Zanussi ZWI1105 User manual

Category
Washing machines
Type
User manual
EN
User manual 2
EL
Οδηγίες Χρήσης 24
ES
Manual de instrucciones 52
Washing Machine
Πλυντήριο ρούχων
Lavadora
ZWI 1105
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2
Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4
Washing Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7
Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9
First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13
What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 15
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 18
Consumption values _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 18
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 18
Building in _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 20
Environmental concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ 22
Subject to change without notice.
Safety information
Important! Read carefully & keep for future reference.
The safety of Your appliance complies with the industry
standards and with legal requirements on the safety of
appliances. However, as manufacturers, we feel it is
our duty to provide the following safety notes.
It is most important that this instruction book should
be retained with the appliance for future reference.
Should the appliance be sold or transferred to another
owner, or should you move house and leave the appli-
ance, always ensure that the book is supplied with the
appliance in order that the new owner can get to know
the functioning of the appliance and the relevant warn-
ings.
You MUST read them carefully before installing or us-
ing the appliance.
Before first starting up, check the appliance for any
damage incurred during transport. Never connect up a
damaged appliance . If parts are damaged, contact your
supplier.
If the appliance is delivered in the winter months when
there are minus temperatures. Store it at room temper-
ature for 24 hours before using for the first time.
General safety
It is dangerous to alter the specifications or attempt to
modify this product in any way.
During high temperature wash programmes the door
glass may get hot. Do not touch it!
Make sure that small pets and children do not climb
into the drum. To avoid this, please check into the
drum before using.
Any objects such as coins, safety pins, nails, screws,
stones or any other hard, sharp material can cause ex-
tensive damage and must not be placed into the ma-
chine.
Only use the advised quantities of fabric softener and
detergent. Damage to the fabric can ensue if you over-
fill. Refer to the manufacturer’s recommendations of
quantities.
Wash small items such as socks, laces, washable belts
etc in a washing bag or pillow case as it is possible for
such items to slip down between the tub and the inner
drum.
Do not use your washing machine to wash articles with
whalebones, material without hems or torn material.
Always unplug the appliance and turn off the water
supply after use, cleaning and maintenance.
Under no circumstances should you attempt to repair
the machine yourself. Repairs carried out by inexper-
ienced people may cause injury or serious malfunc-
tioning. Contact your local Service Centre. Always in-
sist on genuine spare parts.
Installation
This appliance is heavy. Care should be taken when
moving it.
When unpacking the appliance, check that it is not
damaged. If in doubt, do not use it and contact the
Service Centre.
All packing and transit bolts must be removed before
use. Serious damage can occur to the product and to
property if this is not adhered to. See relevant section
in the user manual.
After having installed the appliance, check that it is not
standing on the inlet and drain hose and the worktop is
not pressing the electrical supply cable against the
wall.
2
www.zanussi.com
If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely
under the appliance.
Always be sure, that there is no water leakage from ho-
ses and their connections after the installation.
If the appliance is installed in a location subject to
frost, please read the “dangers of freezing” chapter.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or compe-
tent person.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or com-
petent person.
Use
This appliance is designed for domestic use. It must
not be used for purposes other than those for which it
was designed.
Only wash fabrics which are designed to be machine
washed. Follow the instructions on each garment label.
Do not overload the appliance. See the Washing Pro-
gramme Table.
Before washing, ensure that all pockets are empty and
buttons and zips are fastened. Avoid washing frayed or
torn articles and treat stains such as paint, ink, rust,
and grass before washing. Underwired bras must NOT
be machine washed.
Garments which have been in contact with volatile pe-
troleum products should not be machine washed. If
volatile cleaning fluids are used, care should be taken
to ensure that the fluid is removed from the garment
before placing in the machine.
Never pull the power supply cable to remove the plug
from the socket; always take hold of the plug itself.
Never use the appliance if the power supply cable, the
control panel, the working surface or the base are dam-
aged so that the inside of the washing machine is ac-
cessible.
Child safety
This appliance is not intended for use by person (in-
cluding children) with reduced physical sensory or
mental capabilities or lack of experience and knowl-
edge unless they have been given supervision or in-
struction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
The packaging components (e.g. plastic film, polystyr-
ene) can be dangerous to children - danger of suffoca-
tion! Keep them out of children’s reach
Keep all detergents in a safe place out of children’s
reach.
Make sure that children or pets do not climb into the
drum. To prevent children and pets becoming trapped
inside the drum this machine incorporates a special
feature.
To activate this device, ro-
tate the button (without
pressing it) inside the
door clockwise until the
groove is horizontal. If
necessary use a coin.
To disable this device and
restore the possibility of
closing the door, rotate the
button anti-clockwise until
the groove is vertical.
3
www.zanussi.com
Product description
1
Detergent dispenser drawer
2
Control panel
3
Door opening handle
4
Rating plate
5
Drain pump
6
Adjustable feet
1 2
3
4
5
6
Detergent dispenser drawer
Compartment for detergent used for prewash and soak
phase or for stain remover used during the stain action
phase (if available). The prewash and soak detergent is
added at the beginning of the wash programme. The stain
remover is added during the stain action phase.
Compartment for powder or liquid detergent used for
main wash. If using liquid detergent pour it just before
starting the programme.
Compartment for liquid additives (fabric softener,
starch).
Follow the product manufacturer’s recommendations on
quantities to use and do not exceed the «MAX» mark in the
detergent dispenser drawer. Any fabric softener or starch-
ing additives must be poured into the compartment before
starting the wash programme.
Control panel
Below is a picture of the control panel. It shows the programme selector dial as well as the buttons and pilot lights.
These are presented by relevant numbers on the following pages.
4
www.zanussi.com
1 2 3 4 5 6
B
C
A
7
1
Programme selector dial
2
SPIN reduction button
3
OPTIONS button
4
EXTRA RINSE button
5
START/PAUSE button
6
DELAY START button
7
Indicator pilot lights
Table of symbols
Programme selector dial
Cottons Wool (Handwash)
Economy programme Delicates
Cold wash Rinses
Synthetics Drain
Easy Iron Spin
Buttons Lights
Spin Rinse Hold
Options Prewash
Extra Rinse Super Quick
Start/Pause
Delay start
Phase lights
/
Prewashing or Washing
+
Rinsing or spinning
End
5
www.zanussi.com
Programme selector dial, spin speed button and available options
Programme Selector Dial
It allows you to switch the appliance on/off and/or to se-
lect a programme.
Available options:
Spin
By pressing this button you can change the spin speed of
the selected programme or to select Rinse Hold option.
Rinse hold
By selecting this function the water of the last rinse is not
emptied out to prevent the fabrics from creasing. Before
opening the door it will be necessary to empty out the wa-
ter. To empty out the water, please read the paragraph «At
the end of the programme».
Prewash
By selecting this option the machine performs a prewash
cycle before the main wash phase. The washing time will
be prolonged. This option is recommended for heavily
soiled laundry.
Super Quick
Short cycle for lightly soiled items or for laundry which
needs only freshening up. We recommend you to reduce
the fabrics loading.
Extra Rinse
This appliance is designed to save energy. If it necessary
to rinse the laundry using an extra quantity of water (extra
rinse), select this option. Some additional rinses will be
performed. This option is recommended for people who
are allergic to detergents, and in areas where the water is
very soft.
Start Pause
This button allows you to start or to interrupt the selected
programme.
Delay Start
The start of the programme can be delayed by 3, 6 or 9
hours by means of this button.
Indicator pilot light (7)
B
C
A
When selecting a washing programme both lights A and
B illuminate.
After having pressed the button 5 the only light corre-
sponding to the running phase stays on. The machine
starts working and the door is locked.
The light C illuminates at the end of the washing cycle.
After a few minutes the door can be opened.
If the draining programme is selected any light
will illuminate.
6
www.zanussi.com
Washing Programmes
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Options
Detergent
Compartment
COTTONS
90° - 60°
Main wash - Rinses
Maximum spin speed at 1000 rpm
Max. load 6 kg - Reduced load 3 kg
1)
White cotton (heavily or normally soiled items).
SPIN REDUCTION
RINSE HOLD
PREWASH
2)
SUPER QUICK
EXTRA RINSE
COTTON + ECO
60°
Main wash - Rinses
Maximum spin speed at 1000 rpm
Max. load 6 kg
STANDARD PROGRAMME for the Energy Label consumption values.
White or fast colour cotton (normally or slightly soiled items).
This programme can be selected for slightly or normally soiled cotton
items. The temperature will decrease and the washing time will be ex-
tended. This allows to obtain a good washing efficiency by saving en-
ergy.
SPIN REDUCTION
RINSE HOLD
PREWASH
2)
EXTRA RINSE
COTTONS
60° - 40° - 30° - Cold
Main wash - Rinses
Maximum spin speed at 1000 rpm
Max. load 6 kg - Reduced load 3 kg
1)
White and coloured cotton (normally soiled items).
SPIN REDUCTION
RINSE HOLD
PREWASH
2)
SUPER QUICK
EXTRA RINSE
COTTON + ECO
40°
Main wash - Rinses
Maximum spin speed at 1000 rpm
Max. load 6 kg
STANDARD PROGRAMME for the Energy Label consumption values.
White or non fast colour cotton (normally or slightly soiled items).
This programme can be selected for slightly or normally soiled cotton
items. The temperature will decrease and the washing time will be ex-
tended. This allows to obtain a good washing efficiency by saving en-
ergy.
SPIN REDUCTION
RINSE HOLD
PREWASH
2)
EXTRA RINSE
7
www.zanussi.com
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Options
Detergent
Compartment
SYNTHETICS
60° - 40° - 30° - Cold
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 3 kg - Reduced load 1.5 kg
1)
Synthetic or mixed fabrics: underwear, coloured garments, non-shrink
shirts, blouses.
SPIN REDUCTION
RINSE HOLD
PREWASH
2)
SUPER QUICK
EXTRA RINSE
EASY IRON
40°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 1 kg
Synthetic or mixed fabrics
Selecting this programme the laundry is gently washed and spun to
avoid any creasing. In this way ironing is easier. Furthermore the ma-
chine will perform additional rinses.
SPIN REDUCTION
RINSE HOLD
PREWASH
2)
EXTRA RINSE
DELICATES
40° - 30° - Cold
Main wash - Rinses
Maximum spin speed 700 rpm
Max. load kg 3 - Reduced load kg 1.5
1)
Delicate fabrics: acrylics, viscose, polyester.
SPIN REDUCTION
RINSE HOLD
PREWASH
2)
SUPER QUICK
EXTRA RINSE
WOOL/HANDWASH
30° - Cold
Main wash - Rinses
Maximum spin speed at 1000 rpm
Max. load 2 kg
Washing programme for machine washable wool as well as for hand
washable woollens and delicate fabrics. Note: A single or bulky item
may cause imbalance. If the appliance doesn’t perform the final spin
phase, add more items, redistribute the load manually and then select
the spinning programme.
SPIN REDUCTION
RINSE HOLD
RINSE
Rinse
Maximum spin speed at 1000 rpm
Max. load 6 kg
With this programme it is possible to rinse and spin cotton garments
which have been washed by hand. The spin speed can be reduced.
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
8
www.zanussi.com
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Options
Detergent
Compartment
DRAIN
Draining of water
Max. load 6 kg
For emptying out the water of the last rinse in programmes with the
Rinse Hold option set.
SPIN
Drain and long spin
Maximum spin speed at 1000 rpm
Max. load 6 kg
Separate spin for hand washed cotton garments and after programmes
with the Rinse Hold option selected. You can choose the spin speed
by pressing the relevant button to adapt it to the fabrics to be spun.
SPIN REDUCTION
O = OFF
For cancelling the programme which is running or to switch the machine off .
1) If you select the Super Quick option by pressing button 3, we recommend that you reduce the maximum load as indicated. Full
loading is possible however with somewhat reduced cleaning results.
2) If using liquid detergents, a programme without PREWASH must be selected.
Helpful hints and tips
Sorting out the laundry
Follow the wash code symbols on each garment label and
the manufacturer’s washing instructions. Sort the laundry
as follows: whites, coloureds, synthetics, delicates, wool-
lens.
Before loading the laundry
Never wash whites and coloureds together. Whites may
lose their whiteness in the wash.
New coloured items may run in the first wash; they should
therefore be washed separately the first time.
Button up pillowcases, close zip fasteners, hooks and
poppers. Tie any belts or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special detergent or
detergent paste.
Treat curtains with special care. Remove hooks or tie them
up in a bag or net.
Removing stains
Stubborn stains may not be removed by just water and de-
tergent. It is therefore advisable to treat them prior to
washing.
Blood: treat fresh stains with cold water. For dried stains,
soak overnight in water with a special detergent then rub
in the soap and water.
Oil based paint: moisten with benzine stain remover, lay
the garment on a soft cloth and dab the stain; treat several
times.
Dried grease stains: moisten with turpentine, lay the gar-
ment on a soft surface and dab the stain with the fingertips
and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust removing
product used cold. Be careful with rust stains which are
not recent since the cellulose structure will already have
been damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well (whites and fast
coloureds only).
9
www.zanussi.com
Grass: soap lightly and treat with bleach (whites and fast
coloureds only).
Ball point pen and glue: moisten with acetone
1)
, lay the
garment on a soft cloth and dab the stain.
Lipstick: moisten with acetone as above, then treat stains
with methylated spirits. Treat any residual marks with
bleach.
Red wine: soak in water and detergent, rinse and treat with
acetic or citric acid, then rinse. Treat any residual marks
with bleach.
Ink: depending on the type of ink, moisten the fabric first
with acetone
1)
, then with acetic acid; treat any residual
marks on white fabrics with bleach and then rinse thor-
oughly.
Tar stains: first treat with stain remover, methylated spirits
or benzine, then rub with detergent paste.
Detergents and additives
Good washing results also depend on the choice of deter-
gent and use of the correct quantities to avoid waste and
protect the environment.
Although biodegradable, detergents contain substances
which, in large quantities, can upset the delicate balance
of nature.
The choice of detergent will depend on the type of fabric
(delicates, woollens, cottons, etc.), the colour, washing
temperature and degree of soiling.
All commonly available washing machine detergents may
be used in this appliance:
powder detergents for all types of fabric
powder detergents for delicate fabrics (60°C max) and
woollens
liquid detergents, preferably for low temperature wash
programmes (60°C max) for all types of fabric, or spe-
cial for woollens only.
The detergent and any additives must be placed in the ap-
propriate compartments of the dispenser drawer before
starting the wash programme.
If using liquid detergents, a programme without prewash
must be selected.
Your appliance incorporates a recirculation system which
allows an optimal use of the concentrated detergent.
Follow the product manufacturer’s recommendations on
quantities to use and do not exceed the «MAX» mark in
the detergent dispenser drawer.
Quantity of detergent to be used
The type and quantity of detergent will depend on the type
of fabric, load size, degree of soiling and hardness of the
water used.
Follow the product manufacturers’ instructions on quanti-
ties to use.
Use less detergent if:
you are washing a small load
the laundry is lightly soiled
large amounts of foam form during washing.
Degrees of water hardness
Water hardness is classified in so-called “degrees” of
hardness. Information on hardness of the water in your
area can be obtained from the relevant water supply com-
pany, or from your local authority. If the water hardness
degree is medium or high we suggest you to add a water
softener following always the manufacturer’s instructions.
When the degree of hardness is soft, readjust the quantity
of the detergent.
First use
Ensure that the electrical and water connections
comply with the installation instructions.
Remove the polystyrene block and any material
from the drum.
Pour 2 litres of water into the main wash com-
partment
of the detergent drawer in order to
activate the ECO valve. Then run a cotton cycle at
the highest temperature without any laundry in
the machine, to remove any manufacturing resi-
due from the drum and tub. Pour 1/2 a measure
of detergent into the main wash compartment and
start the machine.
1) do not use acetone on artificial silk
10
www.zanussi.com
Daily use
Load the laundry
Open the door by carefully
pulling the door handle
outwards. Place the laun-
dry in the drum, one item
at a time, shaking them
out as much as possible.
Close the door.
Make sure that no laundry
stays between the seal and
the door. There is a risk of
water leakage or damage
to the laundry.
Measure out the detergent and the fabric softener
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent required, pour it into the
main wash compartment
or in the appropriate com-
partment if the selected programme/option it requires
(see more details in "Detergent dispenser drawer").
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
«MAX» mark in the drawer). Close the drawer gently.
Select the required programme by turning the
programme selector dial (1)
Turn the programme selector dial to the required pro-
gramme. The washing machine will automatically select
the maximum spin value provided for the programme you
have chosen. You can change this value by pressing the
corresponding button. The green pilot light of the button 5
starts to flash.
The selector dial can be turned either clockwise or coun-
terclockwise. Turn to position
to reset programme/
Switching the machine off.
At the end of the programme the selector dial must be
turned to position
, to switch the machine off.
Caution! If you turn the programme selector dial to
another programme when the machine is working,
the red pilot light of button 5 will blink 3 times to indicate
a wrong selection. The machine will not perform the new
selected programme.
Select the spin speed or Rinse Hold option by
pressing button 2
The relevant light will light up.
When selecting a programme, the light corresponding to
the maximum speed allowed for that programme will illu-
minate.
Select the available options by pressing buttons 3
and 4
Depending on the programme, different functions can be
combined. These must be selected after choosing the de-
sired programme and before starting the programme.
When these buttons are pressed, the corresponding pilot
lights illuminate. When they are pressed again, the pilot
lights go out. If an incorrect option is selected, the inte-
grated red pilot light of the button 5 flashes for 3 times.
For the compatibility among the washing pro-
grammes and the options see chapter «Washing
Programmes».
Select the Delay Start by pressing button 6
Before you start the programme, if you wish to delay the
start, press the button 6 repeatedly, to select the desired
delay. The relevant light illuminates.
You must select this option after you have set the pro-
gramme and before you start the programme.
You can cancel or modify the delay time at any moment,
before you press button 5.
Selecting the delayed start:
1. Select the programme and the required options.
2. Select the delay start by pressing the button 6.
3. Press button 5:
11
www.zanussi.com
the machine starts its hourly countdown.
The programme will start after the selected delay
has expired.
Cancelling the delayed start after having started the pro-
gramme:
1. Set the washing machine to PAUSE by pressing but-
ton 5.
2. Press button 6 once, the light relevant to the selected
delay goes off
3. Press button 5 again to start the programme.
The Delay Start can not be selected with DRAIN pro-
gramme.
Important! The selected delay can be changed only after
selecting the washing programme again.
The door will be locked throughout the delay time. If you
need to open the door, you must set the machine to
PAUSE (by pressing the button 5) and then wait a few
minutes. After you have closed the door, press the button
5 again.
Start the programme by pressing button 5
To start the selected programme, press the button 5, the
corresponding green pilot light stops blinking. The pilot
light corresponding to the running phase illuminates. The
appliance starts operating and the door is locked.
To interrupt a programme which is running, press the but-
ton 5: the corresponding green pilot light starts blinking.
To restart the programme from the point at which it was
interrupted, press the button 5 again. If you have chosen a
delayed start, the machine will begin the countdown.
If an incorrect option is selected, the red pilot light of the
button 5 blinks 3 times.
Interrupting a programme
Press the button 5 to interrupt a programme which is run-
ning, the corresponding green pilot light starts blinking.
Press the button again to restart the programme.
Cancelling a programme
Turn the selector dial to to cancel a programme which
is running. Now you can select a new programme.
Opening the door
After the programme has started the door is locked. If, for
any reason, you need to open it, set firstly the machine to
PAUSE by pressing the button 5. After a few minutes it
will be possible to open the door.
If the door remains locked, this means that the machine is
already heating or that the water level is too high. In any
case, do not try to force the door!
If you cannot open the door but you need to open it you
have to switch the machine off by turning the selector dial
to
. After a few minutes the door can be opened (pay
attention to the water level and temperature!).
After closing the door, it is necessary to select the pro-
gramme and options again and to press button 5.
At the end of the programme
The machine stops automatically. The light of button 5
and the light corresponding to the just finished washing
phase go off.
The light C illuminates. After a few minutes the door can
be opened.
If you have set a programme or an option that ends with
water left in the tub, the light C illuminates. The door re-
mains locked to indicate that the water must be emptied
out before opening the door. During this time, the drum
continues to run at regular intervals until the water drain-
ing.
Follow the below instructions to empty out the water:
1.
Turn the programme selector dial to
.
2. Set the draining or spinning programme.
3. If needed, reduce the spin speed, .
4. Press button 5.
At the end of the programme, the door can be now
opened. Turn the programme selector dial to
to switch
the machine off.
Remove the laundry from the drum and carefully check
that the drum is empty. If you do not intend to carry out
another wash, close the water tap. Leave the door open to
prevent the formation of mildew and unpleasant smells.
Stand by: once the programme has finished after a
few minutes the energy saving system is enabled
with the pilot lights switched on. By pressing any button
the appliance will come out of the energy saving status.
12
www.zanussi.com
Care and cleaning
Warning! You must DISCONNECT the appliance
from the electricity supply, before you can carry out
any cleaning or maintenance work.
Descaling
The water we use normally contains lime. It is a good idea
to periodically use a water softening powder in the ma-
chine. Do this separately from any laundry washing, and
according to the softening powder manufacturer's instruc-
tions. This will help to prevent the formation of lime de-
posits.
External cleaning
Clean the exterior cabinet of the appliance with soap and
water only, and then dry thoroughly.
Cleaning the dispenser drawer
The washing powder and additive dispenser drawer
should be cleaned regularly.
Remove the drawer by
pressing the catch down-
wards and by pulling it
out. Flush it out under a
tap, to remove any traces
of accumulated powder.
To aid cleaning, the top
part of the additive com-
partment should be re-
moved.
Cleaning the drawer recess
Having removed the draw-
er, use a small brush to
clean the recess, ensuring
that all washing powder
residue is removed from
the upper and lower part of
the recess.
Replace the drawer and run the rinse programme with-
out any clothes in the drum.
Cleaning the pump
The pump should be inspected regularly and particularly
if:
the appliance does not empty and/or spin;
the appliance makes an unusual noise during draining
due to objects such as safety pins, coins etc. blocking
the pump;
a problem with water draining is detected (see chapter
“What to do if...” for more details).
Warning! Before opening the pump door, switch the
appliance off and remove the mains plug from the
socket.
Proceed as follows:
Unplug the appliance.
If it is necessary, wait until the water has cooled down.
Place a container close to
the pump (A) to collect
any spillage.
Pull out the emergency
emptying hose (B), place it
in the container and re-
move its cap.
When no more water comes out, unscrew the pump
cover by turning it anti-clockwise and remove the filter.
Use pliers, if necessary. Always keep a rag nearby to
dry up any water spillage when removing the cover.
Clean the filter under a tap, to remove any traces of fluff.
13
www.zanussi.com
Remove foreign bodies
and fluff from the filter seat
and from the pump impel-
ler.
Check carefully whether
the pump impeller rotates
(it rotates jerkily). If it
doesn’t rotate, please con-
tact your Service Centre.
Put the cap back on the
emergency emptying hose
and place the latter back in
its seat.
Replace the filter into the
pump by inserting it cor-
rectly into the special
guides. Screw the pump
cover firmly by turning it
clockwise.
Caution! When the appliance is in use and
depending on the programme selected there can be
hot water in the pump.
Never remove the pump cover during a wash cycle, always
wait until the appliance has finished the cycle, and is
empty. When refitting the pump cover, ensure it is
securely re-tightened so as to stop leaks and young
children being able to remove it.
Cleaning the water inlet filters
Important! If the appliance doesn't fill, takes long to fill
with water, the starting button blinks yellow or the display
(if available) shows the relevant alarm (see chapter "What
to do if..." for more details), check if the water inlet filters
are blocked .
To clean the water inlet filters:
Turn off the water tap.
Unscrew the hose from
the tap.
Clean the filter in the
hose with a stiff brush.
Screw the hose back onto the tap. Make sure the
connection is tight.
Unscrew the hose from the machine. Keep a rag
nearby because some water may flow.
Clean the filter in the valve with a stiff brush or with
the piece of cloth.
35°
45°
Screw the hose back to the machine and make sure
the connection is tight.
Turn on the water tap.
Frost precaution
If the machine is exposed to temperatures below 0°C, cer-
tain precautions should be taken.
Turn off the water tap.
Unscrew the inlet hose.
Place the end of the emergency emptying hose and that
of the inlet hose in a bowl placed on the floor and let
water drain out.
Screw the water inlet hose back on and reposition the
emergency emptying hose after having put the cap on
again.
When you intend to start the machine up again, make
sure that the room temperature is above 0°C.
Emergency emptying out
If the water is not discharged, proceed as follows to empty
out the machine:
pull out the plug from the power socket;
close the water tap;
14
www.zanussi.com
if necessary, wait until the water has cooled down;
open the pump door;
place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove its
cap. The water should drain by gravity into the bowl.
When the bowl is full, put the cap back on the hose.
Empty the bowl. Repeat the procedure until water stops
flowing out;
clean the pump if necessary as previously described;
replace the emergency emptying hose in its seat after
having plugged it;
screw the pump cover again and close the door.
Important! Every time you drain the water through the
emergency emptying hose you must pour 2 litres of water
into the main wash compartment of the detergent drawer
and then run the drain programme. This will activate the
ECO Valve device avoiding that part of the detergent
remains unused at next washing.
What to do if…
Certain problems are due to lack of simple maintenance or
oversights, which can be solved easily without calling out
an engineer. Before contacting your local Service Centre,
please carry out the checks listed below.
During machine operation it is possible that the red pilot
light of button 5 blinks to indicate that the machine is not
working.
It is possible to recognize the fault machine by the number
of button 5 light flashes. If the number of flashes is differ-
ent from the ones indicated below, this is related to a fault
that you can not solve. In this case, contact your local
Service Centre.
Press simultaneously the buttons 4 and 5 for a few sec-
onds. The red button 5 light will flash for a short time as
described (the green flash is not to be considered) :
4 flashes = «The washing machine does not start», fol-
low the corresponding suggestions in «Possible
cause/Solutions» box and restart the programme.
1 flash = «The machine does not fill», follow the corre-
sponding suggestions in «Possible cause/Solutions»
box and restart the programme.
2 flashes = «The machine does not empty and/or does
not spin», follow the corresponding suggestions in
«Possible cause/Solutions» box and restart the pro-
gramme.
Once the problem has been eliminated, press the button 5
to restart the programme. If after all checks, the problem
persists, contact your local Service Centre.
Problem Possible cause/Solution
The washing machine does not start:
The door has not been closed (the button 5 red light blinks).
Close the door firmly.
The plug is not properly inserted in the power socket.
Insert the plug into the power socket.
There is no power at the socket.
Please check your domestic electrical installation.
The main fuse has blown.
Replace the fuse.
The programme selector dial is not correctly positioned and the button 5 has
not been pressed.
Please turn the selector dial and press the button 5 again.
The delay start has been selected.
If the laundry are to be washed immediately, cancel the delay start.
15
www.zanussi.com
Problem Possible cause/Solution
The machine does not fill:
The water tap is closed (the button 5 red light blinks).
Open the water tap.
The inlet hose is squashed or kinked (the button 5 red light blinks).
Check the inlet hose connection.
The filter in the inlet hose or the inlet valve filter are blocked (the button 5 red
light blinks).
Clean the water inlet filters. (See "Cleaning the water inlet filters" for more
details).
The door is not properly closed (the button 5 red light blinks).
Close the door firmly.
The machine does not empty and/or
does not spin:
The drain hose is squashed or kinked (the button 5 red light blinks).
Check the drain hose connection.
The drain filter is clogged (the button 5 red light blinks).
Clean the drain filter.
An option or a programme that ends with the water still in the tub or a that
eliminates all the spinning phases has been selected.
Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
Redistribute the laundry.
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much foam) has been
used.
Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is not
always easy to see this as the water runs down the hose; check to see if it is
damp.
Check the water inlet hose connection.
The drain or inlet hose is damaged.
Replace it with a new one.
The cap on the emergency emptying hose has not been replaced or the filter
has not been properly screwed in after cleaning action.
Refit the cap on the emergency emptying hose or screw the filter fully in.
Unsatisfactory washing results:
Too little detergent or unsuitable detergent has been used.
Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
Check if you have selected the correct temperature.
Excessive laundry load.
Reduce the laundry load.
16
www.zanussi.com
Problem Possible cause/Solution
The door will not open:
The programme is still running.
Wait the end of washing cycle.
The door lock has not been released.
Wait a few minutes before opening the door.
There is water in the drum.
Select drain or spin programme to empty out the water.
The machine vibrates is noisy:
The transit bolts and packing have not been removed.
Check the correct installation of the appliance.
The support feet have not been adjusted
Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
Redistribute the laundry.
Maybe there is very little laundry in the drum.
Load more laundry.
Spinning starts late or the machine
does not spin:
The electronic unbalance detection device has cut in because the laundry is
not evenly distributed in the drum. The laundry is redistributed by reverse rota-
tion of the drum. This may happen several times before the unbalance disap-
pears and normal spinning can resume. If, after 10 minutes, the laundry is still
not evenly distributed in the drum, the machine will not spin. In this case, re-
distribute the load manually and select the spin programme.
Redistribute the laundry.
The load is too small.
Add more items, redistribute the load manually and then select the spinning
programme.
The machine makes an unusual
noise:
The machine is fitted with a type of motor which makes an unusual noise com-
pared with other traditional motors. This new motor ensures a softer start and
more even distribution of the laundry in the drum when spinning, as well as
increased stability of the machine.
No water is visible in the drum:
Machines based on modern technology operate very economically using very
little water without affecting performance.
If you are unable to identify or solve the problem, contact
our service centre. Before telephoning, make a note of the
model, serial number and purchase date of your machine:
the Service Centre will require this information.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
Mod
.
.
.
. ..
.
...
Prod. N
o.
... ...
.
.
S
e
r
.
No
.
... ... ...
17
www.zanussi.com
Technical data
Dimensions Width
Height
Depth
60 cm
85 cm
54 cm
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate, on the
inner edge of the appliance door.
Water supply pressure Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load Cotton 6 kg
Spin Speed Maximum 1000 rpm
Consumption values
Programme Energy consumption
(KWh)
1)
Water consumption
(litre)
1)
Programme duration
(Minutes)
1)
White Cottons 90 °C 2.0 61 140
Cottons 60 °C 1.35 58 125
Cottons 40 °C 0.75 58 120
Synthetics 40 °C 0.9 50 90
Delicates 40 °C 0.55 58 70
Wool/ Handwash 30 °C 0.25 58 60
1) The consumption information shown in this chart is indicative. It can vary depending on the quantity and the type of laundry, on the
temperature of the water supply and on the ambient temperature.
Standard programmes for the Energy Label consumption
values
The cotton 60 °C economy and cotton 40 °C economy are
the standard cotton programmes for normally soiled cot-
ton laundry. They are suitable to clean normally soiled
cotton laundry and they are the most efficient programmes
in terms of combined energy and water consumption for
washing that type of cotton laundry.
They agree with EN60456.
The actual water temperature may differ from the de-
clared cycle temperature.
Installation
Unpacking
All transit bolts and packing must be removed before us-
ing the appliance.
You are advised to keep all transit devices so that they can
be refitted if the machine ever has to be transported again.
18
www.zanussi.com
After removing all the
packaging, carefully lay
machine on it's back to re-
move the polystyrene base
from the bottom.
Remove the power supply
cable and the hoses from
the hose holders on the
rear of the appliance.
Unscrew the three bolts
with the supplied spanner.
Slide out the relevant plas-
tic spacers.
Fill the smaller upper hole and the two large ones with
the corresponding plastic plug caps supplied in the bag
containing the instruction booklet.
Positioning
Install the machine on a flat hard floor. Make sure that air
circulation around the machine is not impeded by carpets,
rugs etc. Check that the machine does not touch the wall
or other kitchen units.
Level the washing ma-
chine by raising or lower-
ing the feet. The feet may
be tight to adjust as they
incorporate a self locking
nut, but the machine
MUST be level and stable.
If necessary, check the
setting with a spirit level.
Any necessary adjustment
can be made with a span-
ner.
Accurate levelling prevents vibration, noise and displace-
ment of the machine during operation.
Caution! Never place cardboard, wood or similar
materials under the machine to compensate for any
unevenness in the floor. After having levelled the
appliance, tighten the lock nuts.
Raising the appliance
Suspended wooden floors are particularly susceptible to
vibration.
To help prevent vibration we recommend you place a wa-
terproof wood panel, at least 15 mm thick under the appli-
ance, secured to at least 2 floor beams with screws, the
wood panel must extend beyond the front feet.
If possible install the appliance in one of the corners of
the room, where the floor is more stable.
Water inlet
Warning! This appliance must be connected to a
cold water supply
Caution! Before connecting up the appliance to new
pipework or to pipework that has not been used for
some time, run off a reasonable amount of water to flush
out any debris that may have collected
Caution! Do not use the hose from your previous
appliance to connect to water supply.
19
www.zanussi.com
Connect the hose to a tap
with a 3/4” thread. Always
use the hose supplied with
the appliance.
35°
45°
The other end of the inlet hose which connects to the
appliance can be turned as showed in the picture.
Do not place the inlet hose downwards. Angle the hose
to the left or right depending on the position of your
water tap. Set the hose correctly by loosening the ring
nut. After positioning the inlet hose, be sure to tighten
the ring nut again to prevent leaks.
Caution! The inlet hose must not be lengthened. If it
is too short and you do not wish to move the tap,
you will have to purchase a new, longer hose specially
designed for this type of use.
Water drainage
The end of the drain hose can be positioned in three ways:
Hooked over the edge of a
sink using the plastic hose
guide supplied with the
machine.
In this case, make sure the end cannot come unhooked
when the machine is emptying. This could be done by
tying it to the tap with a piece of string or attaching it to
the wall.
In a sink drain pipe branch. This branch must be above
the trap so that the bend is at least 60 cm above the
ground.
Directly into a drain pipe at a height of not less than 60
cm and not more than 90 cm. The end of the drain hose
must always be ventilated, i.e. the inside diameter of the
drain pipe must be larger than the outside diameter of
the drain hose. The drain hose must not be kinked.
Building in
This appliance has been designed to be built into the
kitchen furniture. The recess should have the dimensions
shown in picture A.
20
www.zanussi.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Zanussi ZWI1105 User manual

Category
Washing machines
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages