right Side Panel
Left Side Panel
D
E
F
1pcs
1pcs
1pcs
Shelf Panel
Upper Top Panel
Bottom Panel
G
H
1pcs
2pcs
Skirt Panel
I 1pcs
Apron Panel
Bottom Cross Bar
/
